A New Synthesized Microalloys Steel Ods Of High Amplitude Ultrasonically Irradiation,
2019
PSTBM-BATAN, Puspiptek Serpong Area, Tangerang Selatan 15314, Indonesia
A New Synthesized Microalloys Steel Ods Of High Amplitude Ultrasonically Irradiation, Marzuki Silalahi, Hanif Abdurrahman Wicaksana, Ferhat Aziz, Syahfandi Ahda, Mohamad Riza Iskandar
Makara Journal of Technology
Micropowders of oxide-dispersion-strengthened (ODS) steel have been synthesized using the ultrasonic irradiation method with variations in amplitude. The ultrasonic irradiation process is performed for 50 h at a frequency of 20 kHz with 40%, 50%, and 60% amplitudes in toluene solution. The formation of Fe-Cr microalloys in the preparation of Fe- 15Cr-0.5Y2O3 powder was analyzed using SEM-EDS, X-ray diffraction (XRD), and TEM-EDS. The percentage of Fe- Cr phase mass fraction of ODS steel micropowder formed during ultrasonic irradiation with 40%:50%:60% amplitude was 12.2%:34.1%:22.1%, with 25.67:77.02:38.51 nm crystallite size. The crystallite size at 50% amplitude was the largest, and the diffusion …
Study On Antibacterial Of Chitosan/Hydroxyapatite Doped Magnesium Composite As A Material For Bone Graft Applications,
2019
Material and Metallurgical Engineering, Institut Teknologi Kalimantan, Balikpapan 76127, Indonesia
Study On Antibacterial Of Chitosan/Hydroxyapatite Doped Magnesium Composite As A Material For Bone Graft Applications, Andromeda Dwi Laksono, Teodoro A. Amatosa, Jr., Hilda Pebrianti Octaviana Sitorus, Wentika Putri Kusuma Asih, Sulistijono Sulistijono
Makara Journal of Technology
Hydroxyapatite (HAp) is one of the constituent minerals of bone and teeth, that has been widely used for synthesizing bone graft. Due to the limitation on properties of the hydroxyapatite, it is doping with Magnesium (HAp-Mg). The addition of Chitosan (Chi) was expected to improve the antibacterial properties of HAp-Mg. The present research aims to study the influence of Chitosan with 0, 5, 15, and 25 wt% addition on biocompatibility properties of Chi/HAp-Mg composite. HAp-Mg was synthesized using the sol-gel method; meanwhile, Chi/HAp-Mg composite was manufactured by mixing Chitosan in acetic acid, and HAp-Mg was added into the mixture. The …
Evaluation Of Primal-Dual Splitting Algorithm For Mri Reconstruction Using Spatio-Temporal Structure Tensor And L1-2 Norm,
2019
Department of Electrical Engineering, Faculty of Engineering, Universitas Indonesia, Depok 16424, Indonesia
Evaluation Of Primal-Dual Splitting Algorithm For Mri Reconstruction Using Spatio-Temporal Structure Tensor And L1-2 Norm, Mia Rizkinia, Masahiro Okuda
Makara Journal of Technology
Magnetic resonance imaging (MRI) is an essential medical imaging technique which is widely used for medical research and diagnosis. Dynamic MRI provides the observed object visualization through time and results in a spatiotemporal signal. The image sequences often contain redundant information in both spatial and temporal domains. To utilize this characteristic, we propose a spatio-temporal reconstruction approach based on compressive sensing theory. We apply spatio-temporal structure tensor using nuclear norm, in addition to the wavelet sparsity regularization. The spatio-temporal structure tensor is a matrix that consists of gradient components of the MRI data w.r.t the spatial and temporal domains. For …
Acute Toxicitystudy Of Choline Based Ionic Liquids Towards Danio Rerio Fish And The Aggregation Behavior Of Their Binary Mixtures,
2019
Department of Chemical Engineering, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, Perak 32610, Malaysia
Acute Toxicitystudy Of Choline Based Ionic Liquids Towards Danio Rerio Fish And The Aggregation Behavior Of Their Binary Mixtures, Mansoor Ul Hassan Shah, Nasruddin Nasruddin, Suzana Bt Yusup, Muhammad Moniruzzaman
Makara Journal of Technology
Marine oil spills are effectively controlled by chemical dispersants. However, the toxicity associated with it reduce its employment in marine environment. To overcome this limitation, the acute toxicity of choline based ionic liquids was evaluated as a potential low toxic variant for oil spill remediation. Further, the aggregation behavior of the individual as well as their binary mixtures was also evaluated by employing tensiometry technique. The half-lethal concentration, LC50on zebrafish (Danio rerio) of three choline based ionic liquids showed that the studied ionic liquids (ILs) fall in the range of “practically nontoxic” ( 100-1000 mg L-1).Various micellar properties showed that …
