Electrical and Electronics Commons^™

Vi Energy-Efficient Memristor-Based Neuromorphic Computing Circuits And Systems For Radiation Detection Applications, Jorge Iván Canales Verdial

Electrical and Computer Engineering ETDs

Radionuclide spectroscopic sensor data is analyzed with minimal power consumption through the use of neuromorphic computing architectures. Memristor crossbars are harnessed as the computational substrate in this non-conventional computing platform and integrated with CMOS-based neurons to mimic the computational dynamics observed in the mammalian brain’s visual cortex. Functional prototypes using spiking sparse locally competitive approximations are presented. The architectures are evaluated for classification accuracy and energy efficiency. The proposed systems achieve a 90% true positive accuracy with a high-resolution detector and 86% with a low-resolution detector.

Modeling And Characterization Of Cmos Logic Gates Under Large Signal Rf Injection, Zahra Abedi

Electrical and Computer Engineering ETDs

This research addresses the issue of electromagnetic interference (EMI) in digital electronics, which can cause undesired behavior in active electronic components and systems. As technology advances and transistor size decreases, devices become more susceptible to EMI. In addition, as voltage is scaled down to save energy, silicon chips become more susceptible to soft errors. While there are several ways to mitigate the impact of severe EMI on digital systems, minimal electromagnetic coupling can still cause significant problems. We develop analytical models to predict device upset due to EMI. The study focuses on identifying vulnerable parameters of operation related to device …

Designing The Power System Of A Robot, Nolan Hays

Honors College Theses

This thesis outlines the acquired skills and knowledge acquired through the course of four years of Murray State University’s School of Engineering. The capstone for students in the department was to team up and complete an interdisciplinary senior design project using skills from various tracks of engineering. For this thesis, there is a greater emphasis on the electrical engineering track. The objective of the project was to build an autonomous robot to complete the various tasks within the scope of the IEEE SoutheastCon 2023 Hardware Competition. The robot was controlled via a Raspberry Pi 4 Model B. There were three …

Sensor Updates For Bigheaded Carp-Tracking Autonomous Boat, Jordan Kaufmann

Honors College Theses

Bigheaded carp are an invasive species that overpopulate and compete with the native species of Kentucky Lake as well as many other North American aquatic ecosystems. The movement patterns of Bigheaded carp are being studied nationwide by the United States Geological Survey and multiple universities. These studies ultimately seek to control their spread and reduce or reverse the ecosystem destabilization caused by this invasive species. Such studies are currently conducted manually on Kentucky Lake by graduate students affiliated with the Murray State University (MSU) Biology Department and Hancock Biological Station, and these manual studies are an arduous and time-consuming effort. …

Relaxing Dc Capacitor Voltage Of Power Electronic Converters To Enhance Their Stability Margins, Ali Zakerian

Theses and Dissertations

Recently, due to the increasing adoption of distributed energy resource (DER) technologies including battery energy storage (BES) and electric vehicle (EV) systems, bidirectional power converters are becoming more popular. These converters are broadly utilized as interface devices and provide a bidirectional power flow in applications where the primary power supply can both supply and receive energy. A dc capacitor, called the dc-link, is an important component of such bidirectional converters. For a wide range of applications, the converter is required to control the dc-link voltage. Commonly, a proportional-integrating (PI) controller is used by the dc capacitor voltage controller to generate …

Design Of High-Power Ultra-High-Speed Permanent Magnet Machine, Md Khurshedul Islam

Theses and Dissertations

The demand for ultra-high-speed machines (UHSM) is rapidly growing in high-tech industries due to their attractive features. A-mechanically-based-antenna (AMEBA) system is another emerging application of UHSM. It enables portable wireless communication in the radio frequency (RF)-denied environment, which was not possible until recently. The AMEBA system requires a high-power (HP) UHSM for its effective communication performance. However, at the expected rotational speed range of 0.5 to 1 million rpm, the power level of UHSM is limited, and no research effort has succeeded to improve the power level of UHSM.

