Research On Force Compliance Of The Hydraulic Control System In Major-Motion Mechanism For Manipulator,
2020
1. Department of Mechanical and Electrical Engineering, Henan University of Science and Technology, Luoyang 471003, China;;
Research On Force Compliance Of The Hydraulic Control System In Major-Motion Mechanism For Manipulator, Geqiang Li, Jingwei Zhang, Yuesong Li, Bin Zhou, Shuye Ma
Journal of System Simulation
Abstract: The force compliance method of the hydraulic control system in major-motion mechanism was proposed during the forging process. Taking the major-motion mechanism of the forging manipulator as the target, the inverse kinematics model of major-motion mechanism was established, and the dynamic model of hydraulic control system was built. Through taking the pressure as the controlled variable, the model of the lifting hydraulic control system was obtained by using the co-simulation technology. Based on the principle of the horizontal buffering system, the model of the buffering hydraulic system which was made up of the buffering cylinder and the accumulator …
In-Cylinder Flow Analysis And Verification Of Opposed-Piston Two-Stroke Engine,
2020
1. School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081, China;;2. School of Mechanical and Power Engineering, North University of China, Taiyuan 030051, China;;
In-Cylinder Flow Analysis And Verification Of Opposed-Piston Two-Stroke Engine, Fukang Ma, Changlu Zhao, Zhenfeng Zhao, Wang Hao, Yu Xia, Cao Yan, Jiqing Zhang
Journal of System Simulation
Abstract: The effects of flat piston uniform scavenging chamber, flat piston non-uniform scavenging chamber and pit piston non-uniform scavenging chamber on the in-cylinder flow were analyzed. Uniflow scavenging zero-dimensional model was used to qualitative analysis in-cylinder flow organizational process and influence rule for opposed-piston two-stroke engine. Results show that uniform scavenging chamber can organize swirl and increase scavenging efficiency and non-uniform scavenging chamber can organize tumble and increase turbulent kinetic energy. Scheme 3 is favorable to organize tumble and maintain the in-cylinder turbulence intensity, which is increased by 150 percent.
Dfig Grid Connection Simulation Method Used For Transient Analysis Of Black-Start,
2020
1. State Key Laboratory of Alternate Electrical Power System With Renewable Energy Sources, Baoding 071003, China;;
Dfig Grid Connection Simulation Method Used For Transient Analysis Of Black-Start, Liqing Liu, Zengqiang Mi, Du Ping, Yuliang Wan, Yuan He
Journal of System Simulation
Abstract: Establishing a grid connection model of doubly-fed induction generator based wind turbine (DFIG) could be useful in the research and verification of black-start strategy in isolated power grid containing wind power. A DFIG grid connection simulation method based on Simulink was proposed. Through analyzing the operation characteristics of doubly-fed induction generator in no-load and grid-connected conditions, its dual-operation simulation model was established. According to the grid-connection theory of DFIG, the established doubly-fed induction generator model was combined with wind turbine, converter and other built-in modules, and the DFIG grid connection model was built with its control system added. …
Research On Intelligent Hauling Speed Regulation System Based On Shearer's Reliability,
2020
College of Mechanical Engineering, Liaoning Technical University, Fuxin 123000, China;
Research On Intelligent Hauling Speed Regulation System Based On Shearer's Reliability, Xunan Liu, Lijua Zhao, Dongmin Gai, Zhangyu Du, Liangying Hao
Journal of System Simulation
Abstract: Under the mine, Shearer's hauling speed affected the shearer's efficiency and reliability. Taking MG32570*2/325-BWD shearer as research object, from shearer's reliability, by using Simulink, the intelligent speed regulation system was established, based on shearer key parts' reliability. The building & simulation of hauling motor load torque block and recommended optimum hauling speed generation block which was fitted by neural network was solved. The simulation results show that: this system can achieve the recommended speed, which is traced by hauling speed rapidly and accurately. When consistent coefficient and cutting depth are 2.85 and 0.58m, the hauling motor's maximum speed is …
Eigen-Value Combination Approach For Speech Enhancement,
2020
1. College of Information Engineering, China Jiliang University, Hangzhou 310018, China;;
Eigen-Value Combination Approach For Speech Enhancement, Huijuan Lu, Yaqing Liu, Yanqiu Liu, Guan Wei
Journal of System Simulation
