Electrical and Electronics Commons^™

Bipolar Pulse Width Modulation Inverter, Xin Chen, Ryan Harada

Electrical Engineering

The project entails the design of an improved PWM inverter circuit for the inverter lab experiment in the introductory power electronic course. The improved PWM inverter uses bipolar switching with a half bridge control circuit. The inverter utilizes two ICL8038 chip to generate both the control and carrier signals. The improved inverter enhances the system's portability, protection and is easy to understand from the prior design. The improved PWM inverter provides AC variable single phase 65 Hz AC output voltage from DC input signal. The finished product will be used specifically in the EE 410 laboratory course.

Rapid Battery Exchange (Rbx) Charger Interface, Adam Morris

Electrical Engineering

As fossil fuel prices steadily rise and concerns associated with burning the fuels increase, electric vehicle sales continue to grow. According to the U.S. Department of Energy, EV sales “tripled from about 17,000 in 2011 to about 52,000 in 2012” [1]. In order to meet consumer transportation expectations—molded by fuel-powered vehicles—electric cars must have the ability to “refuel” quickly. Rapidly charging an EV’s traction battery poses one solution but doing so requires large power levels “five times as much as the average office consumes,” [2] making rapid charging less than ideal for the masses. Alternatively, swapping an EV’s depleted battery …

Integration Of Pv & Simulated Dc Sources For The Dc House, Arvind Ramesh, Kevin Gingrich, Scott Chau

Electrical Engineering

The DC House, an ever improving project, uses only pure DC power which most renewable energy sources generate, from solar to wind power. The DC House and this project expect a donation of photovoltaic modules to supply a constant source of DC power. At the moment, the DC House desperately needs power sources because not only does the house have various loads unaccounted for, but the distribution system to determine proper power flow needs a redesign. The project chose to account for these issues by implementing a solar panel onto the DC House and a power distribution module to have …

Low Temperature Battery Monitoring And Control System – Lithium-Ion Low Temperature Case Study, Aaron Lee, Richard Tham, Ken Huynh

Electrical Engineering

This open-ended research project, co-advised by Dr. Prodanov and Dr. Dolan, studies electronic and battery failures at low temperatures (between -70 ºC to 0 ºC). The main battery technology used for this project is Lithium-ion. The research project consists of two systems: the monitoring system and the actuating system. This project accomplishes the first part and assesses the feasibility of measuring the internal impedances of batteries for low-Earth-orbit (LEO) satellites as a means to monitor battery health. It also monitors the effects caused by low temperature conditions through internal impedance measurements from 0 ºC through -70 °C. It includes designing …

Clear Circuit Contact Lens, Paul Hecker Ii, Phillip Azar, Alexander Do, Benny Ng, Errol Leon

Electrical Engineering

The clear active contact lens project aims to address safety and hazard awareness with an unexplored field of eye wear technology. With advancements in nanotechnology and the advent of circuits on contact lens, this project is one of the first research and development into this new field, following University of Washington and Google. The team focuses on the safety and biocompatibility of the contact lens for a comfortable ease of use. The designs push the limits of thin film printed technology with its pursuit of fine designs of 250μm antennas. The project streamlines the manufacturing process for a combination substrate …

Ultraviolet Led Biofouling Mitigation, Andrew Lam

Computer Engineering

The goal is to determine if low-cost UV LEDs can mitigate marine biofouling on small glass or acrylic camera lenses. A microprocessor-controlled experimental setup to control the illumination of low-cost UV LEDs of various wavelength and packaging was fashioned. The system consists of a programmed microcontroller, a manufactured LED breakout interface, and a submergible UV LED array enclosed in a borosilicate glass tube. A preliminary qualitative assessment of four different UV LEDs was conducted during a three-week deployment of the experimental setup in the raw seawater system at the Cal Poly Center for Costal and Marine Sciences in Avila Beach, …

Smart Wall Outlet Design And Implementation For The Dc House Project, Kevin Roy Mendoza

Master's Theses

Most everyday AC appliances are designed to operate off of 120V coming from the wall outlet in our homes. This voltage is a standard set from our established infrastructure. Unlike AC devices, DC devices do not have any set standard of voltage they all will run off of. This presents a problem for the DC house as the various loads that will be used will have different required input voltages. One set voltage for a wall outlet will not suffice for the DC House. This Smart Wall Outlet is designed with a DC-DC converter that will have its output voltage …

St. Jude Medical - R&D Robot For Sensor Testing, Andrew Chanul Kim, Stanley Logan Laszczyk, Edgar Nava, Nathan Gall

Electrical Engineering

No abstract provided.

