Metallurgy Commons^™

Structural And Photoluminescence Properties Of Zno Thin Films Deposited By Ultrasonic Spray Pyrolysis, Iwan Sugihartono, Erfan Handoko, Vivi Fauzia, Artoto Arkundato, Lara Permata Sari

Makara Journal of Technology

Zinc oxide (ZnO) thin films on a silicon (Si) (111) substrate were grown herein using ultrasonic spray pyrolysis at 450 °C with different Zn concentrations. The ZnO thin films had X-ray diffraction patterns of a polycrystalline hexagonal wurtzite structure. The (002) and (101) peak intensities changed under different Zn concentrations. Furthermore, according to Scherer's and Stokes–Wilson equations, the crystallite size and the internal strain of the ZnO thin films in the (002) and (101) peaks changed with the Zn concentration. Optically, the photoluminescence spectra indicated that the ratio of the UV/GB emission of the ZnO thin films was the highest …

An Exploratory Study Of Sukuk Utilisation For Transportation Infrastructure Development In Indonesia, Fiona Lamari, Ayomi Dita Rarasati, Meilia Evita

Makara Journal of Technology

Investment in infrastructure is one of the principal drivers of the growth of the economy. For that reason, the Indonesian government has proposed an investment budget in the railway and sea and air transport sectors over the next 10 years. In order to overcome the burden of direct outflows and for the future, a study was conducted to lay down the framework of Shariah-compliant payments for the development of infrastructure in Indonesia in the transport sector. This paper aims to explore the opportunity and implementation of sukuk utilisation to develop transportation infrastructure. Secondary data study and interviews were selected for …

Characterization Of Process Induced Defects In Laser Powder Bed Fusion Processed Alsi10mg Alloy, Edward Stugelmayer

Graduate Theses & Non-Theses

Additive manufacturing using laser powder bed fusion (AM-LPBF) methods have recently experienced rapid growth and development, having the potential to replace manufacturing by plastic deformation, precision machining, or casting. AM offers advantages such as the freedom to design highly complex geometries, time and cost savings through material usage efficiency and shortened production cycles, and the potential for improved mechanical properties. Process induced defects, however, result in degradation and scattering of mechanical properties and hinder the widespread adoption of AM-LPBF in industry. This investigation focuses on the effects of varying energy density and build orientation on the evolution of process induced …

Investigations Of Solid-State Sintering Behavior Of Binary Refractory Metal Oxide Systems, Maureen Chorney

Graduate Theses & Non-Theses

Refractory metals are commonly alloyed for improved corrosion resistance, thermal stability, and strength. In service, these alloys form highly stable oxides under mildly oxidizing conditions at relatively low temperatures. In order to recycle these materials, high temperature electrochemical processing is required to reduce the refractory metal oxides. To abet experimental evaluation of the electrochemical reduction process under development at the Idaho National Laboratory, binary mixtures of selected refractory metal oxide powders were sintered to produce cathode pellets, which could be suspended in the molten salt electrolyte during reduction experiments. Preparatory literature review revealed a paucity of published information relative to …

Seismic Response Analysis Along The Coastal Area Of Bengkulu During The September 2007 Earthquake, Lindung Zalbuin Mase

Makara Journal of Technology

A strong earthquake of 8.4 Mw occurred at the Sumatra Subduction Zone in September 12, 2007. The area that underwent the impact of the earthquake was located along the coastal area of the Bengkulu Province. A seismic ground response study was then performed with reference to the event. Several site investigations, including standard penetration test and shear wave velocity tests, were conducted to understand the subsoil condition. The data were used to analyze a ground response during the earthquake. The amplification factor of each site was obtained, and a comparison of the spectral accelerations was performed. The results showed that …

Coax-Fed Dipole-Type Applicator For Hepatic Cancer Rf Ablation, Basari Basari, Aditya Rakhmadi, Kazuyuki Saito

Makara Journal of Technology

Cancer is the third leading cause of mortality in the world and is one of the most difficult diseases to detect and cure. This fact motivates us to investigate a treatment method by using radiofrequency (RF) ablation. RF ablation therapy kills cancer cells by electromagnetically heating them up. The treatment uses an applicator that is inserted into the body to heat the cells. The cancer cells are exposed to a temperature of more than 60 °C in short duration (a few seconds to a few minutes), thereby causing cell destruction locally. To ensure effective treatment, a minimally invasive method is …

Nanostructural Origin Of Semiconductivity And Large Magnetoresistance In Epitaxial Nico2O4/Al2O3 Thin Films, Congmian Zhen, Xiaozhe Zhang, Wengang Wei, Wenzhe Guo, Ankit Pant, Xiaoshan Xu, Jian Shen, Li Ma, Denglu Hou

Xiaoshan Xu Papers

Despite low resistivity (~1 mΩ cm), metallic electrical transport has not been commonly observed in inverse spinel NiCo₂O₄, except in certain epitaxial thin films. Previous studies have stressed the effect of valence mixing and the degree of spinel inversion on the electrical conduction of NiCo₂O₄ films. In this work, we studied the effect of nanostructural disorder by comparing the NiCo₂O₄ epitaxial films grown on MgAl₂O₄ (1 1 1) and on Al₂O₃ (0 0 1) substrates. Although the optimal growth conditions are similar for the …

