Electromagnetics and Photonics Commons^™

Design And Fabrication Of An Optical Blade Tip Timing Sensor, Nick Tomlinson

All Theses

Electricity is a vital energy source that powers modern technology. Turbines are heavily relied on in the electric power industry for the conversion of natural energy sources into electricity. These turbines operate under harsh conditions which increase the likelihood of blade damage. Structural health monitoring of a turbine’s blades is important to detect problems before a blade experiences failure. The blade tip timing method can be used to monitor blade vibrations and determine if damage has occurred. An optical blade tip timing sensor is designed and fabricated to advance the field of sensing in the power industry.

Characteristics Of Refractivity And Sea State In The Marine Atmospheric Surface Layer And Their Influence On X-Band Propagation, Douglas Matthew Pastore

Electronic Theses and Dissertations

Predictions of environmental conditions within the marine atmospheric surface layer (MASL) are important to X-band radar system performance. Anomalous propagation occurs in conditions of non-standard atmospheric refractivity, driven by the virtually permanent presence of evaporation ducts (ED) in marine environments. Evaporation ducts are commonly characterized by the evaporation duct height (EDH), evaporation duct strength, and the gradients below the EDH, known as the evaporation duct curvature. Refractivity, and subsequent features, are estimated in the MASL primarily using four methods: in-situ measurements, numerical weather and surface layer modeling, boundary layer theory, and inversion methods.

The existing refractivity estimation techniques often assume …

Fabrication And Measurement Of Lt-Gaas Photoconductive Antennas And Arrays, Zachary Paul Uttley

Graduate Theses and Dissertations

This thesis presents the fabrication and measurement of LT-GaAs based terahertz (THz) photo conductive antennas (PCAs) and arrays. The LT-GaAs THz PCAs are fabricated to serve as reference devices to new 2D material black phosphorous (BP) based THz PCAs. The LT-GaAs and BP devices have identical metallic electrodes, allowing for a comparison of emitted THz intensity and bandwidth. All PCAs have been measured using an open bench pulsed time-domain spectroscopy (TDS) system with a usable bandwidth from 0.1-4 THz, pumped with a 780nm Ti:Sapphire femtosecond laser. The results have shown LT-GaAs devices outperforming BP devices in signal amplitude and bandwidth …

Miniature, Submersible Electromagnetic Pumps Of Molten Lead And Sodium For Gen-Iv Nuclear Reactors Development, Ragai M. Altamimi

Nuclear Engineering ETDs

Heavy metals and alkali Liquid Metals are suitable coolants for Generation IV terrestrial nuclear reactors for operating at elevated temperatures for achieving plant thermal efficiency more than 40% and the thermochemical generation of hydrogen fuel. In addition, the low vapor pressure of these liquids eliminates the need for a pressure vessel and instead operates slightly below ambient pressure. A primary issue with the uses of these coolants is their compatibility with nuclear fuel, cladding and core structure materials at elevated temperatures more than 500oC. Therefore, in pile and out-of-pile test loops have been constructed or being considered for quantifying the …

Tunable Linewidth Chip-Level Lasers Using Hybrid Integration Methods, Charles Porter

All Theses

Photonic integrated circuits (PICs) have significant value in today’s world of research. They enable devices to experience large reductions in size, weight, operation power, and cost (SWAPc), making photonic technology more accessible than ever. The functionality of PICs is greatly enhanced due to the realization of both active and passive devices within a single device structure. This is made possible through hybrid integration, which utilizes various coupling methods to transfer light from an active chip to a passive chip. Hybrid integration technology tremendously expands the capabilities of PICs, leading to a plethora of applications. One significant application is that of …

Adaptive Gps Antenna Array Beam Nulling Effectiveness Under Varying Antenna Element Positioning, Aadesh Neel

Electrical and Computer Engineering ETDs

Global Positioning System (GPS) is an essential part of modern life but is susceptible to same frequency jamming. GPS jamming can add excessive noise to a received low power signal and have the capability to change or completely distort information being sent through the GPS signal. Adaptive antenna arrays have long since been a solution to mitigating GPS jamming via beamnulling algorithms. However, there is little research on the effectiveness of these beamnulling algorithms under varying element positioning. In this work, an adaptive antenna array, consisting of Right-Hand Circularly Polarized (RHCP) nearly square GPS antenna elements, was constructed and tested …

High Performance Scene Generator For Testing Of Imaging Sensors, Austin Modoff

Electrical Engineering Theses and Dissertations

Since the invention of modern solid-state imaging sensors in the 1980s, considerable advancements have been made, improving aspects such as frequency response, dynamic range, resolution, and wavelength diversity, as well as inventing many different types of sensor architectures such as framing sensors and event sensors. While considerable improvements in this field are evolving every day, the methods by which to test and validate these systems remain unchanged. Many of these test platforms require specialized designs to test only one or two specific qualities. For example, a spinning disk in front of a black body source to measure the frequency response …

