Materials Science and Engineering Commons^™

Further Evaluation Of Speed Tables On Roadway Curves: Simulation And Expeditionary Deployments, Nathan Reineke

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The road network leading up to a United States military base is known as an Entry Control Facility, or ECF. Entry control facilities are used to shield military installations by monitoring vehicles and refusing access to unauthorized vehicles. Passive control devices, including speed tables, are used to disrupt or delay threat vehicles attempting to navigate ECFs at high speeds. The purpose of this research was to recommend optimized configurations of speed tables in combination with roadway curves which allow safe, efficient traversal for authorized vehicles and disruption or delay for threat vehicles.

First, an analytical model of a Tesla Model …

Automation And Upgrading Of Custom Cold Wall Uhv-Cvd Reactor For Group Iv Material Development, Alexander Golden

Graduate Theses and Dissertations

Group IV alloys have shown promising results for infrared optoelectronic applications where III-V materials are currently dominant. The III-V material system has vacancies that Group IV materials can fill, most importantly complementary metal oxide semiconductor (CMOS) process compatibility making quality devices much cheaper and widely available compared to the current state of the art. Silicon, being an indirect band gap Group IV material, has poor performance in optoelectronic applications but is the dominant material for most of the electronic industry. However, when silicon is alloyed or substituted with other group IV materials, these optoelectronic properties can be enhanced and, in …

Simulation Of Stress, Deformation, And Vibration In Unlubricated Ball Bearings At Varying Rotational Speeds, Billy Dwiki, Moh. Hartono

Journal of Mechanical Engineering Science and Technology (JMEST)

Bearings are critical components in rotating machinery, and their performance is highly influenced by operational factors such as rotational speed, load, and lubrication. This study aims to analyze the deformation, stress, and dynamic behavior of SAE 52100 bearings under dry operating conditions at various rotational speeds, as well as to propose mitigation strategies for high-speed industrial applications. A finite element simulation was conducted using ANSYS R19.2 to evaluate the total deformation, equivalent elastic strain, Von Mises stress, and vibrational characteristics of a 6204-type SAE 52100 bearing. The simulations were performed across a speed range of 600 to 2000 RPM under …

Optimizing Zeolite Catalysts For Efficient Ldpe Plastic Waste Pyrolysis, Hilda Porawati, Mazwan Mazwan, Sukadi Sukadi

Journal of Mechanical Engineering Science and Technology (JMEST)

The problem of plastic waste, particularly from low-density polyethylene (LDPE) plastic bags, poses a significant challenge in environmental management due to its non-biodegradable nature and widespread use in daily life. This study evaluates the influence of catalyst types on the characteristics and energy efficiency of liquid fuel products produced from LDPE waste pyrolysis. The three treatments compared were no catalysts, natural zeolite catalyst, and synthetic zeolite catalysts, each subjected to three different temperature variations: 250°C, 300°C, and 350°C. The observed parameters in this study were volume, product mass, cetane index, density, sulfur content, viscosity, flash point, calorific value, and energy …

Thermophysical, Rheological And Wear Resistance Of Canola Oil Biolubricant With Calcium Carbonate Additive Nanoparticle As Coolant In Cnc Machining, Alfandi Jaelani, Poppy Puspitasari, Diki Dwi Pramono, Alief Muhammad, Muhammad Kozin, Muhammad Kashif

Journal of Mechanical Engineering Science and Technology (JMEST)

Vegetable oil-based cutting fluids are of great importance in supporting green and sustainable manufacturing. This research introduces a new groundbreaking vegetable lubricant formulated with canola oil as the base material, coupled with CaCO3 nanoparticles synthesized from scallop shell waste and used as a cutting fluid in the AISI 1045 CNC machining process steel sprayed with minimum quantity lubrication (MQL). This investigation delves into the thermophysical, rheological, and wear resistance of the developed bio-lubricant. The results of this analysis show density value increased in the canola + CaCO3 0.15% sample by 3.28% of the pure canola sample, as did the viscosity …

Improvement Of Thermal Energy Storage Performance In Al-Al2o3 Composites Through Additions Of Copper: Evaluation Of Microstructure And Thermal Properties, Muhammad Hasan Basri, Ramang Magga, Muhammad Syaiful Fadly, Zikri Arifansyah Djaba, Muhammad Iqbal Ibrahim, Hidayat Hidayat, Yandi Yandi

