Model Development And Assessment Of The Gate Network In A High-Performance Sic Power Module, William Austin Curbow

Graduate Theses and Dissertations

The main objective of this effort is to determine points of weakness in the gate network of a high-performance SiC power module and to offer remedies to these issues to increase the overall performance, robustness, and reliability of the technology. In order to accomplish this goal, a highly accurate model of the gate network is developed through three methods of parameter extraction: calculation, simulation, and measurement. A SPICE model of the gate network is developed to analyze four electrical issues in a high-speed, SiC-based power module including the necessary internal gate resistance for damping under-voltage and over-voltage transients, the disparity …

Synchrophasor-Based Fault Location Detection And Classification, In Power Systems, Using Artificial Intelligence, Hemal Falak

Graduate Theses and Dissertations

With the introduction of sophisticated electronic gadgets which cannot sustain interruption in the provision of electricity, the need to supply uninterrupted and reliable power supply, to the consumers, has become a crucial factor in the present-day world. Therefore, it is customary to correctly identify fault locations in an electrical power network, in order to rectify faults and restore power supply in the minimum possible time. Many automated fault location detection algorithms have been proposed, however, prior art requires topological and physical information of the electrical power network. This thesis presents a new method of detecting fault locations, in transmission as …

Optical And Electrical Analysis Of Zno/Znte Micropillar Solar Cells, Sadia Binte Sohid

Master’s Theses

The prime focus of the energy-research community in recent times has been replacing fossil fuels with renewable energy. Therefore, photovoltaic research areas are rapidly expanding in this era. The purpose of this work is to compare three different structural ZnO/ZnTe solar cell types (planar, axial micropillar and radial micropillar). The best optical and electrical performance has been obtained by the radial junction (core-shell) ZnO/ZnTe micropillar solar cell due to its pillar structure and radial junction. The unique advantage of the radial junction micropillar is that the angle of the incident light and the carrier collection is orthogonal. Therefore, the pillar …

Investigation Of A Gan-Based Power Supply Topology Utilizing Solid State Transformer For Low Power Applications, Akrem Mohamed Elrajoubi

Graduate Theses and Dissertations

Gallium nitride (GaN) power devices exhibit a much lower gate capacitance for a similar on-resistance than its silicon counterparts, making it highly desirable for high-frequency operation in switching converters, which leads to their significant benefits on power density, cost, and system volume. High-density switching converters are being realized with GaN power devices due to their high switching speeds that reduce the size of energy-storage circuit components. The purpose of this dissertation research is to investigate a new isolated GaN AC/DC switching converter based on solid-state transformer configuration with a totem-pole power factor corrector (PFC) front-end, a half-bridge series-resonant converter (SRC) …

Comparative Study Of Power Semiconductor Devices In A Multilevel Cascaded H-Bridge Inverter, Kenneth Mordi

Graduate Theses and Dissertations

This thesis compares the performance of a nine-level transformerless cascaded H-bridge (CHB) inverter with integrated battery energy storage system (BESS) using SiC power MOSFETs and Si IGBTs. Two crucial performance drivers for inverter applications are power loss and efficiency. Both of these are investigated in this thesis. Power devices with similar voltage and current ratings are used in the same inverter topology, and the performance of each device is analyzed with respect to switching frequency and operating temperature. The loss measurements and characteristics within the inverter are discussed. The Saber® simulation software was used for the comparisons. The power MOSFET …

Hybrid Perovskite Characterization And Device Applications., Kasun Fernando

Electronic Theses and Dissertations

Hybrid perovskites are a group of materials that has shown a great impact in the field of scientific research in the past decade due to the efficiency gain within a short period of time. Hot casting is one technique that has been producing high efficient and stable solar cells. Electrical transportation of lateral device structure by such film is explored to understand basic properties and predict possible device applications using it. Under dark, memristive ability of the film was explored using various experiments. Unique uni-polar memristor ability was observed. Using the experimental results, a model is hypothesized using the concepts …

