Electronic Devices and Semiconductor Manufacturing Commons^™

Evaluation Of The Transport Properties Of Gasb For Bipolar Applications Through Monte Carlo Simulations, Damayanthi Palaniappan

Electrical & Computer Engineering Theses & Dissertations

GaAs is currently the semiconductor material of choice for high speed, low power applications. Its electronic transport properties are superior to almost all other semiconductors. It is also used in a variety of bipolar applications such as photodetectors and photo-mixers. However, as is well known, the hole mobility and related transport parameters of GaAs are not very good. This is a serious drawback, and poses a potential problem for all applications involving bipolar conductivity. In order to increase the high :frequency limits and high-speed capability of bipolar devices, the choice of an alternative material, therefore, becomes necessary. An important first …

Réalisation De Couches Minces De Cualse² Par Recuit De Feuilllets Superposés Cu/Al/Se/Al…, Étude De Conditions De Dépôt, C.O. El Moctar, S. Marsillac, J. C. Bernede, A. Conan, K. Benchouk, A. Khelil

Electrical & Computer Engineering Faculty Publications

Thin layers of Cu/Al/Se/Al/Cu/Al/Se/…/Al/Se sequentially deposited have been annealed half an hour at 855 K. CuAlSe₂ thin films crystallized in the chalcopyrite structure are obtained. The films being contaminated by oxygen, the experimental deposition conditions of the aluminum layer have been improved in order to decrease the atomic concentration of oxygen below 5 at%. Such results can be obtained in vacuum of 10^-4 Pa, when the aluminum deposition rate is 1 nm/s and when the layer is immediately covered after deposition. Films obtained in such a way are nearly stoichiometric with lattice parameters in accordance with the expected …

Time-Resolved Reflection High-Energy Electron Diffraction Study Of The Ge(111)-C(2×8)-(1×1) Phase Transition, Xinglin Zeng, Bo Lin, Ibrahim El-Kholy, Hani E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

The dynamics of the Ge(111)-c(2×8)-(1×1) phase transition is investigated by 100-ps time-resolved reflection high-energy electron diffraction. A laser pulse heats the surface while a synchronized electron pulse is used to obtain the surface diffraction pattern. Slow heating shows that the adatoms in Ge(111)-c(2×8) start to disorder at ∼510 K and are converted to a disordered adatom arrangement at 573 K. For heating with 100-ps laser pulses, the Ge(111)-c(2×8) reconstructed adatom arrangement starts to disorder at 584±16K, well above the onset temperature of ∼510 K for the disordering of Ge(111)-c(2×8) observed for slow …

Atomic Hydrogen Cleaning Of Inp(100) For Preparation Of A Negative Electron Affinity Photocathode, K. A. Elamrawi, M. A. Hafez, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Atomic hydrogen cleaning is used to clean InP(100) negative electron affinity photocathodes. Reflection high-energy electron diffraction patterns of reconstructed, phosphorus-stabilized, InP(100) surfaces are obtained after cleaning at ∼400 °C. These surfaces produce high quantum efficiency photocathodes (∼8.5%), in response to 632.8 nm light. Without atomic hydrogen cleaning, activation of InP to negative electron affinity requires heating to ∼530 °C. At this high temperature, phosphorus evaporates preferentially and a rough surface is obtained. These surfaces produce low quantum efficiency photocathodes (∼0.1%). The use of reflection high-energy electron diffraction to measure the thickness of the deposited cesium layer during activation by correlating …

Cualse² Thin Films Obtained By Chalcogenization, S. Marsillac, K. Benchouk, C. El Moctar, J. C. Bernède, J. Pouzet, A Khellil, M. Jamali

Electrical & Computer Engineering Faculty Publications

CuAlSe₂ thin films have been synthesized by chalcogenization of thin Cu and Al layers sequentially deposited by evaporation under vacuum. It is shown that CuAlSe₂ films are obtained with some Cu₂-_δSe and Se phases present at the surface. These surface phases are suppressed by annealing under vacuum and by chemical etching in a KCN solution. At the end of the process, the XRD spectrum demonstrates that textured CuAlSe₂ films have been obtained with preferential orientation of the crystallites along the (112) direction. The gap of the films is 2.7 eV as expected. The …

Two-Dimensional Drift-Diffusion Simulations Of Silicon Avalanche Shaper (Sas) Devices For High Power Applications, Hamid Jalali

Electrical & Computer Engineering Theses & Dissertations

Silicon Avalanche Shaper devices have been projected as being important components of an inexpensive, semiconductor-based technology for high power switching applications. The primary advantage of this technology is that it is based on Silicon material which is easy to fabricate and has a well established processing technology. Unlike other high power technologies, the SAS devices do not rely on external optical triggering which eliminates the need for lasers and related optical circuitry.

