Materials Science and Engineering Commons^™

Focused-Based Multifractal Analysis Of The Wake In A Wind Turbine Array Utilizing Proper Orthogonal Decomposition, Naseem Ali, Hawwa Falih Kadum, Raúl Bayoán Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Hot-wire anemometry measurements have been performed in a 3×3 wind turbine array to study the multifractality of the turbulent kinetic energy dissipation. A multifractal spectrum and Hurst exponents are determined at nine locations downstream of the hub height, bottom and top tips. Higher multifractality is found at 0.5D and 1D downstream of the bottom tip and hub height. The second order of the Hurst exponent and combination factor shows the ability to predict the flow state in terms of its development. Snapshot proper orthogonal decomposition (POD) is used to identify the coherent and incoherent structures and to reconstruct the stochastic …

Large Scale Screening Of Low Cost Ferritic Steel Designs For Advanced Ultra Supercritical Boiler Using First Principles Methods, Lizhi Ouyang

Mathematical Sciences Faculty Research

Advanced Ultra Supercritical Boiler (AUSC) requires materials that can operate in corrosive environment at temperature and pressure as high as 760°C (or 1400°F) and 5000psi, respectively, while at the same time maintain good ductility at low temperature. We develop automated simulation software tools to enable fast large scale screening studies of candidate designs. While direct evaluation of creep rupture strength and ductility are currently not feasible, properties such as energy, elastic constants, surface energy, interface energy, and stack fault energy can be used to assess their relative ductility and creeping strength. We implemented software to automate the complex calculations to …

Loss-Induced Enhanced Transmission In Anisotropic Density-Near-Zero Acoustic Metamaterials, Chen Shen, Yun Jing

Henry M. Rowan College of Engineering Departmental Research

Anisotropic density-near-zero (ADNZ) acoustic metamaterials are investigated theoretically and numerically in this paper and are shown to exhibit extraordinary transmission enhancement when material loss is induced. The enhanced transmission is due to the enhanced propagating and evanescent wave modes inside the ADNZ medium thanks to the interplay of near-zero density, material loss, and high wave impedance matching in the propagation direction. The equi-frequency contour (EFC) is used to reveal whether the propagating wave mode is allowed in ADNZ metamaterials. Numerical simulations based on plate-type acoustic metamaterials with different material losses were performed to demonstrate collimation and subwavelength imaging enabled by …

Development Of Metal Matrix Composite Gridlines For Space Photovoltaics, Omar K. Abudayyeh

Chemical and Biological Engineering ETDs

Space vehicles today are primarily powered by multi-junction photovoltaic cells due to their high efficiency and high radiation hardness in the space environment. While multi-junction solar cells provide high efficiency, microcracks develop in the crystalline semiconductor due to a variety of reasons, including: growth defects, film stress due to lattice constant mismatch, and external mechanical stresses introduced during shipping, installation, and operation. These microcracks have the tendency to propagate through the different layers of the semiconductor reaching the metal gridlines of the cell, resulting in electrically isolated areas from the busbar region, ultimately lowering the power output of the cell …

Spray Printing Of Organic Semiconducting Single Crystals, Grigorios-Panagiotis Rigas, Marcia M. Payne, John E. Anthony, Peter N. Horton, Fernando A. Castro, Maxim Shkunov

Chemistry Faculty Publications

Single-crystal semiconductors have been at the forefront of scientific interest for more than 70 years, serving as the backbone of electronic devices. Inorganic single crystals are typically grown from a melt using time-consuming and energy-intensive processes. Organic semiconductor single crystals, however, can be grown using solution-based methods at room temperature in air, opening up the possibility of large-scale production of inexpensive electronics targeting applications ranging from field-effect transistors and light-emitting diodes to medical X-ray detectors. Here we demonstrate a low-cost, scalable spray-printing process to fabricate high-quality organic single crystals, based on various semiconducting small molecules on virtually any substrate by …

Avalanche Statistics From Data With Low Time Resolution, Michael Leblanc, Aya Nawano, Wendelin J. Wright, Xiaojun Gu, Jonathan T. Uhl, Karin A. Dahmen

Faculty Journal Articles

Extracting avalanche distributions from experimental microplasticity data can be hampered by limited time resolution. We compute the effects of low time resolution on avalanche size distributions and give quantitative criteria for diagnosing and circumventing problems associated with low time resolution. We show that traditional analysis of data obtained at low acquisition rates can lead to avalanche size distributions with incorrect power-law exponents or no power-law scaling at all. Furthermore, we demonstrate that it can lead to apparent data collapses with incorrect power-law and cutoff exponents. We propose new methods to analyze low-resolution stress-time series that can recover the size distribution …

Reduced Dimensionality Effects In Gd-Based Magnetocaloric Materials, Hillary Faith Belliveau