Increasing The Longevity Of Tungsten Filaments In A Zone Refiner, Byron D. Greenlee

Senior Theses

Zone refining is used for its ability to purify material and grow single crystals. To produce these single crystals, a suspended molten zone, generated by electron bombardment, passes along the polycrystalline stock. During a zone refining run, the filaments that produce the electron bombardment can fail. In this project, the longevity of tungsten filaments in a zone refiner was investigated. A new bombardment geometry was constructed to attempt to increase the longevity of the filaments. The new geometry had a shield machined into it to prevent line-of-sight impurities originating in the molten zone from striking the filaments. It was found …

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

College of Graduate Studies: Theses & Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …

Flexible Custom Electric Skateboard, Caleb Adam Kelsay

Electrical Engineering

At Cal Poly traveling long distances only accessible by foot such as across campus or from the car park to class can be tiring and time-consuming. While not physically demanding, the trek consumes time in our tight college life schedule. To improve our time efficiency this project provides a relatively lightweight, powered solution to quickly and effectively travel long distances while maintaining full control and safety even on hills, a current limitation of traditional skateboards.

This electric skateboard includes the battery capacity to travel all around campus on a single charge with a compact and flexible skateboard design that provides …

The Development Of Novel Interconnection Technologies For 3d Packaging Of Wire Bondless Silicon Carbide Power Modules, Sayan Seal

Graduate Theses and Dissertations

This dissertation advances the cause for the 3D packaging and integration of silicon carbide power modules. 3D wire bondless approaches adopted for enhancing the performance of silicon power modules were surveyed, and their merits were assessed to serve as a vision for the future of SiC power packaging. Current efforts pursuing 3D wire bondless SiC power modules were investigated, and the concept for a novel SiC power module was discussed. This highly-integrated SiC power module was assessed for feasibility, with a focus on achieving ultralow parasitic inductances in the critical switching loops. This will enable higher switching frequencies, leading to …

Integration Of Thin Film Tpv Cells To Cvd Diamond Heat Spreaders, Emma J. Renteria

Electrical and Computer Engineering ETDs

In this work, techniques to isolate thermophotovoltaic (TPV) devices from the growth substrate and their subsequent integration with Chemical Vapor Deposition (CVD) diamond heat spreaders will be discussed, with the envisioned goal of fabricating thermally managed cells. CVD diamond heat spreaders are a great option for thermal management of TPV cells. The key requirement, however, is the bonding of the TPV cell directly onto the diamond wafer without the presence of thick (>350 μm) growth substrates, which can offer significant thermal resistance.

The first approach is to release GaSb epitaxial layers from GaSb substrates. However, this is challenging due …

Design Of Dc-Link Vscf Ac Electrical Power System For The Embraer 190/195 Aircraft, Eduardo Francis Carvalho Freitas, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

A proposed novel DC-Link VSCF AC-DC-AC electrical power system converter for Embraer 190/195 transport category airplane is presented. The proposed converter could replace the existing conventional system based on the CSCF IDGs. Several contemporary production airplanes already have VSCF as a major or backup source of electrical power. Problems existed with the older VSCF systems in the past; however, the switched power electronics and digital controllers have matured and can be now, in our opinion, safely integrated and replace existing constant-speed hydraulic transmissions powering CSCF AC generators. IGBT power transistors for medium-level power conversion and relatively fast efficient switching are …

Design & Evaluation Of A Hybrid Switched Capacitor Circuit With Wide-Bandgap Devices For Dc Grid Applications, Joshua L. Stewart

Electrical and Computer Engineering ETDs

ABSTRACT

As technologies advance, the rate at which renewable power sources, such as solar photovoltaic (PV) and wind, are being added to the power grid is increasing. Typically, PV power plants require large inverters for direct current to alternating current (DC-AC) power conversion, as well as large transformers to step up voltages to the grid voltage. Offshore wind farms and large PV power plants in remote locations often aggregate power on a DC bus in order to improve efficiency and reduce the cost of power conversion hardware within the energy complex. However, the power must still be converted to AC …