Adaptive Plasmonic Metasurfaces For Radiative Cooling And Passive Thermoregulation, Azadeh Didari-Bader, Nooshin M. Estakhri, Nasim Mohammadi Estrakhri

Engineering Faculty Articles and Research

In this work, we investigate a class of planar photonic structures operating as passive thermoregulators. The radiative cooling process is adjusted through the incorporation of a phase change material (Vanadium Dioxide, VO₂) in conjunction with a layer of transparent conductive oxide (Aluminum-doped Zinc Oxide, AZO). VO₂ is known to undergo a phase transition from the “dielectric” phase to the “plasmonic” or “metallic” phase at a critical temperature close to 68°C. In addition, AZO shows plasmonic properties at the long-wave infrared spectrum, which, combined with VO₂, provides a rich platform to achieve low reflections across the …

Photophoretic Optical Trapping, Essa Ababseh

Electrical Engineering

Photophoretic Optical Trapping (POT) is a relatively new concept in the field of optics which has potential application in 3D display. The POT is realized by confining a particle within a very small location of the optical system, mostly around the focus. The particle, if captured by the beam, has the potential to print visible 3D images in free space. Our POT system is encapsulated by an acrylic enclosure, which also incorporates a biconvex lens as well as an adjustable focus laser module. Particles are released around the top of the lens’ focal point until the captured particle can be …

Wireless Energy Harvesting System, Matthew Palma, Audrey Toop, Andrew Fahey

Electrical Engineering

The modern world is built upon wireless transmission of data. The signals that carry this data travel through the air, an untapped source of power. Unreceived transmissions are dissipated into useless forms of energy when they should be reclaimed. Wireless electronics can theoretically be powered by harvesting energy from the electromagnetic signals in the wireless internet frequency band. The aim of this project is to develop a system to capture ambient energy, convert it into DC power, and store the power for later use. The product will consist of three subsystems: an antenna receiver, a rectifier and voltage-multiplier, and a …

Design Of Class F-Based Doherty Power Amplifier For S-Band Applications, Kyle Chang

Master's Theses

Modern RF and millimeter-wave communication links call for high-efficiency front end systems with high output power and high linearity to meet minimum transmission requirements. Advanced modulation techniques, such as orthogonal frequency-division multiplexing (OFDM) require a large power amplifier (PA) dynamic range due to the high peak-to-average power ratio (PAPR). This thesis provides the analysis, design, and experimental verification of a high-efficiency, high-linearity S-band Doherty power amplifier (DPA) based on the Class F PA. Traditional Class F PAs use harmonically tuned output matching networks to obtain up to 88.4% power-added efficiency (PAE) theoretically, however the amplifier experiences poor linearity performance due …

High Performance Radar System, Danny Maas

Electrical Engineering

This report covers the design, fabrication, and test of an X-band FMCW radar inspired by the radars from Cal Poly course EE 541, “Advanced Microwave Laboratory.” In this class, 2.4GHz Doppler and FMCW radars are designed and built using consumer off-the-shelf (COTS) components. Operability is the focus of this class, sacrificing performance, accuracy, and precision. this project aims to improve upon those radars by using custom-designed components instead of COTS components and shifting the operating frequency to 10GHz.. The use of custom components can improve output power and frequency stability, and higher frequency reduces component size. The FCC allows amateur …

Design, Modeling, And Testing Of A Novel Inductor For Electric Vehicles: Iron Nitride Soft Magnetic Composites, Sydney F. Fultz-Waters, Jacob Krynock

Materials Engineering

New technology for electric vehicles (EVs) must meet the requirements of higher energy usage, lower costs, and more sustainable source materials. One promising material for EV power system components is iron nitride (IN) soft magnetic composites (SMCs) because of their competitive magnetic properties and high abundance of the source materials. As part of an ongoing program at Sandia National Laboratories, this project focused on using computer modeling to optimize the prototyping process for an iron nitride SMC toroidal inductor to reach a target inductance of 600 μH. Four inductors with different combinations of wiring (26 AWG and 20 AWG) and …

Sky Survey Radio Telescope, Jack E. Mcguigan

Electrical Engineering

This document outlines the design of a radio telescope designed to perform hydrogen line sky surveys. The telescope produces radio images mapping the intensity and relative velocities of hydrogen concentrations to their sky coordinates. Over the course of a day, the telescope images the regions of space visible to it, allowing sky survey imagery to be updated daily. Sky survey images are comprised of an array of pixels corresponding to specific sky coordinates. Each 8-bit RGB pixel contains information on the concentrations of hydrogen in the brightness and relative velocity in the color. Radio images mapping the concentrations and velocities …

