Power and Energy Commons^™

Designing Harvesting And Hauling Cost Models For Energy Cane Production For Biorefineries, Prabodh Illukpitiya, Firuz Yuldashev, Kabirat Nasiru

Agricultural and Environmental Sciences Faculty Research

The harvesting and hauling operations of bioenergy feedstock is an important area in biofuel production. Production costs can be minimized by maintaining optimal machinery units for these operations. The objective of this study is to design an optimal harvesting unit for bioenergy refinery and estimate harvesting and hauling costs of energy cane. A biorefinery with the annual capacity of processing twenty-five million imp. gallons of ethanol were considered. Given the efficiency of harvesting, a two-row soldier system was considered. Considering the year-round supply of energy cane to the refinery, the optimal machinery unit was designed, and the combined operation costs …

Development Of A Configurable Real-Time Event Detection Framework For Power Systems Using Swarm Intelligence Optimization, Umar Farooq

Dissertations and Theses

Modern power systems characterized by complex topologies require accurate situational awareness to maintain an adequate level of reliability. Since they are large and spread over wide geographical areas, occurrence of failures is inevitable in power systems. Various generation and transmission disturbances give rise to a mismatch between generation and demand, which manifest as frequency events. These events can take the form of negligible frequency deviations or more severe emergencies that can precipitate cascading outages, depending on the severity of the disturbance and efficacy of remedial action schema. The impacts of such events have become more critical with recent decline in …

Adaptive Balancing Compensation In Distribution Grid Of Ultra High-Power Manufacturing Plants, Motab Almousa

LSU Doctoral Dissertations

This dissertation presents a method of adaptive compensation, capable of handling power factor and the supply quality improvement under non-sinusoidal conditions. The focus in this dissertation is put on developing compensation for ultra-high power metallurgical plants, meaning on compensation in three-phase, four-wire ultra-high power dynamic, distribution systems. A separate attention in the dissertation is put on the adaptive compensation of ultrahigh power arc furnaces. The dissertation also presents an original method of adaptive compensation of DC current generated by such arc furnaces.

The proposed compensator is developed in the frame of the Currents’ Physical Components (CPC) – based power theory. …

Modeling And Analysing The Impact Of Heat Pump Water Heaters On Distribution Systems Using Gridlab-D, Midrar Adham

Dissertations and Theses

With the constant increase in energy demand, finding ways to reduce peak load and the energy-costs factors has become more imperative. Domestic water heating showcases a significant opportunity for such applications. Water heating is the second-highest energy consumer in the residential sector across the United States. Electric Water Heaters (EWHs), in particular, constitute nearly 43% of American household water heating energy consumption. Heat Pump Water Heater (HPWH), on the other hand, is an advanced water heating technology that has recently emerged in the United States residential market.

The objectives of this work are to develop a HPWH model and build …

New Solid Polymer Electrolytes For Lithium, Sodium, And Calcium-Based Batteries, Francielli Silva Genier

Dissertations - ALL

The establishment of sustainable energy sources highly depends on efficient storage devices to guarantee a consistent power supply. The growing demand for lithium-ion batteries (LIBs) for this purpose, combined with concerns about lithium availability, has motivated the search for viable storage alternatives, such as sodium and calcium. While several studies have investigated different lithium-free liquid electrolytes, the transport of these alternative ions in their polymer counterparts remains understudied. The advantages of solid polymer electrolytes include the possibility of higher energy density in solid-state devices and the elimination of safety concerns associated with liquid electrolytes, such as flammability, leakage, and dendrite …

Renewable Energy Microgrids To Improve Electrification Rate In Democratic Republic Of Congo: Case Of Hydro, Municipal Waste And Solar, Ngondo Otshwe Josue, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, it is imperative for citizens to have access to electricity. This applies to Congolese--rural and urban dwellers, and if possible, it should be guaranteed by government’s laws and policies. Howev er, the rural and urban areas of Democratic Republic of Congo (DRC) suffer majorly from lack of access to electricity. The major reasons are the high costs associated with connection to the national central grid and production insufficiency. Therefore, one feasible approach to electrify these areas is to use microgrids. This technolo gy is decent and viable option for energy revolution since it incorpo rates energy storage systems, distributed …