Rapid Battery Exchange Safety And Sensing, Ben John Froelich, Isaac Sungjin Kim

Electrical Engineering

The Rapid Battery Exchange system (RBX) swaps batteries in an electric van, allowing almost continuous operation of the vehicle. The RBX system is designed and built by The Cal Poly Electric Vehicle Engineering Club (EVEC). The system includes the exchange ramp, two battery packs, and the electric “G-Van.” While the vehicle drives using one of the battery packs, the other pack charges in the exchange ramp. When the van’s battery depletes, it drives onto the ramp and swaps the dead battery for the charged one, and the process repeats.

The RBX battery pack safety and sensing project divides into two …

Battery Management System, Michael Desando, Kyle Woody

Electrical Engineering

Problem Statement:

There have been recent reports of multi-million dollar companies having to recall entire projects due to their BMS’s malfunctioning or operating incorrectly. The purpose of this project is to analyze the future of batteries, the Lithium-Ion cell, and to exercise a BMS to better understand its capabilities and possible cases for errors. Lithium ion batteries are intolerant of overcharge and overdischarge. Abuse of this kind can result in high temperatures, venting of gases, fire, or explosion. Therefore battery management systems have been devised to prevent such abuse. Recent events such as fires on the Boeing Dreamliner and the …

Low Voltage Cmos Sar Adc Design, Ryan Hunt

Electrical Engineering

This project centers on the design of a single ended 10-bit successive approximation register analog to digital converter (SAR ADC for short) that easily interfaces to a micro-controller, such as an Arduino. With micro-controller interfacing in mind, the universal data transfer technique of SPI proved an easy way to communicate between the ADC and the micro-controller. The ADC has a range of 1V (highest code value) to 0V (lowest code value) and operates from a single voltage rail value of 1.8V. Typical SPI clock speeds run on the order of 2MHz and with a 10-bit ADC this means a sampling …

Analog Violin Audio Synthesizer, Brandon E. Davis

Electrical Engineering

Abstract In the past decade, music electronics have almost completely shifted from analog to digital technology. Digital keyboards and effects provide more sound capabilities than their analog predecessors, while also reducing size and cost. However, many musicians still prefer analog instruments due to the perception that they produce superior sound quality. Many musicians spend extra money and accommodate the extra space required for analog technologies instead of digital.

Furthermore, audio synthesizers are commonly controlled with the standard piano keyboard interface. Many musicians can perform sufficiently on a keyboard, but requiring a specific skill set limits the size of the market …

Buck-Boost Dc-Dc Converter With Input Protection System For The Energy Harvesting From Exercise Machines Project, Byungjae David Yoo, Sheldon Tyler Kong Ming Chu

Electrical Engineering

Cal Poly’s Energy Harvesting from Exercise Machines (EHFEM) project comprises of multiple subprojects seeking to effectively create a sustainable energy source through harvesting electrical energy generated from physical exercise machines. This project designs and implements a Buck-Boost DC-DC converter using a LT3791-1 4-Switch Buck-Boost Controller, replacing the previous SEPIC design. The DC-DC converter must operate within limits set by the maximum input range of the LT3791-1 controller. An input protection system prevents inputs higher than rated values, which may adversely damage the Buck-Boost DC-DC converter. These inputs include overvoltage transients, average voltage, and current output by the Precor EFX 561i …

Real Time Swim Instructor, Konrad Antoniuk

Electrical Engineering

Both competitive and recreational swimmers want an efficient swim stroke but often lack consistent feedback with technical insight. Competitive swimmers rely on coaches for instruction but have to stop swimming to listen. The Real Time Swim Instructor project provides live feedback to a swimmer so they can feel their stroke correction while they’re swimming. The developing swimmer feels the difference between correct and incorrect form instantaneously.

