Electrical and Electronics Commons^™

Transformer Fault Event Detection And Classification Using Pmus, Yadunandan Paudel

Theses and Dissertations

Transformer is one of the most reliable components in an electric power system, however its failure has huge opportunity costs for an electric utility. In this work, we detect transformer electrical faults promptly and accurately classify the fault types using voltage/current data from Phasor Measurement Units. Our work can also eliminate uncertainties which are inherent in traditional transformer fault diagnostic techniques like dissolved gas analysis. In this thesis, first, possible causes of transformer failures are discussed, and four common transformer electrical faults are identified. Second, a comprehensive simulation model for electrical faults is developed. Third, fast and efficient abrupt change …

Challenges And Signal Processing Of High Strain Rate Mechanical Testing, Barae Lamdini

Theses and Dissertations

Dynamic testing provides valuable insight into the behavior of materials undergoing fast deformation. During Split-Hopkinson Pressure Bar testing, stress waves are measured using strain gauges as voltage variations that are usually very small. Therefore, an amplifier is required to amplify the data and analyze it. One of the few available amplifiers designed for this purpose is provided by Vishay Micro-Measurements which limits the user’s options when it comes to research or industry. Among the challenges of implementing the Hopkinson technology in the industry are the size and cost of the amplifier. In this work, we propose a novel design of …

Receptor-Doped Organic Transistors: Transducing Anion Binding From Mixed Ionic-Electronic Transport, Anthony Benasco

Dissertations

Organic semiconductors based on π-conjugated polymers show remarkable properties such as high tolerance to structural defects, low processing temperature requirements, biocompatibility, ease of fabrication, and tunable properties. Conjugated polymers integrated into device arrays can exhibit collective properties sensitive to minor perturbations in the surrounding media. However, these devices rely on serendipitous sensitivity to the analyte of interest, and strategies for specific detection remain a considerable change. There remains a compelling, global need for technologies to monitor phosphate due to its prevalence in agricultural runoff, leading to fish kills and economic decline for commercial and recreational fisheries. The strong hydration energies …

A Broadband Cp Elliptical-Slot Antenna For Ambient Rf Energy Harvesting, Khatereh Nadali, Patrick Mcevoy, Max Ammann

Conference papers

In this paper, a compact broadband CPW-fed circularly polarised elliptical-slot antenna with an inverted- L tuning stub is proposed. The antenna impedance is optimized for broadband operation from 1.62 GHz to 2.97 GHz. The measured CP bandwidth is 934 MHz (1.747-2.681 GHz), that covers common wireless communication bands GSM 1800, GSM 1900, 3G/LTE 2100, 3G/LTE 2300, 4G/LTE 2500, and 2.4GHz Wi-Fi bands. This makes the designed antenna an appropriate candidate for ambient RF energy harvesting purposes.

Worksheet 01 - Monopole, Ashanthi Maxworth Phd

Antenna Design With HFSS

This worksheet guides users on modeling a quarter-wavelength monopole antenna on an infinite ground plane and observing its characteristics. The worksheet starts with parameter settings and continues on to antenna design, boundary setting, radiation setting, and then to simulation and viewing the results.

Worksheet 04 - Dipole, Ashanthi Maxworth Phd

Antenna Design With HFSS

This worksheet shows how to create a half-wavelength dipole, set the feeder through a port, observe directivity, half-power beamwidth, etc.

Worksheet 05 - Loop, Ashanthi Maxworth Phd

Antenna Design With HFSS

In this worksheet, the users can design a small loop. The small loop shows low directivity, hence at the end of the worksheet, the users can chanage the design parameters and increase the directivity.

Worksheet 07 - Bicone, Ashanthi Maxworth Phd

Antenna Design With HFSS

In this worksheet, setps are given to design a full-wavelength biconical antenna. This is a broadband antenna. The worksheet also shows how to observe surface currents.

Worksheet 06 - Arrays, Ashanthi Maxworth Phd

Antenna Design With HFSS

This worksheet designs an antenna array with three identical dipole elemetns. The antenna is operating as a broadside array. By changing the parameters the users can view the grating lobes in addition to the main lobe.

Worksheet 09 Horn, Ashanthi Maxworth Phd

Antenna Design With HFSS

This worksheet designs a pyramidal horn antenna fed by a waveport.

Worksheet 03 - Near Field, Ashanthi Maxworth Phd

Antenna Design With HFSS

This worksheet guides students to change the observational region between, reactive near field, radiating near field, and far-field.