Contamination Of Coupling Glass And Performance Evaluation Of Protective System In Vacuum Laser Beam Welding,
2019
Korea Institute of Industrial Technology
Contamination Of Coupling Glass And Performance Evaluation Of Protective System In Vacuum Laser Beam Welding, Yongki Lee, Jason Cheon, Byung-Kwon Min, Cheolhee Kim
Mechanical and Materials Engineering Faculty Publications and Presentations
Vacuum laser beam welding enables deeper penetration depth and welding stability than atmospheric pressure laser welding. However, contaminated coupling glass caused by welding fumes in the vacuum space reduces laser transmittance, leading to inconsistent penetration depth. Therefore, a well-designed protective system is indispensable. Before designing the protective system, the contamination phenomenon was quantified and represented by a contamination index, based on the coupling glass transmittance. The contamination index and penetration depth behavior were determined to be inversely proportional. A cylindrical protective system with a shielding gas supply was proposed and tested. The shielding gas jet provides pressure-driven contaminant suppression and …
Magnetocaloric Effect Near Room Temperature In Quintenary And Sextenary Heusler Alloys,
2019
Central Washington University
Magnetocaloric Effect Near Room Temperature In Quintenary And Sextenary Heusler Alloys, Benjamin D. White, R. I. Barabash, O. M. Barabash, I. Jeon, M. B. Maple
All Faculty Scholarship for the College of the Sciences
An inverse magnetocaloric effect is studied in Ni2Mn1+xX1-x-type Heusler alloys. Principally known for their shape-memory properties, these alloys also exhibit significant entropy and temperature changes (ΔS and ΔTAd, respectively) under adiabatic conditions when a modest magnetic field is applied. We investigated the impact on magnetocaloric properties of introducing substantial chemical disorder on the X-site (X = Si, Ga, In), of replacing Ni with nonmagnetic Ag, and of replacing a small amount of Mn with Gd. While a reduction in ΔS is observed in the first two cases, we observe a significant enhancement …
Investigation Of Surface Treatment And Density Separation For Selective Recycling Of Plastics,
2019
Montana Tech
Investigation Of Surface Treatment And Density Separation For Selective Recycling Of Plastics, Adilbek Baigabelov
Graduate Theses & Non-Theses
Froth flotation has been a useful method for flotation separation of plastics. Teeter bed concentration may also be potentially employed to accomplish gravity-based separation of plastics from a mixture. This work investigates selective separation of six different types of plastics using a novel method by combining advanced gravity concentration and froth flotation techniques. Surface active reagents were used during flotation studies for modification of surface properties of certain plastics in order to enhance selectivity. Elutriation technology in a teeter bed separator was successfully employed to achieve gravity-based concentration of certain plastics. The novel flowsheet was shown to recover plastics of …
Grain Size Effects In Selective Laser Melted Fe-Co-2v,
2019
Missouri University of Science and Technology
Grain Size Effects In Selective Laser Melted Fe-Co-2v, Wesley Everhart, Joseph William Newkirk
Materials Science and Engineering Faculty Research & Creative Works
The material science of additive manufacturing (AM) has become a significant topic due to the unique way in which the material and geometry are created simultaneously. Major areas of research within inorganic materials include traditional structural materials, shape memory alloys, amorphous materials, and some new work in intermetallics. The unique thermal profiles created during selective laser melting (SLM) may provide new opportunities for processing intermetallics to improve mechanical and magnetic performance. A parameter set for the production of Fe-Co-2V material with additive manufacturing is developed and efforts are made to compare the traditional wrought alloy to the AM version of …
Processing Manipulation Of Carbon Content In Cu-34.6%Mn,
2019
Purdue University
Processing Manipulation Of Carbon Content In Cu-34.6%Mn, Samuel Inman
The Journal of Purdue Undergraduate Research
No abstract provided.
