Materials Science and Engineering Commons^™

Electromigration Induced Interface Reaction In Cu-Wire / Al-Pad Diffusion Couple, Patricia Aracelly Rodriguez-Salazar

Material Science and Engineering Dissertations - Archive

This dissertation presents experimental observations that may assist the understanding of electromigration (EM) failure mechanism active in Cu wire and Al thin film pad (wire bond). This study is motivated by an ongoing industrial effort to adapt Cu as wire bonding material for interconnection. Traditional material used for the wire bond has been Au; however, its high cost combined with its susceptibility to reliability failure caused by excessive growth of IMCs (IMC) makes Cu to be an attractive replacement. Though, since an application of Cu to wire bond technology is relatively new, many of reliability failure mechanisms are unknown especially …

Investigating Co2 Removal By Ca- And Mg-Based Sorbents With Application To Indoor Air Treatment, Elliott T. Gall, Cem Sonat, William W. Nazaroff, Cise Unluer

Mechanical and Materials Engineering Faculty Publications and Presentations

Indoor carbon dioxide (CO 2 ) levels serve as an indicator of ventilation sufficiency in relation to metabolic effluents. Recent evidence suggests that elevated CO 2 exposure (with or without other bioeffluents) may cause adverse cognitive effects. In shelter-in-place (SIP) facilities, indoor CO 2 levels may become particularly elevated. This study evaluates four low-cost alkaline earth metal oxides and hydroxides as CO 2 sorbents for potential use in indoor air cleaning applications. Sorbents studied were MgO, Mg(OH) 2 , Ca(OH) 2 and commercially available soda lime. Uncarbonated sorbents characterized with nitrogen adsorption porosimetry showed BET surface areas in the 5.6–27 …

Size Scaling Of Strength And Toughness For 3d Printed Polymer Specimens, Darren Thomas Bell

Open Access Theses

To find material systems that offer low density and high strength, stiffness or toughness, hierarchically designed material systems have provided a promising research area. This thesis lays the groundwork for designing efficient micro-architectured material systems by characterizing size effects for 3d printed polymer parts. Two methods were used to analyze data from 3-point bend tests for specimens of varying size: the load-separation method was used for finding the point of crack growth initiation and Bazant’s method was used to find shape independent strength at failure. The strength values were used as inputs for finding size independent material constants within a …

Mechanism Of Shot Peening Enhancement For The Fatigue Performance Of Aa7050-T7451, Daniel James Chadwick

Open Access Theses

Shot peening is a dynamic cold working process involving the impingement of peening media onto a substrate surface. Shot peening is commonly employed as a surface treatment technique within the aerospace industry during manufacturing, in order to improve fatigue performance of structural components. The compressive residual stress induced during shot peening is understood to result in fatigue crack growth retardation, improving the performance of shot peened components. However, shot peening is a compromise between the benefit of inducing a compressive residual stress and causing detrimental surface damage. Due to the relatively soft nature of AA7050-T7451, shot peening can result in …

Design Of Nitroxide-Based Radical Polymer Materials For Electronic Applications, Martha E. Hay

Open Access Theses

Radical polymers represent a new class of organic electronic materials that rely on an oxidation-reduction (redox) reaction to transport charge. That is, stable radical sites pendant to the polymer backbone communicate electronically through a rapid oxidation-reduction reaction. This redox mechanism has previously been established as effective for charge-storage applications (e.g., secondary batteries). When applied in the solid state, radical polymers demonstrate electrical conductivity on par with that of first-generation conjugated polymer electronic materials. This initial success has prompted interest in developing design rules for radical polymers. Specifically, this thesis explores the impact of radical density in a polymer …

Degradation Of High Performance Polymeric Fibers: Effects Of Sonication, Humidity And Temperature On Poly (P-Phenylene Terephthalamide) Fibers, Nelyan Lopez-Perez

Open Access Theses

High performance fibers are characterized by properties such as high strength and resistance to chemicals and heat. Due to their outstanding properties, they are used on applications under harsh environments that can degrade and decrease their performance. Fiber degradation due to different chemical and mechanical factors, is a process that begins at a microstructural level. Changes in the polymer’s chemical or physical structure can alter their mechanical properties. Knowledge of the structure-properties relationship and the effects of environmental chemical and physical factors over time, is crucial for the improvement and development of high performance fibers.