Characterization Of Low Power Hfo2 Based Switching Devices For In-Memory Computing, Aseel Zeinati

Theses

Oxide based Resistive Random Access Memory (RRAM) devices are investigated as one of the promising non-volatile memories to be used for in-memory computing that will replace the classical von Neumann architecture and reduce the power consumption. These applications required multilevel cell (MLC) characteristics that can be achieved in RRAM devices. One of the methods to achieve this analog switching behavior is by performing an optimized electrical pulse. The RRAM device structure is basically an insulator between two metals as metal-insulator-metal (MIM) structure. Where one of the primary challenges is to assign an RRAM stack with both low power consumption and …

Theory, Simulation, And Experiments On A Magnetically Insulated Transmission Line Terminated By A Bremsstrahlung Diode, Troy Clay Powell

Electrical and Computer Engineering ETDs

Foundational concepts necessary for power flow analysis of a self-magnetically insulated transmission line (MITL) are introduced in theoretical form and several developments to the theory are described. These include cold-cathode electron emission physics, self-magnetic insulation physics, self-limited MITL current, and relativistic secondary ion production from anode surfaces. Modeling these physics is performed using EMPIRE, an electromagnetic particle-in-cell code.

Self-limited MITL current theory described numerically by Pointon is developed here in analytic form and is then used to drive simulations to compare to experiments that were performed in EMPIRE. Carefully calibrated current sensors from HERMES-III experiments show good agreement with EMPIRE …

Micro-Faraday Cage Design And Analysis For Rf Sensitive Components On An Ltcc Substrate In Hfss, Roberto Quezada

Electrical Engineering Undergraduate Honors Theses

This thesis focuses on creating and testing two different simulation environments in HFSS and analyzing the effectiveness of a micro-Faraday Cage on the RF Sensitive component by exchanging the SMPS and RF Sensitive component with 25GHz Microstrip Patch Antennas. Modern integrated circuit board systems consist of components that can generate electromagnetic signals and components that may be sensitive to electromagnetic interference. A switched-mode power supply (SMPS) is one component capable of producing electromagnetic interference (EMI) through its fundamental and harmonic switching frequency. By using a Faraday Cage to shield the RF-sensitive element, it is possible to reduce its susceptibility to …

A Study On Asymmetric Perfect Vortex: Fractional Orbital Angular Momentum And Nonlinear Interaction, Kunjian Dai

All Dissertations

In this work, the manipulation including generation and detection of the asymmetric perfect vortex (APV) carrying fractional orbital angular momentum (OAM) was demonstrated and discussed. All the manipulation of the modes is in real-time which provides a perfect tool for sensing the dynamic properties of complex media. The OAM-involved nonlinear conversion, specifically the second-harmonic generation (SHG) using the APV and asymmetric Bessel-Gaussian (BG) beams was studied in detail.

The generation and detection of the APV are based on the HOBBIT concept which includes acoustic optical deflector (AOD) and log-polar coordinate transformation optics. The RF signal driving the AOD allows the …

Effect On Focusing Fields By Ferromagnetic Cell Cores In Linear Induction Accelerators, Cooper Guillaume

Senior Honors Theses

In the Los Alamos National Laboratories DARHT facility, there are two perpendicular linear induction accelerators, LIAs. The LIAs’ solenoids produce magnetic fields which focus the electron beam. Simultaneously, the accelerating pulse creates a magnetic field. These two field intensities act upon a ferromagnetic material in the cells to enhance magnetic flux density. Due to the nonlinearity of the material, this flux density will reach a saturation point. In turn, the magnetic field intensity of the axial solenoidal magnetic field will be affected and slightly altered. The width of the electron beam will increase, causing a decrease in effectiveness. Through simulation, …

A Study Of A Monolithic Pulsed Fiber Laser With High-Peak And Average Power, Mark Mihalik

All Theses

Fiber lasers with high peak power, pulse energy and average power have numerous industrial applications. This project aimed to build a Master Oscillator Power Amplification fiber laser using commercial components and specialty fiber designed by Clemson University to exceed the power and energy targets of a previous Q-switched fiber laser design. The specialty fiber has a low numerical aperture of 0.028 and a unique geometric core design to minimize amplified spontaneous emission and reduce nonlinear effects in order to produce a high-peak power and high per pulse energy. The two stage, monolithic design targets 3.1 mJ per pulse, average power …