Electrical and Electronics Commons^™

3d Fdtd Method For Modeling Of Seismo-Electromagnetics Disturbance On Crustal Earth, Nabila Husna Shabrina, Yasuhide Hobara, Achmad Munir

Makara Journal of Technology

The paper deals with the modelling of seismo-electromagnetics disturbance on the crustal earth by use of threedimensional (3D) finite-difference time-domain (FDTD) method. The model is built up by discretizing the frontier geographical region between Java Island and Sumatra Island in a cylindrical coordinate system-based 3D object. The proposed method is applied to compute and analyze electromagnetics (EM) fields of the observed very low frequency (VLF) wave used for the investigation. Boundary condition of uniaxial perfectly matched layer (UPML) are applied surrounding the area of computation for truncating the object of simulation. The investigation are focused on the propagation time of …

Experimental Evaluation Of Three Different Humidity Conditions To Physical And Mechanical Properties Of Three Different Mixtures Of Unfired Soil Bricks, Heru Purnomo, Srikandi Wahyu Arini

Makara Journal of Technology

Unfired brick is considered as a more environmentally friendly material than fired brick. It has lower mechanical properties than that of fired brick where humidity influences both bricks. Physical and mechanical properties of unfired bricks made of three kinds of mixtures were studied experimentally under three humidity conditions. The first kind of unfired brick was made only with soil and water while the second type was made of a mixture of soil, water and lime, and the third type was a mixture of soil, water, lime and uniform treated coir where 4% of lime mass was substituted with coir mass. …

Smart Charging Of Future Electric Vehicles Using Roadway Infrastructure, Sara Ahmed, Ethan Ahn, Mahmoud Reda Taha, Samer Dessouky, Moneeb Genedy, Daniel Fernandez, Ann Sebestian, Patience Raby

Publications

Inspired by the fact that there is an immense amount of renewable energy sources available on the roadways such as mechanical pressure and frictional heat, this study presented the development and implementation of an innovative charging technique for future electric vehicles (EVs) by fully utilizing the existing roadways and the state-of-the-art nanotechnology and power electronics. The project introduced a novel wireless charging system, SIC (Smart Illuminative Charging), that uses LEDs powered by piezoelectric nanomaterials as the energy transmitter source and thin film solar panels placed at the bottom of the EVs as the receiver, which is then poised to deliver …

Residential Electricity Management And Protection System, Ejimonu Kosisochukwu Gabriel

Journal of International Technology and Information Management

The Residential Electricity Monitoring System is an electricity meter connected to the Internet to provide real time data on the power system in your home. The REMS is designed to replace the distribution board allowing it to conduct a series of tests on the quality of the electricity supply to your home/facility and, within your home detect basic wiring faults and allow owners and service providers to identify potential problems with the electrical systems.

The electrical monitoring system finally puts proper electrical control into the hands of the home owner by providing him with the ability to control power distribution …

Solarpede: An Untethered Micro Robot Powered By Light., Jordan Fredrick Klotz

Electronic Theses and Dissertations

Micro-Robotics looks to implement robotics principles at a small scale and has gained popularity in recent decades as a gateway to new research areas such as micro-factory applications. The SolarPede is a second-generation, cm-scale micro-crawler designed for such micro factory applications which is equipped with a legged locomotion system and an electronic backpack. The SolarPede is an evolution of its predecessors and features power and signal conditioning capabilities, gait pattern generation, and Bluetooth connectivity. The components which make up SolarPede have been full validated and tested, and its systems have been realized in the form of a body made from …

Energy Transformation And Conservation Investigation, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use a thermoelectric generator module to analyze the relationship between thermal and electrical energies. Using data collection sensors and analysis software, students will investigate the relationship between the temperature gradient across a thermoelectric generator module and the resulting electrical potential. Students will then use their data and analysis to solve problems relating to waste thermal energy in electrical systems and communicate their work to their peers and teacher.

