Materials Science and Engineering Commons^™

An Electrochemical Investigation In The Anticorrosive Properties Of Silver Nanoparticles For The Acidic Corrosion Of Aluminium, H. A. Fetouh, B. A. Abd-El-Nabey, Y. M. Goher, M. S. Karam

Journal of Electrochemistry

The mass loss, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques were used for the determinations of the corrosion rates for aluminium in 1.0 mol·L^-1 hydrochloric acid (HCl) solutions both in the absence and presence of silver nanoparticles (SNPs) at 30 ℃. The protection efficiency was evaluated to be 96.4% for 0.014 g·L^-1 of the SNPs. It has been found that the capacity of the electrical double layer at the aluminium/solution interface was decreased with increasing the concentration of the SNPs, indicating that the SNPs were adsorbed at the aluminium surface. The Langmuir adsorption isotherm and the kinetic-thermodynamic …

Deposition Mechanism And Coating Characterization For The Trivalent Chromium Electrodeposition In Sulphate Electrolyte, Hui Yan, Shuai-Shuai Huang, Fang-Zu Yang, Zhong-Qun Tian, Shao-Min Zhou

Journal of Electrochemistry

Linear sweep voltammetry (LSV) and cyclic voltammetry (CV) were used to study the electrodeposition mechanism of trivalent chromium on a copper electrode in the novel sulphate electrolyte for thick trivalent chromium plating. The thickness, morphology, composition, microhardness, and structure, as well as the corrosion resistance in 3.5wt% NaCl solution of the trivalent chromium coatings were investigated by X-ray fluorescence gage, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), microhardness tester, X-ray diffraction (XRD) and Tafel curve measurements. The results showed that the electrodeposition of trivalent chromium involved two consecutive one electron reduction steps. The first step, Cr³⁺ + e …

Applications Of Electrospinning In Lithium-Air Batteries, Yue Fu, Jin Wang, Hai-Yang Yu, Jing-Hua Tian, Rui-Zhi Yang

Journal of Electrochemistry

Lithium-air batteries have received increasing attention as the “ultimate batteries” due to their extremely high theoretical capacity and environment friendly. However, there are still many obstacles hindering the wide applications of the lithium-air batteries owing to the limitations of large charge-discharge over-potentials, poor Columbic efficiency and cycling performance. Exploring of high-efficiency, low-cost and eco-friendly catalysts is one of the vital issues for lithium-air batteries. Meanwhile, electrospinning techniques have been under substantial developments due to its simple fabrication process, high efficiency and production. This paper reviews the recent progresses in fabrications of various novel catalysts for lithium-air batteries with electrospinning techniques, …

Effect Of Molecular Side Groups And Local Nanoenvironment On Photodegradation And Its Reversibility, Nicole Quist, Mark Li, Ryan Tollefsen, Michael Haley, John Anthony, Oksana Ostroverkhova

Chemistry Faculty Publications

Degradation of organic semiconductors in the presence of oxygen is one of the bottlenecks preventing their wide-spread use in optoelectronic devices. The first step towards such degradation in functionalized pentacene (Pn) derivatives is formation of endoperoxide (EPO), which can either revert back to the parent molecule or proceed to molecule decomposition. We present the study of reversibility of EPO formation through probing the photophysical properties of functionalized fluorinated pentacene (Pn-R-F8) derivatives. Experiments are done in solutions and in films both at the single molecule level and in the bulk. In solutions, degradation of optical absorption and its partial recovery after …

Distributions Of Pore Sizes And Atomic Densities In Binary Glasses Revealed By Molecular Dynamics Simulations, Nikolai V. Priezjev, Maxim A. Makeev

Mechanical and Materials Engineering Faculty Publications

We report on the results of a molecular dynamics simulation study of porous glassy media, formed in the process of isochoric rapid quenching from a high-temperature liquid state. The transition to a porous solid occurs due to the concurrent processes of phase separation and material solidification. The study is focused on topographies of the model porous structures and their dependence on temperature and average density. To quantify the pore-size distributions, we put forth a scaling relation that provides a satisfactory data collapse in systems with high porosity. We also find that the local density of the solid domains in the …