The design of HP-UHSM is highly iterative, and …

Approximate And Sample Entropy Of Center Of Pressure In Unperturbed Tandem Standing: Contribution Of Embedding Dimension And Tolerance, Jayla Mashae Wesley

Masters Theses

Approximate entropy (ApEn) and sample entropy (SampEn) are statistical methods designed to quantify the regularity or predictability of a time series. Although ApEn has been a prominent choice for use, it is currently unclear as to which method and parameter selection combination is optimal for its application in biomechanics. The goal of this thesis was to examine the difference between ApEn and SampEn related to center of pressure (COP) data during standing balance tasks, while also refining tolerance r, to determine entropy optimization. Six participants completed five 30-second, feet together and tandem standing, trials under eyes-open and eyes-closed conditions. Ground …

Design Of A Sigma-Delta Adc In 65nm Cmos Process, Michael Lee Thompson Iii

Electrical Engineering Undergraduate Honors Theses

Analog and digital signals both play a vital role in electrical engineering and the technology of today. As the role of electrical and computer engineers becomes more deeply involved in the development of new technology, an understanding of how these signals are utilized, and what they represent, is a necessity. Due to the inherent limitations involved with analog signals, there is a need for these signals to be accurately and efficiently converted to digital signals for processing. The job of the analog-to-digital converter, or ADC, is to receive this analog input signal (voltage or current) and create a digital representation …

Stream Processor Development Using Multi-Threshold Null Convention Logic Asynchronous Design Methodology, Wassim Khalil

Graduate Theses and Dissertations

Decreasing transistor feature size has led to an increase in the number of transistors in integrated circuits (IC), allowing for the implementation of more complex logic. However, such logic also requires more complex clock tree synthesis (CTS) to avoid timing violations as the clock must reach many more gates over larger areas. Thus, timing analysis requires significantly more computing power and designer involvement than in the past. For these reasons, IC designers have been pushed to nix conventional synchronous (SYNC) architecture and explore novel methodologies such as asynchronous, self-timed architecture. This dissertation evaluates the nominal active energy, voltage-scaled active energy, …

Design And Implementation Of High-Efficiency, Lightweight, System-Friendly Solid-State Circuit Breaker, Dehao Qin

All Dissertations

Direct current (DC) distribution system has shown potential over the alternative current (AC) distribution system in some application scenarios, e.g., electrified transportation, renewable energy, data center, etc. Because of the fast response speed, DC solid-state circuit breaker (SSCB) becomes a promising technology for the future power electronics intensive DC energy system with fault-tolerant capability. First, a thorough literature survey is performed to review the DC-SSCB technology. The key components for DC-SSCB, including power semiconductors, topologies, energy absorption units, and fault detection circuits, are studied. It is observed that the prior studies mainly focus on the basic interruption capability of the …

Effect On Focusing Fields By Ferromagnetic Cell Cores In Linear Induction Accelerators, Cooper Guillaume

Senior Honors Theses

In the Los Alamos National Laboratories DARHT facility, there are two perpendicular linear induction accelerators, LIAs. The LIAs’ solenoids produce magnetic fields which focus the electron beam. Simultaneously, the accelerating pulse creates a magnetic field. These two field intensities act upon a ferromagnetic material in the cells to enhance magnetic flux density. Due to the nonlinearity of the material, this flux density will reach a saturation point. In turn, the magnetic field intensity of the axial solenoidal magnetic field will be affected and slightly altered. The width of the electron beam will increase, causing a decrease in effectiveness. Through simulation, …

Control And Design Of A Passive Solar Lumber Drying Kiln, Peter Chardavoyne

Honors Scholar Theses

The passive solar lumber drying kiln design, developed by EE Senior Design Team 2317 is presented, tested, and discussed. The design incorporates solar power and a custom control system to dry 12’ lumber boards inside a shipping container much faster than air-drying methods, which can take up to a year for thorough drying, though this can be extended due to the unpredictability of weather events and conditions. This work presents the design as in the final report provided by the team, but provides a more detailed explanation and analysis of the microcontroller system, testing methods and outcomes, alternate solutions and …

Universal Short-Circuit And Open-Circuit Fault Detection For An Inverter, Buck Brown

All Theses

Short-circuit and open-circuit faults of an inverter’s power device often lead to catastrophic failure of the entire system if not detected and acted upon within a few microseconds, particularly for emerging wide bandgap (WGB) power semiconductors. While a significant amount of research has been done on the fast and accurate protection and detection of short-circuit faults, there has been less success corresponding to the research on open-circuit faults. Common downfalls include protection and detection that are too application-specific, take longer than a couple of microseconds, and are not cost-efficient. This study proposes a new open-circuit fault protection and detection system …