The SAS based high power switching technology has been pioneered and tested by a Russian group. Though preliminary results have been very encouraging, the device reliability and its …

Electron Beam Emission From A Ferroelectric Cathode, Crystal Briana Garland

Electrical & Computer Engineering Theses & Dissertations

The electron beam emission from a LTZ-2 (lead titanate-zirconate) ferroelectric cathode was characterized. The purpose was to determine the operation range for this type of electron emitter. The experimental apparatus consisted of a high voltage driving circuit with a charging voltage up to 30kV. A solid-state SCR switch is used to generate the high voltage pulse which induces a polarization change. Current densities on the order of 80A/cm² 30kV were achieved. The electron beam profile is Guassian. At long anode-cathode distances the measured current densities were found to be above Child-Langmuir space charge limits. The large current densities and …

Wavelength Modulation Spectroscopy With Diode Lasers, Ying Lu

Electrical & Computer Engineering Theses & Dissertations

Wavelength Modulation Spectroscopy is a non-intrusive technique which enables several parameters such as concentration, velocity, and temperature of a target specie to be measured. The method involves a modulation of a probe laser beam and detection at the fundamental, or any harmonic frequency, by a phase-sensitive apparatus. The theory of wavelength modulation is discussed. Effects of the finite value of the wavelength modulation index, together with the effects of any residual amplitude modulation that often occurs simultaneously in a diode laser, are included. It is shown that there are several advantages in using detection harmonics orders greater than the second. …

Scanning-Tunneling-Microscopy Study Of Pb On Si(111), D. Tang, H. E. Elsayed-Ali, J. Wendelken, J. Xu

Electrical & Computer Engineering Faculty Publications

Scanning-tunneling microscopy has been used to study temperature and coverage dependence of the structure of lead on the Si(111)-7×7 surface. For low Pb coverage, the Pb atoms favored the faulted sites. The ratio between the number of Pb atoms on faulted to unfaulted sites increased after sample annealing. An energy difference of 0.05 eV associated with a Pb atom on these two sites is estimated. The mobility of Pb atoms on Si(111) was observed at a temperature as low as 260°C for a coverage of 0.1 and 1 ML. © 1995 The American Physical Society.

The Current Voltage Characteristics Of Electron Beam Controlled Thin Film Diamond Switches, Christopher Anthony Molina

Electrical & Computer Engineering Theses & Dissertations

The dark current of natural diamond thin films and the induced current due to electron-beam irradiation was measured up to a range of 7000Ncm'. The contact material was aluminum, annealed and unannealed. Switching experiments were performed with electron energies ranging from 70keV to 172keV. The switching results obtained are strongly dependent on the biasing polarity, incident electron energy, and whether the contact is blocking or Ohmic in nature. A simple model which takes traps into consideration allows us to explain the various switching responses. The range of electrons which define, in part, the switch mode was measured for one sample …

Transient Simulations And Modelling Of Semi-Insulating Gaas Photoconductive Switches, Prasun Kumar Raha

Electrical & Computer Engineering Theses & Dissertations

The primary objective of this thesis is to develop a one-dimensional transient simulator for Photoconductive Semiconductor Switches (PCSS) taking into consideration the material characteristics, the internal physical effects, and the external circuit. Simulations have been performed to study the device behavior at different voltage levels for copper-doped silicon-compensated GaAs material, though other materials could easily be simulated by changing the parameters. The model includes hole transport, and the results demonstrate the effect of hole injection, with and without recombination centers. In addition to developing a one-dimensional transient simulator, the role of various physical effects, such as the field-dependence of trapping …

