Aerodynamics and Fluid Mechanics Commons^™

An Optimization Study Of Small-Scale Propeller Blade, Fahad M. Nabid

Honors Undergraduate Theses

This research paper aims to investigate the optimization of smaller propeller blades to achieve maximum efficiency by studying the effect of the twist angle on reducing drag, increasing thrust, and preventing rapid wear on the blade. Inefficient propellers consume a significant amount of energy, particularly during low-speed flights. The low Reynolds number regime challenges aviation engineers to design propellers with the highest possible efficiency to minimize energy losses. The primary objective of this thesis is to optimize smaller propeller blade shapes to enable them to produce maximum efficiency. The advanced ratio of a propeller blade heavily influences the blade's performance …

The Development Of Computational Models For Melting-Solidification Applications Using The Volume-Of-Fluid Method, Brendon Cavainolo

Electronic Theses and Dissertations, 2020-2023

Fluids-related issues in the Aerospace industry are often multiphase in scope. Numerical modeling, such as computational fluid dynamics, is used to describe these problems, as they are difficult or impossible to describe analytically. This research uses computational fluid dynamics to describe multiphase problems related to melting-solidification and particle impingement. Firstly, a numerical model was established that uses the Volume-of-Fluid method to resolve a melting/solidifying particle. This model was verified against experiments and simplified analytical models, and a mesh independence study was done to ensure the results were independent of the mesh sizing. Next, the model was applied to two separate …

A Computational Fluid Dynamic Analysis Of Oxyacetylene Combustion Flow For Use In Material Response Boundary Conditions, Craig Meade

Theses and Dissertations--Mechanical and Aerospace Engineering

Oxyacetylene torches are used in the aerospace industry and research to test thermal protection system materials (TPS) due to their high flame temperatures and high heat flux capabilities. The purpose of this work is to determine a combustion model to accurately simulate the high temperature flow of an oxyacetylene torch. The flow conditions around a sample material can then be used as boundary conditions when modeling TPS material response. Two separate combustion models with equilibrium chemistry were investigated using ANSYS Fluent™; the Eddy-Dissipation Model, and the Partially Premixed model.The results of this study are compared to existing experiments for validation.

Stratospheric Glider Measurements Of Atmospheric Parameters, Anisa Haghighi

Theses and Dissertations--Mechanical and Aerospace Engineering

In June 2021 a series of high altitude flights were conducted in Spaceport America, NM, using a balloon launched Uncrewed Aircraft System (UAS) to assess its capability to conduct measurements of various atmospheric properties and study turbulence in the troposphere and lower stratosphere. This UAS descends using an automated flight trajectory. The instruments aboard included a NASA-developed infrasonic microphone to evaluate its remote turbulence detection capabilities and a five-hole probe capable of measuring the in situ wind vector. Also on board were temperature, humidity and wind profile sensors. This document focuses on the atmospheric properties measured at high altitudes, the …

Impact Of Spallation And Internal Radiation On Fibrous Ablative Materials, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles are equipped with Thermal Protection Systems (TPS) that encounter high heat rates and protect the payload while entering a planetary atmosphere. For most missions that interest NASA, ablative materials are used as TPS. These materials undergo several mass and energy transfer mechanisms to absorb intense heat. The size and construction of the TPS are based on the composition of the planetary atmosphere and the impact of various ablative mechanisms on the flow field and the material. Therefore, it is essential to quantify the rates of different ablative phenomena to model TPS accurately. In this work, the impact of …

Precision Meteorological Prediction Employing A Data-Driven, Adaptive, Real-Time (Dart) Approach, Sujit Sinha

Theses and Dissertations--Mechanical and Aerospace Engineering

The objective of this research is to improve precision meteorological prediction, benefiting both uncrewed aerial vehicle (UAV) operations by avoiding hazardous flight conditions and tracking contaminant or toxic clouds caused by incidents, accidents, or fires. The operational concept is to collect meteorological observations from instruments mounted on a swarm of UAVs, telemeter the data to a weather simulation model, revise the predicted solution by adapting the flow field to the observations, and then transmit the updated forecast to appropriate personnel as well as to the guidance system of UAVs for repositioning to the next set of most beneficial measurements. While …

Detonability Of A Rotating Detonation Combustor Seeded With Carbon/Hydrocarbon Particles At Fringe Operating Conditions, Matthew Hopwood

Electronic Theses and Dissertations, 2020-2023

The Rotating Detonation Combustor (RDC) has, in recent years, been a subject of great interest in the pressure-gain combustion research community. Researchers have been investigating the RDC as a potential improvement over current combustors in today's turbomachinery-based power generation systems. With the theoretical efficiency boost that detonations provide over deflagrating combustors, RDCs have the promise to be a next step in fuel/cost savings in the power generation industry. One mode of research to push an RDCs capabilities is the potential use of combustible carbon/hydrocarbon solid particles in addition to liquid or gaseous fuels. These particles are a source of high …

