Electrical and Electronics Commons^™

Single-Ended-To-Differential And Differential-To-Differential Channel-Select Filters Based On Piezoelectric Aln Contour-Mode Mems Resonators, Chengjie Zuo, Gianluca Piazza

Chengjie Zuo

This paper reports on the first demonstration of single-ended-to-differential and differential-to-differential (S2D and D2D) channel-select filters based on single-layer (SL) and dual-layer-stacked (DLS) AlN contour-mode MEMS resonators. The key filter performances in terms of insertion loss (as low as 1.4 dB), operating frequency (250-1280 MHz), and out-of-band rejection (up to 60 dB) constitute a significant advancement over all other state-of-the-art RF MEMS technologies. The fabrication process, namely stacking of two piezoelectric AlN layers (600 nm each) and three Pt electrode layers (100 nm each), is fully compatible with the previously demonstrated AlN RF MEMS switch process (also post-CMOS compatible), which …

Design An X-Band Frequency Synthesizer, Hossein Ameri Mahabadi, A. Attaran, M. Moghavvemi

Hossein Ameri Mahabadi

This frequency synthesizer design aims at achieving low phase and high reliability for X-band digital microwave radio applications, using a commercial device and frequency tripling techniques.

Polyenvi, Stephen Beard, Josh Engel, Paul Fake, Diego Flores, Alvaro Nunez, Miguel Wong

Electrical Engineering

Poor indoor air quality is a problem that is recognized by the Environmental Protection Agency (EPA) to cause health issues. In order to raise awareness of this problem, this document outlines the construction of a device that economically measures air quality through five metrics: dust, smoke, ozone, humidity, and temperature. The device integrates with a router to provide users access to information about their indoor air quality anywhere over the internet as well as local access to the data via an LCD mounted on the router. By increasing indoor air quality awareness, this device will aid users in making adjustments …

The Applications And Limitations Of Printable Batteries, Matthew Delmanowski

Graphic Communication

This study focuses on the potential applications for printed batteries and how they could affect the printing industry. It also analyzes the main problems associated with manufacturing this technology and what needs to be done to overcome these issues. To find the answers to these questions, two methods of research were used. The first was through the elite and specialized interviewing of Dr. Scott Williams of Rochester Institute of Technology and Professor Nancy Cullins from Cal Poly. The second form of research was a common, yet useful, method called secondary research. This entailed looking at recent written research papers about …

Analog Electric Guitar Distortion Effects And Headphone Amplification, Michael Alexander Jenkins

Electrical Engineering

The goal of this project was to create an electronic system which integrates popular audio processing effects as well as headphone amplification circuitry for use with an electric guitar. By implementing a system which fits natively inside the body of an electric guitar, the need for numerous external accessories relating to a standalone amplifier system is eliminated, improving device versatility and portability.

Electric Bicycle System, Robert Cong, Rodney Martinez, Mark Casilang, Peter Vong

Electrical Engineering

The Electric Bicycle System is a systems project that incorporates three different ways of charging a lithium-ion battery: the 120VAC wall outlet, regenerative braking, and solar power; which is used to power an electric hub motor running a bicycle. The purpose of the project is to show that it is possible and relatively simple, to build an electric bicycle by oneself. This project can be broken down into five separate categories: the lithium-ion battery, the DC-DC boost converter, the solar panel, the motor, and the motor controller. Each of these will be built upon and improved further by future students, …

Magnetic Design Web Application, Michael Brim

Electrical Engineering

The automated Magnetic Design Web Application, available at http://www.magneticdesign.org, generates the full design process of a power transformer, gapped inductor and toroidal inductor given design specifications provided by the user. Calculations are accomplished using Area Product, Ap, or Core Geometry, Kg, procedures. All design processes mirror the format used in Dr. Taufik’s Introduction to Magnetic Design lecture-notes. An administrative backend is provided where instructors can add or modify core design values to expand the array of materials used. The project aims to aid student understanding of magnetic design and course concepts while allowing instructors to broaden the scope of material …

Class-D Power Amplifier, Joseph Maldonado, Jeovany Vega

Electrical Engineering

No abstract provided.