Optimization Of Electron-Beam Activated Gaas Switches, Raymond Jack Allen Iii

Electrical & Computer Engineering Theses & Dissertations

The use of electron induced luminescence (cathodoluminescence) in gallium arsenide offers the possibility to modulate the conductance of the material on a timescale of nanoseconds and with a pulse rate of MHz, through modulation of an electron-beam current. This ionization mechanism allows the utilization of semi-insulating GaAs in fast, high power closing and opening switches. The efficiency of the switches is determined by the hold-off voltage of the GaAs switches, and by the conversion efficiency of electron energy into (useful) photon energy. Studies of the dark-current and the electron-beam induced conductance in semi-insulating GaAs have been performed in order to …

Absorption Imaging Studies On Intrinsic Gaas, John Samuel Kenney

Electrical & Computer Engineering Theses & Dissertations

A diagnostic technique has been developed which allows recording of the temporal and spatial development of electric field structures in GaAs photoconductive switches. The optical method is based on the Franz-Keldysh effect. Measurements were performed with a Nd:YAG activation laser and a GaAs laser diode as the probe laser. At low applied voltages a 100 atm wide region of high electric field is seen at the cathode only. With increasing voltage strong domain like structures emerge at the anode also. A calibration measurement shows that the electric fields in these domains are well above 50 kV/cm. At a threshold voltage, …

Temporal Development Of Electric Field Structures In Photoconductive Gaas Switches, K. H. Schoenbach, J. S. Kenney, F.E. Peterkin, R. J. Allen

Bioelectrics Publications

The temporal development of the electric field distribution in semi‐insulating GaAs photoconductive switches operated in the linear and lock‐on mode has been studied. The field structure was obtained by recording a change in the absorption pattern of the switch due to the Franz–Keldysh effect at a wavelength near the band edge of GaAs. In the linear mode, a high field layer develops at the cathode contact after laser activation. With increasing applied voltage, domainlike structures become visible in the anode region and the switch transits into the lock‐on state, a permanent filamentary electrical discharge. Calibration measurements show the field intensity …

The Effect Of Contacts On The Performance Of Electron-Beam Controlled Gaas And Diamond Switches, Michael Kevin Kennedy

Electrical & Computer Engineering Theses & Dissertations

The performance of GaAs and diamond as electron-beam controlled closing and opening switches has been studied. An emphasis has been placed on the effect of contacts on the current-voltage characteristics. The two materials studied were GaAs and diamond. Using the same semi-insulating GaAs wafer as a source of material, a bulk device and a p-i-n device have been fabricated and compared. The asymmetry of the pin diode allows operation at higher voltage because of the ability to suppress the lock-on effect. Whereas GaAs was ionized through cathodoluminescence; diamond, in the form of thin films, has been directly ionized by the …

A Novel Technique For Deep Level Characterization Of High-Resistivity Semiconductor Materials, Sridhar Panigrahi

Electrical & Computer Engineering Theses & Dissertations

An improved photo induced current transient spectroscopy (PICTS) technique is developed for studying deep level parameters in high-resistivity semiconductor materials. A new digital data acquisition approach and improvement in the cryogenics of the system have enabled us, for the first time in our laboratory, to detect CuA level in a copper doped silicon compensated gallium arsenide (GaAs:Si:Cu) sample. The digital approach improves both the signal to noise ratio (S/N) and the efficiency of the system. Also, multiple PICTS spectra in a single thermal cycle can be obtained. In the present work, various doped and undoped gallium arsenide ( GaAs) and …

Study Of Cathodoluminescence In Semiconductors, Mandakini V. Kale

Electrical & Computer Engineering Theses & Dissertations

Cathodoluminescence in Zn doped GaAs and ZnSe, the materials of interest for electron-beam controlled semiconductor switches, has been investigated. A new diagnostic technique, using telescopic setup of lenses, was developed to study the spatially resolved cathodoluminescence. The setup eliminated the light, other than rays from the sample, parallel to the optical axis, resulting in an enhanced spatial resolution. At high e-beam energies, light was detected, from the Zn layer region in the GaAs. It is proposed to be due to the radiative recombination of electron-hole pairs, created by the e-beam. For the polycrystalline ZnSe no light emission was detected. This …

Cathodoluminescence Of Gaas, Tyler Smith

Electrical & Computer Engineering Theses & Dissertations

Cathodoluminescence of band-gap radiation across the bulk of a proposed semiconductor switch has been studied. Such a device relies on the efficient use of cathodoluminescence to modulate the conductivity of the switch. Diagnostics were configured to measure the intensity of band-gap radiation across the bulk of several switch samples. The measured results were compared to calculations based on a four energy level band-gap model which included two deep levels EL2 and HL10.