Abstract: In order to further suppress noise, a kind of speech enhancement algorithm based on Eigen-value merge was proposed. Eigen-values combination was used to improve the speech quality on the basis of the classic embedded pre-whitening subspace methods. The study shows that, after decomposing the covariance matrix of speech signals with noise, the larger Eigen-value component mainly includes speech information, and the smaller Eigen-value component mainly contains noise. Sorted by Eigen-values from small to big, the adjacent large Eigen-value component replaces with small Eigen-value component, which can effectively suppress noise and improve the quality of speech. Compared with other speech …
Gm-Cphd Filter With State-Dependent Clutter,
2020
School of Computer Science, Xi'an Polytechnic University, Xi'an 710048, China;
Gm-Cphd Filter With State-Dependent Clutter, Lili Ma, Xiaoshan Qin, Jinguang Chen
Journal of System Simulation
Abstract: For many sensors the clutters observed are easier to concentrate in the area around targets, namely the state-dependent clutter, which is different from the known clutter distribution in traditional filtering algorithms. So, the accuracy the real-time performance and of traditional multi-target tracking will be greatly degraded. To solve this problem, a kind of GM-CPHD filter with state-dependent clutter was proposed. The relationship between clutter and state was modeled. The clutter intensity was recalculated according to the distribution of clutter in the whole surveillance area and applied to update process; at the same time, in order to reduce the time …
Research On Static Behavior Of Xx-Joints Based On Ansys,
2020
1. College of Mechanical Engineering, Shanghai University of Engineering Science, Shanghai 201620, China;;
Research On Static Behavior Of Xx-Joints Based On Ansys, Pan Ying, Linxiao Qin
Journal of System Simulation
Abstract: Nonlinear finite element analysis was used in the ultimate bearing capacity on planar XX-joints by ANSYS software. The stress distributions of the joints were demonstrated, the main failure modes of the joints were determined, and the influences of some fundamental geometric parameters on the ultimate strength were the research points. The results show β (diameter ratio of the branch to the chord), θ (axial angle of the chord and the branch), γ (the ratio of the diameter of the chord to the thickness of the walls of the chord) are the main …
Research Of Impact Point Accuracy Of One-Dimensional Trajectory Correction Projectile Based On Monte Carlo,
2020
ZNDY of Ministerial Key Laboratory, NUST, Nanjing 210094, China;
Research Of Impact Point Accuracy Of One-Dimensional Trajectory Correction Projectile Based On Monte Carlo, Xiaoyun Lei, Zhian Zhang
Journal of System Simulation
Abstract: After the one-dimensional trajectory correction projectile out of the muzzle, various disturbance factors caused the impact point dispersion. Monte Carlo method was utilized on the shooting accuracy analysis. Based on the practical test datasets, three major factors were determined, namely, time delay of opening-damper mechanism, error of drag coefficient and measurement error of target. As to the disturbances, function randn was used for the analysis of the three major factors on the flat of Matlab. According to error distribution of the factors, the probability distribution and dispersion of the impact point were obtained. The maximum and minimum ranges of …
Potato Storage Temperature Prediction Control Based On Pso And Esns,
2020
1. Department of Electrical and Information, Xinjiang Institute of Engineering, Urumqi 830023, China;;2. School of Information Science and Engineering, Xinjiang University, Urumqi 830046 China;
Potato Storage Temperature Prediction Control Based On Pso And Esns, Junxia Liu, Xinrong Xiong, Hu Bing
Journal of System Simulation
Abstract: According to the current situation of potato storage and serious waste of raw materials and human resources of potato processing enterprises, combined with temperature data characteristics of potato storage from Xinjiang Great Russell Agricultural Science and Technology Development LTD., and control effect of the conventional control methods which is not ideal, a new temperature predictive control method was proposed, which rolled to optimize the input control variable by using particle swarm optimization algorithm and get the actual output values, use ESNs to forecast the temperature in the storage, the system was corrected by deviation between forecasting output and actual …
Attention Mechanism In Battlefield Situation Awareness,
2020
National Defense University, Beijing 100091, China;
Attention Mechanism In Battlefield Situation Awareness, Yisi Kong, Xiaofeng Hu, Zhu Feng, Jiuyang Tao
Journal of System Simulation
Abstract: Battlefield situation awareness (BSA) is the basis of C2 and decision making. Research on BSA can clarify the mechanism and lay the foundation for designing intelligent model and algorithm to assist commanders with situation awareness. Taking attention mechanism as the point, the relevant discussion in psychology was summarized, a framework of the attention mechanism in BSA was put forth, and its application in operational target value assessment was explored.
