Systems Engineering and Multidisciplinary Design Optimization Commons^™

From Xst To F-117a, Alan Brown

ERAU Prescott Aviation History Program

Learn the remarkable story of stealth technology from the man often referred to as “Mr. Stealth.” From 1975-1989 Alan Brown was a member of Lockheed “Skunk Works”, becoming program manager & chief engineer for the F-117A Stealth Fighter from initial concept until the first production aircraft was built, 1978 to 1982. Hear the inside story of the many challenges faced by the stealth program and how they were solved.

Development Of Functional Requirements For A High-Capacity Airspace System, Noel J. Colon, Jeongjoon Boo, Steven J. Landry

The Summer Undergraduate Research Fellowship (SURF) Symposium

NASA along with other researchers visualizes a future where more aircraft will transport passengers or goods around the world. Thus, they envision increasing air capacity from 10 to 100 times more than the current system without any reduction in efficiency or safety. Many models are being proposed that comply with the necessary requirements to form part of the method needed. However, knowing which of the proposed methods have the most desirable characteristics, such as efficiency and safety, are yet to be determined. For this reason, a standardized method to compare and assess them has to be developed, since is not …

Risk-Based Approach To Assessment Of Advanced Technologies For Conceptual Design, Adipratnia Asmady

Master's Theses

The conceptual design phase of an aerospace system development program is typically characterized by short duration and relatively limited resources, yet design decisions are made that have critical implications on program risk. To address the more aggressive requirements, one of these decisions is the selection of advanced technologies. System developers need to assess advanced technologies early on, but are faced with uncertainties surrounding the potential net benefits. The concept introduced in this study is uncertainty characterization as a way to better understand the associated risk. A framework was developed to guide the interaction between the technology developer and the system …

Standardization Of Human-Computer-Interface For Geo-Fencing In Small Unmanned Aircraft Systems, David Thirtyacre, Robert Brents, Michael Goldfein, David Hunter, B. Terwilliger

Publications

The use of small unmanned aircraft systems (sUAS) has increased significantly in the past year. Geographic fencing (geo-fencing) is software built into most medium-cost consumer sUAS. This software is typically used to limit the altitude above launch point, the flight distance from the transmitting controller, and/or restrict flight inside a no-fly zone. While the concept of a geo-fence is simplistic, the human-computer-interface (HCI) varies drastically among platforms, and even between software iterations on the same platform. This research examines the HCI of three popular consumer-level sUAS with regard to geo-fencing. The software procedures and human interface for the DJI Inspire-1, …

An Iteration On The Horizon Simulation Framework To Include .Net And Python Scripting, Morgan Yost

Master's Theses

Modeling and Simulation is a crucial element of the aerospace engineering design pro- cess because it allows designers to thoroughly test their solution before investing in the resources to create it. The Horizon Simulation Framework (HSF) v3.0 is an aerospace modeling and simulation tool that allows the user to verify system level requirements in the early phases of the design process. A low fidelity model of the system that is created by the user is exhaustively tested within the built-in Day-in-the-Life simulator to provide useful information in the form of failed requirements, system bottle necks and leverage points, and potential …

Subsystem Failure Analysis Within The Horizon Simulation Framework, Ian M. Lunsford

Master's Theses

System design is an inherently expensive and time consuming process. Engineers are constantly tasked to investigate new solutions for various programs. Model-based systems engineering (MBSE) is an up and coming successful method used to reduce the time spent during the design process. By utilizing simulations, model-based systems engineering can verify high-level system requirements quickly and at low cost early in the design process. The Horizon Simulation Framework, or HSF, provides the capability of simulating a system and verifying the system performance. This paper outlines an improvement to the Horizon Simulation Framework by providing information to the user regarding schedule failures …

Sysml Based Cubesat Model Design And Integration With The Horizon Simulation Framework, Shaun Luther