Q Improvement Of A 5.2 Ghz Te011 Cavity By Incorporating Y1Ba2Cu3O7-X, R. Joseph Leclear

Electrical & Computer Engineering Theses & Dissertations

Research is undertaken to apply high temperature superconducting material to improve the quality factor (Q) of a 5.2 GHz cylindrical resonant cavity. In particular, the approach is to electrophoretically deposit polycrystalline Y₁Ba₂Cu₃O_7-x (YBCO) on the conducting surface of the cavity cylinder. Spalling of the YBCO ceramic coating due to expansion and contraction of the cavity during sintering and testing is overcome by segmenting the cylinder. Results show that the Q of the cavity is increased over that of a copper cavity at temperatures below 60 K. At 20 K, improvement exceeds a factor …

Monte Carlo Simulation Of Millimeter-Wave Gunn Effect Oscillators, Ramani Vaidyanathan

Electrical & Computer Engineering Theses & Dissertations

Monte Carlo simulations have been carried out to investigate the performance of microwave Gunn oscillators. Three separate aspects of the simulation problem have been comprehensively addressed in this work. First, the presence of an external circuit has been self-consistently incorporated into the calculations. The inclusion of the external circuit facilitates a study of the circuit controlled regime, and correctly models effects arising from the time dependent boundary conditions. Secondly, microscopic details of the electronic relaxation mechanisms which ultimately control the frequency response limits, have been taken into account through an iterative Monte Carlo-Poisson scheme. This procedure overcomes a potential shortcoming …

Optical And High Electric Field Effects In Bulk Gallium Arsenide Switches, Randy Roush

Electrical & Computer Engineering Theses & Dissertations

During the past few years, bulk, photoconductive switching has become recognized as a viable topic for future research on moderate and high power switches. The two-pulse, or BOSS, concept relies on an excitation laser pulse, and a separate de-excitation pulse in conjunction with silicon doped, copper compensated, GaAs to create a variable temporal electrical pulse width. The research contained in this document provides information concerning the feasibility of the BOSS concept, as the switch is scaled to larger sizes, and higher voltage and current. The major concern will be the high voltage and current effects. The absorption length for 1064 …

Deep Level Characterization Studies In Gaas, Gordhan R. Barevadia

Electrical & Computer Engineering Theses & Dissertations

The goal of this research was to investigate deep levels in different types of GaAs, a material for high power optically controlled bulk semiconductor switches. For low resistivity semiconductors, such as silicon doped GaAs material (p =0.054 Ω cm), deep level transient spectroscopy (DLTS) was used to characterize deep levels. Three deep levels (EL6, EL3, and EL2) have been detected in this material. For high resistivity semiconductors (p > 10⁴ Ω cm), difficulty of electrical carrier injection and of making a junction does not permit the use of DLTS technique. Therefore, an experimental set-up of the photo-induced current transient spectroscopy …

Analysis And Development Of A Switched Capacitor Power Supply, John Richard Hackworth

Electrical & Computer Engineering Theses & Dissertations

The combination of a switched capacitor network and switching power supply techniques can result in a transformer less regulated DC power supply that is small, relatively simple, and efficient. In addition, the output of such a system could be operated over a wide range of common mode voltages. Multiple switched capacitor supplies could be stacked to achieve voltage multiplication.

Although the output of a system of this type is a continuous function, the internal operation must be analyzed in finite time elements. This numerical analysis will be shown in both a mathematical approach and a computer model.

Hydrogenation Effects On Trap Related Conduction In Diamond, Linwood Cleveland Watkins Iii

Electrical & Computer Engineering Theses & Dissertations

In this research work, the results of an experimental investigation on the electrical conduction mechanism in type Ιa and Ilb diamonds are presented. These results are compared with those of previous theoretical studies. The basic physical properties of diamond are discussed. Details of ohmic contact formation on diamond are presented.

The current-voltage characteristics revealed the presence of traps located below the Fermi level. The unfilled trap density was determined. The deep traps were further studied using spectroscopic photoconductivity measurements and the trap energy levels were determined.