Assessment Of Energy Efficiency In Beverage Industry, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

The brewery industry has a significant contribution to the national income. However, it is also associated with energy intensive processes and pollution. In this work, the energy efficiency assessment of the largest brewery in Tanzania i.e., Tanzania Breweries Limited has been conducted. Energy consumption analysis was conducted according to IEEE SA 739 1995. Important parameters used to assess brewery energy efficiency were boiler efficiency and losses, equipment energy productivity as well as load factor. It was found that the main energy consumers are packaging (54.63%), brewing (29.30%) and utilities (15.17%). More importantly, it was found that about 68% of the …

A Model For Sustainable Adoption Of Solar Photovoltaic Technology In Tanzania, Joseph Kihedu

Tanzania Journal of Engineering and Technology (TJET)

The aim of the study was to develop a sustainable model for enhancement of the solar PV technology adoption in Tanzania. The model was developed based on the identified barriers that hinder the adoption of solar PV technology and adopted the best strategies from successful projects. Further, the drivers and activities were developed based on selected best strategies from successful projects. The identified barriers to the adoption of solar PV technology, which are grouped into five associated categories and their significances, are lack of access to finance (32%), non-enforcement of policy and regulation (31%), technical (18%), lack of awareness (9%) …

An Experimental Approach Towards Pv-Based Solar System Sizing For An Engineering Laboratory, Muyideen O. Lawal

Tanzania Journal of Engineering and Technology (TJET)

This study aims at providing an experimental sizing procedure for a rooftop PV-based solar power system for an engineering laboratory. This was achieved by monitoring the peak power and energy delivered by an installed 20W solar panel into an 18 Ah battery. Knowledge of the average daily peak power and energy was used to determine the percentage rated capacity available for use and the sun hour. A load consumption comparison was also carried out with and without the connection of a load to inverter. In addition to this, the monitoring of the no-load consumption of the inverter was carried out. …

Viability Analysis Of Ubungo Ii Gas Power Plant Efficiency Improvement Using Co-Generation System, Aviti Thadei Mushi

Tanzania Journal of Engineering and Technology (TJET)

The power utility, Tanzania Electric Supply Company Limited (TANESCO) is faced with challenges of supplying adequate power to the ever-increasing demand. To this end, this paper explores the installed Ubungo Gas Power Plant (UGP II) located in Dar es Salaam to find means of utilizing it in co-generation method. The study embarked on detailed modelling of the system and run simulations which indicated that the co-generation can result to power generation efficiency increase between 10.42 to 50.92%. It is recommended to change the UGP II to exploit this co-generation method. Further, the study could be improved by including more parameters …

Study On Low Voltage Electrodeposition Of Diamond-Like Carbon Film, Li Wang, Min-Xian Wu, Jun Li, Yan-Li Chen, Wen-Chang Wang, Zhi-Dong Chen

Journal of Electrochemistry

Diamond-like carbon (DLC) films are receiving a lot of attention from the scientific community, thanks to the promise of DLC films for applications in microelectronics and optoelectronics. Usually, electrodeposition is the preferred common technique because of low cost, large deposition area and simplicity of the setup. However, when carbon films are electrodeposited on a stainless steel, high cell voltages (≥1000 V) are required owing to the low electric conductivity of the organic solvents. This work has developed a new electrolyte system that could achieve carbon deposition on a stainless steel under a low applied cell voltage. The DLC films were …

Effect Of Sodium Alcohol Thiyl Propane Sulfonate On Electrolysis Of High Performance Copper Foil For Lithium Ion Batteries, Sen Yang, Wen-Chang Wang, Ran Zhang, Shui-Ping Qin, Min-Xian Wu, Naotoshi Mitsuzaki, Zhi-Dong Chen