Ionic Thermoelectric Paper, Fei Jiao, Ali Naderi, Dan Zhao, Joshua Schlueter, Maryam Shahi, Jonas Sundström, Hjalmar Granberg, Jesper Edberg, Ujwala Ail, Joseph W. Brill, Tom Lindström, Magnus Berggren, Xavier Crispin

Physics and Astronomy Faculty Publications

Ionic thermoelectric materials, for example, polyelectrolytes such as polystyrene sulfonate sodium (PSSNa), constitute a new class of materials which are attracting interest because of their large Seebeck coefficient and the possibility that they could be used in ionic thermoelectric SCs (ITESCs) and field effect transistors. However, pure polyelectrolyte membranes are not robust or flexible. In this paper, the preparation of ionic thermoelectric paper using a simple, scalable and cost-effective method is described. After a composite was fabricated with nanofibrillated cellulose (NFC), the resulting NFC–PSSNa paper is flexible and mechanically robust, which is desirable if it is to be used in …

Development Of Intermediate Band Solar Cell Through Ingan Quantum Well Structures, Kelly Mckenzie

Electrical Engineering Undergraduate Honors Theses

In the search for high-efficiency solar cells, In_xGa_1-xN has come under scrutiny as a unique material with high potential. This is due to characteristics including an easily tunable bandgap, large range of potential bandgap values, and high heat resistance. However, one factor limiting its adaptation is the high density of crystal defects. In this thesis, the qualities of InGaN are discussed and the intermediate band solar cell structure is introduced. Additionally, the growth and characterization of two sets of InGaN-based solar cell devices are reported and evaluated.

Reduction In Recombination Current Density In Boron Doped Silicon Using Atomic Hydrogen, Matthew Garett Young

Graduate Theses and Dissertations

The solar industry has grown immensely in recent years and has reached a point where solar energy has now become inexpensive enough that it is starting to emerge as a mainstream electrical generation source. However, recent economic analysis has suggested that for solar to become a truly wide spread source of electricity, the costs still need to plummet by a factor of 8x. This demands new and innovative concepts to help lower such cost. In pursuit of this goal, this dissertation examines the use of atomic hydrogen to lessen the recombination current density in the boron doped region of n-type …

Optimization Of Graphene Parameters For The Development Of Supercapacitors, Jessica L. Montgomery

Mechanical Engineering Undergraduate Honors Theses

In the growing market of evolving electronic devices and the sustainable goals of the energy industry, better sources of energy dense storage devices are needed. Carbon based supercapacitors have attracted the attention of research due to the natural properties of high electrical conductivity, chemical and electrochemical stability, and high surface area. The object of this thesis is to expand upon current knowledge of reduced graphene oxide to better understand the effectiveness of the material as electrode in supercapacitors. This thesis will focus on the physical orientation of supercapacitors to further develop a device that will allow a set of supercapacitors …

System-Layout-Dependent Thermally Induced Solder Stress & Reliability Implications, Ange C. Iradukunda

Mechanical Engineering Undergraduate Honors Theses

Electronic flip chip assemblies consist of dissimilar component materials, which exhibit different CTE. Under thermal cyclic operating conditions, this CTE mismatch produces interfacial and interconnect stresses, which are highly dependent on system layout. In this paper, sensitivity analyses are performed using ANSYS FEA to establish how the proximity and arrangement of neighboring devices affect interconnect stress. Flip chip alignment modes ranging from edge-to-edge to corner-to-corner are studied. Results of these FEA studies, demonstrated that closely packing devices together has the effect of making them act as one. This results in a significant increase in the thermomechanical stresses induced on peripheral …