Wetting Properties Of Structured Interfaces Composed Of Surface-Attached Spherical Nanoparticles, Nikolai V. Priezjev, Bishal Bhattarai

Mechanical and Materials Engineering Faculty Publications

The influence of the external pressure and surface energy on the wetting transition at nanotextured interfaces is studied using molecular dynamics and continuum simulations. The surface roughness of the composite interface is introduced via an array of spherical nanoparticles with controlled wettability. We find that in the absence of an external pressure, the liquid interface is flat and its location relative to the solid substrate is determined by the particle size and the local contact angle. With increasing pressure on the liquid film, the interface becomes more curved and the three-phase contact line is displaced along the spherical surface but …

Supramolecular Aptamer Nano-Constructs For Receptor-Mediated Targeting And Light-Triggered Release Of Chemotherapeutics Into Cancer Cells, Deepak K. Prusty, Volker Adam, Reza M. Zadegan, Stephan Irsen, Michael Famulok

Materials Science and Engineering Faculty Publications and Presentations

Platforms for targeted drug-delivery must simultaneously exhibit serum stability, efficient directed cell internalization, and triggered drug release. Here, using lipid-mediated self-assembly of aptamers, we combine multiple structural motifs into a single nanoconstruct that targets hepatocyte growth factor receptor (cMet). The nanocarrier consists of lipidated versions of a cMet-binding aptamer and a separate lipidated GC-rich DNA hairpin motif loaded with intercalated doxorubicin. Multiple 2′,6′-dimethylazobenzene moieties are incorporated into the doxorubicin-binding motif to trigger the release of the chemotherapeutics by photoisomerization. The lipidated DNA scaffolds self-assemble into spherical hybrid-nanoconstructs that specifically bind cMet. The combined features of the nanocarriers increase serum nuclease …

Propeller Design Requirements For Quadcopters Utilizing Variable Pitch Propellers, Ian R. Mcandrew, Elena Navarro, Ken Witcher

Publications

Unmanned aerial vehicles, UAV, has increases in the drastically in these past several years since their costs reduced. This research is based and built upon previous research presented in a conference. With the advent of commercial Quadcopters, four propeller systems, are used, being designed and used to operate the advantages of both flight and hovering. The basic design of their propeller blades has not evolved from the early days of manned flight when wooden fixed blades were used. In this paper that expands upon previous findings and discussions it explores the historical developments. Furthermore, how the expansion and reduction in …

Recent Advances In Study Of Solid-Liquid Interfaces And Solidification Of Metals, Mohsen Asle Zaeem

Materials Science and Engineering Faculty Research & Creative Works

Solidification occurs in several material processing methods, such as in casting, welding, and laser additive manufacturing of metals, and it controls the nano- and microstructures, as well as the overall properties of the products. Recent advancements in experimental and computational modeling techniques have made it possible to more effectively study atomistic and microscale mechanisms that control the solidification nano- and microstructures, and formation and evolution of solidification defects.

Copper-Doped Lithium Triborate (Lib3o5) Crystals: A Photoluminescence, Thermoluminescence, And Electron Paramagnetic Resonance Study, Brant E. Kananen, John W. Mcclory, Nancy C. Giles, Larry E. Halliburton

Faculty Publications

When doped with copper ions, lithium borate materials are candidates for use in radiation dosimeters. Copper-doped lithium tetraborate (Li2B4O7) crystals have been widely studied, but little is known thus far about copper ions in lithium triborate (LiB3O5) crystals. In the present investigation, Cu+ ions (3d10) were diffused into an undoped LiB3O5 crystal at high temperature. These ions occupy both Li+ and interstitial positions in the crystal. A photoluminescence (PL) band peaking near 387 nm and a photoluminescence excitation (PLE) band peaking near 273 nm verify that a portion of these Cu+ ions are located at regular Li+ sites. After an …

Preparation And Characterization Of Nanocellulose And Its Application In Composite Materials, Xiuxuan Sun

LSU Doctoral Dissertations

Transparent cellulose films from 2,2,6,6-tetramethylpiperidine-1-oxyl radical oxidized cellulose nanocrystals (TOCNs) and 64 wt% sulfuric acid treated cellulose nanocrystals (SACNs) were prepared from bleached wood pulps. Film morphology, optical, mechanical, thermal, and surface wettability properties were characterized and compared. The results showed that TOCNs and SACNs had different average length, diameter, and aspect ratio.

