Complex Fluids Commons^™

The Influence Of Relative Particle Size And Material Interactions On The Flow-Induced Detachment Of Particles From A Microchannel, Morgan Brittany Mayfield

Graduate Theses - Chemical Engineering

Particulate transport in microfluidic channels is difficult due to confined geometries and low flow rates, which promote solids settling. To re-entrain these solids, the detachment behavior of closely-fitting particles from microchannel walls must be understood. Experiments were completed to examine the effects of particle size and material interactions on particle detachment velocity. Studies were conducted for various sizes of glass and poly(methyl methacrylate), PMMA, spheres in glass and poly(dimethyl siloxane), PDMS, microfluidic channels. In addition, an inexpensive method to produce monodisperse PMMA microparticles was developed. To analyze the effect of material interactions, the work of adhesion between the particle and …

Micro Debris Generator, Gordan Bradaric, Ross Byers, Stephen Quanci

Mechanical Engineering

This senior project team at Cal Poly consisting of Stephen Quanci, Gordan Bradaric, and Ross Byers has been commissioned by Erik Brown of Lawrence Livermore National Labs to create a way to reliably and consistently entrain microscopic particles into the hot HTTU flow. These particles will be used to compare the loading rates of new HEPA filters by measuring the pressure drop across the filter. The generated particles would simulate typical conditions in which these HEPA filters are expected to operate, namely fine ash. The particles used for loading the filter are intended to simulate the particulate reaching the LLNL …

Microstructure And Rheology Of Carbon Nanotubes At Air-Water Interfaces, Charles D. Young

Honors Scholar Theses

This work characterizes the material properties of carbon nanotubes at air-water interfaces for potential use in creating stable emulsions. Properties such as length, aspect ratio, contact angle, microstructural ordering, surface pressure, compression and shear elastic moduli, stresses, surface viscosities and non-linearity are explored. Challenges such as deviation from a classical analysis of monolayers are encountered in the form of aggregation, mechanical contributions, and interface relaxation. These factors are taken into account to explain experimental measurements and trends. Ultimately, existing models for more homogeneous systems are resolved with observations to offer insight and areas of promise moving forward.

Particle Image Velocimetry Design & Installation, Zach Ritchie

Mechanical Engineering Undergraduate Honors Theses

This work will mainly focus on the design, construction, and installation of the Particle Image Velocimetry (PIV) system in the Chemical Hazards Research Center wind tunnel. The PIV system utilizes a Class IV (double pulsed) laser, optics to produce a light sheet, timing circuitry, and a high-resolution camera (with buffered output) to measure a system’s velocity (two-dimensional) field by determining the displacement of particles over the time between laser pulses. For maximum mobility and functionality, the PIV system was installed in the center of the tunnel on a moveable cart with the laser and camera mounted to an adjustable support. …

Development Of A Parallel Multiphase Lattice-Boltzmann Solver To Study Stokes Number Effects On Particle Trajectories, Lenan Zhang, Anand Samuel Jebakumar, John Abraham

The Summer Undergraduate Research Fellowship (SURF) Symposium

Particle-laden flows are important owing to their relevance to many engineering devices such as coal combustors, gasifiers and solar thermochemical reactors. In a recent experimental study by Lau and Nathan [1], it was found that particles in a turbulent pipe flow tend to migrate preferentially depending on their Stokes number (St). Particles with a high St (>10) are concentrated near the axis while those with low St (

A Computational Study Of The Potential For Lng Tanker Polystyrene Foam Insulation Failure Under Fire Exposure, Jeffrey David Martinez

Graduate Theses and Dissertations

Liquefied natural gas is shipped across the oceans in large marine carriers. The carriers house the LNG using several different insulation systems. One of these systems involves large aluminum spheres insulated with polystyrene foam. Polystyrene foam is very susceptible to heat degradation. This raised issues as to the extent of possible insulation failure caused by a large ship fire. Experiments were done investigating the nature of polystyrene’s thermal degradation, notably by Brauman, Chen, and Matzinger and Butler. A large scale investigation was also performed by Sandia National Laboratory. However, computational modeling of the degradation was lacking. This work set out …

Novel Separation Methods Using Electrodialysis/Electrodeionization For Product Recovery And Power Generation, Alexander Miguel Lopez-Rosa

Graduate Theses and Dissertations

The use of electrodialytic separations for the purification of products has been a vital technique for the past 50 years in the chemical industry. Originally used for demineralization and desalination, electrodialysis and its counterparts have expanded to assist in product purification, waste and hazard removal, and power generation. This research focused on the development of high purity organic acids purification with low power requirements. Work resulted in the development of a new type of electrodialysis process, specifically the use of ionic liquids as a secondary solvent for the development of dual solvent electrodialysis. Through dual solvent electrodialysis, ions were recovered …

Coalescence-Induced Jumping Of Droplet: Inertia And Viscosity Effects, Samaneh Farokhirad, Jeffrey F. Morris, Taehun Lee

