Electrical and Computer Engineering Commons^™

The Measurement Of Bone Quality In Medical Images Using Statistical Textural Features, Ning Huang

Electrical Engineering Theses

Mineral density and bone architecture properties are the main measures of bone quality. Dual-energy X-ray Absorptiometry (DXA) is the traditional clinical measurement technique for bone mineral density, but it is insensitive to architectural information. Image analysis of the architectural properties of bones can be used to predict bone quality. This study is aimed at investigating the statistical parameters extracted from wo dimensional projection images of the DXA scans and exploring its link with architectural properties, and its correlation with a bones mechanical properties. In this research, features extracted from the Gray Level Co-occurrence Matrix (GLCM) for a 2D image are …

Assessing The Viability Of Sol-Gel Nimgo Films For Solar Blind Detection, Amber Scheurer

HIM 1990-2015

Wide bandgap semiconductors have been broadly investigated for their potential to detect and emit high energy ultraviolet (UV) photons. Advancements in deep UV optoelectronic materials would enable the efficient and affordable realization of many medical, industrial and consumer UV optical devices. The traditional growth method, vacuum deposition, is an extremely complicated and expensive process. Sol-gel processing dramatically simplifies facility requirements and can be scaled to industrial size. The work presented here involves a novel study of the ternary wide bandgap material Ni1-xMgxO. Films were developed by sol-gel spin coating for investigation of material and electrical properties. This method produced films …

Probabilistic Fatigue Life Prediction Model For Alloys With Defects: Applied To A206, R. Kapoor, Vittal S. Rao, R. S. Mishra, J. A. Baumann, G. Grant

Electrical and Computer Engineering Faculty Research & Creative Works

A model for the prediction of fatigue life based on the statistical distribution of pores, intermetallic particles and grains is presented here. This has been applied to a cast Al alloy A206 before and after friction stir processing (FSP). the model computes the probability of initiating a small crack based on the probability of finding combinations of defects and grains on the surface. Crack initiation and the propagation life of small cracks due to these defect and grain combinations are computed and summed to obtain the total fatigue life. the defect and grain combinations are ranked according to total fatigue …

Numerical Characterization Of Yb-Signal-Aided Cladding-Pumped Er:Yb-Codoped Fiber Amplifiers, Qun Han, Yang He, Zhaoxia Sheng, Weiyi Zhang, Jiping Ning, Hai Xiao

Electrical and Computer Engineering Faculty Research & Creative Works

In this Letter, high-power cladding-pumped Er:Yb-codoped fiber amplifiers (EYDFAs) coseeded with a Yb-band signal are numerically characterized according to the wavelength and power of the aiding signal, the length of the gain fiber, and the wavelength of the pump. the results show that properly designing these parameters not only helps to suppress the parasitic lasing and improve the pump conversion efficiency but also helps to improve the output power stability of high-power EYDFAs. © 2011 Optical Society of America.

On The Secrecy Rate Of Multi-Antenna Wiretap Channel Under Finite-Alphabet Input, Shafi Bashar, Zhi Ding, Chengshan Xiao

Electrical and Computer Engineering Faculty Research & Creative Works

This work investigates the effect of limiting source signals to finite-alphabet on the secrecy rate of a multi-antenna wiretap system. Existing works have characterized maximum achievable secrecy rate or secrecy capacity for single- and multi-antenna systems based on Gaussian source signals and secrecy code. Despite the impracticality of Gaussian source, its compact closed-form expression of mutual information motivated broad use of Gaussian input assumption. for practical consideration, we study the effect of finite discrete-constellation on instantaneous and ergodic secrecy rate of multiple-antenna wire-tap channels. Our results demonstrate substantial difference between systems involving finite-alphabet inputs and systems with Gaussian inputs. Results …

Design Guide For Cmos Process On-Chip 3d Inductor Using Thru-Wafer Vias, Gary Vanackern

Boise State University Theses and Dissertations

Three-dimensional (3D) inductors using high aspect ratio (10:1) thru-wafer via (TWV) technology in a complementary metal oxide semiconductor (CMOS) process have been designed, fabricated, and measured. The inductors were designed using 500 μm tall vias with the number of turns ranging from 1 to 20 in both a wide and narrow trace width to space ratios. Radio frequency characterization was studied with emphasis upon de-embedding techniques and resulting effects. The open, short, thru de-embedding (OSTD) technique was used to measure all devices. The highest quality factor (Q) measured was 11.25 at 798MHz for a 1-turn device with a self-resonant frequency …

Monitoring Civil Infrastructure Using Image Template Matching, Vikram Mukesh Patel