Single-Ended Tube-Based Guitar Amplifier, Joseph (Joe) Linn

Electrical Engineering

Since the advent of the transistor, the vast majority of designers and manufacturers of electronic devices have abandoned the vacuum tube. Compared to transistors, tubes are orders of magnitude larger, more power hungry, more expensive, less reliable, and dissipate much more heat. In short, transistors are superior devices for almost all applications. Despite this fact, many makers of high-end audio and instrument amplifiers continue to base their designs on tube technology.

Given all of their shortcomings, the obvious question is: Why bother with tubes? Proponents of tube-based audio amplifiers cite a certain “warmth” that tube circuitry lends to the sound …

Modular Laser Combat System For Remotely Operated Vehicles: Bridging The Gap Between Computer Simulation And Live Fire, Thomas Edward Fulenwider

Master's Theses

In the emerging industry of small unmanned vehicles, pioneered by small businesses and research institutions, a suitable combat system test platform is needed. Computer simulations are useful, but do not provide the definitive proof of effective operation necessary for deployment of a combat system. What is needed is an affordable simulated weapons system that enables live flight testing without the used of live weaponry.

A framework is developed here for the construction of a simulated weapon using Free Space Optical (FSO) infrared communication. It is developed in such a way to ensure compatibility with a variety of platforms including ground …

Negative Conductance Load Modulation Rf Power Amplifier, Cody R. Neslen

Master's Theses

The number of mobile wireless devices on the market has increased substantially over the last decade. The frequency spectrum has become crowded due to the number of devices demanding radio traffic and new modulation schemes have been developed to accommodate the number of users. These new modulation schemes have caused very poor efficiencies in power amplifiers for wireless transmission systems due to high peak-to-average power ratios (PAPR). This thesis first presents the issue with classical power amplifiers in modern modulation systems. A brief overview of current attempts to mitigate this issue is provided. A new RF power amplifier topology is …

Systems Engineering Analysis And Digital Communication Bus Design For The Cal Poly Super Project, Matt Marcus Camack

Master's Theses

With an expected lifetime of 20 years and an expected cost of $500, the Cal Poly Sustainable Power for Electrical Resources (SuPER) project needed a strong central design. This thesis looks at the work completed by students over the previous 5 years, with an eye on the future, to create the phase 2 design. Part of this new structure focuses on a distributed communication bus for monitoring system health and status. Instead of complex and costly computer or FPGA systems, the new system will run solely with microcontrollers. This reduces costs and will hopefully still be used within 5, 10, …

A Constant Conduction Angle Biased Rf Power Amplifier For Improved Linearization In Class C Operation, Greg Lacaille

Master's Theses

Class C power amplifiers offer higher efficiency than class B power amplifiers, but suffer from poor linearity. A feedback based biasing system to improve the linearity of a class C power amplifier is designed. A class B amplifier with a gain of 20 dB and 20 MHz bandwidth at 900 MHz acts as the launching point for the design. The biasing and output network of the class B power amplifier is modified to produce a class C amplifier at conduction angles of 180°, 162°, 126°, 90°, and 54°. A feedback based biasing system, which uses two matched and scaled down …

Pulse Density Modulated Soft Switching Cycloconverter, Jesse Timothy Adamson

Master's Theses

Single stage cycloconverters generally incorporate hard switching at turn on and soft switching at turn off. This hard switching at turn on combined with the slow switching speeds of thyristors (the switch of choice for standard cycloconverters) limits their use to lower frequency applications.