The Comparative Analysis Of The Performances Of Four And Six Pole Pairs Permanent Magnet Synchronous Generator, Ra Msuya

Tanzania Journal of Engineering and Technology (TJET)

Wind power applications using multi-poles permanent magnet generators have become very attractive especially in small ratings. Low-speed multi-pole PM generators are maintenance-free and may be used in different climate conditions. Most of the low speed wind turbine generators presented is permanent magnet machines, which have advantages of high efficiency and reliability since there is no need of external excitation and conductor losses are removed from the rotor. From the study two types of PM AC generator are designed with 6 pole pairs and the other one with 4 pole pairs. These generators were designed and analysed using Maxwell software. The …

Nonlinear Direct Torque Control Of Interior Permanent Magnet Synchronous Motor Drive, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents a nonlinear direct torque control (NDTC) strategy of interior permanent magnet synchronous motors (IPMSMs) for electric vehicle (EV) propulsion. The proposed NDTC scheme applies a nonlinear model of IPMSM to dynamically determine the optimal switching states that optimize the EV drivers’ decision to reduce the workload. Moreover, the proposed NDTC method has a simple control structure and can explicitly handle system constraints and nonlinearities. The performance evaluation is conducted via a prototype IPMSM test-bed with a TMS320F28335 DSP. Comparative experimental results provide the evidence of improvements of the proposed NDTC strategy over the conventional DTC strategy by …

Neurostimulator With Waveforms Inspired By Nature For Wearable Electro-Acupuncture, Jose Aquiles Parodi Amaya

LSU Doctoral Dissertations

The work presented here has 3 goals: establish the need for novel neurostimulation waveform solutions through a literature review, develop a neurostimulation pulse generator, and verify the operation of the device for neurostimulation applications.

The literature review discusses the importance of stimulation waveforms on the outcomes of neurostimulation, and proposes new directions for neurostimulation research that would help in improving the reproducibility and comparability between studies.

The pulse generator circuit is then described that generates signals inspired by the shape of excitatory or inhibitory post-synaptic potentials (EPSP, IPSP). The circuit analytical equations are presented, and the effects of the circuit …

A Low-Cost Experimental Testbed For Multi-Agent System Coordination Control, Victor Fernandez-Kim

LSU Master's Theses

A multi-agent system can be defined as a coordinated network of mobile, physical agents that execute complex tasks beyond their individual capabilities. Observations of biological multi-agent systems in nature reveal that these ``super-organisms” accomplish large scale tasks by leveraging the inherent advantages of a coordinated group. With this in mind, such systems have the potential to positively impact a wide variety of engineering applications (e.g. surveillance, self-driving cars, and mobile sensor networks). The current state of research in the area of multi-agent systems is quickly evolving from the theoretical development of coordination control algorithms and their computer simulations to experimental …

Cost Effective, Highly Efficient Wireless Power Transfer Systems For Ev Battery Charging, Amir Masoud Bozorgi

LSU Doctoral Dissertations

The impact of changing inner diameter of wireless power transfer (WPT) coils on coupling coefficient is studied. It is demonstrated that at a certain outer and inner coil diameter, turn space variation has minor effect on the coupling coefficient. Next, two compensation networks, namely primary LCC and secondary LCC, which offer load-independent voltage transfer ratio and zero voltage switching for WPT, are presented. For both compensation networks, the condition for having zero voltage switching operation are derived. In addition, load-independent voltage transfer ratio (VTR) frequencies are obtained and VTR at each frequency is derived. Then, required equations for calculation of …

Weight Controlled Electric Skateboard, Zachary Barram, Carson Bertozzi, Vishnu Dodballapur

Computer Engineering

Technology and the way that humans interact is becoming more vital and omnipresent with every passing day. However, human interface device designers suffer from the increasingly popular “designed for me or people like me” syndrome. This design philosophy inherently limits accessibility and usability of technology to those like the designer. This places severe limits of usability to those who are not fully able as well as leaves non-traditional human interface devices unexplored. This project set out to explore a previously uncharted human interface device, on an electric skateboard, and compare it send user experience with industry leading human interface devices.