Heat Release And Flame Scale Effects On Turbulence Dynamics In Confined Premixed Flows, Max Fortin

Electronic Theses and Dissertations, 2020-2023

As industry transitions to a net-zero carbon future, turbulent premixed combustion will remain an integral process for power generating gas turbines and are also desired for aviation engines due to their ability to minimize pollutant emissions. However, accurately predicting the behavior of a turbulent reacting flow field remains a challenge. To better understand the dynamics of premixed reacting flows, this study experimentally investigates the evolution of turbulence in a high-speed bluff-body combustor. The combustor is operated across a range of equivalence ratios from 0.7-1 to quantify the role of heat release and flame scales on the evolution of turbulence as …

On The Simulation Of Supersonic Flame Holder Cavities With Openfoam, Zachary Chapman

Electronic Theses and Dissertations

One of the next major advancements in the aerospace industry will be hypersonic flight. However, to achieve hypersonic flight, propulsion systems capable of reaching hypersonic speeds need to be developed. One of the more promising hypersonic propulsion systems is the scramjet engine, however, several problems still need to be explored before reliable scramjet engines can be produced, the biggest being keeping the engine ignited. This has led to the use of flame holder cavities to create a region of subsonic flow within the engine to allow combustion to occur. High experimental costs make the use of computational fluid dynamic (CFD) …

Underwater Communication Acoustic Transducers: A Technology Review, Laila Shams, Tian-Bing Xu, Zhongqing Su (Ed.), Branko Glisic (Ed.), Maria Pina Limongelli (Ed.)

Mechanical & Aerospace Engineering Faculty Publications

This paper provides a comprehensive review on transducer technologies for underwater communications. The popularly used communication transducers, such as piezoelectric acoustic transducers, electromagnetic acoustic transducers, and acousto-optic devices are reviewed in detail. The reasons that common air communication technologies are invalid die to the differences between the media of air and water are addresses. Because of the abilities to overcome challenges the complexity of marine environments, piezoelectric acoustic transducers are playing the major underwater communication roles for science, surveillance, and Naval missions. The configuration and material properties of piezoelectric transducers effects on signal output power, beamwidth, amplitude, and other properties …

Probabilistic Short Term Solar Driver Forecasting With Neural Network Ensembles, Joshua Daniell

Graduate Theses, Dissertations, and Problem Reports (ETD)

Commonly utilized space weather indices and proxies drive predictive models for thermosphere density, directly impacting objects in low-Earth orbit (LEO) by influencing atmospheric drag forces. A set of solar proxies and indices (drivers), F_10.7, S_10.7, M_10.7, and Y_10.7, are created from a mixture of ground based radio observations and satellite instrument data. These solar drivers represent heating in various levels of the thermosphere and are used as inputs by the JB2008 empirical thermosphere density model. The United States Air Force (USAF) operational High Accuracy Satellite Drag Model (HASDM) relies on JB2008, and …

Design And Manufacture Of An Aerodynamic Body That Meets Scaling Law Requirements And Survives Severe G-Load Environment For Free-Flight Testing, Anthony R. Gonzalez

Graduate Theses, Dissertations, and Problem Reports (ETD)

Design and Manufacture of an Aerodynamic Body that Meets Scaling Law Requirements and Survives Severe G-load Environment for Free-Flight Testing

Anthony Gonzalez

Developing scale models to test functionality and ascertain aerodynamic properties is critical before manufacturing full-size products. Through dimensional analysis and similitude, engineers create scale models to test any parameter of interest. This research aims to design a scale model of an aerodynamic body for repeated free-flight testing. The Froude number is the dominant scale model law used to determine the geometric, mass, and inertia scaling laws. A critical requirement for this research is that the model should be …

Mitigation Of Aeroacoustic Noise Of A Fixed Wing Using Passive Flow Control, Cameron L. Perry

College of Graduate Studies: Theses & Dissertations

As the world becomes more environmentally conscious, noise pollution is of increasing concern. In this study, shallow dimples are applied to a NACA 0012 airfoil at multiple angles of attack (AoA) with the intent of reducing aeroacoustic noise emissions. Both Reynolds Averaged Navier-Stokes (RANS) and Large Eddy Simulation (LES) models are used for aerodynamic and aeroacoustic investigations, respectively, at a fixed Reynolds number of 4.8 x 10⁵. Altering the dimple depth to diameter ratio (d/D) from 2.5% to 15% is first investigated, with a d/D of 5% or lower resulting in the least aerodynamic impact. The transition from …

Initial Procedure For Small-Scale Extraction Of Subsurface Martian Ice, Evan Steers

Electronic Theses and Dissertations

For decades, NASA has been surveying the surface of Mars with plans for human exploration. Due to recent advancements, there is strong evidence to believe that frozen aquifers beneath the Martian surface hold great amounts of usable H2O. Since the discovery of water on Mars, NASA has expressed key interest in harvesting this valuable resource. The presence of usable H2O on Mars could reduce the launching mass of future missions by giving astronauts the capability to harvest water once they have landed on Mars. This research focuses on the optimization of a current design to extract Martian water and the …