Journal of Electrochemistry

Electrolytic copper foils have been widely used in printed circuit boards and lithium-ion batteries due to their simple production process and high economic value. In the process of electrolysis foil making, additives can greatly improve the performance of electrolytic copper foils. In this work, the copper foils were prepared in a self-designed plate electrodeposition device of which the operating principles were in accordance with those of actual industrial production. A series of the Virgin Make-up Solution (VMS: 312.5 g·L^-1 CuSO₄·5H₂O, 100 g·L^-1 H₂SO₄, 50 mg·L^-1 Cl^-) containing …

Modified Q-Learning Method For Automatic Voltage Regulation In Wide-Area Multigeneration Systems, Brook Abegaz, Sina Zarrabian

Engineering Science Faculty Publications

The state-estimation and optimal control of multigeneration systems are challenging for wide-area systems having numerous distributed automatic voltage regulators (AVR). This paper proposes a modified Q-learning method and algorithm that aim to improve the convergence of the approach and enhance the dynamic response and stability of the terminal voltage of multiple generators in the experimental Western System Coordinating Council (WSCC) and large-scale IEEE 39-bus test systems. The large-scale experimental testbed consists of a six-area, 39-bus system having ten generators that are connected to ten AVRs. The implementation shows promising results in providing stable terminal voltage profiles and other system parameters …

Monofacial Vs Bifacial Solar Photovoltaic Systems In Snowy Environments, Koami Soulemane Hayibo, Aliaksei Petsiuk, Pierce Mayville, Laura Brown, Joshua M. Pearce

Electrical and Computer Engineering Publications

There has been a recent surge in interest in the more accurate snow loss estimates for solar photovoltaic (PV) systems as large-scale deployments move into northern latitudes. Preliminary results show bifacial modules may clear snow faster than monofacial PV. This study analyzes snow losses on these two types of systems using empirical hourly data including energy, solar irradiation and albedo, and open-source image processing methods from images of the arrays in a northern environment in the winter. Projection transformations based on reference anchor points and snowless ground truth images provide reliable masking and optical distortion correction with fixed surveillance cameras. …

Sunsation’S Solar Powered Picnic Table, Michelle M. Barnett, Christopher Barber, Casey Durham, David Mason

Mechanical Engineering

Team SunSation is an interdisciplinary senior design project group that was tasked with developing a semi-permanent seating area for Cal Poly's electrical engineering courtyard. The EE courtyard is populated with plastic folding tables and chairs that are slowly falling apart. Dale Dolan, the head of the EE department, requested that a table design be developed that incorporates the use of solar panels. The addition of the solar panels to the table would help promote clean renewable energy as well as provide shade to those sitting in the courtyard.

The solution that SunSation arrived at is broken up into mechanical/structural, electrical, …

Smart Usb-C Wall Plug For The Dc House Project, Ridge Lahti, Dino Maslic

Electrical Engineering

DC operated devices and appliances powered by AC systems suffer inefficiencies resulting from the losses of converting AC energy into DC energy. At Cal Poly, the DC House Project aims to minimize the need for AC electricity in homes and encourage the use of renewable energy systems. The DC House uses a 48V DC bus that must be stepped down for use with increasing number of DC loads in a typical home. In this project, a Smart USB-C Wall Plug is designed to work with USB Power Delivery to provide a variable voltage output for use with these DC loads …

Developing A Miniature Smart Boat For Marine Research, Michael Isaac Eirinberg

Computer Engineering

This project examines the development of a smart boat which could serve as a possible marine research apparatus. The smart boat consists of a miniature vessel containing a low-cost microcontroller to live stream a camera feed, GPS telemetry, and compass data through its own WiFi access point. The smart boat also has the potential for autonomous navigation. My project captivated the interest of several members of California Polytechnic State University, San Luis Obispo’s (Cal Poly SLO) Marine Science Department faculty, who proposed a variety of fascinating and valuable smart boat applications.