Journal of Mechanical Engineering Science and Technology (JMEST)

The study aims to evaluate the influence of adding copper aluminum–alumina composite (Al–Al₂O₃) against characteristic thermal properties through metallurgical powder. Three variations of the composition of weight copper were used, namely 5%, 10%, and 15%, with aluminum as the matrix and alumina as the reinforcement. Thermal test covering analysis of thermal conductivity, specific heat, and microstructure characterization using SEM-EDX. The results show that adding Cu increases thermal conductivity significantly, with the highest mark achieved in the 15% Cu composite (6.47 W/m.°C). However, the increase in Cu content above 10% causes the agglomeration of particles and enhancements in porosity, which harms …

Numerical Investigation Of Ethanol-Enriched Diesel And Biodiesel Fuels In A Diesel Engine, Annisa Bhikuning, Hezron Elyakim Potto, Sandi Apriandi Setiawan, Jamal F. Jati

Journal of Mechanical Engineering Science and Technology (JMEST)

This study explores the effects of ethanol blending on the performance and emissions of a compression ignition (CI) engine using both diesel and biodiesel as base fuels. Motivated by increasing environmental concerns regarding pollutant emissions from conventional diesel engines, ethanol was introduced as an oxygenated additive to improve combustion characteristics and reduce the formation of harmful exhaust emissions. Ethanol’s high oxygen content promotes more complete combustion, potentially lowering carbon-based emissions such as carbon monoxide (CO), particulate matter (PM), and unburned hydrocarbons. In this study, performance and emission parameters were simulated using Diesel-RK software at various engine speeds of 1500, 2000, …

One-Way Thermal-Fluid-Solid Coupling Analysis Of Helicopter Tail Reducer With Spiral Bevel Gear, Dongping Sheng, Zhongyuan Ma, Chenqi Zhou, Haidong Feng, Hun Guo, Chun Su

Journal of Mechanical Engineering Science and Technology (JMEST)

This research focuses on investigating the thermal-fluid-solid coupling behavior within spiral bevel gears to enhance the bearing capacity and extend the operational service life of the gear reducer located in the helicopter tail gearbox. The study commences by constructing detailed, parametrically defined threedimensional digital models. These models accurately represent the critical components: the spiral bevel gear itself, the surrounding gearbox housing, and the supporting gear shaft, based directly on the specifications of an actual helicopter tail reducer assembly. Subsequently, the analysis proceeds with a one-way, steadystate thermal-solid coupling simulation performed on the established model assembly. This critical simulation phase aims …

The Impact Of Pine Resin-Epoxy Ratios On Fire Resistance And Acoustic Performance Of Banana Fiber Composites, Cokorda Istri Putri Kusuma Kencanawati, Dewa Ngakan Ketut Putra Negara, I Gede Andy Andika Parahita

Journal of Mechanical Engineering Science and Technology (JMEST)

Because of their low environmental impact and biodegradability, composite materials derived from natural fibers and resins have drawn interest as sustainable substitutes for synthetic materials in thermal and acoustic applications. Two promising natural components are banana stem fiber and pine resin, but they need to be modified due to their mechanical limitations and flammability. Epoxy resin is commonly used to enhance structural performance; however, its effects on acoustic and fire resistance properties require further investigation. This study examined how different epoxy resin contents affected the sound absorption and fire resistance of composites made from banana stem fiber and pine resin. …

Effect Of Argon Gas Flow Rate On Crystal Structure, Morphology, And Optical Properties Of Cigs Film For Photodetector Applications, Nurul Lathi’I Fatul Chamidah, Fadilah Wulan Cahyani, I Gusti Ayu Isnaini Fatha Ramadhani, Erma Surya Yuliana, Nasikhudin Nasikhudin, Safwan Abd. Aziz, Nandang Mufti

Journal of Mechanical Engineering Science and Technology (JMEST)

CIGS material can be used as a material for photodetector applications. The deposition of CIGS thin films remains challenging. Generally, argon is used as a gas to bombard the CIGS material through the sputtering method. This study fabricated photodetectors by varying the argon gas flow rate (50-80 sccm) to investigate its effect on device performance. XRD, SEM, UV-Vis, and photoresponse tests were characterized. Structural analysis using XRD showed a weak (112) diffraction peak, indicating that the resulting film was not fully crystalline, but rather consisted of a nanocrystalline phase, even partly amorphous, with small crystallite sizes. According to the SEM …

