Materials Science and Engineering Commons^™

The Effect Of Plasma Treatment On The Cure Behavior Of Out-Of-Life Prepregs And An Investigation Of The Mechanical Properties Of Composite Parts Manufactured From Plasma-Treated Prepregs, Monjur Morshed Rabby, Partha Pratim Das, Minhazur Rahman, Vamsee Vadlamudi, Rassel Raihan

Institute of Predictive Performance Methodologies (IPPM-UTARI)-Archive

Many industries, including aircraft, automobiles, and marine, are using prepreg (pre-impregnated fibers and a partially cured polymer matrix) to manufacture composite parts to achieve optimum fiber and resin volume ratio and part repeatability. Since prepregs have a short out oflife (i.e., the maximum storing time allowed at room temperature), they must be stored in refrigerators at low temperatures, which, if not maintained, have an unfavorable influence on the intended quality of the final product. For the present study, glass/epoxy prepregs (expired out-life) were plasmatreated before being used to make the composite part to compensate for the room temperature aging effect. …

Designing Physical And Chemical Confinement In Lithium Sulfur Battery Cathode For Suppression Of Shuttle Effect, Saisaban Fahad

Electronic Theses and Dissertations, 2020-2023

Lithium sulfur batteries (LSBs) are attracting attention as a next generation energy storage device because of their high energy density (2670WhKg-1), high specific capacity (1675 mAhg-1), low cost and environmental friendliness. However, there are several challenges that need to be overcome before LSBs can be implemented in general applications. This is due to the low electric conductivities of sulfur and lithium sulfide and large volume changes during charge/discharge cycling. Also, most importantly, the dissolution of lithium polysulfides into the electrolyte during cycling leads to capacity decay and low coulombic efficiency. Additionally, these lithium polysulfides can diffuse to the lithium anode …

A Computational Exploration Of The Scandate Cathode Surface, Shankar Miller-Murthy

Theses and Dissertations--Chemical and Materials Engineering

The exact surface configuration of scandate cathodes has been a point of contention for the materials community for a long time. Without proper understanding of it and the related structures and emission mechanisms, scandate cathodes remain patchy and unreliable emitters. Thus, density functional theory techniques were applied to various potential surface arrangements and found that there are several low-energy surfaces with low work functions that incorporate a scandium interlayer between tungsten and oxygen or otherwise have a scandium-on-tungsten structure. Furthermore, it was discovered that adding a monolayer of scandium directly to a tungsten surface is surprisingly favorable, thermodynamically. While none …

Pitch-Based Carbon Fiber Derived From Coal Extract Liquids, Cierra Danielle Crowe

Theses and Dissertations--Chemical and Materials Engineering

Limited coal coking operations and the use of coal-tar pitch as a binding agent in the production of metallurgical anodes has led to a limited availability of coal tar pitch for carbon fiber products. This has sparked interest in utilizing non-metallurgical coal-based liquids as an alternative to traditional coal tar from metcoke operations. This can be achieved by low severity solvent extraction, with heavy aromatic solvents, to produce coal liquids that act as precursor to pitch-based carbon fiber. This thesis aims to establish the processing and determine the impact of utilizing coal liquids to produce carbon fiber. In this work …

Green-Route Synthesis Of Halide Perovskite Materials And Their Optoelectronic Properties, Xiaobing Tang

Theses and Dissertations--Chemical and Materials Engineering

Colloidal semiconductor quantum dots (QDs), also called as nanocrystals (NCs), are a class of functional materials with extraordinary properties, which are different from their bulk counterparts and benefit from their exclusive quantum confinement (size) effect. Semiconductor exhibits the quantum confinement effect when the characteristic size of the semiconductor is comparable to or smaller than the de Broglie wavelength of the electron wave function and/or the exciton Bohr diameter of the bulk semiconductor. In recent years, metal halide perovskite NCs, as next-generation semiconductor materials for lighting and display, have aroused a wide attention due to their excellent optoelectronic properties. However, traditional …

Laptop Recycling Case Study: Estimating The Contained Value And Value Recovery Process Feasibility Of End-Of-Life Consumer Electronics, Zebulon Hart

Theses and Dissertations--Mining Engineering

Work has been done to establish, through the development and use of novel assay techniques and analysis metrics, the contained value of a sampling of laptop computers (as an analog for myriad e-waste sources). This work has conceptualized e-waste as an alternative to geologic-origin complex metallic ores and has likewise evaluated the feasibility of value recovery from e-waste sources in a similar manner to an ore. The application of conventional and novel mineral separation techniques to e-waste recycling processes has been evaluated and positive results are demonstrated. Further, this work has demonstrated the ability to identify the presence of base …