Solar Solution For Mini-Rover, Michaella Ochotorena, Derick Louie, Jonathan Cederquist, Collin Petersen, Cole Korchek

Mechanical Engineering

This project focuses on designing, building, and testing a functional prototype of a collapsible solar array on the mini Mars rover being developed by client and sponsor, Mr. Rich Murray. Although many previous collapsible solar arrays have been deployed for space missions, the previous solar-powered Mars rovers only deployed their arrays once upon landing. This solar array will be able to collapse and deploy multiple times to allow for greater rover mobility and stability when the rover is not charging. This system is critical to the success of the rover project because it provides power without which the rover cannot …

Total Sky Imager Project, Ryan D. Maier, Benjamin Jack Forest, Kyle X. Mcgrath

Mechanical Engineering

Solar farms like the Gold Tree Solar Farm at Cal Poly San Luis Obispo have difficulty delivering a consistent level of power output. Cloudy days can trigger a significant drop in the utility of a farm’s solar panels, and an unexpected loss of power from the farm could potentially unbalance the electrical grid. Being able to predict these power output drops in advance could provide valuable time to prepare a grid and keep it stable. Furthermore, with modern data analysis methods such as machine learning, these predictions are becoming more and more accurate – given a sufficient data set. The …

Multifamily Complex Smart Locks For Property Management And Tenant Security, April Mills, Allen Chen, Dana Kumamoto, Michael Cook

Mechanical Engineering

Maintaining and managing hundreds of locks and physical keys for an apartment complex can be time consuming and costly, especially when the apartments turn over to new tenants. Our goal was to develop a smart door lock that is compatible with Obodo’s management app for apartment complexes to make accessing apartments secure and simpler for tenants and easier to manage for owners.

We designed and manufactured one smart door lock that is powered with four AA batteries and utilizes a dynamic NFC device and Bluetooth technology. The board can enter a sleep mode which reduces power consumption. The dynamic NFC …

Behavior, Switching Losses, And Efficiency Enhancement Potentials Of 1200 V Sic Power Devices For Hard-Switched Power Converters, Ali Mahmoud Salman Al-Bayati, Mohammad Abdul Matin

Electrical and Computer Engineering: Faculty Scholarship

Semiconductor power devices are the major constituents of any power conversion system. These systems are faced by many circumscriptions due to the operating constraints of silicon (Si) based semiconductors under certain conditions. The emergence and persistence evolution of wide bandgap technology pledge to transcend the restrictions imposed by Si based semiconductors. This paper presents a thorough experimental study and assessment of the performance of three power devices: 1200 V SiC cascode, 1200 V SiC MOSFET, and 1200 V Si IGBT under the same hardware setup. The study aims to capture the major attributes for each power device toward determining their …

Skip The Grid: Giving Power To Navajo Nation, Ryan J. Schacherbauer

Construction Management

Skip the Grid is a project organized by Heart of America, a nonprofit, looking to improve the education and overall wellbeing of children and their families. Many residents within Navajo Nation do not have access to continuous power and rely on temporary generators or car battery to obtain any kind of electricity. Heart of America partnered with the Red Mesa School District to identify families that did not have power, which was impacting the children’s ability to complete their online schoolwork. This senior project was comprised of an interdisciplinary team responsible for installing a working solar system on twelve homes …

Controlling Temperature Of Dc-Dc Converter Using Switching Frequency Adjustment, Sajjad Ahsan, Arsalan Mughal, Mark Rapiz

Electrical Engineering

As DC-DC converter operates under different load conditions, the amount of loss within the converter varies accordingly. Consequently the temperature of the DC-DC converter will also change based on the load demand. For PWM based DC-DC converters, one factor that contributes to the loss; thus, the increase in temperature is the switching frequency at which the converter operates. The higher the switching frequency used, the bigger the switching loss and in turn the hotter the converter. In this project, the temperature of a DC-DC converter is controlled by changing the switching frequency used by the converter. The hardware investigation used …

Hybrid Ac/Dc Light Bulb, Celina Mendez, Kristian Vincent Cruz, Nouman Baryal

Electrical Engineering

A hybrid AC/DC house aims to maximize the use of AC electricity from the utility grid and DC electricity from renewable energy sources such as roof-top solar panels. The hybrid system will therefore improve the reliability of the electrical by enabling power to be delivered to the loads even when one of the sources is not operational. One of the critical loads that every house needs is lighting. The hybrid AC/DC system should therefore be reliably facilitating the power delivery to the lighting. In this project, a localized hybrid AC/DC for LED light bulbs is designed and constructed. The hybrid …

