Propulsion and Power Commons^™

The Propulsive Design Aspects On The World’S First Direct Drive Hybrid Airplane, Ankit Nanda

Doctoral Dissertations and Master's Theses

The purpose of this thesis is to design a safe technology demonstrator by implementing a direct drive propulsion system for a gas-electric hybrid aircraft. This system was integrated on the Embry-Riddle Eco-Eagle for the Green Flight Challenge 2011. The aim of the system is to allow the pilot to use the electric motor as an independent power source to fly the aircraft once at cruise altitude, while having a gas engine to allow for higher power capability.

The system was designed to incorporate the motor and the motor control unit provided by Flight Design and Drivetek AG alongside a Rotax …

Experimental Investigation And Cfd Simulation Of Active Damping Mechanism For Propellant Slosh In Spacecraft Launch Systems, Dhawal Leuva

Doctoral Dissertations and Master's Theses

Motion of propellant in the liquid propellant tanks due to inertial forces transferred from actions like stage separation and trajectory correction of the launch vehicle is known as propellant slosh. If unchecked, propellant slosh can reach resonance and lead to complete loss of the spacecraft stability, it can change the trajectory of the vehicle or increase consumption of propellant from the calculated requirements, thereby causing starvation of the latter stages of the vehicle. Predicting the magnitude of such slosh events is not trivial. Several passive mechanisms with limited operating range are currently used to mitigate the effects of slosh. An …

Innovative Double Bypass Engine For Increased Performance, Sanjivan Manoharan

Doctoral Dissertations and Master's Theses

Engines continue to grow in size to meet the current thrust requirements of the civil aerospace industry. Large engines pose significant transportation problems and require them to be split in order to be shipped. Thus, large amounts of time have been spent in researching methods to increase thrust capabilities while maintaining a reasonable engine size. Unfortunately, much of this research has been focused on increasing the performance and efficiencies of individual components while limited research has been done on innovative engine configurations. This thesis focuses on an innovative engine configuration, the High Double Bypass Engine, aimed at increasing fuel efficiency …

Designing Propulsion Systems For Future Aerospace Applications, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Vibration-Based Health Monitoring Of Multiple-Stage Gear Train And Differential Planetary Transmission Involving Teeth Damage And Backlash Nonlinearity, Andrew Patrick Sommer

Master's Theses

The objective of this thesis is to develop vibration-based fault detection strategies for on-line condition monitoring of gear transmission systems. The study divides the thesis into three sections. First of all, the local stresses created by a root fatigue crack on a pinion spur gear are analyzed using a quasi-static finite element model and non-linear contact mechanics simulation. Backlash between gear teeth which is essential to provide better lubrication on tooth surfaces and to eliminate interference is included as a defect and a necessary part of transmission design. The second section is dedicated to fixed axis power trains. Torsional vibration …

Comparison Of Best Economy And Best Power Mixture Settings In The Purdue University Training Fleet, Charles G. Chrisman

Purdue Polytechnic Directed Projects

Purdue University operates a fleet of Cirrus SR20s as training aircraft. Standard operating procedures for the cruise portion of cross country training flights call for 65% power with a best power mixture, also called rich of peak, as opposed to a best economy setting, also called lean of peak. Previous work demonstrated that fuel consumption rates, cylinder head temperatures, and true airspeeds are lower when best economy is employed compared to best power for the same power output. This study confirmed that best economy is associated with a lower fuel consumption rate and lower cylinder head temperatures but was unable …

Comparison Of Turbine Engine Test Cell Airborne Nanoparticle Count Versus Ambient Background Particle Count, Ryne Larowe

Purdue Polytechnic Directed Projects

With the establishment of the National Test Facility for Aerospace Fuels and Propulsion at Purdue University in October of 2009, new equipment has been acquired to measure and classify exhaust emissions. This facility utilizes the Honeywell F109 turbofan and Pratt & Whitney PT-6 turboprop engine test cells to analyze the emissions and engine operation of new alternative aviation fuels. This observational study investigates what, if any difference there is in the amount of ambient residual Particulate Matter (PM) in the turbofan engine test cell when compared to ambient particle count associated with the Purdue University Airport (KLAF) property. The project …

Analysis And Design Of A Propulsion System Trade Study Tool For A Boeing 376 Series Communications Satellite, Kevin Dunk

Aerospace Engineering

No abstract provided.

Design, Manufacturing And Testing Of An Environmentally-Green Bipropellant Thruster, Alex Bendoyro, Gabriel Sanchez, Erin Stearns, Phillip Takahashi

Aerospace Engineering

This project reviews the design, manufacturing and experimentation process of a green bi-propellant thruster designed to output 5 lbf. The goals were to successfully design, manufacture and test a thruster, while discovering the complications that arise through out the complete design process of a green thruster. The thruster was successfully designed using ideal rocket equations and the design was successfully confirmed using CFD and FEA. Manufacturing of the thruster was fully planned and revealed mild flaws in thruster design. For example some features were not manufacturable to the exact measurements desired. Testing of the engine gave results inconsistent with expected …

Electric Aircraft Propulsion Test Rig Design & Fabrication, Ryan Mayer, Brian Kubicki, Bradley Rodriguez, Austin Harris, David Caudle

