Electrical and Electronics Commons^™

Community Microgrid Based On Micro-Wind Generation System, Lubna Mariam, Malabika Basu, Michael Conlon

Conference papers

Penetration of renewable energy sources (such as solar/wind) are being explored mostly as micro power generation (μGen) or mega power plant system. In recent years, emphasis has been given on Microgrid (μGrid) systems because of their few advantages over μGen systems in terms of power quality, stability, reliability, economics etc. But the commercial installation of the μGrid system is not yet progressing significantly. This paper presents the techno-economic aspects of μGen and μGrid systems towards the development of grid connected community based μGrid (C-μGrid) system. Emphasis has been given to identify the benefits of the μGrid over the μGen system. …

A New Placement And Integration Method Of Upqc To Improve The Power Quality In Dg Network, Shafiuzzaman K. Khadem, Malabika Basu, Michael Conlon

Conference papers

A new proposal for the placement and integration of UPQC in DG connected microgrid/micro generation (μG) system has been presented here. DG converters (with storage), the load and shunt part of the UPQC will be placed at or after the PCC. The series part of the UPQC will be placed before the PCC and in series with the grid. DC link can be connected to the storage system also. Hence, it is termed UPQCμ_G. The advantages of the proposed UPQCμ_G over the normal UPQC are to compensate voltage interruptions in addition to voltage sags / swells, harmonic …

Economic Challenges And Optimisation Of Ocean Energy Electrical Systems, Fergus Sharkey

Books/Book chapters

No abstract provided.

Effect Of Hafnium-Incorporation On The Microstructure And Dielectric Properties Of Cobalt Ferrite Ceramics, Stephen Josiah Wells

Open Access Theses & Dissertations

The effect of hafnium ion (Hf⁴⁺) incorporation in cobalt ferrite (CFO) was studied. Samples of Hf substituted CFO ceramic (CoFe_2-xHf_xO₄), were synthesized in the laboratory with hafnium concentrations ranging from x=0.000 to x=0.200. X-ray diffraction scans show that the Hafnium CFO crystalizes in the inverse spinel phase. Inclusion of hafnium causes lattice expansion, increasing the lattice parameter from 8.374 í? for pure CoFe2O4 to 8.391 í? for the highest concentration of hafnium tested (x=0.020). The dielectric properties of CFO are greatly enhanced by inclusion of hafnium. The enhancement is due to the …

Reduced-Order Modeling Using Orthogonal And Bi-Orthogonal Wavelet Transforms, Miguel Hernandez Iv

Open Access Theses & Dissertations

It is well known that model reduction methods borrow techniques typically found in data compression, and current state-of-the-art techniques for data compression are based on the wavelet transform. Given these facts, it is surprising that model reduction using wavelets has not received much attention and has not been adequately addressed in the literature. This research seeks to determine if wavelets can be used for model reduction and if wavelet model reduction is a viable alternative to existing model reduction methods.

In this work we propose a novel method for model reduction using wavelets. Specifically, we introduce techniques for deriving wavelet …

Online Nonintrusive Condition Monitoring And Fault Detection For Wind Turbines, Xiang Gong

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

The goal of this dissertation research is to develop online nonintrusive condition monitoring and fault detection methods for wind turbine generators (WTGs). The proposed methods use only the current measurements that have already been used by the control and protection systems of WTGs; no additional sensors or data acquisition devices are needed. Current-based condition monitoring and fault detection techniques have great economic benefits and the potential to be adopted by the wind energy industry. However, there are challenges in using current measurements for wind turbine condition monitoring and fault detection. First, it is a challenge to extract WTG fault signatures …

Electronic Device, Display And Touch-Sensitive User Interface (Dec 2012), Michael E. Miller, Jerald J. Muszak, Michael J. Telek

AFIT Patents

Display devices and methods for operating the same are provided. In one embodiment, the display device has an electronic display having an active area for presenting visual content; a housing holding the electronic display and having an opening allowing a person to view a first portion of the active area; and a bezel about the opening, the bezel covering a second portion of the active area and providing a window through which at least a part of the second portion can be viewed. A sensor system senses when a person is close to touching the bezel or when a person …