Hybrid Ac/Dc House: The Road To A Sustainable Future, Nicholas Mcadams, Luis Rodriguez

Electrical Engineering

The Hybrid AC/DC house is a sustainable alternative to preexisting residential power systems. The implementation of a DC bus in current homes will allow inefficient DC-AC and AC-DC conversions to be circumvented. This provides a direct path for current to flow to DC loads from DC sources such as solar panels to minimize power losses. In doing so, this will give users the ability to power their homes strictly from renewable sources and substantially decrease reliance on the utility. For this purpose, the hybrid AC/DC house is also designed in such a way to be entirely grid-independent to provide power …

Microgrid Energy Storage Branch, Evan Luu, Jeffrey Shieh

Electrical Engineering

The microgrid is the future for the electrical utility system. Because of this, future power engineers need to be well-versed in this topic when they go into industry. Cal Poly has created a microgrid laboratory for this very purpose. However, it is missing its battery based energy storage branch. Due to safety concerns, a traditional chemical battery is not suitable for student use. In order to maintain Cal Poly’s learn-by-doing approach, an alternative solution must be implemented. A regenerative power supply meets the criteria for student use. It is capable of simulating the sinking and sourcing capabilities of a battery …

Baker/Koob Final Report: Solar Solution For Mini Mars Rover, Jonathan Cederquist, Cole Korchek, Derick Louie, Michaella Ochotorena, Collin Petersen

Mechanical Engineering

This project focused on designing, building, and testing a functional prototype of a collapsible solar array on the mini Mars rover being developed by client and sponsor, Mr. Rich Murray. Although many previous collapsible solar arrays have been deployed for space missions, the previous solar-powered Mars rovers only deployed their arrays once upon landing. This solar array will be able to collapse and deploy multiple times to allow for greater rover mobility and stability when the rover is not charging. This system is critical to the success of the rover project because it provides power without which the rover cannot …

Current-Source Dc-Dc Converter For Fiber-Optic Communication Systems, Jissell C. Jose

Master's Theses

In this thesis, a proof of concept for a current-source DC-DC converter for powering sensors used in an underwater communications system is presented. The proposed converter steps down an input current of 0.9 A to 0.625 A, while maintaining an output voltage of 24 V and output power of 15 W. The complete steady-state analysis and design of the proposed converter in its single-stage form is also explained in detail. Performance evaluation of the proposed converter was carried out using LTspice. Results of the simulation demonstrate that the design was able to produce average output current of 0.639 A at …

Reliability Study Of Electrical Distribution System With Local And Interregional Bidirectional Centralized Electric Vehicle Charging Stations, Janine Gian Christii C. Darato

Master's Theses

In this thesis, a method was developed to evaluate the impact of bidirectional electric vehicle (EV) charging on power system reliability using Synergi Electric software. Load profiles, EV availability, EV state-of-charge (SOC) were important factors considered in this study. The analysis in this study is based on local and interregional vehicle-to-grid (V2G) implementation at different load points in the system. In general, local V2G implementation is observed to be more effective in improving system reliability over interregional V2G power flow. System Average Interruption Duration Index (SAIDI) and System Average Interruption Frequency Index (SAIFI) improvements were observed to increase with increasing …

Microgrid Laboratory Wind Energy Integration, Vincent Liang

Master's Theses

Cal Poly San Luis Obispo’s Electrical Engineering Department and the Power Energy Institute have developed a microgrid laboratory with various generators, loads, and protection systems over the past several years. To improve and make the Cal Poly microgrid laboratory more realistic, this thesis outlines the process of improving the EE microgrid setup by adding a wind energy generation system via an induction generator, excitation capacitors, and a protection relay. By adding an induction generator, the microgrid system becomes more resilient to sudden power fluctuations by maintaining a stable voltage and frequency when the microgrid is islanded. To test this, a …