Designing The Electrochemical Interface To Enable Lithium Metal Batteries, Supriya Koul

Electronic Theses and Dissertations, 2020-2023

Although Li-ion battery is one of the most widely used energy storage devices, there have been extensive efforts to push its limit to meet the ever-increasing demands to improve its energy density for applications such as electric vehicles, portable electronics, and grid storages. Here, Li metal anode plays a key role in the next generation energy storage devices, ultimately enabling the anode-free configuration. However, there are major challenges that need to be overcome for a successful deployment of anode-free batteries. These include designing a competitive SEI, low Coulombic efficiency, and the formation of dendrites. To realize an effective anode-free configuration …

Additive Manufacturing Of Continuous Carbon Fiber-Reinforced Sic Ceramic Composite With Multiple Fiber Bundles By An Extrusion-Based Technique, Ruoyu Chen, Adam Bratten, Joshua Rittenhouse, Ming-Chuan Leu, Haiming Wen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Due to the high cost, complex preparation process and difficulty in structural design, the traditional methods for carbon fiber reinforced SiC ceramic composite preparation have great limitations. This paper presents a technique for the additive manufacturing multiple continuous carbon fiber bundle-reinforced SiC ceramic composite with core-shell structure using an extrusion-based technique. A conventional nozzle system was modified to print simultaneously a water based SiC paste with continuous carbon fibers. Different levels of binder contents were investigated to optimize the stickiness, viscosity, thixotropy and viscoelasticity of the paste. After sintering, SiC whiskers were generated on the surface of fiber, which is …

Mechanical Property Evaluation Of Additively Manufactured Materials Across A Wide Temperature Range, Sanket Vinayak Hirve

Electronic Theses and Dissertations

Additive manufacturing (also called 3d printing) has transitioned from a prototyping-only technology to a technology that is able to create usable parts with complex geometries. 3D printed parts are beginning to be used across all areas of engineering, such as biomedical, aerospace, automobile and many more. Typically, the term “3D printing” refers to layer by layer deposition of polymer materials, while the term “additive manufacturing” refers to layer by layer metal deposition. Conventional manufacturing, or substrative manufacturing, has several main problems that additive manufacturing can help overcome, such as high cost for low volume production, inability to create very complex …

Mechanical Behavior Of Plain Weave Nylon Reinforced Drop-Stitch Inflatable Panels, Anthony J. White

Open Access Master's Theses

All CUI (Controlled Unclassified Information) is U.S. government property and has been removed from this thesis.

Mechanical Response Of Constituent Materials Used In Plain Weave Nylon Reinforced Inflatable Drop Stitch Structures, Matthew S. Buglio

Open Access Master's Theses

All CUI (Controlled Unclassified Information) is U.S. government property and has been removed from this thesis.

The Effect Of Heat Transfer On Microstructural Development For Inconel718 Nickel-Based Superalloy In Laser Powder Bed Fusion, Erica Drobner

Electronic Theses and Dissertations, 2020-2023

Inconel 718 (IN718) is a superalloy with excellent corrosion resistance and high temperature stability, giving rise to its popular use in the aerospace industry as well as other high performing applications. This study utilizes the relatively low conductivity of IN718 to focus in on the heat transfer procedures in which occur during the laser powder bed fusion (LPBF) manufacturing process of metals. Cylindrical samples of constant geometry with varying dimensions of thermal supports were fabricated using a compatible IN718 build plate. As thermal support size increased, heat dissipation to the build plate consequently increased. Theoretically, this modification of heat transfer …

Controlling The Thermal And Electrical Properties Of Camno3-Δ Based Perovskite Ceramics, Sergio Andres Paredes Navia

Graduate Theses, Dissertations, and Problem Reports (ETD)

Most of the energy lost during the conversion process comes in the form of waste heat. The world's energy consumption loses over 60% of its energy after conversion. In order to increase the efficiency of the conversion process, it is essential to harness waste heat and reutilize this energy resource. Heat recovery technology as thermoelectric (TE) technology is one of the growing alternatives to harvest excessive amounts of energy lost as waste heat for a more efficient, safe, and sustainable future. Due to the Seebeck effect, TE materials have the potential to convert waste heat directly into electricity, improving efficiency …

An Archimedes' Screw For Light, Emanuele Galiffi, Paloma A. Huidobro, J. B. Pendry