Adaptive Mutative Scale Chaos Particles Swarm Optimization Based On Logistic Mapping,
2020
College of Computer Science and Technology of Henan Polytechnic University, Jiaozuo 454000, China;
Adaptive Mutative Scale Chaos Particles Swarm Optimization Based On Logistic Mapping, Yanyang Zeng, Yunxia Feng, Wentao Zhao
Journal of System Simulation
Abstract: To overcome the shortcomings of Particle Swarm Optimization (PSO), an Adaptive Mutative Scale Chaos Particles Swarm Optimization (ACPSO) based on Logistic Mapping was proposed. The chaos method was used to initialize the particles. The adjustment method of the inertia weight depended on the particle's fitness; it could avoid premature convergence for the particles. When the particles fell into the local optimum, mutative scale chaos optimization strategy was adopted to adjust the optimal particles. To test the effectiveness of the algorithm, three representative algorithms were compared with. The results show that the algorithm has high convergence speed and high precision.
Target Combination Selection Optimization Method Of Joint Operations Based On Fuzzy Genetic Algorithm,
2020
The Department of Information Operation & Command Training, National Defense University, Beijing 100091, China;
Target Combination Selection Optimization Method Of Joint Operations Based On Fuzzy Genetic Algorithm, Suike Li, Jianhua Xiang, Haijun Wang, Mingzhi Zhang, Li Yi
Journal of System Simulation
Abstract: Under the condition of informatization, it is necessary to use intelligent model and optimization method to realize the cooperation and fusion of multi arms combat firepower. Aiming at the problem of target decision-making and firepower allocation in joint operations, the fuzzy multi-objective programming model was constructed to achieve the overall goal of achieving the maximum and the best firepower as a dual goal. In the model solving algorithm, the possibility theory was used to transform the fuzzy number, the model was transformed into the multi-objective programming model in the deterministic form. In order to improve the efficiency of …
Motion Reconstruction And Simulation Using Sparse Inertial Sensors,
2020
1. School of Software, Beijing Institute of Technology, Beijing 100081, China;;
Motion Reconstruction And Simulation Using Sparse Inertial Sensors, Lijun Cui, Tianyu Huang, Feng Feng, Zhang Jie, Yang Kai, Liu Dong
Journal of System Simulation
Abstract: A method was proposed to reconstruct high-dimensional full-body motion sequences from low-dimensional control data collected by sparse inertial sensors. The approach solved the mapping problem from low dimension to high dimension. A numerical similarity- geometrical similarity-time continuity model was setup to ensure the reconstructed motion candidates in numerical-logical similarity. The gap between angle and angular acceleration was eliminated by acceleration reconstruction. An energy function was introduced to optimize the reconstructed results which guaranteed the accuracy. The analysis and comparison experiments show that the proposed method can reconstruct nature and credible motions in real-time and can be applied …
Business Process Modeling Algorithm Based On Ontology Language,
2020
1. State Key Laboratory of Software Engineering, School of Computer, Wuhan University, Wuhan 430072, China;;2. Institute of Mathematical and Computer Sciences, Gannan Normal University, Ganzhou 341000, China;;
Business Process Modeling Algorithm Based On Ontology Language, Huang Ying, Kangshun Li, Li Wei, Keqing He
Journal of System Simulation
Abstract: In the view of problem in lack of information sharing mechanisms at the semantic level among processes, a business process modeling algorithm based on ontology language using concept hierarchy as background knowledge was proposed. The business process modeling by traditional business process languages can be transferred to ontology language (OWL) description so as to realize the semantic sharing of business process. The approach has two main advantages compared with traditional methods: (1) accelerating the building process, minimizing the conversion cost; (2) background knowledge guides the extraction of knowledge resided in database. As a way of validating the approach, part …
Measurement Error Correction Model Of Tof Depth Camera,
2020
Shanghai Key Laboratory of Power Station Automation Technology, School of Mechatronic Engineering and Automation, Shanghai University, Shanghai 200072, China;
Measurement Error Correction Model Of Tof Depth Camera, Le Wang, Luo Yu, Haikuan Wang, Minru Fei
Journal of System Simulation
Abstract: 3D data intuitively reflects the full view of the target or scene. Time of Flight (ToF) camera is a range imaging sensor that can provide 3D geometric information of targets immediately, thus it is widely applied in the robot positioning and navigation, 3D reconstruction and other aspects etc. Due to the operational principle of the camera itself, there are variety measurement errors of the source data obtained by ToF, resulting in image distortion. The measurement errors in the imaging process of ToF camera were analyzed and summarized, and the cubic spline interpolation method combined with look-up table was proposed …