Hand Cranked Generator For Mobile Devices, Kyle Brown, Monique Butoto, Stephen Cain, Steven Corio, Brock Stevenson

Thinking Matters Symposium Archive

It’s estimated that over 90% of American adults own cell phones while over 70% of the United States land area belongs to rural counties. It is a challenge to charge mobile devices in these remote and rural areas given the lack of access to power sources. This lack of power in remote destinations limits the general use of mobile devices for outdoor enthusiasts, as well as a survival means for all who need access to a portable power generation device, especially in emergency situations. There are other portable generators currently available on the market, but our project wanted to take …

Analysis And Simulation Of Photovoltaic Systems Incorporating Battery Energy Storage, Oluwaseun M. Akeyo

Theses and Dissertations--Electrical and Computer Engineering

Solar energy is an abundant renewable source, which is expected to play an increasing role in the grid's future infrastructure for distributed generation. The research described in the thesis focuses on the analysis of integrating multi-megawatt photovoltaics (PV) systems with battery energy storage into the existing grid and on the theory supporting the electrical operation of components and systems. The PV system is divided into several sections, each having its own DC-DC converter for maximum power point tracking and a two-level grid connected inverter with different control strategies. The functions of the battery are explored by connecting it to the …

Real-Time Internal Temperature Estimation And Health Monitoring For Igbt Modules, Ze Wang

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Field experiences have demonstrated that power semiconductor devices, such as insulated-gate bipolar transistors (IGBTs), are among the most fragile components of power electronic converters. Thermomechanical stresses produced by temperature variations during operational and environmental loads are the major causes of IGBT degradation. As the devices are often operated under complex working conditions, temperature variations and the associated damage are difficult to predict during the converter design stage. A promising approach—online health monitoring and prognosis for power semiconductor devices—that can avoid device failure and effectively schedule maintenance has attracted much interest.

This dissertation research focused on real-time accurate internal temperature estimation …

"Feasibility Of Efficient Photovoltaics In Eastern Kentucky" / "Developing A 3-D Printed Solar Vehicle With Computational Fluid Dynamics (Cfd) Simulator", Adam N. Stanley, Matthew R. Hezseltine

Posters-at-the-Capitol

Abstract 1

Feasibility of Efficient Photovoltaics in Eastern Kentucky

Photovoltaics (PV-also called solar photovoltaic devices) are used to harness the power of the sun via the electronic process that occurs within semiconductor cells. The solar energy is absorbed by the cells, which causes the electrons to break away from their atoms, allowing them to flow within the material to produce electricity. This electricity will become the renewable energy for Kentucky, as the generation of coal will but come to a stop within the near future. Like Denmark who is running on 100% renewable generation we must stride to become fully …

Large Scale Monolithic Solar Panel Simulation - A Study On Partial Shading Degradation, Suhas V. Baddela, Xingshu Sun, Muhammad A. Alam

The Summer Undergraduate Research Fellowship (SURF) Symposium

Shadow-induced degradation is a major concern for both power output and long-term reliability in solar cells. Apart from the obvious fact that shading reduces the amount of solar irradiance available to solar panels, it may lead to formation of hot spots, where solar cells are forced to reverse breakdown with localized heating, and potentially, permanent damage. To get a better understanding of shadow-induced degradation, we develop an electro-thermal coupled simulator that can self-consistently solve the electrical and thermal distributions of solar panel under arbitrary shading conditions. The simulation framework consists of two part: a) compact models that can describe the …

Smart Gate Driver Design For Silicon (Si) Igbts And Silicon-Carbide (Sic) Mosfets, Abdulaziz Alghanem

Electrical Engineering Undergraduate Honors Theses

The design of an efficient and smart gate driver for a Si IGBT and SiC MOSFET is addressed in thesis. First, the main IGBT parameters are evaluated thoroughly in order to understand their effects in the design of the gate driver. All known consequences of previously designed gate drivers are studied in order to achieve an optimum gate driver. As a result of this assessment, the designer is able to determine whether adding or removing components from the gate driver circuit are beneficial or not. Then, exhaustive research is done to identify suitable integrated circuits to use for the power …

