Open Access. Powered by Scholars. Published by Universities.®

Electronic Devices and Semiconductor Manufacturing Commons™

Open Access. Powered by Scholars. Published by Universities.®

Series

Discipline
Institution
Keyword
Publication Year
Publication
File Type

Articles 181 - 198 of 198

Full-Text Articles in Electronic Devices and Semiconductor Manufacturing

Cualse² Thin Films Obtained By Chalcogenization, S. Marsillac, K. Benchouk, C. El Moctar, J. C. Bernède, J. Pouzet, A Khellil, M. Jamali Jan 1997

Cualse² Thin Films Obtained By Chalcogenization, S. Marsillac, K. Benchouk, C. El Moctar, J. C. Bernède, J. Pouzet, A Khellil, M. Jamali

Electrical & Computer Engineering Faculty Publications

CuAlSe2 thin films have been synthesized by chalcogenization of thin Cu and Al layers sequentially deposited by evaporation under vacuum. It is shown that CuAlSe2 films are obtained with some Cu2-δSe and Se phases present at the surface. These surface phases are suppressed by annealing under vacuum and by chemical etching in a KCN solution. At the end of the process, the XRD spectrum demonstrates that textured CuAlSe2 films have been obtained with preferential orientation of the crystallites along the (112) direction. The gap of the films is 2.7 eV as expected. The …

Go to article

A Stochastic Model For Crystal-Amorphous Transition In Low Temperature Molecular Beam Epitaxial Si(111), R. Venkatasubramanian, Suresh Gorantla, S. Muthuvenkatraman, Donald L. Dorsey Dec 1996

A Stochastic Model For Crystal-Amorphous Transition In Low Temperature Molecular Beam Epitaxial Si(111), R. Venkatasubramanian, Suresh Gorantla, S. Muthuvenkatraman, Donald L. Dorsey

Electrical & Computer Engineering Faculty Research

Molecular beam epitaxial Si (111) grown below a certain temperature result in amorphous structure due to the limited surface mobility of atoms in finding correct epitaxial sites. In spite of many experimental and theoretical studies, the mechanism of crystal‐amorphous transition and its dynamics related to the growth conditions are not well understood. In this article, we present a theoretical model based on the formation of stacking fault like defects as a precursor to the amorphous transition of the layer. The model is simulated based on a stochastic model approach and the results are compared to that of experiments for temperatures …

Go to article

Nlo Waveguide "And" Switch And Method Therefor, John J. Kester, Iyad A. Dajani, Peter M. Ranon, Thomas G. Alley Sep 1996

Nlo Waveguide "And" Switch And Method Therefor, John J. Kester, Iyad A. Dajani, Peter M. Ranon, Thomas G. Alley

AFIT Patents

Method and apparatus are provided for NLO switching by first providing a phase-matched SHG grating which outputs a reinforced SHG beam only when two input beams of frequency (ω) are present in two modes of such wg. The so encoded NLO switch is operated by directing at least two input pulsed laser beams of frequency (ω) into the two modes of the wg to generate a reinforced pulsed output SHG beam and output same from the wg in an NLO switching process. The two input beams desirably have a separate pulse train and the spatial and temporal overlap of the …

Go to article

A Self-Consistent Numerical Method For Simulation Of Quantum Transport In High Electron Mobility Transistor; Part 1: The Boltzmann-Poisson-Schrodinger Solver, Rahim Khoie Jan 1996

A Self-Consistent Numerical Method For Simulation Of Quantum Transport In High Electron Mobility Transistor; Part 1: The Boltzmann-Poisson-Schrodinger Solver, Rahim Khoie

Electrical & Computer Engineering Faculty Research

A self-consistent Boltzmann-Poisson-Schrödinger solver for High Electron Mobility Transistor is presented. The quantization of electrons in the quantum well normal to the heterojunction is taken into account by solving the two higher moments of Boltzmann equation along with the Schrödinger and Poisson equations, self-consistently. The Boltzmann transport equation in the form of a current continuity equation and an energy balance equation are solved to obtain the transient and steady-state transport behavior. The numerical instability problems associated with the simulator are presented, and the criteria for smooth convergence of the solutions are discussed. The current-voltage characteristics, transconductance, gate capacitance, and unity-gain …

Go to article

A Self-Consistent Numerical Method For Simulation Of Quantum Transport In High Electron Mobility Transistor; Part Ii: The Full Quantum Transport, Rahim Khoie Jan 1996

A Self-Consistent Numerical Method For Simulation Of Quantum Transport In High Electron Mobility Transistor; Part Ii: The Full Quantum Transport, Rahim Khoie

Electrical & Computer Engineering Faculty Research

In Part I of this paper we reported a self-consistent Boltzmann-Schrodinger-Poisson simulator for HEMT in which only electrons in the first subband were assumed to be quantized with their motion restricted to 2 dimensions. In that model, the electrons in the second and higher subbands were treated as bulk system behaving as a 3 dimensional electron gas. In Part II of this paper, we extend our simulator to a self-consistent full-quantum model in which the electrons in the second subband are also treated as quantized 2 dimensional gas. In this model, we consider the electrons in the lowest two subbands …