The effect of cellulose nanofibers (CNFs) on flow, hydration, morphology, and strength of oil well cement (OWC) was investigated using a range of spectroscopic methods coupled with rheological modeling and strength analysis. The Vom-Berg model showed the best fitting result of the rheology data. The addition of …

Pit Evolution Around The Fusion Line Of A Nicrmov Steel Welded Joint Caused By Galvanic And Stress-Assisted Coupling Corrosion, Shuo Weng, Yuhui Huang, Fuzhen Xuan, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

The corrosion of NiCrMoV steel welded joints is performed in an aqueous solution of 3.5 wt% NaCl at 180 °C in a container at a pressure of 0.8 MPa. The specimens in the shape of cylindrical tensile rods are immersed in the aqueous solution under the action of tensile stress in a range of 0 to 0.9 of the yield stress of the base metal. The experimental results suggest that there is macro-galvanic corrosion in the welded joint with the coarse-grained heat affected zone (CGHAZ) as anode due to the highest corrosion susceptibility of the CGHAZ. The CGHAZ has the …

Correlation Of Structure, Function And Protein Dynamics In Gh7 Cellobiohydrolases From Trichoderma Atroviride, T. Reesei And T. Harzianum, Anna S. Borisova, Elena V. Eneyskaya, Suvamay Jana, Silke F. Badino, Jeppe Kari, Antonella Amore, Magnus Karlsson, Henrik Hansson, Mats Sandgren, Michael E. Himmel, Peter Westh, Christina M. Payne, Anna A. Kulminskaya, Jerry Ståhlberg

Chemical and Materials Engineering Faculty Publications

Background: The ascomycete fungus Trichoderma reesei is the predominant source of enzymes for industrial conversion of lignocellulose. Its glycoside hydrolase family 7 cellobiohydrolase (GH7 CBH) TreCel7A constitutes nearly half of the enzyme cocktail by weight and is the major workhorse in the cellulose hydrolysis process. The orthologs from Trichoderma atroviride (TatCel7A) and Trichoderma harzianum (ThaCel7A) show high sequence identity with TreCel7A, ~ 80%, and represent naturally evolved combinations of cellulose-binding tunnel-enclosing loop motifs, which have been suggested to influence intrinsic cellobiohydrolase properties, such as endo-initiation, processivity, and off-rate.

Results: The TatCel7A, ThaCel7A, …

Multifunctional Cerium-Based Nanomaterials And Methods For Producing The Same, Matthew O'Keefe, William Fahrenholtz, Carlos E. Castano Londono

Materials Science and Engineering Faculty Research & Creative Works

Embodiments relate to a cerium-containing nano-coating composition, the composition including an amorphous matrix including one or more of cerium oxide, cerium hydroxide, and cerium phosphate; and crystalline regions including one or more of crystalline cerium oxide, crystalline cerium hydroxide, and crystalline cerium phosphate. The diameter of each crystalline region is less than about 50 nanometers.

Effects Of Edge Inclination Angles On Whispering-Gallery Modes In Printable Wedge Microdisk Lasers, Cong Chen, Lei Wan, Hengky Chandrahalim

Faculty Publications

The ink-jet technique was developed to print the wedge polymer microdisk lasers. The characterization of these lasers was implemented using a free-space optics measurement setup. It was found that disks of larger edge inclination angles have a larger free spectral range (FSR) and a lower resonance wavelength difference between the fundamental transverse electric (TE) and transverse magnetic (TM) whispering-gallery modes (WGMs). This behavior was also confirmed with simulations based on the modified Oxborrow’s model with perfectly matched layers (PMLs), which was adopted to accurately calculate the eigenfrequencies, electric field distributions, and quality parameters of modes in the axisymmetric microdisk resonators. …