Worksheet 08 - Helix, Ashanthi Maxworth Phd

Antenna Design With HFSS

This worksheet creates a helical antenna operating in the axial mode. The antenna is mounted on a ground plane. The users can change the circumference of the helix and change the operating mode to broadside or conical if they wish.

Worksheet 10 - Patch, Ashanthi Maxworth Phd

Antenna Design With HFSS

In this worksheet, steps are given to create a slotted rectangular microstrip patch antenna with an inset feed using a stripline. The patch antenna is operating in the TM10 mode.

Worksheet 02 - Meshing, Ashanthi Maxworth Phd

Antenna Design With HFSS

This worksheet is designed to oberserve the variations in results when the mesh is varied from coarse to fine, hence how to find the optimum mesh size such that we can get accurate results while not compromising computational power.

Automated Robotic Light Bulb Testing Platform, Agha I. Akram, Muhammad Ali Ummy

Publications and Research

The main purpose of this project is to create a functional prototype of a multilayered system that incorporates aspects of electrical, mechanical, and computer engineering technology. The main objective of the system is to be able to determine whether a light bulb is working or not. The building blocks of this system are a robotic arm that is able to slide along a rail (for added mobility), a conveyor belt, and an electromechanical device that holds and tests light bulbs. Initially, the robot arm picks up a light bulb and places it into the holder which then tests it. A …

Hinged Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Jeremiah C. Williams, Hengky Chandrahalim

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) sensor includes a three-dimensional microscopic optical structure formed on a cleaved tip of the optical fighter using a two-photon polymerization process on a photosensitive polymer by a three-dimensional micromachining device. The three-dimensional microscopic optical structure having a hinged optical layer pivotally connected to a distal portion of a suspended structure. A reflective layer is deposited on a mirror surface of the hinged optical layer while in an open position. The hinged optical layer is subsequently positioned in the closed position to align the mirror surface to at least partially reflect a light signal back …

Design Of A Bandgap Voltage Reference, Nicolaus Vail

Electrical Engineering Undergraduate Honors Theses

This thesis details the design process of a bandgap voltage reference (BGR) integrated circuit in a 180 nm CMOS process. A BGR provides a constant DC voltage across a range of operating temperatures and supply voltages. By its nature, the circuit is intended as a reference, not to provide current, so the output would be connected to a very high impedance, such as the gate of a transistor. At 27°C, this design provides a 955 mV reference voltage given a nominal VDD of 3 V. From 20°C to 175°C, the output voltage has a variance of 7.2 mV (approximately 0.8%) …

Signal Analysis Of Photovoltaic Systems For Multilevel Cybersecurity, Wesley G. Schwartz

Electrical Engineering Undergraduate Honors Theses

The cybersecurity of grid-connected power electronics is a rapidly developing field as more and more of these devices become a part of the Internet of Things. The objective of this thesis to analyze the current control signals of a photovoltaic (PV) inverter and develop an interface board for the implementation of a new cyber-secure controller.

In this thesis, the testing and in-depth analysis of the current PV inverter control system will be conducted. Using the data collected, an interface board will be developed to allow the use of the Unified Control Board (UCB), developed by Chris Farnell, in the PV …

Grid-Connected Renewable Energy Systems For Residential Hvac Load Management, Oscar Samuel Acosta

Open Access Theses & Dissertations

With an ongoing mission of utility operators to maintain a resilient and reliable power grid in the face of continuously increasing load demand, it is essential that advancements be made in developing both technology and methodology to help account for the increasing energy requirements. According to the U.S. Department of Energy (DOE) and Energy Information Administration (EIA), the residential end-use sector alone counted for 22% of all electricity used in the U.S. in 2020. Of this, approximately 32% of household electricity load is the direct result of air conditioning and space heating units (HVAC). One way to account for this …

Automatic Testing Of Organic Strain Gauge Tactile Sensors., Brian P. Goulet

Electronic Theses and Dissertations

Human-Robot Interaction is a developing field of science, that is posed to augment everything we do in life. Skin sensors that can detect touch, temperature, distance, and other physical interaction parameters at the human-robot interface are very important to enhancing the collaboration between humans and machines. As such, these sensors must be efficiently tested and characterized to give accurate feedback from the sensor to the robot. The objective of this work is to create a diversified software testing suite that removes as much human intervention as possible. The tests and methodology discussed here provide multiple realistic scenarios that the sensors …