Comparison Of Fatigue Performance Between Additively Manufactured And Wrought 304l Stainless Steel Using A Novel Fatigue Test Setup,
2019
Missouri University of Science and Technology
Comparison Of Fatigue Performance Between Additively Manufactured And Wrought 304l Stainless Steel Using A Novel Fatigue Test Setup, M. M. Parvez, Y. Chen, Joseph William Newkirk, Frank W. Liou
Materials Science and Engineering Faculty Research & Creative Works
In this research, a novel adaptive controlled fatigue testing machine was designed for bending type high cycle fatigue test. A unique dual gauge section Krouse type mini specimen was designed for simply supported transverse bending. Displacement controlled fatigue tests were implemented using an electromechanical actuator. The variation in the control signal and load observed during the test provides unique insights into realizing the deterioration of the specimen due to fatigue. These analyses were utilized to compare the fatigue performance of wrought and additively manufactured 304L stainless steel. The influence of the build direction on fatigue performance was also investigated by …
Compressive And Bending Performance Of Selectively Laser Melted Alsi10mg Structures,
2019
Missouri University of Science and Technology
Compressive And Bending Performance Of Selectively Laser Melted Alsi10mg Structures, D. Murphy, O. Fashanu, Myranda Spratt, Joseph William Newkirk, K. Chandrashekhara, H. Misak, D. Klenosky
Materials Science and Engineering Faculty Research & Creative Works
Selective laser melting (SLM) is a widely used additive manufacturing technique that effectively manufactures complex geometries such as cellular structures. However, challenges such as anisotropy and mechanical property variation are commonly found due to process parameters. In a bid to utilize this method for the commercial production of cellular structures, it is important to understand the behavior of a material under different loading conditions. In this work, the behavior of additively manufactured AlSi10Mg under compression, bending, and tension loads was investigated. Vertical and horizontal build directions are compared for each type of loading. Specimens were manufactured using the reduced build …
Effective Elastic Properties Of Additively Manufactured Metallic Lattice Structures: Unit-Cell Modeling,
2019
Missouri University of Science and Technology
Effective Elastic Properties Of Additively Manufactured Metallic Lattice Structures: Unit-Cell Modeling, Okanmisope Fashanu, David Murphy, Myranda Spratt, Joseph William Newkirk, K. Chandrashekhara, Ben Brown, John Porter
Materials Science and Engineering Faculty Research & Creative Works
Lattice structures are lightweight materials, which exhibit a unique combination of properties such as air and water permeability, energy and acoustic absorption, low thermal conductivity, and electrical insulation. In this work, unit-cell homogenization was used to predict the effective elastic moduli of octet-truss (OT) lattice structures manufactured using selective laser melting (SLM). OT structures were manufactured using a Renishaw AM 250 SLM machine with various relative densities. Compression test was carried out at strain rate 5 x 10-3 m-1 using an MTS frame. Finite element analysis was used in the determination of the OT’s effective elastic properties. Results …