Master's Theses

This thesis examines the feasibility of substituting the system input script of Cal Poly’s Horizon Simulation Framework (HSF) with a Model Based Systems Engineering (MBSE) model designed with the Systems Modeling Language (SysML). A concurrent student project, SysML Output Interface Creation for the Horizon Simulation Framework, focused on design of the HSF Translator Plugin which converts SysML models to an HSF specific XML format. A SysML model of the HSF test case, Aeolus, was designed. The original Aeolus HSF input script and the translated SysML input script retained the format and dependency structure required by HSF. Both input scripts …

The Context Of Tool Control In An Aircraft Assembly Environment Related To Productivity, Taylor Jay Sisson

KSU Journey Honors College Capstones and Theses

The aircraft industry focuses a large portion of its resources on tool control during the assembly of aircraft. Tool control is a strict process that demands time from the assembly process. This time is removed from the value-added time spent actually assembling the aircraft. A study at Lockheed Martin conducted in the Spring of 2016 is discussed that examines the time spent on tool control. Tool control is necessary in aircraft assembly to prevent tools from entering compartments of the aircraft. If such an event occurs, the tool may damage the aircraft. All aircraft assembly processes must be tool controlled, …

Phased Array Antenna Investigation For Cubesat Size Satellites, Kien Dang

Morehead State Theses and Dissertations

A Thesis Presented to the Faculty of the College of Science Morehead State University in Partial Fulfillment of the Requirements for the Degree Master of Science by Kien Dang on April 18, 2016.

Designing A Mobile Space Habitat Analog, Victor Kitmanyen, Matthew Burkhard, Timothy Disher

Human Factors and Applied Psychology Student Conference

No abstract provided.

Ultra-Compact Raman Spectrometer For Planetary Explorations, Derek Davis, James Hornef, John Lucas, Hani Elsayed-Ali, M. Nural Abedin

Electrical & Computer Engineering Faculty Publications

To develop a compact Raman spectroscopy system with features that will make it suitable for future space missions which require surface landing. Specifically, this system will be appropriate for any mission in which planetary surface samples need to be measured and analyzed.

Space Data Integrator (Sdi) And Space Program Integrated Data And Estimated Risk (Spider): Proof-Of-Concept Software Solution For Integrating Launch And Reentry Vehicles Into The National Airspace System (Nas), Devin D. Dickens

Space Traffic Management Conference

The Space Data Integrator (SDI) Project is the initial step to satisfy the Federal Aviation Administration (FAA) strategic initiative to integrate commercial space launch and reentry vehicles into the National Airspace System. The project addresses the needs for greater situational awareness and monitoring, and increased response capability during non-nominal and catastrophic incidents during space operations.

The initial phase of this project leverages current FAA systems, and provide an initial demonstration of capability that will provide for state data from a commercial reentry vehicle to be ingested into a the FAA Traffic Flow Management System, and displayed on Traffic Situation Displays. …

System Architecture Of Small Unmanned Aerial System For Flight Beyond Visual Line-Of-Sight, Kwee Siam Seah

Theses and Dissertations

Small Unmanned Aerial Systems (UAS) have increasingly been used in military application. The application in expanding scope of operations has pushed existing small UAS beyond its designed capabilities. This resulted in frequent modifications or new designs. A common requirement in modification or new design of small UAS is to operate beyond visual Line-Of-Sight (LOS) of the ground pilot. Conventional military development for small UAS adopts a design and built approach. Modification of small Remote Control (RC) aircraft, using Commercial-Off-The Shelf (COTS) equipment, offers a more economical alternative with the prospect of shorter development time compared to conventional approach. This research …

Premature Allocation Of Program Requirements To Suppliers, Bohdan W. Oppenheim

Systems Engineering Faculty Works

The paper presents a discussion of the difficulties of formulating stable requirements early in complex engineering programs, and the severe consequences on program execution. The problems are caused by the need to seek political and funding support for the program. Formal classical Systems Engineering (SE) and Program Management (CSEPM) methodology is based on the assumption that the knowledge to anticipate all interfaces and create good requirements exists early in the program, and it is only a matter of working out the details to build extremely complex devices such as satellites, aircraft, refineries, nuclear power plants and high speed rail. The …