Smart Wall Plug Design For The Dc House Project, Edward Constant Sibal

Master's Theses

The DC House project at Cal Poly State University faces a challenge of supplying DC voltage to household appliances. Each appliance in the DC House constitutes a DC load that has a unique voltage and power rating, hence the need to develop a smart DC wall plug that will automatically adjust to the operating voltage required by any DC load. This thesis entails a proof of concept design of the smart DC wall plug which can automatically detect an appliance’s voltage rating. The design employs a dc-dc converter in conjunction with a microcontroller to sense load current to properly adjust …

Conductive Concrete For Electromagnetic Shielding – Methods For Development And Evaluation, Aaron P. Krause

Department of Computer Electronics and Engineering: Dissertations, Theses, and Student Research

This research investigates the development and evaluation innovative methods for the use of conductive concrete as an electromagnetic shield. New testing methods are developed to determine the best conductive components to use in the design of a concrete mixture for shielding that shows the best promise. The conductive concrete mixture has the potential to provide electromagnetic shielding that is cost-effective in terms of construction, operation, and maintenance compared to conventional approaches. Two testing methods, Small Sample Testing and Large Slab Testing, are developed based on standardized testing methods that have been modified for the testing of conductive concrete mixtures. As …

Energy Harvesting Of Human Kinetic Movement, David Marusiak, Julia Carrillo

Electrical Engineering

Development of kinetic energy scavenging applications from the human body necessitates additional research to assist in designating a mounting position for a potential device. A data acquisition system adequately provides a parametric average power comparison among four locations on the body (waist, upper arm, hand, and calf) for both a male and female subject. Experimentally, the hand-held device provided the highest average power. Thus, subsequent investigation at set speeds provides further analysis of the output’s characteristically linear behavior. The physical energy-harvesting device features a plastic tube casing wrapped with the stationary coiled wire through which a neodymium magnet oscillates. While …

Active Diesel Soot Measurement By Laser Opacity, Jonathan Audish, Brian Ko, Edward Ma, Travis Mcdaniel

Electrical Engineering

This project looks into understanding the concentration of soot being omitted by a diesel engine through the creation of an innovative opacity sensor. The system contains a receiver circuit implementing a photodiode, laser with wavelength of 405±10nm, and a microcontroller with analog-to-digital (A/D) converter. As the laser pulsates, the microcontroller collects and processes the data to calculate the amount of soot within the exhaust system. The opacity sensor in our tests will be used on an Isuzu 1.9 liter diesel engine. The elegant design of the system can be integrated into conventional manufacturing molding or casting processes for new exhaust …

Application Of Wireless Power For Charging The Battery Of A Wireless Mouse, Jacob Keast, Vincent Jison

Electrical Engineering

Electronic devices are a part of all modern homes, but restricted by available outlets and the hassle of wires. With the modern wireless mouse, this is also the case. When the battery is low the consumer has several options: it is replaced with a new battery, it can be recharged using a USB wire, or the mouse is placed on a charging dock. This project provides an alternative to these options and allows the mouse’s battery to be charged via wireless inductive coupling. The wireless power charging system that was implemented in this project was successful in its ability to …

Finding The Maximum Magnitude Response (Gain) Of Second-Order Filters Without Calculus, Kenneth V. Cartwright, Patrick Russell, Edit J. Kaminsky

Electrical Engineering Faculty Publications

The maximum gain (with respect to frequency) of second-order filters such as low-pass, high-pass, band-pass, low-pass notch and high-pass notch filters is derived without using calculus. Our method uses the fact that the square of the magnitude response (gain) for these filters can be written as a positive constant divided by a quadratic function of frequency. Hence, the gain is maximized when the denominator of the gain is minimized, which is easily achieved without calculus, as the denominator is parabolic.

Study Of Current Optocoupler Techniques And Applications For Isolation Of Sensing And Control Signals In Dc-Dc Converters, Jake Williams

Graduate Theses and Dissertations

There is a need for power switches that can operate at high voltage, high temperature, and high switching frequencies with low losses. Power switches fabricated from wide bandgap materials such as silicon carbide (SiC) or gallium nitride (GaN) can outperform conventional silicon switches due to material property advantages. Another common problem in grid-connected applications is the need for high voltage-isolation of gate drivers and control circuitry while operating efficiently at the high switching frequencies, high power density, and high temperatures made possible by wide bandgap devices. Transformers cannot operate at the temperatures of these wide bandgap devices and a new …