Comparison Of Eosin And Fluorescein Conjugates For The Photoinitiation Of Cell-Compatible Polymer Coatings, Jacob L. Lilly, Anuhya Gottipati, Calvin F. Cahall, Mohamed Agoub, Brad J. Berron

Chemical and Materials Engineering Faculty Publications

Targeted photopolymerization is the basis for multiple diagnostic and cell encapsulation technologies. While eosin is used in conjunction with tertiary amines as a water-soluble photoinitiation system, eosin is not widely sold as a conjugate with antibodies and other targeting biomolecules. Here we evaluate the utility of fluorescein-labeled bioconjugates to photopolymerize targeted coatings on live cells. We show that although fluorescein conjugates absorb approximately 50% less light energy than eosin in matched photopolymerization experiments using a 530 nm LED lamp, appreciable polymer thicknesses can still be formed in cell compatible environments with fluorescein photosensitization. At low photoinitiator density, eosin allows more …

A Preliminary Study Of Smithport Plain Bottle Morphology In The Southern Caddo Area, Robert Z. Selden Jr.

CRHR: Archaeology

This study expands upon a previous analysis of the Clarence H. Webb collection, which resulted in the identification of two discrete shapes used in the manufacture of the base and body of Smithport Plain bottles. The sample includes the Smithport Plain bottles from the Webb collection, and four new bottles: two previously repatriated specimens in the Pohler Collection, and two from the Mitchell site (41BW4) to test whether those specimens align morphologically with the Belcher Mound or Smithport Landing specimens. Results indicate significant allometry and a significant difference in Smithport Plain body and base shapes for bottles produced at the …

Improved Embedded Atom Method Potentials For Metal Hydride Systems, Robert Fuller

Theses, Dissertations and Capstones

Metal hydride systems are an important research topic in materials science because of their many practical, industrial, and scientific applications. Therefore, the development of reliable and efficient interatomic potentials for metal hydrides systems, to be utilized in molecular simulations, can be of great value in accelerating the research in this field. In this research, fully analytical interatomic Embedded Atom Method (EAM) potentials are developed for the PdAgH system. Ab initio simulations were performed to obtain the properties of selected PdAgH structures for fitting. The potentials are fit utilizing the central atom method without employing time-consuming molecular dynamics simulations in the …

Nitrogen-Doped Porous Carbon Derived From Bamboo Shoot As Solid Base Catalyst For Knoevenagel Condensation And Transesterification Reactions, Bingbing Mi, Xiufang Chen, Changle Jiang, Jingxin Wang, Xiujuan Chen, Bo Zhang, Xianmiao Liu, Zhijia Liu, Benhua Fei

Faculty & Staff Scholarship

Highly porous nitrogen-doped carbons derived from bamboo shoots (BSNCs) were prepared through an in-situ synthesis method. The results showed that BSNCs had a large specific surface area, a relatively high nitrogen content and hierarchically porous structures. The catalytic properties of BSNCs were evaluated based on Knoevenagel condensation and transesterification reactions. Deprotonated BSNC-700 exhibited high efficiency for the model reactions as a solid base catalyst, and the superior sample deprotonated in tBuOK solution with a concentration of 0.1 increased the conversion rate from 16.1% to 76.0% for Knoevenagel condensation. The two reactions proceeded smoothly in the presence of deprotonated BSNC-700. The …

Atomic Layer Deposition Of Molybdenum Disulfide Films Using Mof6 And H2S, Steven Letourneau, Elton Graugnard

Materials Science and Engineering Faculty Publications and Presentations

Molybdenum sulfide films were grown by atomic layer deposition on silicon and fused silica substrates using molybdenum hexafluoride (MoF₆) and hydrogen sulfide at 200 °C. In situ quartz crystal microbalance (QCM) measurements confirmed linear growth at 0.46 Å/cycle and self-limiting chemistry for both precursors. Analysis of the QCM step shapes indicated that MoS₂ is the reaction product, and this finding is supported by x-ray photoelectron spectroscopy measurements showing that Mo is predominantly in the Mo(IV) state. However, Raman spectroscopy and x-ray diffraction measurements failed to identify crystalline MoS₂ in the as-deposited films, and this might result …