Photovoltaics, Batteries, And Silicon Carbide Power Electronics Based Infrastructure For Sustainable Power Networks, Prahaladh Paniyil

All Dissertations

The consequences of climate change have emphasized the need for a power network that is centered around clean, green, and renewable sources of energy. Currently, Photovoltaics (PV) and wind turbines are the only two modes of technology that can convert renewable energy of the sun and wind respectively into large-scale power for the electricity network. This dissertation aims at providing a novel solution to implement these sources of power (majorly PV) coupled with Lithium-ion battery storage in an efficient and sustainable approach. Such a power network can enable efficiency, reliability, low-cost, and sustainability with minimum impact to the environment.

The …

A Nonlinear-Model-Based High-Bandwidth Current Sensor Design For Switching Current Measurement Of Wide Bandgap Devices, Xia Du, Liyang Du, Yuxiang Chen, Yuqui Wei, Andrea Stratta, H. Alan Mantooth

Electrical Engineering Faculty Publications and Presentations

With the growing adoption of wide bandgap devices in power electronic applications, current sensor design for switching current measurement has become more important. The demands for high accuracy, high bandwidth, low cost, compact size, and galvanic isolation pose significant design challenges. The conventional modeling approach for bandwidth analysis of current transformer sensors assumes that the magnetizing inductance remains constant, which does not always hold true in high-frequency operations. This can result in inaccurate bandwidth estimation and affect the overall performance of the current sensor. To address this limitation, this paper provides a comprehensive analysis of nonlinear modeling and bandwidth, considering …

Addressing The Challenged Of Dcop Based Decision-Making Algorithms In Modern Power Systems, Luis Daniel Ramirez Burgueno

Open Access Theses & Dissertations

Natural disasters have been determined as the leading cause of power outages, causing not only huge economic losses, but also the interruption of crucial welfare activities and the arise of security concerns. Because of the later, decision-making considering grid modernization, power system economics, and system resiliency has been a crucial theme in power systemsâ?? research. The need to better withstand catastrophic events and reducing the dependency of bulky generating units has propelled the development and better management of behind-the-meter generation or distributed energy resources (DERs). DERs can assist in the grid in different manners, not only by meeting energy demand …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Multiple Output Power Supply Using Toroidal Transformers For Medium Voltage Active Gate Drivers, Samhitha Venkata Machireddy

Graduate Theses and Dissertations

When operating in high power applications, power devices dissipate tens or hundreds of watts of power in the form of heat. The ability of the power devices to withstand power and dissipation of heat across the power devices becomes a prominent requirement in designing the power converter. This challenge demands a power converter design to be more effective and consistent which factors in size, cost, weight, power density and reliability. This study aims to propose a gate driver isolated power supply design that can be used in medium voltage applications (e.g., up to 10 kV) while respecting the principle of …

Analysis Of An Isolated Bidirectional Ćuk Converter, Yeny Hau Chen

Graduate Theses and Dissertations

The objective of this thesis is to perform an analysis of the isolated bidirectional Ćuk dc-dc converter topology and demonstrate the advantages and operation of this configuration through simulations using MATLAB/SimulinkTM and measurements collected from a 1.5-kW prototype tested at the Engineering Research Center (ENRC) laboratory of the University of Arkansas. The idea of integrating an active-clamp snubber circuit on each side of the converter, proposed by Dr. Sudip Mazumder from the University of Illinois, Chicago, limits the additional voltage stresses on the components due to the energy from the transformer’s leakage inductance. This is studied in this thesis to …

Cyber-Physical Production Systems And Their Practical Integration And Application With Simio Software, Jose Carlos Garcia Marquez Basaldua

Open Access Theses & Dissertations

Industry 4.0 comprises a diverse array of technologies and components that are revolutionizing the manufacturing industry, from Digital Twins, Cyber-Physical Systems and Augmented Reality. The elements that englobe Industry 4.0 vary from framework to framework. Nevertheless, there are similarities in the available literature on what constitutes Industry 4.0. Some of the most critical components specified by the available literature include Digital Twins and Cyber-Physical Systems. A Factory Digital Twin is a virtual representation of a production system that can mimic the behavior of the physical asset. Moreover, a digital twin must have synchronization with its physical twin (i.e., production floor), …