Publications and Research

The problem of coalescence-induced self-propelled jumping of droplet is studied using three-dimensional numerical simulation. The focus is on the effect of inertia and in particular the effect of air density on the behavior of the merged droplet during jumping. A lattice Boltzmann method is used for two identical, static micro-droplets coalescing on a homogeneous substrate with contact angle ranging from 0◦ to 180◦. The results reveal that the effect of air density is significant on detachment of the merged droplet from the substrate at the later stage of the jumping process; the larger the air density, the larger the jumping …

A Study On The Heavy Crude Oil Viscosity Reduction With The Dissolution Of Nitrogen And Carbon Dioxide, Abdurahman Ajumobi

Dissertations and Theses

World's energy challenges would be greatly improved upon if half of the world's heavy oil and extra heavy oil could be made to ow in pipelines. Viscosity reduction of heavy oils is the key to solving this problem. In this study, aside from injecting pure nitrogen and pure carbon dioxide separately into the oil, two different compositions of the mixture of the two gases were also injected. In the first mixture, varied quantities of the two gases were used; 62:5%, 82:2% and 86:4% of the mixture was nitrogen while 37:5%, 17:8% and 13:6% was carbon dioxide at total test pressures …

Fundamental Studies Of Surfactant Templated Metal Oxide Materials Synthesis And Transformation For Adsorption And Energy Applications, Saikat Das

Theses and Dissertations--Chemical and Materials Engineering

This work addresses fundamental aspects of designing templates and curing conditions for the synthesis of mesoporous metal oxide thin films. The first section addresses selection of cationic-carbohydrate surfactant mixtures to synthesize templated silica thin films for selective adsorption of simple carbohydrates based on molecular imprinting. Nuclear magnetic resonance and fluorescence spectroscopy results suggest a novel structure for mixtures of alkyl glucopyranosides or xylopyranosides with cationic (trimethylammonium) surfactants. Despite thermodynamically favorable mixing, the carbohydrate headgroups in the mixed micelle adopt an inverted configuration with their headgroups in the micelle core, and therefore are inaccessible for molecular imprinting. This orientation occurs even …

Measurements And Modeling Of Hydrocarbon Mixture Fluid Properties Under Extreme Temperature And Pressure Conditions, Babatunde A. Bamgbade

Theses and Dissertations

Knowledge of thermodynamic fluid properties, such as density and phase behavior, is important for the design, operation, and safety of several processes including drilling, extraction, transportation, and separation that are required in the petroleum. The knowledge is even more critical at extreme temperature and pressure conditions as the search for more crude oil reserves lead to harsher conditions. Currently, there is dearth of experimental data at these conditions and as such, the predictive capability of the existing modeling tools are unproven. The objective of this research is to develop a fundamental understanding of the impact of molecular architecture on fluid …

Stability Of Aqueous Dispersions Of Titanium Dioxide Against Sedimentation And Aggregation, Guanrong Bai, Xilan Zhu, Elias I. Franses, David S. Corti, Yung-Jih Yang

The Summer Undergraduate Research Fellowship (SURF) Symposium

Particles of titanium dioxide (TiO₂) are widely used as white pigments in paints and inks, due to their brightness and high refractive index. Yet, with TiO₂ having a high density (4.2 g/cm³), particles with typical sizes of 300 nm sediment rapidly even before significant agglomeration can occur. Thus, increasing the stability of TiO2 dispersions against sedimentation as well as aggregation is important. We studied the effect of sodium dodecyl sulfate (SDS), a commonly used dispersant, on the stability of aqueous dispersions of TiO₂ with weight fractions from 0.01 to 40. The sedimentation time of …

Effect Of Sodium Dodecyl Sulfate And Sodium Chloride On The Stability Of Aqueous Dispersions Of Tio2 Particles Against Aggregation And Sedimentation, Xilan Zhu, Guanrong Bai, Elias I. Franses, David S. Corti, Yung-Jih Yang

The Summer Undergraduate Research Fellowship (SURF) Symposium

Dispersions of TiO₂ particles are widely used as the main pigment in white inks for inkjet printers due to its brightness and high opacity. The TiO₂ particles, however, have a high density, and so the possible fast settling of these particles can cause maintenance problems for the printers and lower the printing quality. We studied the effect of sodium dodecyl sulfate (SDS), a commonly used dispersant, on the stability of 1 wt% TiO2 aqueous dispersions, both with and without NaCl, against aggregation and sedimentation. The sedimentation half time (t50), defined as the time need for the particles to …

A Soft Condensed Matter Approach Towards Mathematical Modelling Of Mass Transport And Swelling In Food Grains, Michael Chapwanya, N. Misra

Articles

Soft condensed matter (SCM) physics has recently gained importance for a large class of engineering materials. The treatment of food materials from a soft matter perspective, however, is only at the surface and is gaining importance for understanding the complex phenomena and structure of foods. In this work, we present a theoretical treatment of navy beans from a SCM perspective to describe the hydration kinetics. We solve the transport equations within a porous matrix and employ the Flory–Huggin’s equation for polymer–solvent mixture to balance the osmotic pressure. The swelling of the legume seed is modelled as a moving boundary with …