Modeling Of Spectrum Sensing Energy Consumption In Cognitive Radio Networks,
2020
Faculty of Information Engineering and Automation, Kunming University of Science and Technology, Kunming 650500, China;
Modeling Of Spectrum Sensing Energy Consumption In Cognitive Radio Networks, Ziru Cui, Peng Yi
Journal of System Simulation
Abstract: In cognitive radio networks, the energy consumption in the process of spectrum sensing is the hot spot of research. A unified framework for modeling based on Poisson process was developed which could be used even under interference limited to count the energy consumption, thereby obtaining a spectrum sensing energy consumption. Spectrum sensing energy as the function of the number of secondary users in cognitive radio networks, their spatial density and the number of hops, could be modelled as a truncated gamma distribution. This model is used to statistically analyze cognitive users' energy consumption in the process of spectrum sensing …
Doa Estimation Method Of Uniform Circular Array Based On Improved Smoothed L0 Norm,
2020
School of Electronic and Information, Jiangsu University of Science and Technology, Zhenjiang 212003, China;
Doa Estimation Method Of Uniform Circular Array Based On Improved Smoothed L0 Norm, Wang Biao, Chen Feng, Lu Li
Journal of System Simulation
Abstract: To solve the problems of the narrow-band signal DOA method, such as low resolution and unsuitable for applications with small number of snapshot and array elements, etc, DOA of uniform circular array based on improved smoothed l0 norm was proposed after analysis of the characteristics of UCA model and signal airspace sparse, combining with improved the smooth l0 norm algorithm. For reconstructing the signal, the method used the combined continuous function as the approximation to l0 norm by sparse matrix processing array manifold, which improved the convergence speed. It was also extended to the UCA DOA …
Performance Evaluation Of Guidance And Control System Based On Improved Latin Hypercube,
2020
Control and Simulation Center, Harbin Institute of Technology, Harbin 150080, China;
Performance Evaluation Of Guidance And Control System Based On Improved Latin Hypercube, Denghui Zhang, Chao Tao, Songyan Wang, Ma Ping
Journal of System Simulation
Abstract: Aiming at the low efficiency and the poor space-filling property in the aircraft performance evaluation combined with simulation experiment, a novel aircraft performance evaluation method based on the improved LHD (Latin hypercube designs) was investigated. The six-DOF (Degree of Freedom) rigid aircraft model was built. Considering the characteristic of BTT (bank-to-turn) vehicle in dive phase, the performance evaluation index system of its guidance and control system was set up. The optimal LHD was applied to the performance evaluation of the aircraft guidance and control system. The improved algorithm can quickly construct a good design …
Best Viewpoint Selection For 3d Visualization Using Particle Swarm Optimization,
2020
College of Computer Science and Technology of Henan Polytechnic University, Jiaozuo 454000, China;
Best Viewpoint Selection For 3d Visualization Using Particle Swarm Optimization, Panpan Jia, Yanyang Zeng, Yunxia Feng
Journal of System Simulation
Abstract: The viewpoint selection is to automatically select one or more approximate optimal viewpoints in the viewpoints of multiple views, at the same time, it is related to the evaluation of the quality of the viewpoint. 3D visualization best viewpoint selection method based on particle swarm optimization algorithm was proposed. The viewpoint quality was evaluated by using the image information entropy and the image edge entropy, and the viewpoint was selected by the multi-objective intelligent optimization method. The basic flow begins with the initial viewpoint set, finding the best viewpoint by means of coding, particle evaluation, and particle update, which …
Sliding Mode Auto - Disturbance Rejection Control Of Hypersonic Vehicle Under Disturbance,
2020
1. School of Automation Science and Electrical Engineering, Beihang University, Beijing 100191, China;;2. State Key Laboratory of Virtual Reality Technology and Systems, Beihang University, Beijing 100191, China;;3. Key Laboratory of Aircraft Control Integration Technology, Beijing 100191, China;
Sliding Mode Auto - Disturbance Rejection Control Of Hypersonic Vehicle Under Disturbance, Mingzhi Cheng, Yunjie Wu, Ma Fei
Journal of System Simulation
Abstract: The strong coupling of the hypersonic vehicle, the high order of the model, and the perturbation of the aerodynamic parameters make it difficult for the general controller to achieve the desired control effect. The self-disturbing tandem technique can well meet the requirements of the high-order model control. The use of sliding mode variable structure technology which is not sensitive to perturbation of parameters can enhance the system immunity. The simulation results show that the control effect is very good.