Micro-Slotting Technique For Measurement Of Local Residual Stress In Metallic Materials, Elizabeth Anne Burns

Doctoral Dissertations

"Micro-slotting, a micro-scale relaxation residual stress measurement technique, has been shown in recent years to be a reliable method for measuring local residual stresses in metallic materials. This technique employs an SEM-focused ion beam system for milling and imaging, digital image correlation software to track displacements due to residual stress relaxation, and finite element analysis for interpolation of the original local stress state. In this research, a micro-slotting procedure was established using finite element models and was used to obtain sub-surface residual stress measurements on machined and shot peened planar Ti-6Al-4V samples. These measurements were compared to macro-scale XRD residual …

Chemistry, Design, And Processing Of Two-Stage Trip Steel, Daniel M. Field

Doctoral Dissertations

"A regular solution model was developed to calculate the chemical driving force for α-martensite formation, ΔG^{λ→ α}_Chem. A model for the strain energy, ΔG^λ→α_str, was formulated utilizing the Young’s modulus (E), lattice misfit squared (δ²), and molar volume (Ω) which opposed the chemical driving force for α-martensite formation. The M^α_S was determined at a temperature at which ΔG^λ→α_Chem + ΔG^λ→α_str = 0. In conjunction with a previously developed ε-martensite model, a means of predicting the volume fraction of λ-austenite was determined; and it was shown that for values …

Direct Strength Approach To Predict The Flexural Strength Of Cold-Formed Z-Section Purlins On Sloped Roofs, Ali Parva, Michael W. Seek

Engineering Technology Faculty Publications

In this study, the strength of cold-formed Z-section purlins is predicted considering the effects of roof slope in real roof systems. The study applies to simple span purlins with torsion restraints at support locations and at paired locations along the length of the member. A previously developed method has shown through comparisons to base tests that when the biaxial bending and torsion stresses are incorporated into the analysis, the Direct Strength Method can accurately predict the strength of a purlin. These stress distributions can deviate substantially from the constrained bending approximation typically assumed in analysis and therefore impacts the local …

Corrosion Performance Of Zirconium-Based Passivations On Electroplated Zinc Nickel, Madison Morgan Reed

Masters Theses

“Performance requirements for Department of Defense (DoD) electrical components include corrosion and electrical contact resistance. Historically, electroplated cadmium with a chromate conversion coating (CrCC) has been used to meet corrosion and contact resistance standards. However, replacements are needed for these materials because they are toxic and carcinogenic. Electroplated γ-ZnNi has been identified as an acceptable alternative to Cd. This study evaluated commercially available Zr-based thin films and sealers as passivations for potential replacement of CrCCs. Ten different passivations were tested and compared with bare γ-ZnNi. X-Bond and Zircobond passivations were found to provide some improvement to the bare ZnNi corrosion …

Grain Refinement Of High Alloy Stainless Steels In Sand And Directionally Solidified Castings, Dustin Alan Arvola

Masters Theses

"The goal of this research project is to develop an industrially viable melting process that will control the crystallization macrostructure of austenitic grades of cast steels. Titanium nitride (TiN) has proven to be an effective grain refiner of austenite. Theoretical simulation and experimental application has led to the development of a repeatable grain refining melt process for austenitic stainless steel alloys.

Grain refinement of the as-cast structure of Cr-Ni stainless steel alloys solidified with primary FCC, BCC and dual FCC/BCC phases was studied experimentally. Refinement was achieved in both cast ferritic and austenitic grades. Dual solidification of …

Effect Of Microstructural Features On Steel Machinability, Mark C. Emmendorfer

Masters Theses

Non-metallic inclusions can have a tremendous impact on the machinability of steel. Some oxide inclusions such as alumina, spinel, and other refractory abrasive oxide inclusions can have a detrimental effect on machinability. Modification of oxide inclusions by calcium treatment can promote the formation of low melting point oxides such as anorthite and gehlenite inclusions that can assist in chip formation and form a lubricating layer on the rake surface of the machine tool. MnS is known to be beneficial to improving the machinability of steel. They assist in chip formation by being heavily deformed in the primary shear zone. Sulfide …

Measurement Of Planar Fault Probabilities In Austempered Ductile Iron And 304l Stainless Steel, Nathan Peterson

Dissertations, Master's Theses and Master's Reports

During plastic deformation both stacking and twin faults can be generated in face-centered cubic materials, including iron-based metals that contain thermally stable austenite. These planar faults are a critical component of the austenite to martensite transformation, forming shear bands that can act as nucleation sites. The measurement of these faults via x-ray diffraction has been long established, however it has not been applied widely to austempered ductile irons. The ability to measure these faulting probabilities could give insights into the transformation as a function of deformation. In this work both planar fault densities were measured in austempered ductile iron to …