Optimization Of Ported Cfd Kernels On Intel Data Center Gpu Max 1550 Using Oneapi Esimd, Mohammad Zubair, Aaron Walden, Gabriel Nastac, Eric Nielsen, Christoph Bauinger, Xiao Zhu

Computer Science Faculty Publications

We describe our experience porting FUN3D’s CUDA-optimized kernels to Intel oneAPI SYCL.We faced several challenges, including foremost the suboptimal performance of the oneAPI code on Intel’s new data center GPU. Suboptimal performance of the oneAPI code was due primarily to high register spills, memory latency, and poor vectorization. We addressed these issues by implementing the kernels using Intel oneAPI’s Explicit SIMD SYCL extension (ESIMD) API. The ESIMD API enables the writing of explicitly vectorized kernel code, gives more precise control over register usage and prefetching, and better handles thread divergence compared to SYCL. The ESIMD code outperforms the optimized SYCL …

Jet Noise Reduction: A Fresh Start, Christopher K. Tam, Fang Q. Hu

Mathematics & Statistics Faculty Publications

Attempts to reduce jet noise began some 70 years ago. In the literature, there have been many publications written on this topic. By now, it is common knowledge that jet noise consists of a number of components. They possess different spectral and radiation characteristics and are generated by different mechanisms. It appears then that one may aim at the suppression of the noise of a single component instead of trying to reduce jet noise overall. The objective of the present project is to reduce large turbulence structures noise. It is the most dominant noise component radiating in the downstream direction. …

Design And Validation Of An Aerodynamic System For A Formula Sae® Vehicle Using Vehicle Dynamic Simulation And Experimentation, Evan S. Cole

Graduate Theses, Dissertations, and Problem Reports (ETD)

This thesis presents the design, simulation, and experimental validation for the aerodynamic system for a Formula SAE® vehicle. The Society of Automotive Engineers ® (SAE) hosts a collegiate competition annually called Formula SAE® where students design, fabricate, and test a small “formula style” vehicle. The vehicle performs in relatively slow maneuvers, around different courses and tests to evaluate the vehicle’s overall performance. Over the years, collegiate teams have put significant research into the design and manufacturing of the aerodynamics of these vehicles. In order to justify this undertaking for future teams at West Virginia University’s Formula SAE® program, a comprehensive …

Induced Drag Laboratory Curriculum With Variable Aspect Ratio Wing, Alexander Milligan, Elizabeth Plyler

Williams Honors College, Honors Research Projects

A laboratory curriculum for undergraduate students at The University of Akron enrolled in 4600:413 Introduction to Aerodynamics was created to allow students a hands-on opportunity to study the basic fundamentals of aerodynamically induced drag. To accomplish this, a 3D printed wing was created with variable aspect ratio. This wing is to be utilized in the laboratory experiment in The University of Akron subsonic wind tunnel to generate data on lift on drag at different airspeeds, angles of attack, and aspect ratios. The laboratory curriculum provides basic theory applicable to the wind tunnel experiments as well as question prompts and data …

Design Of An Internal Osculating Waverider Intake, Mark E. Noftz, Andrew J. Shuck, Joseph S. Jewell, Jonathan Poggie, Andrew N. Bustard, Thomas J. Juliano, Nicholas J. Bisek

Publications

The design of an inward-turning, high-speed, three-dimensional streamline traced intake is presented from osculating axisymmetric theory. To satisfy the osculating intake design criteria, a stitched Busemann diffuser and Internal Conical Flow-A solution is used as the basic isentropic compressive streamline. This new contour provides efficient compression, high flow uniformity, and straight leading edge shocks of equal strength. Additionally, a novel method for constructing the inlet cowl is presented. The combined process leads to a new method of high-speed intake design. A generic shape-transitioned intake is constructed and named the Indiana Inlet for the Indiana universities that contributed to the project. …

Topologically Optimized Electrodes For Electroosmotic Actuation, Jianwen Sun, Jianyu Zhang, Ce Guan, Teng Zhou, Shizhi Qian, Yongbo Deng

Mechanical & Aerospace Engineering Faculty Publications

Electroosmosis is one of the most used actuation mechanisms for the microfluidics in the current active lab-on-chip devices. It is generated on the induced charged microchannel walls in contact with an electrolyte solution. Electrode distribution plays the key role on providing the external electric field for electroosmosis, and determines the performance of electroosmotic microfluidics. Therefore, this paper proposes a topology optimization approach for the electrodes of electroosmotic microfluidics, where the electrode layout on the microchannel wall can be determined to achieve designer desired microfluidic performance. This topology optimization is carried out by implementing the interpolation of electric insulation and electric …