The effects of hydrogenation on trap related conduction were studied subsequently. Hydrogenation was carried …

Influence Of Copper Doping On The Performance Of Optically Controlled Gaas Switches, St. T. Ko, V. K. Lakdawala, K. H. Schoenbach, M. S. Mazzola

Electrical & Computer Engineering Faculty Publications

The influence of the copper concentration in silicon-doped gallium arsenide on the photoionization and photoquenching of charge carriers was studied both experimentally and theoretically. The studies indicate that the compensation ratio (N_Cu/N_Si) is an important parameter for the GaAs:Si:Cu switch systems with regard to the turn-on and turn-off performance. The optimum copper concentration for the use of GaAs:Si:Cu as an optically controlled closing and opening switch is determined.

The Electrical Characteristics Of Semi-Insulating Gallium Arsenide A Material For High Power Switches, David Clifton Stoudt

Electrical & Computer Engineering Theses & Dissertations

An experimental study of the electrical characteristics of semi-insulating gallium arsenide has been performed. The goal of this research was to aid in the development of an electron-beam controlled high-power semiconductor switch. The electrical characteristics were found to be heavily dependent on the deep level configuration of the material being investigated. Two methods of deep level characterization are discussed and their results are compared to the information given by the material manufacturer. Studies were conducted to determine both the steady-state and transient dark current characteristics of the switch. Along with being a function of the applied voltage and the deep …

Study Of Direct Semiconductor Materials For An Optically Controlled Switch, Sung Taek Ko

Electrical & Computer Engineering Theses & Dissertations

A model for a bulk GaAs photoconductive switch has been developed and solved to determine the performance of the device in closing and opening switch applications. The GaAs material has been characterized by deep level transient spectroscopy (DLTS). Two electron traps (EL2 and EL5) and one hole trap (Cu_B} have been detected and were included in the model. Simulation studies are performed on several GaAs switch systems composed of different combinations and density of deep levels to investigate the influence of deep traps in a photoconductive switch system. The electron occupancy of each deep trap is traced in …

Gaas Photoconductive Closing Switches With High Dark Resistance And Microsecond Conductivity Decay, M. S. Mazzola, K. H. Schoenbach, V. K. Lakdawala, R. Germer, G. M. Loubriel, F. J. Zutavern

Electrical & Computer Engineering Faculty Publications

Silicon-doped n-type gallium arsenide crystals, compensated with diffused copper, were studied with respect to their application as photoconductive, high-power closing switches. The attractive features of GaAs:Cu switches are their high dark resistivity, their efficient activation with Nd:YAG laser radiation, and their microsecond conductivity decay time constant. In the authors' experiment, electric fields are high as 19 kV/cm were switched, and current densities of up to 10 kA/cm² were conducted through a closely compensated crystal. At field strengths greater than approximately 10 kV/cm, a voltage `lock-on' effect was observed.

Nanosecond Optical Quenching Of Photoconductivity In A Bulk Gaas Switch, M. S. Mazzola, K. H. Schoenbach, V. K. Lakdawala, S. T. Ko

Electrical & Computer Engineering Faculty Publications

Persistent photoconductivity in copper-compensated, silicon-doped semi-insulating gallium arsenide with a time constant as large as 30 µs has been excited by sub-band-gap laser radiation of photon energy greater than 1 eV. This photoconductivity has been quenched on a nanosecond time scale by laser radiation of photon energy less than 1 eV. The proven ability to turn the switch conductance on and off on command, and to scale the switch to high power could make this semiconductor material the basis of an optically controlled pulsed-power closing and opening switch.

A Bulk Optically Controlled Semiconductor Switch, Rudolf K.F. Germer, Karl H. Schoenbach, Stephen G.E. Pronko

Bioelectrics Publications

Turn‐on and turn‐off of bulk semiconductor switches, based on excitation and quenching of photoconductivity, respectively, have been demonstrated with copper‐doped II‐VI semiconductor crystals. The increase of the conductivity (turn‐on) was realized with a xenon flash‐lamp pulse of 15‐μs duration. A reduction of the conductivity (turn‐off) was obtained by irradiating the samples with IR light using an 8‐ns Nd:YAG laser pulse (YAG denotes yttrium aluminum garnet). For turn‐on in CdS:Cu the conductivity follows the xenon flash excitation. The turn‐off time constant was 250 ns. ZnS and ZnSe crystals showed a slower response. A memory effect for the IR light was observed.