Materials Science and Engineering Commons^™

Comparison Of Chinese ， Ame Rican， And Bangladeshi Criteria For Liquefaction Judgment O F Fine‑Grained Soil, Wu Zi

Journal of China & Foreign Highway

The criteria for liquefaction judgment of fi ne-grained soil in current seismic design codes of China，the United States，and Bangladesh are quite different.In order to propose the judgment criteria for engineering application and Chinese code revision，this paper compared the judgment processes and criteria of the three countries.After analyzing the formation process，based on the application of the criteria for liquefaction judgment of 168 fine-grained soil samples collected in Dhaka，Bangladesh and surrounding cities，the rationality of each judgment process and criteria was evaluated comprehensively.Finally，a set of judgment processes and result criteria for fine-grained soil liquefaction integrating all criteria were put forward.

Pyrolysis Kinetics Of Spirulina Platensis And Non-Condensable Gas Product Distribution In A Fixed-Bed Reactor, Ahmad Yusril Aminullah, Sukarni Sukarni, Retno Wulandari, Muhammad Shahbaz

Journal of Mechanical Engineering Science and Technology (JMEST)

Energy is a fundamental factor for civilization development and sustainability. However, energy sources are dominated by non-renewable fractions, such as fossil fuels. Renewable biomass is projected to be a future fuel source. Spirulina platensis (SP) has numerous advantages compared to other biomass, and it is considered 3rd generation biomass that does not interfere with food and land usage and has a relatively low main decomposition temperature at 325.7℃. Thermogravimetric analysis (TGA) was conducted to observe SP kinetics parameters, especially activation energy. Kissinger-Akahira-Sunose (KAS), Ozawa-Flynn-Wall (OFW), and Starink iso-conversional methods reveal that SP has an activation energy of 152.33, 154.56, and …

Simulation Of The Performance Of Kevlar Impregnated Shear Thickening Fluid Ballistic Test Results, Ridwan Prasetya, Andoko Andoko, Suprayitno Suprayitno

Journal of Mechanical Engineering Science and Technology (JMEST)

This study explores the enhancement of Kevlar fabric’s ballistic performance through impregnation with Shear Thickening Fluid (STF) for potential application in soft body armor. The experimental approach often fails to elucidate mechanical phenomena critical for the development of lightweight and high-strength body armor designs. To address this limitation, the finite element method, specifically using ANSYS/LS-DYNA R.13, was employed for a comprehensive analysis. The simulation aimed to evaluate the impact of STF on Kevlar fabric by assessing projectile velocity, force exerted by the projectile onto the fabric, displacement, stress distribution, and fabric failure mechanisms. Kevlar yarn was modeled as a shell …

Fabrication And Characterization Of A Monolithic Photonic Integrated Circuit With High-Aspect Ratio Photonic Device Structures, Sami A. Nazib

Optical Science and Engineering ETDs

The focus of this work was to create a process to fabricate an InP-based Photonic Integrated Circuit (PIC). The design of the PIC required the photonic components of this device to be created by deep etching of an epitaxially-grown multilayer structure. Therefore, a novel dry etching process was developed to produce very high aspect- ratio (HAR) features. This process not only involved the development of dry etch chemistry but also the engineering of a metal mask structure. The next step of the challenge was to use a polymer-based material that would have two functions: cladding for the etched photonic components …

Secondary Electron Yield Of Metals, Alloys, And Metal Oxides From First Principles Based Monte Carlo Simulations, Raul E. Gutierrez

Electrical and Computer Engineering ETDs

Density Functional Theory (DFT) based Monte Carlo (MC) simulations of the Sec-
ondary Electron Yield (SEY) of metals, alloys, and metal oxides are performed to
find material properties that could help reduce or influence the multipactor effect.
In order to accurately model the SEY of materials, knowledge of the frequency- and
momentum-dependent Energy Loss Function (qDepELF) is required. The qDepELF
is difficult to determine from experiment; however, it can be calculated from first
principles. The DFT-MC approach for simulating the secondary electron genera-
tion, propagation, and emission processes is described herein. Material properties,
which are calculated using DFT and used …

Tension–Compression Fatigue Of A Hybrid Polymer-Matrix/Ceramic-Matrix Composite At Elevated Temperature, Marina B. Ruggles-Wrenn, Joshua Schmidt

Faculty Publications

Fully reversed tension–compression fatigue of a hybrid material comprising polymer matrix composite (PMC) co-cured with a ceramic matrix composite (CMC) was investigated. The PMC portion had a polyimide matrix reinforced with 15 plies of carbon fibers woven in an eight-harness satin weave (8HSW). The CMC portion had three plies of a quartz-fiber 8HSW fabric in a zirconia-based ceramic matrix. The hybrid PMC/CMC was developed for use in aerospace thermal protection systems (TPS). Hence, the experimental setup aimed to simulate the TPS service environment—the CMC side was kept at 329 °C, whereas the PMC side was open to laboratory air. Compression …