Modeling And Test Of The Efficiency Of Electronic Speed Controllers For Brushless Dc Motors, Clayton R. Green

Master's Theses

Small electric uninhabited aerial vehicles (UAV) represent a rapidly expanding market requiring optimization in both efficiency and weight; efficiency is critical during cruise or loiter where the vehicle operates at part power for up to 99% of the mission time. Of the four components (battery, motor, propeller, and electronic speed controller (ESC)) of the electric propulsion system used in small UAVs, the ESC has no accepted performance model and almost no published performance data. To collect performance data, instrumentation was developed to measure electrical power in and out of the ESC using the two wattmeter method and current sense resistors; …

Techniques For Payload Stabilization For Improved Photography During Stratospheric Balloon Flights, James Flaten, Christopher Gosch, Joseph (Benjamin) Habeck

2017 Academic High Altitude Conference

Payload-box rotation and swing are perennial challenges to achieving high-quality photography (typically videography) during weather-balloon flights to “near-space” (AKA the stratosphere). Continuous camera motion can lead to blurred still photos, nearly-impossible-to-watch video footage, and precludes time-exposure photography required for most astronomical imaging even though altitudes are reached where the daytime sky appears black. Apparently-random payload rotation, persisting even at altitude, can often exceed servo rotation rates and frustrate attempts to do active camera pointing. Here we discuss mostly-passive payload stabilization strategies we, and our collaborators, have used to mitigate and dampen both swing and rotation of suspended payloads on high-altitude …

A Methodology For The Optimization Of Disaggregated Space System Conceptual Designs, Robert E. Thompson

Theses and Dissertations

Optimal design techniques have proven to be an effective systems engineering tool. Using systems architecture as the foundation, this research explores the use of mixed variable optimization models for synthesizing and evaluating disaggregated space system concepts. Model-based conceptual design techniques are used to identify and assess system architectures based upon estimated system cost, performance trades, and cost risk. The Disaggregated Integral System Concept Optimization (DISCO) methodology is introduced, and then applied to representative space-based missions. Several results are obtained that indicate significant cost effectiveness gains from the optimization of multi-orbit and multi-function/multi-orbit disaggregated space systems. The general methodology has broad …

Automatic Building Change Detection In Wide Area Surveillance, Paheding Sidike, Almabrok Essa, Fatema Albalooshi, Vijayan K. Asari, Varun Santhaseelan

Electrical and Computer Engineering Faculty Publications

We present an automated mechanism that can detect and characterize the building changes by analyzing airborne or satellite imagery.

The proposed framework can be categorized into three stages: building detection, boundary extraction and change identification. To detect the buildings, we utilize local phase and local amplitude from monogenic signal to extract building features for addressing issues of varying illumination. Then a support vector machine with Radial basis kernel is used for classification. In the boundary extraction stage, a level-set function with self-organizing map based segmentation method is used to find the building boundary and compute physical area of the building …

Sense And Avoid Uas Project Final Design Report, Katie Peticolas, Cesia Cazares, Trevor Elsbree, Courtney Smith, Herberth Elie Navas

Biomedical Engineering

No abstract provided.

Tesseract, Edgar Uribe, Vanessa Faune

Mechanical Engineering

PolySat is a student-run, Cal Poly research program in which students develop small satellites, known as CubeSats, to be sent into space. Since the start of the program in 2000, PolySat has developed eight 10cm x 10cm x10cm CubeSats. Recently, the team has developed two satellites of double, and triple, that size for NASA-KSC & AI-Solutions and the National Science Foundation. The recent volumetric expansion has been driven by high demand for further satellite functionality, which necessitates large power generation capabilities. To remain competitive in the growing CubeSat industry, PolySat must develop a platform that can provide enough power to …