USF Tampa Graduate Theses and Dissertations

Magnetic refrigeration based on the magnetocaloric effect (MCE) is a promising alternative to conventional gas compression based cooling techniques. Understanding impacts of reduced dimensionality on the magnetocaloric response of a material such as Gadolinium (Gd) or its alloys is essential in optimizing the performance of cooling devices, which is also the overall goal of this thesis. We have determined, in the first part of the thesis, that laminate structures of pure Gd produced by magnetron sputtering have several disadvantages. The target material (pure Gd), ultra-high vacuum components, and the electrical energy it takes to run the manufacturing process are all …

Confinement Effects And Magnetic Interactions In Magnetic Nanostructures, Kristen Lee Stojak Repa

USF Tampa Graduate Theses and Dissertations

Multifunctional nanocomposites are promising for a variety of applications ranging from microwave devices to biomedicine. High demand exists for magnetically tunable nanocomposite materials. My thesis focuses on synthesis and characterization of novel nanomaterials such as polymer nanocomposites (PNCs) and multi-walled carbon nanotubes (MWCNTs) with magnetic nanoparticle (NP) fillers.

Magnetite (Fe₃O₄) and cobalt ferrite (CoFe2O4) NPs with controlled shape, size, and crystallinity were successfully synthesized and used as PNC fillers in a commercial polymer provided by the Rogers Corporation and poly(vinylidene fluoride). Magnetic and microwave experiments were conducted under frequencies of 1-6 GHz in the presence of …

Rapid Metal Design, Paul G. Sanders

TechTalks

Computational material design tools have advanced so that custom materials for specific applications can be designed and manufactured. In the case of metals, my team designs aluminum, iron, nickel, and copper (more to come) alloys using Thermo-Calc with Bayesian optimization. We design microstructures to deliver properties such as strength, conductivity, and corrosion resistance. Custom tailored materials are now practical solutions to engineering challenges, and materials engineers work on multi-disciplinary teams to deliver integrated, enhanced product designs.

Finite Element Simulation Of Pzt-Aided Interrogation Of Composite Laminates Exhibiting Damage, Amany Micheal, Yehia Bahei-El-Din

Centre for Advanced Materials

Piezoelectricity has proved effective in capturing changes in structures caused by various damage mechanisms. In one approach, piezoelectric wafer active sensors (PWAS) are mounted on the surface of the host structure and utilized as both actuators and sensors to interrogate the structure and monitor its health. This is achieved by subjecting the PWAS to a transient electric pulse and reading the resulting voltage. Changes in the stiffness of the substrate due to structural damage affect the response of the PWAS, which could be correlated to integrity of the structure. Applying this technique to fibrous composite laminates encounters particular challenges due …

Composite Metallic Nanofoam Structures, David Bahr, Matthew Howard, Mohamad Zbib, Raheleh Rahimi, John Balk

Composites at Lake Louise (CALL 2015)

Metallic nanofoams made of metals such as nickel (Ni) or gold (Au) with ligament sizes on the order of 10’s to 100’s of nm’s exhibit several remarkable properties as a consequence of their low relative density and high specific surface area, such as outstanding strength to weight ratios, enhanced plasmonic behavior and size-effect-enhanced catalytic behavior. However, these metallic nanofoams suffer from macroscopically brittle behavior due to plastic deformation in individual ligaments. With little or no barriers for slip, work-hardening is not possible within ligaments and extremely localized plasticity, once initiated, leads to a few ligaments necking and what appears to …

Characterization And Modeling To Design And Develop Tailored-Property Filled Glass Composites, Kevin Ewsuk

Composites at Lake Louise (CALL 2015)

Particle-filled-glass composites (FGCs) are being developed as new materials with structure and properties engineered for materials joining (e.g., for solid oxide fuel cells). Relative to conventional sealing glasses used to make hermetic glass-to-metal (GtM) seals, FGCs with tailored properties offer significant potential as more crack resistant hermetic seals with better performance and reliability. Additionally, compared to process sensitive crystallizable glasses, FGCs offer broader processing latitude and robustness, and afford greater control of seal microstructure and properties. FGCs are being developed using a combination of fundamental materials science and materials engineering, employing: 1) experimentally-validated molecular modeling to better understand and control …

Powerful Artificial Muscles For Morphing Composites And Other Applications, Ray Baughman

Composites at Lake Louise (CALL 2015)

Three successive generations of twist-spun artificial muscles are described and used to make morphing composites and textiles that are electrically, thermally, or chemically powered.¹ Our first generation of twist-spun muscles, which are electrochemically powered by volume changes induced by double-layer charge injection, provide torsional rotation speeds of 590 rpm, and torsional strokes of 250° per millimeter of actuator length, which is 1000 times that for earlier artificial muscles. Our second generation muscles, which require no electrolyte and are based on guest-infiltrated carbon nanotube yarns, can torsionally actuate at 11,500 rpm and deliver 85 times higher power density during contraction …

Open Source Database And Website To Provide Free And Open Access To Inactive U.S. Patents In The Public Domain, Yuenyong Nilsiam, Joshua M. Pearce