The project takes on the responsibility of measuring the moving body, accurately determining stroke improvement, functioning under water, and providing recognizable feedback. Additionally, the user can review their swim from data stored in memory. …

Mobile Solar Pv Trainer, Matthew Myers, Matthew Clause, Lawrence Smith

Mechanical Engineering

The aim of the Mobile Solar PV Trainer Project was to design, construct and test a versatile and robust laboratory training rig for the Cal Poly Electrical Engineering department. This project was inspired by the desire of one or more California Polytechnic State University electrical engineering professors to add laboratory components to two established upper division electrical engineering courses in photovoltaic panels and solar power. This report contains a detailed description of the trainer’s desired specifications, our ideation process, a thorough description of the selected trainer design including part drawings, assembly documentation and a bill of materials as well as …

Portable Nano Hydro Generator For The Dc House Project, Caleb David Fink, Victor Olusoji Ojewole, Christopher Mapua Tan

Electrical Engineering

This Senior Project entails the design and testing processes of the Portable Nano Hydro Generator for the continuing DC House Project. No natural resources should go unused, especially in developing countries where they are found in abundance. Small streams in particular have potential to further Professor Taufik's DC House Project that will provide electricity to 1.6 billion people in the world without access to electricity upon completion. The goal of this project is to create a small portable generator that utilizes the discharge from small streams and convert it into useable electricity that could charge a car battery as an …

Protection System For The Energy Harvesting From Exercise Machines (Ehfem) Project, Eric Funsten, Cameron Kiddoo

Electrical Engineering

The goal of the Energy Harvesting from Exercise Machines (EHFEM) project seeks to harness the energy generated by people using exercise machines and deliver this energy to the electric grid [1]. The implementation consists of a protection system, DC-DC converter, and an inverter. This project involves redesigning the existing DC-DC input protection circuit and current limiter for the EHFEM project [2]. The DC-DC converter takes in the power from the exercise machines and converts it to a manageable voltage level for the inverter. Due to a problem where the inverter may overload the converter, a current limiter sets to limit …

Bike Safe: An Automatic Turn Signal System, Betty He Chan, Ricardo Alberto Duran

Electrical Engineering

Bicycles are vehicles that do not require a license to operate and share the road with cars, motorcycles, and other fast moving vehicles. An improper lane change from a bicyclist, such as one without any warning, can lead to great injury or death (especially after sundown). Bike Safe addresses this safety concern by providing a low-cost device that mimics the warning system motorists’ use every day. The system consists of a red brake light and amber turning signal lights that mounts to the rear of the bike, as well as a white headlamp that mounts to the front handlebars. The …

All Purpose Mobile Gps, James C. Smith, Matt Weege, Kevin Peters

Electrical Engineering

The aim of the All Purpose Mobile GPS (The System) is to create a GPS tracking device that can accurately record location and calculate velocity, distance traveled and elevation change even when the satellite signal is lost. This data can later overlay on existing internet-based maps illustrating a trip to oneself or others. The portable tracker consumes very little power achieving several days’ worth of power in a single charge. A solar cell provides a quick battery boost in a pinch. SD Card storage increases compatibility with computers and other forms of data transfer. Data processing, such as viewing the …

Smart Weights, Luke W. Rafla-Yuan, Austin C. Fox

Electrical Engineering

The goal of this project is to design and implement weights which can record and analyze work out patterns. Motivation for this project stems from the high cost of personal training. The hope is that this device will provide many of the benefits a user receives from personal training at only a fraction of the cost. The Smart Weight is designed with an on-board Inertial Measurement Unit providing acceleration, gyroscope, and magnetometer data. A microcontroller records and analyzes changes in motion, feeding this data into Multiplicative Recurrent Neural Network (MRNN) for exercise classification. A Raspberry Pi was chosen as the …