Wide-Band Gap Devices For Dc Breaker Applications, Olukayode O. Sodipe

Master's Theses

With the increasing interest in wide-band gap devices, their potential benefits in power applications have been studied and explored with numerous studies conducted for both SiC and GaN devices. This thesis investigates the use of wide-band gap devices as the switching element in a semiconductor DC breaker. It involves the design of an efficient semiconductor DC breaker, its simulation in SPICE, construction of a hardware prototype and the comparative study of SiC and Si versions of the aforementioned breaker. The results obtained from the experiments conducted in the process of concluding this thesis show that the SiC version of the …

High Temperature Silicon Carbide Mixed-Signal Circuits For Integrated Control And Data Acquisition, Ashfaqur Rahman

Graduate Theses and Dissertations

Wide bandgap semiconductor materials such as gallium nitride (GaN) and silicon carbide have grown in popularity as a substrate for power devices for high temperature and high voltage applications over the last two decades. Recent research has been focused on the design of integrated circuits for protection and control in these wide bandgap materials. The ICs developed in SiC and GaN can not only complement the power devices in high voltage and high frequency applications, but can also be used for standalone high temperature control and data acquisition circuitry.

This dissertation work aims to explore the possibilities in high temperature …

Nanostructured Semiconductor Device Design In Solar Cells, Hongmei Dang

Theses and Dissertations--Electrical and Computer Engineering

We demonstrate the use of embedded CdS nanowires in improving spectral transmission loss and the low mechanical and electrical robustness of planar CdS window layer and thus enhancing the quantum efficiency and the reliability of the CdS-CdTe solar cells. CdS nanowire window layer enables light transmission gain at 300nm-550nm. A nearly ideal spectral response of quantum efficiency at a wide spectrum range provides an evidence for improving light transmission in the window layer and enhancing absorption and carrier generation in absorber. Nanowire CdS/CdTe solar cells with Cu/graphite/silver paste as back contacts, on SnO₂/ITO-soda lime glass substrates, yield the …

Indirect Matrix Converter As Standard Power Electronic Interface, Andrés Escobar-Mejía

Graduate Theses and Dissertations

The increase in the penetration levels of distributed generation in the modern power grid and its importance in future energy systems have accelerated the interest of developing new power electronic interfaces for the energy conversion process. The feasibility of applying the indirect matrix converter as the standard power electronic interface for applications with power ratings from several kW to few MW is addressed in this dissertation. Special attention is given to those applications where space dominates the power electronic requirements. The main motivation for using the indirect matrix converter is that eliminates the energy storage component in the way of …

Buck Converter, Bowen Liu

Electrical Engineering

The recent sustainable energy growth triggered a huge power electronics demand, specifically related to power conversion. My senior project is a design of a buck converter which steps down the voltage from photovoltaic cells ranging from 5 to 40V to a rechargeable battery with 5V. This converter has a high enough power efficiency to effectively convert the energy harnessed from PV panels.

Energy Harvesting From Exercise Machines: Lt8705 Dc-Dc Conversion For Elliptical Trainers, Braden Burk, Raj Bhula, Nathan Mckay

Electrical Engineering

Cal Poly’s Energy Harvesting from Exercise Machines (EHFEM) program aims to power the grid using human energy harvested from exercise machines in its gym. Doing so could save the school money and increase the total supply of power available on the grid. This document belongs to one of many groups attempting to design a suitable DC-DC conversion system for an elliptical trainer using an LT8705 Four-Switch Buck-Boost converter. Past teams have built other converters and developed system compatibility characteristics such as filtering, safety, and stability for interfacing components. These teams fall into one of two departments in EHFEM: DC-DC Conversion …