Atomic Probe Tomography And Creep Deformation Studies Of Highly Dynamic Metallic Systems: Copper-Zirconium Based Metallic Glass Alloys And Tin-Based Alloy, Chetarpa Yipyintum

Chulalongkorn University Theses and Dissertations (Chula ETD)

The early crystallization process of a Cu-Zr binary metallic glass was investigated by transmission electron microscopy (TEM) and atomic probe tomography (APT). The microstructural analysis was carried out using different characterization methods to see if the phase separation in different chemical compositions and chemical short-range orders were investigated by applying heat treatment under argon atmosphere in differential scanning calorimetry (DSC) chamber. Such a difference in the atomic arrangement of a given amorphous metallic structure is important, the actual characterization of such small difference is not practically easy. For the reason that there is an effect of the sample preparation method …

Effects And Limitations Of Residual Alloying Elements In Silicon Solid Solution Strengthened Ferritic Ductile Iron, Julia Scruton

Dissertations, Master's Theses and Master's Reports

Transitioning from traditional grades of ductile iron to solution strengthened ferritic ductile iron (SSFDI) grades can be difficult because of the need to reduce the amount of pearlite promoting elements, particularly copper and manganese, which are used in traditional grades. Knowing the acceptable threshold of residual alloying elements will allow for more cost-effective tailoring of the charge stream. Data were generated from a series of casting trials with the target grade of EN-GJS-500-14 where the levels of copper and manganese were varied from 0.05% to 0.3% and 0.15% to 0.4% respectively while maintaining silicon in the 3.8%-4.3% range. The pearlite …

Induced Ferromagnetism In Multilayered Graphene In Proximity With Cofe2o4, Himanshu Verma, Dereje Seifu, Shashi P. Karna, Haiping Hong, Mohindar S. Seehra

Faculty & Staff Scholarship

Composites of anisotropic diamagnetic multilayer Graphene (MLG) and ferrimagnetic CoFe2O4 (CFO) nanoparticles (NPs) were synthesized through a one-step sonication process in the presence of a surfactant. The samples were characterized at ambi- ent using x-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), Raman spectroscopy, magnetic force microscopy (MFM) and magnetometry (vibrating sample magnetometer). An induced ferromagnetism was observed in MLG with saturation magnetization MS = 18 emu/g(MLG). This induced ferromagnetism is attributed to ferrimagnetic CFO uniformly distributed on the surface of diamagnetic MLG. SEM images confirm uniform dense distribu- tion of CFO nanoparticles on MLG. MFM images …

Interfacial Corrosion Of Copper And The Formation Of Copper Hydroxychloride, Mary Teague, Shengxi Li, Hongbo Cong

Williams Honors College, Honors Research Projects

Electrical circuitry is an industry, among many others, heavily using the element of copper. Ensuring the mechanical integrity of Cu is crucial, especially in salt environments, for the multifaceted composition of circuits. 4N NaCl solution (equilibrium concentration in ~84% RH) simulated this three-phase system. Rectangular Cu samples were partially immersed in both ambient and continuous lab air sparging atmospheres to understand waterline corrosion of the metal. Open circuit potentials (OCP) were continuously taken during the immersion testing for a maximum of 5 days. A scanning electron microscopy (SEM) equipped with an energy dispersive X-ray spectrometer (EDS), Raman spectroscopy, and 3-D …

Development Of Oxide-Dispersion-Strengthened Nickel-Based Super Alloy Powders For Additive Manufacturing, Sizhe Huang

Graduate Theses, Dissertations, and Problem Reports (ETD)

Oxide-Dispersion-Strengthened (ODS) Nickel-Based superalloy has been drawn a huge attention and developed with good oxidation resistance, corrosion resistance and high creep strength. It has been considered as critical materials for Additive Manufacturing (AM). The quality and the efficiency of fabrication methods of ODS limits the performance of itself on AM. The development of new type of ODS, new methodologies and evaluation techniques are required if the enhanced quality of ODS and enhanced efficiency of fabrication are to be achieved. Of the current fabrication techniques for AM, Gas Atomization (GA) is widely used since they can generate spherical powders with high …

Effect Of Chromium Content On Heat Treatment Behavior And Abrasive Wear Resistance Of Multi-Alloyed White Cast Iron, Jatupon Opapaiboon

Chulalongkorn University Theses and Dissertations (Chula ETD)

The effect of Cr content on heat treatment behavior and abrasive wear resistance of multi-alloyed white cast irons with basic composition was investigated. The cast irons with varying Cr content from 3-9% were prepared. The annealed specimens were hardened from 1323K and 1373K austenitizing and then, tempered at 673K to 873K with 50K intervals. The microstructure of each specimen consisted of primary austenite dendrite (γP) and (γ+MC) and (γ+M2C) eutectics in specimens with 3 and 5%Cr. By contrast, (γ+M7C3) eutectic appeared in specimens with 6%Cr and more. The matrix in as-cast state was mostly retained austenite but that in as-hardened …