This thesis explores the analysis and design of a pulse density modulated (PDM), soft switching cycloconverter. Unlike standard cycloconverters, the controller in this converter does not adjust thyristor firing angles. It lets only complete half cycles of the input waveform through to the output. This allows and requires a much greater frequency step down from the …

Properties And Device Applications Of Silicon And Silicon-Germanium Nanostructures With Different Dimensions, Han-Yun Chang

Dissertations

Defect-free crystalline Si/SiGe(Ge) nanostructures are demonstrated despite the 4% lattice mismatch between Si and Ge. The lattice mismatch-induced strain is sufficiently relaxed through the designed, cluster morphology, or nanowire (NW) structures. Future device applications of these nano structures require complete understanding of their structural, optical, electrical and thermal properties. This study explores these properties in two-dimensional (2D) Si/Si:B delta-doped multilayers, 2D Si/Si_1-xGe_x planar multilayers, three-dimensional (3D) Si/Si_1-xGe_{x cluster multilayers, one-dimensional (1D) Si NWs and 1D Si/Ge NW heterojunctions (HJs).}

Raman scattering and photoluminescence measurements show that by alternating heavily boron-doped layers with layers of …

Mechanisms For Quality-Of-Service Provisioning In Networks With Extended Services, Zhen Qin

Dissertations

The emerging network traffic with various Quality-of-Service (QoS) requirements creates a demand for QoS service provisioning beyond the best effort service that Internet currently provides. QoS provisioning requires a framework that satisfies users' QoS and cost demand while maximizes benefits for network service providers. It is considered that QoS provisioning involves three issues: a) estimations of the network QoS performance, which can be achieved by performing network measurement; b) dissemination of the measured QoS states throughout the network with states exchanged among different network routers; and c) QoS routing. In this dissertation, these three issues are addressed.

In QoS networks, …

A Comparison Of Software Engines For Simulation Of Closed-Loop Control Systems, Sanket D. Nikam

Theses

A wide array of control system design and simulation software engines is available in market. It includes MATLAB-Simulink, LabVIEW, Maple-MapleSim, Scilab-Scicos, VisSim and Mathematica-Control Professional Suite (CPS). Among all of them MATLAB-Simulink is dominant and widely used software engine. The main aim of this study is to implement different state space control methods for non-linear Furuta pendulum system in each one of them and to compare performance against MATLAB-Simulink.

Different parameters like learning curve, interoperability, flexibility, control design tools, documentation and tech support are considered for efficiency comparison. It is shown that MapleSim has multi-body intuitive physical modeling (acausal) approach …

Power Flow In Railway Electrification Power System, Sisi Li

Theses

This thesis discusses aspects of the design of the railway electrification system (RES) and in particular the electric distribution system for a 2x25 kV railway power system.

The analysis of Railway Power Supplies (RPS) presents a unique type of load flow problem which is characterized by its constant moving loads, dynamically changing load types (constant current/constant power), and its specialized network structure. The autotransformer power supply system with double track was the system studied in this thesis.

The details of the system studied were provided by Caltrain (California Commuter Rail) for a planned high speed extension to Caltrain system. A …

A Study Of Probability Distributions Of Dct Coefficients In Jpeg Compression, Gopal Thirumalai Narayanan

Theses

The Discrete Cosine Transform (DCT) used in JPEG compression has shown excellent energy compaction properties that rival that of the ideal Karhunen-Loève Transform. Lossy compression in JPEG is achieved by distorting 8x8 block DCT coefficients through quantization. It has been shown in literature that DC block DCT coefficients are Gaussian probability distributed and AC block DCT coefficients are Generalized Normal probability distributed.

In this investigation, three probability density models for individual modes of non- quantized AC block DCT coefficients are evaluated and are used as basis for the derivation of probability distributions for quantized block DCT coefficients. The suitability of …

Study Of Methods To Predict Voltage Collapse, Niki Patel

Theses

One of the problems that must be addressed for a secure power system operation is the voltage collapse problem. The ever increasing size and connectivity of the power grid have lead to making the problem more multifarious. Widespread blackouts, similar to the one that occurred in the northeast in August 2003, could result from failure to address the problem.

This thesis presents an overview of the voltage collapse problem and reviews some existing methods to calculate voltage collapse indicators.

Thevenin and Maximum Power Transfer Theorems are used to provide indicators of the proximity of the system to voltage collapse. The …