Series Reports From Professor Wei’S Group Of Chongqing University: Advancements In Electrochemical Energy Conversions (1/4): Report 1: High-Performance Oxygen Reduction Catalysts For Fuel Cells, Fa-Dong Chen, Zhuo-Yang Xie, Meng-Ting Li, Si-Guo Chen, Wei Ding, Li Li, Jing Li, Zi-Dong Wei

Journal of Electrochemistry

Two major challenges, high cost and short lifespan, have been hindering the commercialization process of low-temperature fuel cells. Professor Wei’s group has been focusing on decreasing cathode Pt loadings without losses of activity and durability, and their research advances in this area over the past three decades are briefly reviewed herein. Regarding the Pt-based catalysts and the low Pt usage, they have firstly tried to clarify the degradation mechanism of Pt/C catalysts, and then demonstrated that the activity and stability could be improved by three strategies: regulating the nanostructures of the active sites, enhancing the effects of support materials, and …

Kai Wu, The Editorial Board Member Of Journal Of Electrochemistry And Chief Scientist Of Catl, Receives The National Science And Technology Progress Award, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Sorbitol-Electrolyte-Additive Based Reversible Zinc Electrochemistry, Qiong Sun, Hai-Hui Du, Tian-Jiang Sun, Dian-Tao Li, Min Cheng, Jing Liang, Hai-Xia Li, Zhan-Liang Tao

Journal of Electrochemistry

The unstable zinc (Zn)/electrolyte interfaces formed by undesired dendrites and parasitic side reactions greatly hinder the development of aqueous zinc ion batteries. Herein, the hydroxy-rich sorbitol was used as an additive to reshape the solvation structure and modulate the interface chemistry. The strong interactions among sorbitol and both water molecules and Zn electrode can reduce the free water activity, optimize the solvation shell of water and Zn²⁺ ions, and regulate the formation of local water (H₂O)-poor environment on the surface of Zn electrode, which effectively inhibit the decomposition of water molecules, and thus, achieve the thermodynamically stable …

First Announcement Of 76th Annual Meeting Of The International Society Of Electrochemistry, International Society Of Electrochemistry (Ise)

Journal of Electrochemistry

No abstract provided.

Data-Driven Viewpoint For Developing Next-Generation Mg-Ion Solid-State Electrolytes, Fang-Ling Yang, Ryuhei Sato, Eric Jian-Feng Cheng, Kazuaki Kisu, Qian Wang, Xue Jia, Shin-Ichi Orimo, Hao Li

Journal of Electrochemistry

Magnesium (Mg) is a promising alternative to lithium (Li) in solid-state batteries due to its abundance and high theoretical volumetric capacity. However, the sluggish Mg-ion conduction in the lattice of solid-state electrolytes (SSEs) is one of the key challenges that hamper the development of Mg-ion solid-state batteries. Though various Mg-ion SSEs have been reported in recent years, key insights are hard to be derived from a single literature report. Besides, the structure-performance relationships of Mg-ion SSEs need to be further unraveled to provide a more precise design guideline for SSEs. In this Viewpoints article, we analyze the structural characteristics of …

Professor Yong Yang, The Editorial Board Member Of Journal Of Electrochemistry, Is Elected As A Fellow Of The Electrochemical Society, Editorial Office Of J.Electrochem.

Journal of Electrochemistry

No abstract provided.

Modeling Powder Spreadability In Powder-Based Processes Using The Discrete Element Method, Austin T. Sutton, M. Hossein Sehhat, Ming C. Leu, Joseph W. Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Powder-bed fusion (PBF) processes refer to a subset of Additive Manufacturing (AM) techniques where powder is spread on the build-plate before melting (by a laser or electron beam). While PBF processes are attractive due to their ability for realizing complex structures that are either difficult or impossible to create through conventional means, the parts fabricated with these techniques can exhibit defects such as pores, inclusions, and excessive surface roughness. To minimize these defects, much research has been dedicated towards process maturation by optimizing laser or electron beam parameters. However, these developmental efforts typically do not address the recoating process where …

Assessment Of Wafer Scale Mos2 Atomic Layers Grown By Metal–Organic Chemical Vapor Deposition Using Organo-Metal, Organo-Sulfide, And H2S Precursors, Michael Curtis, Olivia Moryan, Nicholas Mckibben, Josh Eixenberger, Chen Chen, Karthik Chinnathambi, Sergej Pasko, Salim El Kazzi, Joan M. Redwing, David Estrada