Spray Angle On The Performance Of Split-Type Ac Condenser Installed On Concrete Rooftop In Tropical Climate, Kennedy Kennedy, I N Frenki Aryana, Basri Basri

Journal of Mechanical Engineering Science and Technology (JMEST)

This study investigated the influence of different water spray angles (0°, 15°, and 30°) on the thermal and energy performance of a split-type air-conditioning (AC) condenser installed on a concrete rooftop in a tropical climate. An experimental setup was designed to replicate actual concrete rooftop conditions, focusing on the condenser inlet temperature, compressor power consumption, and system coefficient of performance (COP). A 6-minute ON and 6-minute OFF intermittent spray cycle was employed to optimise water usage and minimise excessive humidity. Experimental measurements were conducted on a 9,000 Btu/h split-type unit equipped with a nozzle system connected to a 200 L …

The Effect Of Preheater On Heat And Mass Transfer Efficiency Using Rotating Drum Roaster, Melisa Surya Andini, Retno Wulandari, Heru Suryanto

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesia is the third-largest coffee producer globally, facing challenges including rising raw material costs, increased energy consumption, and unpredictable weather conditions. One potential solution is optimizing energy efficiency during roasting. This study investigates the effect of preheating on time and energy efficiency in heat and mass transfer by utilizing waste heat to preheat green Robusta coffee beans. The experiment was conducted on a laboratory scale using a rotating drum roaster with a double-layer drum made of stainless steel and clay, at 200 °C under atmospheric pressure. Two treatments were applied: roasting with a preheater and without, each repeated three times …

Impact Of Cpo And B35 On Diesel Engine Rocker Arm Wear During Long-Term Operation, Fawwaz Aqilah Nurmansyah, Nur Fadilah Rizky Supramono, Muhammad Ikhsan, Erwan Adi Saputro, Wiliandi Saputro

Journal of Mechanical Engineering Science and Technology (JMEST)

The increasing number of motor vehicles has led to higher fossil fuel consumption, contributing to greenhouse gas emissions, climate change, and environmental degradation. As a renewable alternative, biodiesel offers a way to reduce these impacts. Indonesia, with its abundant natural resources, has significant potential for biodiesel production. Crude palm oil (CPO) is a promising feedstock due to its availability and relatively low environmental impact. However, the high costs associated with the transesterification process make direct use of pre-heated CPO an area worth exploring. This study investigates the impact of pre-heated pure CPO compared to B35 ("Dexlite") on rocker arm wear …

Numerical Analysis Of The Effect Of Vortex Generator On The Aerodynamic Performance Of Naca 6412 Airfoils Using Large Eddy Simulation, Dedet Hermawan Setiabudi, Joan Bayuaji Nugroho, Eli Kumolosari, Lazuardy Rahendra Pinandhita, Okto Dinaryanto

Journal of Mechanical Engineering Science and Technology (JMEST)

Aerodynamic performance of an airfoil is significantly affected by flow separation, especially at high angles of attack. One common strategy to control flow separation is adding a triangular vortex generator (VG), which creates small vortices that help keep the airflow attached. The present study investigated the impact of triangular vortex generators on a NACA 6412 airfoil using Computational Fluid Dynamics (CFD) method. Large Eddy Simulation (LES) was applied due to its ability to show the vortices more clearly than other methods. It can also accurately capture the flow separation. To obtain the lift, drag, and lift-to-drag ratio (CL/CD) data, four …

The Effect Of Heat Treatment Duration On The Psychochemical, Mechanical, And Biodegradability Of Polyvinyl Alcohol/Gambir Extract Biocomposite Films, Ainul Kahfi Muhlasin, Poppy Puspitasari, Heru Suryanto, Diki Dwi Pramono, Dieter Rahmadiawan, Billie Jack Pasion

Journal of Mechanical Engineering Science and Technology (JMEST)

This study investigates PVA-based films with the addition of gambir and heat treatment to improve the characteristics of the film. Methods include the synthesis of PVA film with gambir addition (0.5%), treated by heat treatment for 40 minutes and 60 minutes. The film was characterised by physicochemical, mechanical properties, and biodegradability. Data was analyzed using ANOVA with a significance of 95%. Results indicate that the surface of PVA/gambir films is smoother and more homogeneous as the heat treatment duration increases. New peaks of functional groups were identified after the addition of gambir at the C-C and C-O groups. After heat …