Elevated Temperature Mechanical And Microstructural Characterization Of Slm Ss304l,
2019
Missouri University of Science and Technology
Elevated Temperature Mechanical And Microstructural Characterization Of Slm Ss304l, G. R. Hecht, Sriram Praneeth Isanaka, Joseph William Newkirk
Materials Science and Engineering Faculty Research & Creative Works
SLM built SS304L was annealed and water quenched to minimize residual stress and avoid carbide precipitation. Mini-tensile characterization of strength and elongation at temperature conditions up to 800°C, along with observations of the associated microstructural transformations were utilized to understand the changes produced in SLM SS304L. As-built and annealed specimens were found to exhibit decreasing strength and elongation with increasing temperature as expected. Carbide precipitates appeared after short times at high temperatures within both as-built and annealed specimens for all cases, but no brittle intermetallic phase development was observed for any of the temperatures investigated. While the lack of Sigma, …
A Study Of The Electron Regeneration Efficiency Of Solar Cells Fabricated Using Cmc/Pva-, Alginate-, And Xanthan-Based Electrolytes,
2019
Material Technology Program, Faculty of Industrial Sciences & Technology, Universiti Malaysia Pahang, Lebuhraya Tun Razak, Gambang 26300, Kuantan, Pahang, Malaysia
A Study Of The Electron Regeneration Efficiency Of Solar Cells Fabricated Using Cmc/Pva-, Alginate-, And Xanthan-Based Electrolytes, Nur Farha Shaafi, Saifful Kamaluddin Muzakir, Bouchta Sahraoui
Makara Journal of Technology
A photovoltaic (PV) mechanism consists of three important steps, i.e., (i) electron excitation upon absorption of photon with energy higher than the bandgap of fluorophore, (ii) excited-state electron injection from the fluorophore to the pho-toelectrode, and (iii) electron regeneration from the electrolyte to the fluorophore. An efficient electron regeneration could be achieved upon fulfillment of the requirements of energy alignment, i.e., lowest unoccupied molecular orbital of fluorophore (LUMOfluorophore) > redox potential of electrolyte > highest occupied molecular orbital of fluorophore (HOMOfluorophore). This study investigated the electron regeneration efficiency of excitonic solar cells fabricated using three polymer-based electrolytes, i.e., (i) 60% carboxymethyl cellulose …
Study Of Ecological Design Of Residential Complexes Using Spss To Elevate Resident Satisfaction,
2019
Department of Architecture, University of Marlik, Mazandaran 46134, Iran
Study Of Ecological Design Of Residential Complexes Using Spss To Elevate Resident Satisfaction, Soheil Malekpour Kolbadinejad, V. Malekpour Ravasjan, A. Darvish
Makara Journal of Technology
This article reports the general residential satisfaction, affecting ecological factors, and their importance in area in Tehran. The collected field data was analyzed using SPSS. Cronbach's alpha variable was used to determine the reliability of the questionnaire and the Friedman test was used to assess priorities that influence residential satisfaction. The results show that the quality of residential environments and general satisfaction of their residents may be enhanced by identifying these criteria and making appropriate plans for their improvement.