Go to article

Scanning-Tunneling-Microscopy Study Of Pb On Si(111), D. Tang, H. E. Elsayed-Ali, J. Wendelken, J. Xu Jan 1995

Scanning-Tunneling-Microscopy Study Of Pb On Si(111), D. Tang, H. E. Elsayed-Ali, J. Wendelken, J. Xu

Electrical & Computer Engineering Faculty Publications

Scanning-tunneling microscopy has been used to study temperature and coverage dependence of the structure of lead on the Si(111)-7×7 surface. For low Pb coverage, the Pb atoms favored the faulted sites. The ratio between the number of Pb atoms on faulted to unfaulted sites increased after sample annealing. An energy difference of 0.05 eV associated with a Pb atom on these two sites is estimated. The mobility of Pb atoms on Si(111) was observed at a temperature as low as 260°C for a coverage of 0.1 and 1 ML. © 1995 The American Physical Society.

Go to article

Broadband Rf Current Detector, George Cabrera Nov 1994

Broadband Rf Current Detector, George Cabrera

FIU Electronic Theses and Dissertations

The problems to be solved in this thesis were 1) development of a broadband RF preamplifier to be used with non-ferrous current probes so that the amplified signal exceeds the errors due to cable pickup, no detection is needed in this application, and 2) development of a self-contained device that amplifies and detects the output from a nonferrous current probe, providing a digital readout of the current. These instruments have been completed and are being tested for use by the National Institutes of Occupational Safety and Health (NIOSH). The self-contained current meter operates at frequencies up to 600 MHz, and …

Go to article

Temporal Development Of Electric Field Structures In Photoconductive Gaas Switches, K. H. Schoenbach, J. S. Kenney, F.E. Peterkin, R. J. Allen Jan 1993

Temporal Development Of Electric Field Structures In Photoconductive Gaas Switches, K. H. Schoenbach, J. S. Kenney, F.E. Peterkin, R. J. Allen

Bioelectrics Publications

The temporal development of the electric field distribution in semi‐insulating GaAs photoconductive switches operated in the linear and lock‐on mode has been studied. The field structure was obtained by recording a change in the absorption pattern of the switch due to the Franz–Keldysh effect at a wavelength near the band edge of GaAs. In the linear mode, a high field layer develops at the cathode contact after laser activation. With increasing applied voltage, domainlike structures become visible in the anode region and the switch transits into the lock‐on state, a permanent filamentary electrical discharge. Calibration measurements show the field intensity …

Go to article

Novel Chemical Preparative Route For Semiconducting Mose2 Thin Films, K. C. Mandal, O. Savadogo Jan 1991

Novel Chemical Preparative Route For Semiconducting Mose2 Thin Films, K. C. Mandal, O. Savadogo

Faculty Publications

No abstract provided.

Go to article

Influence Of Copper Doping On The Performance Of Optically Controlled Gaas Switches, St. T. Ko, V. K. Lakdawala, K. H. Schoenbach, M. S. Mazzola Jan 1990

Influence Of Copper Doping On The Performance Of Optically Controlled Gaas Switches, St. T. Ko, V. K. Lakdawala, K. H. Schoenbach, M. S. Mazzola

Electrical & Computer Engineering Faculty Publications

The influence of the copper concentration in silicon-doped gallium arsenide on the photoionization and photoquenching of charge carriers was studied both experimentally and theoretically. The studies indicate that the compensation ratio (NCu/NSi) is an important parameter for the GaAs:Si:Cu switch systems with regard to the turn-on and turn-off performance. The optimum copper concentration for the use of GaAs:Si:Cu as an optically controlled closing and opening switch is determined.

Go to article

Nanosecond Optical Quenching Of Photoconductivity In A Bulk Gaas Switch, M. S. Mazzola, K. H. Schoenbach, V. K. Lakdawala, S. T. Ko Jan 1989

Nanosecond Optical Quenching Of Photoconductivity In A Bulk Gaas Switch, M. S. Mazzola, K. H. Schoenbach, V. K. Lakdawala, S. T. Ko

Electrical & Computer Engineering Faculty Publications

Persistent photoconductivity in copper-compensated, silicon-doped semi-insulating gallium arsenide with a time constant as large as 30 µs has been excited by sub-band-gap laser radiation of photon energy greater than 1 eV. This photoconductivity has been quenched on a nanosecond time scale by laser radiation of photon energy less than 1 eV. The proven ability to turn the switch conductance on and off on command, and to scale the switch to high power could make this semiconductor material the basis of an optically controlled pulsed-power closing and opening switch.