Department of Materials Science and Engineering Publications

Although theoretically the patent system is meant to bolster innovation, the current United States Patent and Trademark Office (USPTO) is cumbersome and involves a significant time investment to locate inactive patents less than 20 years old. This article reports on the development of an open source database to find these public domain ideas. First, a search strategy is explained. Then the operation and use of free and open source software are detailed to meet the needs of open hardware innovators. Finally, a case study is presented to demonstrate the utility of the approach with 3-D printing. The results showed how …

Deterministic Three-Dimensional Composite Structures For Energy Storage, Paul Brown

Composites at Lake Louise (CALL 2015)

Through mesoscale design of a 3D current collector, high power density and high energy density primary and secondary (rechargeable) large format and microbatteries (Figure 1) were fabricated. At the most fundamental level, mesostructuring enables optimization of the trade-off between energy and power density in energy storage systems due to unavoidable ohmic and other losses that occur during charge or discharge. Of course, it is at fast charge and discharge, where these effects are most important. By efficient design of the ion and electron transport pathways, we and others have shown it is possible to significantly improve the power-energy relationship. We …

Experimental And Computational Study On Fracture Mechanics Of Multilayered Structures, Hai Thanh Tran

USF Tampa Graduate Theses and Dissertations

Many devices in electronics are in the form of multilayered structures. These structures can fail catastrophically if they contain defects or cracks. Enhancing their fracture properties is therefore critical to improve the reliability of the systems. The interface-dominated fracture mechanics of multilayered structure was studied using experiments and finite element (FE) modeling by considering two examples: thin films on polymer substrates in flexible electronics and Cu leadframe/epoxy molding compound (EMC) in micro-electronics packaging.

In the first example, aluminum-manganese (Al-Mn) thin films with Mn concentration up to 20.5 at.% were deposited on polyimide (PI) substrates. A variety of phases, including supersaturated …

C-3 Examination Of Anodized Aluminum For Surface Defects After Thermal Cycles, Boon-Chai Ng

Celebration of Research and Creative Scholarship

A major cost in the fabrication of test sockets is the interposer, an interface layer that reroutes one connection to another. The interposer must have high resistivity with low loss, a smooth surface finish, high strength, resistance to chemicals involved in the process, and be extremely thin. Currently, the most common materials used for interposer are plastics, such as Torlon, Semitron, and PEEK. While these satisfy the requirements for test sockets, they do not perform well under higher ambient temperatures. Finding a less expensive, alternative material would be preferable.

In this study, anodized aluminum samples were subjected to repeat thermal …

Corrosion Characteristics Of Magnesium Under Varying Surface Roughness Conditions, Yahya Efe Yayoglu

USF Tampa Graduate Theses and Dissertations

The biggest challenge with magnesium alloy biodegradable implants is the rapid corrosion at the earlier stages of the healing process after implantation. In this research, the impact of surface roughness generated by different means on the corrosion rate of AZ31 magnesium alloy in a simulated biologic environment is investigated. In order to perform accurate experimentation, an in vitro setup is assembled that simulates the human body environment accurately has been prepared using Schinhammer’s in vitro immersion testing setup and Kokubo’s Simulated Body Fluid (SBF). For the immersion test of Mg in SBF, several surface texture groups of Mg have been …

Synthesis, Characterization, And Application Of Monosized Mesoporous Silica Nanoparticle-Supported Lipid Bilayers For Targeted Therapeutic Delivery To Individual Cells, Paul Durfee

Biomedical Engineering ETDs

Mesoporous silica nanoparticle (MSNP) supported-lipid bilayers, termed ‘protocells,’ represent a potentially transformative class of therapeutic and theranostic delivery vehicles. The field of targeted drug delivery poses considerable challenges that cannot be addressed with a single ‘magic bullet’. Consequently, the protocell has been designed as a modular platform composed of interchangeable biocompatible components. The mesoporous silica core can have variable size and shape to direct biodistribution and controlled pore size and surface chemistry to accommodate diverse cargos. The encapsulating supported lipid bilayer can be modified with targeting and trafficking ligands as well as polyethylene glycol (PEG) to effect selective binding, endosomal …

Biomarker Detection At Risk Forecasting Level Using Metal-Enhanced Fluorescence Combined With Surface Acoustic Wave, Jun Liu

USF Tampa Graduate Theses and Dissertations

In this paper, metal-enhanced fluorescence (MEF) technique is used to lower the detection limit of carcinoembryonic antigen (CEA) which is able to be utilized in forecasting the risk of having certain kinds of cancers, especially colon and rectal cancer. By incubating silver nanocubes (Ag NCs) on the surface of the chips, the detection limit goes down to below 1ng/mL of CEA. Also, when combining MEF with surface acoustic wave (SAW) devices, the incubation time between antigen and antibody will decrease significantly with the fluorescence signal keeping similar or higher level.