Adsorption Of Heavy Metal Ions By Oil Palm Decanter Cake Activated Carbon,
2019
Department of Bioprocess Technology, Faculty of Biotechnology and Biomolecular Sciences, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor, Malaysia
Adsorption Of Heavy Metal Ions By Oil Palm Decanter Cake Activated Carbon, Mohd. Ezreeza Mohamed Yusoff, Juferi Idris, Nahrul Hayawin Zainal, Mohamad Faizal Ibrahim, Suraini Abd-Aziz
Makara Journal of Technology
Adsorption processes are widely used for the removal of heavy metals from waste streams. Oil palm decanter cake (OPDC) is used as a bioadsorbent because of its compositional properties for activated carbon production; moreover, it is a readily available raw material produced in palm oil mills and is thus abundant and cheap. In this study, the OPDC was carbonized at 700 °C and activated using steam at 700 °C to produce oil palm decanter cake activated carbon (AC-OPDC). Batch adsorption experiments were carried out to compare the adsorption capacities of the raw OPDC and the AC-OPDC for heavy metals removal. …
Use Of The “Dnachecker” Algorithm For Improving Bioinformatics Research,
2019
Department of Bioinformatics, School of Life Sciences, Indonesia International Institute for Life Sciences, Jakarta Timur 13210, Indonesia
Use Of The “Dnachecker” Algorithm For Improving Bioinformatics Research, Nausheen Bhat, Ezra Bernadus Wijaya, Arli Aditya Parikesit
Makara Journal of Technology
Basic Local Alignment Sequencing Tool (BLAST) is a bioinformatics tool used for analyzing nucleotide sequences with regards to their similarity. BLAST can be found online on biological databases such as the National Center for Biotechnology Information (NCBI) and other such repositories. The mechanism of BLAST allows the target sequence to be compared with other sequences to find regions of local similarity, and thus, a comparability quotient that determines the resemblance between the sequences is created. Due to the open-platform nature of the online databanks, several sequences can be accepted with little to no interjections regarding the quality of sequence submitted. …
Component Analysis And Antiangiogenic Activity Of Thailand Stingless Bee Propolis,
2019
Department of Food and Nutritional Sciences, University of Shizuoka, Shizuoka 424-0414, Japan
Component Analysis And Antiangiogenic Activity Of Thailand Stingless Bee Propolis, Eriko Ishizu, Sari Honda, Tosihro Ohta, Boonyadist Vongsak, Shigenori Kumazawa
Makara Journal of Technology
Propolis is a natural resin produced by honey bees from certain plants, has gained popularity as a food and alternative medicine. However, to the best of our knowledge, few studies on native Thailand stingless bee propolis are available. Information on the chemical composition and biological activities of propolis is needed to investigate its potential utility. Recently we have reported the possible plant origin of Thailand stingless bee propolis, Garcinia mangostana. In this study, further component analysis, functional evaluation, and identification of the plant origin of Thailand stingless bee propolis are conducted. Nine xanthones, including α-mangostin, garcinone C, γ-mangostin, cochinchinone T, …
3d Fdtd Method For Modeling Of Seismo-Electromagnetics Disturbance On Crustal Earth,
2019
Faculty of Engineering and Informatics, Universitas Multimedia Nusantara, Tangerang 15811, Indonesia
3d Fdtd Method For Modeling Of Seismo-Electromagnetics Disturbance On Crustal Earth, Nabila Husna Shabrina, Yasuhide Hobara, Achmad Munir
Makara Journal of Technology
The paper deals with the modelling of seismo-electromagnetics disturbance on the crustal earth by use of threedimensional (3D) finite-difference time-domain (FDTD) method. The model is built up by discretizing the frontier geographical region between Java Island and Sumatra Island in a cylindrical coordinate system-based 3D object. The proposed method is applied to compute and analyze electromagnetics (EM) fields of the observed very low frequency (VLF) wave used for the investigation. Boundary condition of uniaxial perfectly matched layer (UPML) are applied surrounding the area of computation for truncating the object of simulation. The investigation are focused on the propagation time of …
Experimental Evaluation Of Three Different Humidity Conditions To Physical And Mechanical Properties Of Three Different Mixtures Of Unfired Soil Bricks,
2019
Civil Engineering Department, Universitas Indonesia, Depok 16424, Indonesia
Experimental Evaluation Of Three Different Humidity Conditions To Physical And Mechanical Properties Of Three Different Mixtures Of Unfired Soil Bricks, Heru Purnomo, Srikandi Wahyu Arini
Makara Journal of Technology
Unfired brick is considered as a more environmentally friendly material than fired brick. It has lower mechanical properties than that of fired brick where humidity influences both bricks. Physical and mechanical properties of unfired bricks made of three kinds of mixtures were studied experimentally under three humidity conditions. The first kind of unfired brick was made only with soil and water while the second type was made of a mixture of soil, water and lime, and the third type was a mixture of soil, water, lime and uniform treated coir where 4% of lime mass was substituted with coir mass. …