Advanced Science Research Center

An Archimedes’ Screw captures water, feeding energy into it by lifting it to a higher level. We introduce the first instance of an optical Archimedes’ Screw, and demonstrate how this system is capable of capturing light, dragging it and amplifying it. We unveil new exact analytic solutions to Maxwell’s Equations for a wide family of chiral space-time media, and show their potential to achieve chirally selective amplification within widely tunable parity-time-broken phases. Our work, which may be readily implemented via pump-probe experiments with circularly polarized beams, opens a new direction in the physics of time-varying media by merging the rising …

Austenitic, Duplex, And Lean Duplex Stainless Steel Critical Pitting Temperature In Simulated Concrete Environment, Bobby Giebel

Williams Honors College, Honors Research Projects

In this work, the critical pitting temperature (CPT) will be observed for a selection of austenitic (316LN and 24100) and duplex (2205), and lean duplex (2304, 2001) stainless steels in simulated concrete pore solution. To study the influence of temperature on the pitting stability of the stainless steels, three temperatures were tested: 25oC, 45oC, and 65oC for cyclic potentiodynamic polarization (CPP) and electrochemical impedance spectroscopy (EIS). Electrochemical properties of the interfaces we studied via EIS analysis. Kinetics were studied via CPP testing. To reveal the critical pitting temperature of the stainless steels, cyclic thermammetry was used. Characterization of the pits …

Additive Manufacturing Waste Management System - Plastic Extrusion Process, Gabriel Bennett, Lindsay Liebrecht, David Lyogky, Wilson Woods

Williams Honors College, Honors Research Projects

3D printing is a fast-growing market with its main source of waste being PLA and ABS plastics. In 2019, the global additive manufacturing market grew to over $10.4 billion, crossing the pivotal double-digit billion threshold for the first time in its nearly 40-year history. (SmarTech Analysis, 2020 Additive Manufacturing Market Outlook and Summary of Opportunities Report). The waste is generated from failed prints and rejected support structures which are common occurrences for personal use. Plastic recycling has become one of the leading discussions of environmental protection and waste management. The 3D market currently does not offer an effective and affordable …

Cathodic Protection, Michaela Schaber

Williams Honors College, Honors Research Projects

This Honors Research Project explores cathodic protection of reinforcing steel in concrete. It uses NACE SP0408-201 Cathodic Protection of Reinforcing Steel in Buried or Submerged Concrete Structures as the guidelines for experiments and supporting literature. An economic analysis will be included to fulfill Design requirements. Different voltage and other applications will be explored to determine the lowest obtainable cost-efficient corrosion rate. The method of cathodic protection focused on for this project is impressed current cathodic protection.

Analysis And Comparison Of Nir Pigments For "Cool" Coating Applications, Karey Steinmetz

Williams Honors College, Honors Research Projects

The goal of this research is to compare our own formulation of near infrared radiation (NIR) pigment coating to commercialized ones. These near infrared coatings are designed to be used on roofs of buildings to keep the buildings from absorbing the heat from the sun’s radiation. This would keep the building cooler and use less energy and money to cool the building. In this study, Styrofoam was used to build a lab-scale house and were put under heat lamps that mimicked the sun. Temperatures were taken at three different locations to determine the effectiveness of the pigmented coatings. Color and …

Adjust-A-Ramp, Taylor Sharrits, Courtney Banks, Emily Beck, Jazmin Buenrostro

Williams Honors College, Honors Research Projects

Adjust-A-Ramp is a portable ramp designed to ensure the safety of consumers and prevention of damage to cars, specifically towards low profile cars. A low-profile vehicle includes any vehicle that has a clearance off the ground of 6.5 inches or less. Advantages of low-profile vehicles include improved handling, better braking, increased fuel efficiency, increased stability, and an overall luxury aesthetic. The reduced tire size increases grip on smooth surfaces with better wheel response, creating a fast, more efficient ride. The simple tire tread patterns and the stiff sidewalls allow for lower rolling resistance which increases fuel economy. The Adjust-A-Ramp can …

Recycled Printer Filament, Charlotte Hyland, Troy D. Molinar

Williams Honors College, Honors Research Projects

The purpose of this research is to examine the effects of recycling PLA filament for 3D printing on its material properties. After examining these effects, PLA and carbon fiber additives were mixed with recycled PLA pellets in different ratios to attempt to regain material properties lost in the recycling process. To complete these findings, an experiment was design and executed.

The research found that tensile strength during multiple iterations of recycling remained mostly unaffected, however, the strain degraded exponentially. In the PLA additive study, high ratios of PLA additive were able to increase the strength and strain properties of the …