Boise State University Theses and Dissertations

Structural health monitoring (SHM) is an active area of research devoted to systems that can autonomously and proactively assess the structural integrity of civil structures. This thesis explores the possibility of monitoring civil structures using image template matching and low-cost embedded data acquisition. By acquiring several consecutive images of a structure, one can determine if movement in the structure has occurred. This information can be analyzed to determine long-term changes within a structure, which can then be used to proactively prioritize maintenance, reduce maintenance costs, and prevent structural failure. This will allow structures to be maintained based on objective data …

Energy Harvesting From Elliptical Machines Using Four-Switch Buck-Boost Topology, Alvin Jay Hilario

Master's Theses

This thesis presents the topic of using the Four-Switch Buck-Boost topology as a DC-DC converter for the Energy Harvesting from Elliptical Machines Project. The project works toward providing a modular synchronous power generation system. Due to the dynamic and sporadic output voltage and power characteristics of the Precor elliptical machine, the system requires a DC-DC converter as a voltage preregulator. The inherent wide input range, high efficiency, and low parts cost of this converter well suit the application. This paper further discusses other topologies and their shortcomings, as well as characterizes the Precor elliptical machine and Enphase Microinverter for interfacing. …

Showcase For The Advantages Of Asynchronous Vs. Synchronous Circuits, Justin Roark

Electrical Engineering Undergraduate Honors Theses

Synchronous circuits dominate the semiconductor industry, but asynchronous circuitry is becoming more popular and will continue to do so, as evidenced by the International Technology Roadmap for Semiconductors. Asynchronous circuits, when compared to synchronous circuits, display tolerance to supply voltage and temperature variation. The goal of this project is to demonstrate these two advantages. The project will compare two microcontrollers, a synchronous 8051 and an asynchronous 8031, which will both play a song under various stresses. Note that an 8031 and 8051 are the same, except for the 8051 includes an on-chip instruction memory, whereas the 8031's is off-chip. When …

Reducing Energy Usage Of Null Convention Logic Circuits Using Null Cycle Reduction Combined With Supply Voltage Scaling, Brett Sparkman

Electrical Engineering Undergraduate Honors Theses

The NULL Cycle Reduction (NCR) technique can be used to improve the performance of the NULL Convention Logic (NCL) circuit at the expense of power and area. However, by decreasing the supply voltage of certain components, the power of the NCR circuit can be reduced. Since NCR has increased performance, it could be possible to decrease the power while maintaining the original performance of the circuit. To verify this, the NCR circuit will be implemented using a 4-bit by 4-bit dual-rail multiplier as the test circuit. This circuit will be simulated in ModelSim to ensure functionality, synthesized into a Verilog …

Low-Power, High-Bandwidth And Ultra-Small Memory Module Design, Qawi Ibnzayd Harvard

Boise State University Theses and Dissertations

The main memory subsystem has become inefficient. The performance gained has come at the expenses of power consumption, capacity, and cost. This dissertation proposes novel module, DRAM, and interconnect architectures in an attempt to alleviate these trends. The proposed architectures utilize low-cost interconnects and packaging innovations to substantially reduce the power, and increase the capacity and bandwidth of the main memory system.

This dissertation develops the theory behind a low-cost packaging technology to create an 8-die and 32-die memory module. The 32-die memory module measures less than 2 cm³.

This dissertation also proposes a 4 Gb DRAM architecture …

Electrical Switching Studies Of Chalcogenide-Based Ion-Conducting Variable Resistance Devices, Beth Rose Cook

Boise State University Theses and Dissertations

In this work, ion-conducting devices using layers of chalcogenide materials are explored as potential non-volatile memory devices. This technology is also known in the literature as conductively bridged RAM (CBRAM), programmable metallization cell (PMC), and programmable conductor RAM (PCRAM; not to be confused with the acronym PCRAM as used to denote phase-change memory).

Electrical measurements with five different programming currents at four temperatures have been performed on two-terminal devices comprised of silver with a metal-selenide and germanium-chalcogenide layer. The metal-selenide layer is Sb₂Se₃, SnSe, PbSe, In₂Se₃, or Ag₂Se. The germanium-chalcogenide …

Semiconductor Laser Device-Level Characteristics, Clement K. Law

Master's Theses

High-speed modulations of the semiconductor lasers are highly desirable in cost-effective optical communication systems.  Developing the experimental setups to extract the characteristics of the semiconductor lasers is vital to the future of the optical research projects.  In this thesis, integrated experimental setup designs have been developed to measure the characteristics of the Vertical Cavity Surface Emitting Laser (VCSEL), Distributed Feedback (DFB), and Fabry-Pérot (FP) lasers.  The measurements of the DC characteristics are optical power versus drive current (L-I) curves (DFB, VCSEL) and optical spectra (FP, DFB, VCSEL).  In addition, the high-speed optical detection measurement of the optoelectronic frequency responses for …