Materials Science and Engineering Faculty Publications and Presentations

Transition Metal Dichalcogenides (TMDs) are a unique class of materials that exhibit attractive electrical and optical properties which have generated significant interest for applications in microelectronics, optoelectronics, energy storage, and sensing. Considering the potential of these materials to impact such applications, it is crucial to develop a reliable and scalable synthesis process that is compatible with modern industrial manufacturing methods. Metal–organic chemical vapor deposition (MOCVD) offers an ideal solution to produce TMDs, due to its compatibility with large-scale production, precise layer control, and high material purity. Optimization of MOCVD protocols is necessary for effective TMD synthesis and integration into mainstream …

Developing And Testing Low-Cost Air Cleaners For Safer Spaces During Wildfires, Brett W. Stinson, Elliott T. Gall

Mechanical and Materials Engineering Faculty Publications and Presentations

Air cleaning reduces indoor exposure to fine particulate matter (PM2.5) during wildfire smoke events. However, resource and cost constraints may limit access to air cleaning during such an event, as both commercial devices and the higher-rated MERV filters that do-it-yourself (DIY) assemblies typically rely upon tend to be expensive and in short supply. With these constraints in mind, we developed and evaluated several configurations of a novel, DIY air cleaner that uses common household fabrics as filtration media. Clean air delivery rates (CADRs) of the devices were experimentally evaluated in two ways: first, with independent measurements of flowrates and single …

Annual Progress In Global Carbon Capture, Utilization, And Storage In 2023, Siyuan Fang, Yun Hang Hu

Michigan Tech Publications

Since the industrial revolution, global anthropogenic CO2 emissions have surged dramatically to unsustainable levels, resulting in severe issues, such as global warming, extreme weather events, and species extinction. In response to this critical situation, extensive efforts have been undertaken across academia, industry, and policymaking sectors to deploy carbon capture, utilization, and storage (CCUS) technologies. Here, we present the annual summary of global CCUS for the year 2023. We begin by discussing the trends of anthropogenic CO2 emissions and atmospheric CO2 concentrations, and then offer an up-to-date summary of progress in academia, industry, and policy, respectively. In academia, we analyze the …

The Role Of Furan Moieties On The Thermal Decomposition And Char Formation Of Intrinsically Fire-Resistant Epoxy Thermosets For Composites, Amy E. Honnig Bassett

Theses and Dissertations

Fire-retardant chemicals added to epoxy thermosets used as coatings, adhesives, and fiber-reinforced polymer composites (FRPCs) negatively impact performance and the environment. This dissertation takes a novel approach to mitigate the flammability of these systems by designing intrinsically fire-resistant epoxies via the incorporation of furan moieties. Glycidyl amines based on furfuryl amine and judiciously selected derivatives of furfuryl amine were synthesized to produce furan-based di-epoxies (FDEs) that were cured by anionic polymerization and with amine curing agents. The furan ring was found to impart additional reactivity for cross-linking and to induce char-forming reactions at higher temperatures. More importantly, the placement of …

Experimental Investigation On Mechanical Properties Of Pla Reinforced By Bamboo Fiber/Montmorillonite Clay Hybrid Composites And Analysis Of Machining Characteristics, Nirmal Kumar K

Theses and Dissertations

The study presents a comprehensive investigation into the development, characterization, and machining analysis of novel bio-based polymer hybrid composites comprising Polylactic acid (PLA), bamboo powders (BP), and montmorillonite clay particles (MMT). Initially, the hybrid composites were fabricated using a solvent-free stir casting process, optimizing the weight percentages of BP and MMT to enhance mechanical and thermal properties.

Mechanical tests, including tensile, flexural, and impact tests, along with thermal analysis using thermogravimetric analysis and differential scanning calorimetry, were conducted to evaluate the performance of the composites. In the subsequent phases, advanced machining techniques were employed to analyze the machining characteristics of …

Optical Responses Of Hybrid Electromagnetic Nanostructures, Dominic Bosomtwi

Optical Science and Engineering ETDs

Fano resonances result from the interference between a broad background and a narrow state, producing asymmetric scattering profiles. Under specific conditions, destructive interference collapses the Fano resonance width, leading to bound states in the continuum (BICs) that localize light within a nanostructure while maintaining an infinitely high-quality factor (Q-factor).

This dissertation explores the design of nanostructures with multilayer hybrid plasmonic-dielectric metasurfaces using full-wave numerical simulations, facilitating multiple Fano resonances and BICs. By adjusting nanoantenna dimensions, multiple modes are excited at plasmonic-dielectric interfaces, leading to strong interactions and hybridization of energy levels, manifested as Rabi splitting.

These findings enable advancements in …

Article Comprising Bonded Substrate Comprising Nanocrystals And Method Of Making And Using Same, Michael D. Sherburne

AFIT Patents

The present invention relates to devices for measuring property changes via in-situ micro-viscometry and methods of using same. The aforementioned device is inexpensive and can be used to quickly and accurately measure numerous physical and chemical property changes, including but not limited to the rate of chemical cure, change in tack, and rate of mass loss, for example, rate of moisture, solvent and/or plasticizer change.