Go to article

Gaas Photoconductive Closing Switches With High Dark Resistance And Microsecond Conductivity Decay, M. S. Mazzola, K. H. Schoenbach, V. K. Lakdawala, R. Germer, G. M. Loubriel, F. J. Zutavern Jan 1989

Gaas Photoconductive Closing Switches With High Dark Resistance And Microsecond Conductivity Decay, M. S. Mazzola, K. H. Schoenbach, V. K. Lakdawala, R. Germer, G. M. Loubriel, F. J. Zutavern

Electrical & Computer Engineering Faculty Publications

Silicon-doped n-type gallium arsenide crystals, compensated with diffused copper, were studied with respect to their application as photoconductive, high-power closing switches. The attractive features of GaAs:Cu switches are their high dark resistivity, their efficient activation with Nd:YAG laser radiation, and their microsecond conductivity decay time constant. In the authors' experiment, electric fields are high as 19 kV/cm were switched, and current densities of up to 10 kA/cm2 were conducted through a closely compensated crystal. At field strengths greater than approximately 10 kV/cm, a voltage `lock-on' effect was observed.

Go to article

A Bulk Optically Controlled Semiconductor Switch, Rudolf K.F. Germer, Karl H. Schoenbach, Stephen G.E. Pronko Jan 1988

A Bulk Optically Controlled Semiconductor Switch, Rudolf K.F. Germer, Karl H. Schoenbach, Stephen G.E. Pronko

Bioelectrics Publications

Turn‐on and turn‐off of bulk semiconductor switches, based on excitation and quenching of photoconductivity, respectively, have been demonstrated with copper‐doped II‐VI semiconductor crystals. The increase of the conductivity (turn‐on) was realized with a xenon flash‐lamp pulse of 15‐μs duration. A reduction of the conductivity (turn‐off) was obtained by irradiating the samples with IR light using an 8‐ns Nd:YAG laser pulse (YAG denotes yttrium aluminum garnet). For turn‐on in CdS:Cu the conductivity follows the xenon flash excitation. The turn‐off time constant was 250 ns. ZnS and ZnSe crystals showed a slower response. A memory effect for the IR light was observed.

Go to article

An Optically Controlled Closing And Opening Semiconductor Switch, K. H. Schoenbach, V. K. Lakdawala, R. Germer, S. T. Ko Jan 1988

An Optically Controlled Closing And Opening Semiconductor Switch, K. H. Schoenbach, V. K. Lakdawala, R. Germer, S. T. Ko

Electrical & Computer Engineering Faculty Publications

A concept for a bulk semiconductor switch is presented, where the conductivity is increased and reduced, respectively, through illumination with light of different wavelengths. The increase in conductivity is accomplished by electron ionization from deep centers and generation of bound holes. The reduction of conductivity is obtained by hole ionization from the excited centers and subsequent recombination of free electrons and holes. The transient behavior of electron and hole density in a high power semiconductor (GaAs:Cu) switch is computed by means of a rate equation model. Changes in conductivity by five orders of magnitude can be obtained.

Go to article

Evidence For Amphoteric Behavior Of Ru On Cdte Surfaces, D. N. Bose, S. Basu, K. C. Mandal, D. Mazumdar Feb 1986

Evidence For Amphoteric Behavior Of Ru On Cdte Surfaces, D. N. Bose, S. Basu, K. C. Mandal, D. Mazumdar

Faculty Publications

No abstract provided.

Go to article

Electrical And Structural Properties Of P-N Junctions In Cw Laser Annealed Silicon, M. Maier, D. Bimberg, G. Fernholz, H. Baumgart, F. Phillipp Jan 1982

Electrical And Structural Properties Of P-N Junctions In Cw Laser Annealed Silicon, M. Maier, D. Bimberg, G. Fernholz, H. Baumgart, F. Phillipp

Electrical & Computer Engineering Faculty Publications

Depth profiles of the electrical quality of ion implanted and cw laser annealed p-n junctions in silicon are obtained for the first time by secondary ion mass spectroscopy. A comparison with the crystallographic properties of the surface and the junction as observed by Nomarski optical microscopy as well as cross-sectional and plan view transmission electron microscopy is made. Samples containing slip dislocations show better insulation and a lower reverse bias current across the p-n junction as compared to samples with a perfect surface in agreement with current-voltage characteristics. Small dislocation loops located at the junction are found to degrade the …

Go to article

Photo And Magnetic Gated Bi-Directional Counter, Charles Burdette Kraemer May 1972

Photo And Magnetic Gated Bi-Directional Counter, Charles Burdette Kraemer

Graduate Research Papers

The purpose of this study is to investigate digital counter circuitry, digital logic, and some special applications of digital display systems. The technical data and information ascertained from the research will be used to design and develop a four-digital counter with photo and magnetic gated inputs.

Go to article

Evolution Of The Dynamo, Ralph Nelson Soule Jan 1900

Evolution Of The Dynamo, Ralph Nelson Soule

Student and Lippitt Prize essays

This essay supplies an extensive history of electricity beginning in 600 BC to 1900, chronicling the evolution of the dynamo and its uses.

Go to article

First Prev