Thermal And Electrical Parasitic Modeling For Multi-Chip Power Module Layout Synthesis, Zihao Gong

Graduate Theses and Dissertations

This thesis presents thermal and electrical parasitic modeling approaches for layout synthesis of Multi-Chip Power Modules (MCPMs). MCPMs integrate power semiconductor devices and drive electronics into a single package. As the switching frequency of power devices increases, the size of the passive components are greatly reduced leading to gains in efficiency and cost reduction. In order to increase switching frequency, electrical parasitics in MCPMs need to be reduced through tighter electronic integrations and smaller packages. As package size is decreased, temperature increases due to less heat dissipation capability. Thus, it is crucial to consider both thermal and electrical parasitics in …

Design And Analysis Of An Adaptive Asynchronous System Architecture For Energy Efficiency, Brent Michael Hollosi

Graduate Theses and Dissertations

Power has become a critical design parameter for digital CMOS integrated circuits. With performance still garnering much concern, a central idea has emerged: minimizing power consumption while maintaining performance. The use of dynamic voltage scaling (DVS) with parallelism has shown to be an effective way of saving power while maintaining performance. However, the potency of DVS and parallelism in traditional, clocked synchronous systems is limited because of the strict timing requirements such systems must comply with. Delay-insensitive (DI) asynchronous systems have the potential to benefit more from these techniques due to their flexible timing requirements and high modularity. This dissertation …

Computational Design Of The Electrical And Mechanical Performance Of Steerable Mems Antennas, Morgan Andrew Roddy

Graduate Theses and Dissertations

This thesis describes the origins, improvements, and variations of a broadband microwave antenna that can be beam-steered by a micro-electromechanical system (MEMS). The steerable MEMS antenna of this work was comprised of a planar antenna on top of a Silicon membrane. The membrane is etched to create a gimbal hinge structure and a platform which supported the antenna and gave it one or two degrees of freedom of rotation. The antennas presented were broadband and fed by a coplanar waveguide (CPW) transmission line which traversed the hinge structure. The antenna's orientation in space was designed to be changed through electrostatic …

Coastal Physical Vulnerability Of Surabaya And Its Surrounding Area To Sea Level Rise, Sayidah Sulma, Eko Kusratmoko, Ratna Saraswati

Makara Journal of Technology

The study for coastal vulnerability to sea level rise was carried out in Surabaya and its surrounding area, it has focused on calculations of the physical vulnerability index were used coastal vulnerability index (CVI) methods. It was standardized by the multi criteria analysis (MCA) approach according to the study area. The score of each physical variable derived from remote sensing satellite data and the results of studies that have been done, such as modeling results and thematic maps, and then integrated into geographic information systems (GIS). Result of this study shows that the coastal areas of Gresik, Surabaya, and Sidoarjo …

The Effect Of Size And Crumb Rubber Composition As A Filler With Compatibilizer Pp-G-Ma In Polypropylene Blends And Sir-20 Compound On Mechanical And Thermal Properties, Erna Frida

Makara Journal of Technology

Having been researched the development of thermoplastic elastomer material of polypropylene and natural rubber SIR- 20 compound with Crumb Rubber as the filler. Reinforced polypropylene with size 60 mesh with 1 mm, and the composition of the Crumb rubber (30, 40, and 50) wt%. Observed mechanical properties are tensile strength, fracture elongation, Young's modulus, tear strength and impact strength. Thermal properties are analyzed by DSC and DTA/TGA. It is acquired that for the size of 60 mesh crumb rubber tensile strength, fracture elongation, Young’s modulus, tear strength and impact strength are bigger than 1mm size. The addition of 60 mesh …

Cdm Potential In Palm Solid Waste Cogeneration As An Alternative Energy In Aceh Province, Mahidin Mahidin, Izarul Machdar, Muhammad Faisal, Muhammad Nizar

Makara Journal of Technology

Empty Fruit Bunch (EFB) as a solid waste in Crude Palm Oil (CPO) industry does not utilized yet as an alternative energy source to generate electricity. It is well known that use of solid wate (biomass) as an energy source is part of the Clean Development Mechanism (CDM) scheme due to direct reduction of Green House Gases (GHGs) emission and provide a direct contribution to sustainable development. Utilization of EFB as a source of energy is very potential to be implemented in Aceh since this province has 25 CPO Mills at the moment which actively produce about 870,000 ton EFB …