Dc To Dc Usb-C Charger, Nikki Gmerek, Kenneth Nguyen, Uriel Serna

Electrical Engineering

The DC House USB-C Charger will convert the 48V input from the DC house, found on the Cal Poly campus, to 3 USB-C outputs: 5V, 12V, and 24 volts. The converter will deliver a total of 185 Watts out across all 3 outputs, with an efficiency greater than 82% at full load. The USB-C ports will be used to connect to compatible phones, laptops or any other device for charging/powering purposes. The goal of this project is to develop the most efficient and safe converter to deliver power to multiple outputs using USB-C, for items as small as a cell …

Underwater Remotely Operated Vehicle Controller With Pid Stability Regulation, Christian E. Aguirre

Electrical Engineering

The earth’s oceans and rivers remain widely unexplored. Hobbyists and companies across the globe invest money and resources into remotely operated vehicles (ROV) to further expand underwater knowledge. Each ROV includes a controller that operates motors and monitors other crucial system vitals. The ROV Controller project makes the process of designing an ROV simpler and more affordable by providing a multi-purpose programmable controller.

The ROV controller features programmable digital inputs/outputs and analog inputs. The controller processes control signals from analog joysticks, digital signals from a gyroscope and utilizes a MUX to expand the analog input capabilities of the Arduino. The …

Dc-Dc Converter For Electric Vehicle, Jason Y. Zhou, Nicholas James Mah

Electrical Engineering

In this work, a DC-DC converter is designed for an electric vehicle. The DC-DC converter is designed to provide 500W with a 200-400V input and a 12-15V adjustable output. Electric vehicle sales are beginning to increase in popularity and the need for DC-DC converters to siphon power from the tractive system is not yet fully satisfied, especially for single-seater class vehicles. Additionally, improving performance in efficiency without sacrificing wide input voltage range can benefit future DC-DC converter designs. In the end, a forward active clamp DC-DC converter is designed and tested. Additionally, spreadsheet calculators, LTSpice simulations, and Matlab scripts were …

Human Sensing Expansion For A Rolling Robot, Eric Hanson

Electrical Engineering

For the past twenty years, fans of the Star Wars movies have been building their own replica robots or “droids” that they fell in love with on the big screen. This project takes an existing design for the BB-8 droid and integrates sensors that can detect people and then interact with them. This design uses six IR sensors and one main 8x8 IR sensor grid to be able to detect the closest person and turn BB- 8’s dome towards them as though they are looking at them.

Gr802.11 Jamming Detector, Grant A. Blake

Computer Engineering

One important component of a jamming-resistant 802.11 network is detecting the presence of a jammer during normal operation. This is required so that communications on the network can operate at full efficiency when no jammer is present, but switch to a less efficient, but more resilient protocol when the network is under attack. This paper describes a potential method for detecting some common forms of jamming, lays out a plan to test the effectiveness of the detection method, and summarizes the implementation and results of the test plan.

Tidalsim Senior Project Report, Kent Zhang, Colin Vandervoort

Computer Engineering

Throughout the course of this project, our team helped the Cal Poly Biological Sciences department refine an intertidal zone simulator. The aim of this device is to allow any marine biologist to easily simulate a vast range of tidal zones in order to test animal behaviors within these zones. Another goal of this project is to make each simulation tank independent from the others by using a single microcontroller to handle all inputs and outputs of the system as well as logging all relevant data. The current system is set up so that a separate microcontroller handles dissolved oxygen and …

Designing A Simulator For An Electrically-Pumped Organic Laser Diode, Robert Hulbert

Master's Theses

Organic semiconductors provide an alternative set of basis materials to fabricate electronic devices like PN Junctions, LEDs, and FETs. These materials have several benefits over traditional inorganic semiconductors including their mechanical flexibility, reliance on renewable resources, and inexpensive large-scale manufacturability. Despite the contemporary device implementations with organic semiconductors, a solid-state electrically-pumped organic laser diode does not exist. However, organically-based lasers do exist by utilizing the organic material strictly for optical gain. The challenge occurs when charge carriers appear in the organic material. The charge carriers must reach a concentration such that population inversion occurs producing optical gain. However, between the …

Smart Dc Wall Outlet Design With Improved Load Voltage Detection, Patrick Donovon Granieri

Master's Theses

A standard home in the United States has access to the 120V AC power grid for use with home appliances. Many electronics used at home are powered by a DC power supply, which loses energy in the conversion from AC power. The DC House project avoids any conversion between AC and DC by storing energy in batteries as DC power and supplying it directly to DC appliances. While AC systems feature a standardized output voltage, no such standard exists for DC systems. The Smart DC Wall Outlet solves this by automatically adjusting its output voltage to meet any required DC …