In this study ballistic fibers …

Linking Nanoscale Mechanical Behavior To Bulk Physical Properties And Phenomena Of Energetic Materials, Matthew R. Taw

Open Access Theses

The hardness and reduced modulus of aspirin, RDX, HMX, TATB, FOX-7, ADAAF, and TNT/CL-20 were experimentally measured with nanoindentation. These values are reported for the first time using as-received micron sized crystals of energetic materials with no additional mechanical processing. The results for TATB, ADAAF, and TNT/CL-20 are the first of their kind, while comparisons to previous nanoindentation studies on large, carefully grown single crystals of the other energetic materials show that mechanical properties of the larger crystals are comparable to crystals in the condition they are practically used. Measurements on aspirin demonstrate the variation that can occur between nanoindentation …

The Influence Of Alkalinity Of Portland Cement On The Absorption Characteristics Of Superabsorbent Polymers (Sap) For Use In Internally Cured Concrete, Juan D. Tabares Tamayo

Open Access Theses

The concrete industry increasingly emphasizes advances in novel materials that promote construction of more resilient infrastructure. Due to its potential to improve concrete durability, internal curing (IC) of concrete by means of superabsorbent polymers (SAP) has been identified as one of the most promising technologies of the 21st century. The addition of superabsorbent polymers into a cementitious system promotes further hydration of cement by providing internal moisture during the hardening and strength development periods, and thus limits self-desiccation, shrinkage, and cracking.

This thesis presents the work performed on the series of cement pastes with varying alkalinity of their pore solutions …

Thermomechanical Properties Of Novel Lanthanum Zirconate Based Thermal Barrier Coatings - An Integrated Experimental And Modeling Study, Xingye Guo

Open Access Dissertations

Thermal barrier coatings (TBCs) are refractory materials deposited on gas turbine components, which provide thermal protection for metallic components at operating conditions. The current state-of-art TBC material is yttria-stabilized zirconia (YSZ), whose service temperature is limited to 1200 celsius, due to sintering and phase transition at higher temperatures. In comparison, lanthanum zirconate (La2Zr2O7, LZ) has become a promising candidate material for TBCs due to its lower thermal conductivity and higher phase stability compared to YSZ.

The primary objective of this thesis is to design a novel robust LZ-based TBC system suitable for applications beyond 1200 celsius. Due to LZ’s low …

Plasmonic Devices Based On Transparent Conducting Oxides For Near Infrared Applications, Kim Jongbum

Open Access Dissertations

In the past decade, there have been many breakthroughs in the field of plasmonics and nanophotonics that have enabled optical devices with unprecedented functionalities. Even though remarkable demonstration of at photonic devices has been reported, constituent materials are limited to the noble metals such as gold (Au) and silver (Ag) due to their abundance of free electrons which enable the support of plasmon resonances in the visible range. With the strong demand for extension of the optical range of plasmonic applications, it is now a necessity to explore and develop alternative materials which can overcome intrinsic issues of noble metals …

Energy Localization And Heat Generation In Composite Energetic Systems Under High-Frequency Mechanical Excitation, Jesus O. Mares

Open Access Dissertations

In this work, the ability to use high frequency mechanical excitation to generate significant heating within plastic bonded explosives, as well as single energetic particles embedded within a viscoelastic binder, is studied. In this work, the fundamental mechanisms associated with the conversion of high-frequency mechanical excitation to heat as applied to these composite energetic systems are thoroughly investigated.

High-frequency contact excitation has been used to generate a significant amount of heat within samples of PBX 9501 and representative inert mock materials. Surface temperature rises on the order of 10 °C were observed at certain frequencies over a range from 50 …

Bridge Maintenance To Enhance Corrosion Resistance And Performance Of Steel Girder Bridges, Luis M. Moran Yanez

Open Access Dissertations

The integrity and efficiency of any national highway system relies on the condition of the various components. Bridges are fundamental elements of a highway system, representing an important investment and a strategic link that facilitates the transport of persons and goods. The cost to rehabilitate or replace a highway bridge represents an important expenditure to the owner, who needs to evaluate the correct time to assume that cost. Among the several factors that affect the condition of steel highway bridges, corrosion is identified as the main problem. In the USA corrosion is the primary cause of structurally deficient steel bridges. …

Microstructural Evolution During The Homogenization Heat Treatment Of 6xxx And 7xxx Aluminum Alloys, Pikee Priya

Open Access Dissertations

Homogenization heat treatment of as-cast billets is an important step in the processing of aluminum extrusions. Microstructural evolution during homogenization involves elimination of the eutectic morphology by spheroidisation of the interdendritic phases, minimization of the microsegregation across the grains through diffusion, dissolution of the low-melting phases, which enhances the surface finish of the extrusions, and precipitation of nano-sized dispersoids (for Cr-, Zr-, Mn-, Sc-containing alloys), which inhibit grain boundary motion to prevent recrystallization. Post-homogenization cooling reprecipitates some of the phases, changing the flow stress required for subsequent extrusion. These precipitates, however, are deleterious for the mechanical properties of the alloy …

Ballistic Resistance Of Plain Woven P-Aramid Fabrics, B Kusuktham, S Udon, M Jitjaicham