Aerospace Engineering

An electric aircraft propulsion test rig was designed and fabricated to predict thrust, torque and battery discharge profiles for an electric aircraft. The original unit was purchased from ElectraFlyer and included the DC brushless motor, carbon fiber propeller, charger, electronic controller and lithium polymer batteries. Various components were constructed and purchased in order to fabricate the optimal test rig apparatus. This apparatus allows for simultaneous measurement of the torque and thrust of the system through the use of a biaxial sensor. The test rig also measures system voltage and current, which allows the user to determine the discharge profile of …

Imu Integration To The Cal Poly Spacecraft Attitude Dynamics Simulator Power System, Wayland Chan

Electrical Engineering

The Cal Poly Spacecraft Attitude Dynamics Simulator mimics the rotation dynamics of a spacecraft in orbit and acts as a test bed for spacecraft attitude control system development and demonstration. Prior to this project, the simulator measured its attitude dynamics from a total of seven sensors mounted on to the platform, including three micro-electromechanical system (MEMs) gyroscopes, and four motor encoders. This project entails the installation of an LN-200 high performance gyroscope, which will provide a greater measure of accuracy. The goal of this project is to design a power circuit that will integrate the LN-200 inertial measurement unit onto …

Hybrid Rocket Based Combined Cycle Test Rig Design, Construction, And Testing, Mark Costa, Matthew Handfelt

Aerospace Engineering

No abstract provided.

Airplane Landing Flare-The Last 5 Seconds, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Electric Motor & Power Source Selection For Small Aircraft Propulsion, Jeremy Fehrenbacher, David L. Stanley, Mary E. Johnson Dr., Jeffrey Honchell

Purdue Polytechnic Directed Projects

The research conducted in this project is on electrical propulsion in aviation. A Cessna 172K aircraft with a Lycoming O-320-E2D piston engine serves as a baseline measurement. Investigation of the components required for electrical flight is performed, and components are selected based on market availability and operational performance criteria.

This research focuses on electrical propulsion in the aviation industry, and is tailored to aircraft within the General Aviation sector leading to the following research question: Can current electric motor and battery technologies conceptually support flight operations for a Cessna 172K in terms of aircraft performance criteria?

The results explore the …

Analysis Of Flow Migration In An Ultra-Compact Combustor, Brian T. Bohan

Theses and Dissertations

One of the major efforts for turbine engine research is to improve the thrust to weight of the system. One novel concept for accomplishing this is the use of an Ultra-Compact Combustor (UCC). The UCC attempts to shorten the overall combustion length (thereby reducing weight) by performing the combustion in the circumferential direction along the outside diameter of the core flowpath. One of the major benefits of this design is enhanced combustion due to the establishment of a high-g field in the circumferential cavity. AFIT and the Air Force Research Laboratory (AFRL) have been teamed for several years in understanding …

Compressor Performance Map Generation And Testing Per Sae J1723, Jeffrey Lee Freeman

Aerospace Engineering

A MATLAB program was written to plot compressor performance maps for a set of test data that was collected in accordance with SAE J1723 at Vortech Engineering, Inc. Paxton Automotive Corp.'s N2500 supercharger was used as a case example for the program, which was carried through from test stand installation to finalized compressor performance map. A sequence was also developed to interpolate the efficiency of the compressor for a given operational setting. The program was shown to be a great improvement from the previously applied technique for accomplishing the same tasks; it is more accurate in plotting the given data, …

Performance Characterization Of A Three-Axis Hall Effect Thruster, Spencer E. Temkin

Theses and Dissertations

No abstract provided.

Thermal Models For A 3 Cm Miniature Xenon Ion Thruster, Coleman Thomas Younger

Master's Theses

In order to support UCLA’s development of the 3 cm Miniature Xenon Ion (MiXI) thruster, Cal Poly has a 3 cm thruster under development. This version, called MiXI Cal Poly Version 1 (MiXI-CPv1), is complete and has been utilized in vacuum chamber thermal validation testing. Testing on this version was used to check the validity of heat transfer simulations modeled in SolidWorks. Investigations of the 3 cm ion thruster configuration were intended to discover the driving factors affecting the thermal behavior of the discharge chamber and surrounding design space.

Numerical simulations indicate that the heating of the samarium cobalt permanent …

Velocity Plume Profiles For Hall Thrusters Using Laser Diagnostic, Daniel B. Lee

Theses and Dissertations

This research built a non-intrusive laser diagnostic tool using Laser Induced Fluorescence (LIF) and absorption techniques to measure the velocity and density plume profiles of low powered Hall thrusters. This tool was then applied to a Busek 200W Hall thruster to validate the performance against previous research on the same thruster. A laser frequency sweep through 834.72 nm produced LIF signals for ionized xenon –collected at 541.9 nm – in the thruster plume and absorption data outside the plume at a neutral transition at 834.68 nm. The absorption data provided a baseline reference to calculate the axial and radially velocity …

Design, Fabrication, And Testing Of An Automotive Turbocharger-Based Gas Turbine Engine, John Kyle Thoma, Daniel Shehan, Benjamin Naravage, Jacob Melvin

Aerospace Engineering

A fully-functioning, self-sustaining gas turbine engine was designed and built. The engine was constructed around a Holset HE351 VGT automobile turbocharger, containing compressor and turbine assemblies on a common shaft. Other components of the engine were either purchased or designed and fabricated in-house. During initial testing of the completed engine, the turbocharger, however, was found to have extensive damage to the internal oil seals, and so the project could not be completed as planned. Instead, the combustor design and fabrication was completed for stand-alone testing. The combustion chamber was designed so that the flame tube could be easily changed out …