Analysis Of Engine Parameters Of High Composition Palm Oil Biodiesel In Crdi System, Achmad Aminudin, Kelvin Dwi Wardana, Nanang Romandoni, Ahmad Yusril Aminullah, Nur Ihda Farikhatin Nisa, Hari Setiapraja

Journal of Mechanical Engineering Science and Technology (JMEST)

The heavy reliance on fossil fuels has serious consequences, particularly regarding increased greenhouse gas emissions that contribute to global warming. In order to obtain cleaner fuel resources and reduce fossil fuel dependence, palm oil biodiesel is added to fossil diesel by volume ratio resulting in B50 and B55 blends. Combustion characteristics, performance, fuel consumption, and emissions were performed in a diesel engine with a 4-cylinder common rail direct injection (CRDI) at different engine speeds (1500, 2000, 2500, and 3000 rpm). Compared to fossil diesel, biodiesel blends exhibit higher density at 855.9 kg/m³ (B55), kinematic viscosity with a value of 5.1 …

Surface Modification Of Local Natural Fibers Via Alkali Treatment For Improved Mechanical And Molecular Properties Of Bamboo Fiber, Pineapple Leaf Fiber, And Sisal Fiber, Jibril Maulana, Muhammad Ilman Nur Sasongko, Dewi Izzatus Tsamroh, Muchammad Yafis, Syekhan Maulana

Journal of Mechanical Engineering Science and Technology (JMEST)

A major development in materials science toward reinforcement materials in biopolymer composites has been caused by a worldwide trend toward sustainable manufacturing and the rise of the circular economy. However, their mechanical properties can often be affected by their hydrophilic properties, lack of surface compatibility, and their presence of molecular bonding, such as lignin and hemicellulose. Alkaline surface modification has been widely reported as an effective technique to increase structural stability and fibermatrix adhesion. This study evaluated the effects of alkalizing three types of local natural fibers—bamboo fiber (BF), pineapple leaf fiber (PALF), and sisal (SF)—with sodium hydroxide (NaOH) at …

Ai-Driven Innovations For Sustainable Healthcare Architecture In Developing Countries And Remote Areas: Enhancing Efficiency Through Futuristic Design, Esraa Elazab, Ahmed Eltawil

HBRC Journal

Access to healthcare in developing countries and remote areas remains a critical challenge due to geographic isolation, inadequate infrastructure, and limited medical resources. Communities in these regions face significant barriers in obtaining timely and adequate healthcare services, exacerbating public health issues. In response, artificial intelligence (AI) has emerged as a transformative technology, offering solutions that enhance healthcare systems by optimizing operational workflows, reducing human error, and improving resource management. When combined with sustainable design principles, AI-driven innovations provide a comprehensive approach to healthcare access and environmental sustainability. This paper presents a conceptual design proposal for a futuristic healthcare station aimed …

Best Practice Guidelines For Drafting Arbitration Clauses In Construction Contracts, Mohamed Abdel-Monem, Haitham Amer, Karim El Dash

HBRC Journal

Arbitration is a widely recognized method for resolving construction disputes, relying on the parties' mutual agreement and the enforceability of well-drafted clauses. This study examines the key elements that contribute to the effectiveness and validity of arbitration clauses in construction contracts. The aim is to provide practical drafting guidelines and a validated practitioner checklist. The research combined a comprehensive literature review, expert interviews, a pilot and final questionnaire survey involving 49 legal and engineering professionals, and real-world case study analyses. Data validation and thematic analysis were used to identify critical factors influencing the clarity, enforceability, and efficiency of arbitration clauses. …

Cycling Network Planning Through Urban Form Analysis: A Contextual Gis Model, Nora Osama Ahmed, Rania Adham Sayed, Mona Mahrous Abdel Wahed

HBRC Journal

Promoting cycling as a sustainable mode of urban mobility requires a deep understanding of how urban form influences cyclists’ route choices. This study investigates the influence of urban form on cyclists’ route selection in an attempt to enhance context-sensitive cycling network planning. Five factors of urban form density, transportation infrastructure, housing/building type, land use, and street layout are examined to determine if any of them have a contributing factor to route selection. Based on an extensive review of the literature, the research develops an Urban Form–Cyclist Route Priority Matrix (UF-CRP Matrix) that categorizes urban conditions into three levels of desirability …