Journal of Metals, Materials and Minerals

This research investigated the ballistic resistance of p-Aramid fabric. Plain woven aramid fabrics were prepared to produce bulletproof vest having 5 kg of 32 fabric layers. The performance of the multilayer aramid fabrics in terms of ballistic resistance was evaluated by ballistic testing with the difference types of bullet. The damage of the fabric and the indentation of modeling clay behind the target were examined. The results showed that vests prepared from 18 - 32 fabric layers exhibited the ballistic resistance; the more the fabric layer the more the resistance performance. In addition, the indentation of the modeling clay decreased …

Compressive Properties And Imaging Analysis Of A New Metal Foam-Natural Rubber Hybrid Structure, A Chaturvedi, G Sanyal, S Chaturvedi, As Patil

Journal of Metals, Materials and Minerals

In this study an attempt has been made to create a new hybrid structure. The hybrid structure has been made by hierarchically combining closed cell Aluminum foam and natural rubber. The hybrid structure, when subjected to compressive loading, displayed improved energy absorption characteristics compared to its parent monoliths. It also displayed significant strain recovery post deformation. High resolution imaging was also carried out to compare the internal structure of hybrid samples before and after compression. Critical discussion of the experimental results has been made.

Microstructure And Properties Of Spark Plasma Sintered Moalb Ceramics, Ting Lou

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Molybdenum aluminum boride (MoAlB) is a ternary transition metal boride which has promising aeronautic and nuclear applications. It inheres excellent properties of the binary transitional metal borides (e.g., MoB, ZrB₂) such as high melting temperature, high hardness, and thermal conductivity. Besides, MoAlB is superior to MoB because: (1) the Al element provides an oxidation resistance at high temperatures; (2) its nanolaminated structure consisting of M-B layers with alternating Al layers results in a unique damage tolerance property. In this research, polycrystalline MoAlB have been successfully synthesized and simultaneously sintered using spark plasma sintering (SPS) from molybdenum boride (MoB) …

Optimal Grading For Strength And Functionality Of Parts Made Of Interpenetrating Polymer Networks: Load Capacity Enhancement, Zhong Chen

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Uniform parts with stress concentrations or singularities are prone to failure under relatively small loads, which motivates researchers to seek methods to enhance the strength of these parts. This dissertation studies the optimization of material grading to design parts made of functionally graded interpenetrating polymer networks (FG-IPNs) to improve their load capacity.

An acrylate/epoxy IPN with variations of elastic Young’s modulus, Poisson’s ratio, and ultimate stress at failure is used for optimization of a plate with stress concentration. The grading is optimized by attaching the finite element method (FEM) solver to a general purpose bound-constrained optimizer. Two examples, a plate …

Quantification Of Volatile Residuals In Polydioxanone By Gas Chromatography: Method Development, Validation And Implementation, Clayton Joseph Culbreath

All Theses

Bioresorbable polymers are increasingly utilized for implantable medical devices to avoid complications related to explant and/or long term responses to foreign materials. As with all polymeric materials, residual levels of unreacted monomer, and other volatiles, drastically affect the mechanical and chemical properties as well as the parameters required to process the material into a device. The 1,4-dioxane-2-one (PDO) monomer is a six membered ring that forms an ether-ester polymer via ring-opening polymerization (ROP) with intermediate absorption rate properties that are ideal for numerous implant situations. Developing devices using poly(1,4-dioxane-2-one) (PPDO, PDO, PDX, PPDX, or PDS) is complicated by residual levels …

Fabrication Of Infrared Photodetectors Utilizing Lead Selenide Nanocrystals, Justin Anthony Hill

Graduate Theses and Dissertations

Colloidal lead selenide and lead selenide / lead sulfide core/shell nanocrystals were grown using a wet chemical synthesis procedure. Absorbance and photoluminescence measurements were made to verify the quality of the produced nanocrystals. Absorbance spectra were measured at room temperature, while photoluminescence spectra were measured at 77 K. Organic ligands were exchanged for shorter ligands in order to increase the conductivity of the nanocrystals. Absorption and PL spectra for both core and core/shell nanocrystals were compared. Interdigital photodetector devices with varying channel widths were fabricated by depositing gold onto a glass substrate. Lead selenide nanocrystals were deposited onto these metallic …

Interactive Physics And Characteristics Of Photons And Photoelectrons In Hyperbranched Zinc Oxide Nanostructures, Garrett Edward Torix

Graduate Theses and Dissertations

As is commonly known, the world is full of technological wonders, where a multitude of electronic devices and instruments continuously help push the boundaries of scientific knowledge and discovery. These new devices and instruments of science must be utilized at peak efficiency in order to benefit humanity with the most advanced scientific knowledge. In order to attain this level of efficiency, the materials which make up these electronics, or possibly more important, the fundamental characteristics of these materials, must be fully understood. The following research attempted to uncover the properties and characteristics of a selected family of materials. Herein, zinc …