Self-Assembling Organic Semiconductors With Tunable Electronic Properties Based On Novel Asymmetric Phenazine And Bisphenazine, Kyoungmi Jang

UNLV Theses, Dissertations, Professional Papers, and Capstones

Current demands in the area of organic semiconductors focus on both electronic and self-assembling properties. Particularly, one-dimensionally grown nanostructures of small organic semiconductors have drawn much attention for nanodevice fabrication. Self-assembly through various intermolecular interactions has been widely used to produce one-dimensionally grown nanostructures which can be induced by various methods such as rapid solution dispersion, a phase transfer method, vapor annealing, crystallization, and organogelation in conjunction with proper molecular design. Controlling the morphology of the nanostructures plays an important role in achieving desirable properties in optoelectronic device applications. While significant advancements have been made in developing molecular architectures for …

Mathematical Modeling Of Metamaterials, Valjean Elizabeth Elander

UNLV Theses, Dissertations, Professional Papers, and Capstones

Metamaterials are artificially structured nano materials with negative refraction index. The successful construction of such metamaterials in 2000 triggered a great interest in study of metamaterials by researchers from different areas. The discovery of metamaterials opened a wide potential for applications in diverse areas such as cloaking, sub-wavelength imaging, solar cell design and antennas.

In this thesis, we investigate the most popular Drude metamaterial model. More specifically, we first present a brief overview of metamaterials and their potential applications, then we discuss the well-posedness of this model, and develop several numerical schemes to solve it. We implement our schemes using …

Improved Complexity Of Quantum Oracles For Ternary Grover Algorithm For Graph Coloring, Marek Perkowski, Yushi Wang

Electrical and Computer Engineering Faculty Publications and Presentations

The Graph Coloring Grover Algorithm has several applications in logic synthesis, scheduling, allocation, planning, robot motion, robot communication, resource allocation, conflict resolution, floor-planning, and many others.

It can serve as a “generic CSP solver” similar to a general SAT solver.

Model-Based Stripmap Synthetic Aperture Radar Processing, Roger D. West

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Synthetic aperture radar (SAR) is a type of remote sensor that provides its own illumination and is capable of forming high resolution images of the reflectivity of a scene. The reflectivity of the scene that is measured is dependent on the choice of carrier frequency; different carrier frequencies will yield different images of the same scene.

There are different modes for SAR sensors; two common modes are spotlight mode and stripmap mode. Furthermore, SAR sensors can either be continuously transmitting a signal, or they can transmit a pulse at some pulse repetition frequency (PRF). The work in this dissertation is …

Elliptical Machine Dc-Dc Converter For The Energy Harvesting From Exercise Machines Project, Greg Hollister

Electrical Engineering

Designing a DC/DC Converter for the Cal Poly Energy Harvesting from Exercise Machines project requires special attention to the unique operating characteristics of the source and the load. An elliptical machine powered by a person exercising comprises the source, while an AC Inverter makes up the load. This project attempts to integrate the two devices with a custom DC/DC Converter in order to ultimately deliver power back into the power grid.

Development Of A Reconfigurable Multi-Faceted Communications Device Using Partial Dynamic Reconfiguration, Richard Dunkley

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Supporting a variety of communication protocols has typically required extensive hard- ware and Input/Output (I/O) interfaces targeting each protocol specifically. Recent designs in the past ten years have created more dynamic approaches by using Field Programmable Gate Arrays (FPGAs) and embedded hardware to implement or simulate previous hardware I/O designs. With the constant increase in FPGA and embedded technologies the capabilities of dynamic implementations have expanded. This report addresses the design of an up-to-date reconfigurable multi-faceted embedded device targeting recent technological advances in FPGAs.

Educational Applications Of Partial Reconfiguration Of Fpgas, Maysam Sarfaraz

Masters Theses and Doctoral Dissertations

The use of partial reconfiguration (PR) in reconfigurable systems such as Field Programming Gate Arrays (FPGAs) has gained a lot of attention during the past ten years. Recently, Xilinx has released the first commercially available PR implementation for its FPGAs. However, there is a lack of educational tools for PR instruction. In addition, the design and implantation of PR on FPGAs can be beneficial compared with the current communications tools within academia. This thesis presents the design and simulation of several basic modulation schemes within Simulink and System Generator for educational applications in communications classes. In addition, the implementation process …