Effect Of Ionic Liquid Electrolytes In Dsscs With Titanium Dioxide (Tio2) Inverse Opal Structures, Naomi S. Ramesar

Dissertations and Theses

Dye-sensitized solar cells (DSSC) are low-cost alternatives to conventional solar cells that can work well in low-light conditions. Despite considerable study on improving the efficiency of DSSCs, the current liquid electrolyte cell has plateaued at a conversion efficiency of ~ 12%. A major problem with these cells regarding their applicability is the low viscosity and high volatility of the toxic electrolyte, i.e., acetonitrile, which cause leakage and volatilization. We propose that using ionic liquids (ILs), which are more viscous, less volatile, and conductive, may be more suitable electrolytes. However, one unwanted side effect of the higher viscosity of the ILs …

Low Volume Dispensing With High Speed Dispensers, Sunny Agarwal

Graduate Dissertations and Theses

With the high pace of innovation in the semiconductor manufacturing industry, there has been an increasing demand for more energy efficient and environmental friendly products. This research relates to a complex process of fluid dispensing at low volumes on a printed circuit board. Currently, a more refined non-contact dispensing terminology named “Streaming” is widely used to stream out material at low volumes for various applications. The key solution is to frame a dispensing method that lends itself most closely to the requirements of a specific production process.

This study represents a detailed approach of dispensing low volumes of materials in …

Method And Apparatus For Measurement Of Fluid Properties, Feredoon Behroozi

Patents (University of Northern Iowa)

A method and apparatus for determining the contact angle and/or surface tension of a liquid on a solid surface is described. The method involves placing a fluid drop on a solid surface, and gradually increasing its volume by adding more fluid, while continuing to determine the corresponding increase in fluid height, until the drop attains maximum height beyond which additional fluid only increases the drop footprint and not height, and determining the equilibrium height and in turn the contact angle by means of an equation that correlates contact angle with depth below the fluid surface, together with the fluid surface …

Efficient Numerical Scheme Of The Dynamics Of Nonisothermal Thin Film Flow, Moustafa A. Soliman, Khalid I. Alhumaizi

Chemical Engineering

In this work we use Lubrication type method, based on the possibility of the separation of longitudinal and transversal length scales to simplify the analysis of thin film dynamics. We study the dynamics of evaporating thin liquid films on an inclined plane, where the effect of van der Waal forces is significant. The numerical solution of the evolution equation is carried out using the method of orthogonal collocation and is used for the study of the instabilities of evaporating thin film to identify conditions for efficient operation. For symmetric cases where the plane is horizontal, a two spline collocation second …

Dynamics Of A Coating Film Flow On Horizontal Cylinders With Van Der Waals Forces, Moustafa A. Soliman, Khalid I. Alhumaizi

Chemical Engineering

In this work we use the lubrication type method, based on the possibility of the separation of longitudinal and transversal length scales, to simplify the analysis of coating film dynamics. We study the dynamics of coating thin films on horizontal stationary and rotating cylinders in general, and when the effect of van der Waals forces is significant. A computer code based on the method of orthogonal collocation is developed and is used for the study of the instabilities of coating thin film flow on cylinders to identify conditions of stable operation. For stationary cylinders, the equations are symmetric and the …

Characterization And Quantification Of Monomers, Oligomers, And By-Products From Xylan During Biomass Pretreatment, Ching-Shuan Lau

Graduate Theses and Dissertations

Biomass pretreatment generates inhibitory products, which reduce the overall yield of xylose for ethanol production. Understanding of hemicellulose depolymerization into xylose is essential to identify the pretreatment conditions that maximize xylose formation, but minimize the generation of these inhibitory products, such as formic acid and furfural. Thus, the goal of this project is to understand how dilute acid pretreatment parameters affect hemicellulose depolymerization, maximize xylose concentrations, and minimize by-products formation.

To progress towards this goal, rates and mechanisms of hemicellulose release must be determined. Birchwood xylan was used as the starting material to produce xylose oligomers. The hydrolyzed birchwood xylan …

Plasmonic Pervaporation Via Gold Nanoparticle-Functionalized Nanocomposite Membranes, Aaron Russell

Graduate Theses and Dissertations

Butanol derived from biological feedstocks has significant potential as a liquid fuel source, but the separation methods used in its production can be prohibitively expensive and are therefore currently the subject of extensive research. Pervaporation is a promising membrane process that is effective in butanol separations, but involves a large energy demand. This study examines the possibility of increasing flux and energy efficiency in pervaporation via plasmonic heating of gold nanoparticle-functionalized, polymer nanocomposite membranes (AuNCMs) in lieu of conventional feed heating. An economic analysis demonstrated that plasmonic pervaporation could achieve significant reductions in energy usage and utility cost in butanol …

Cloning And Characterization Of Sas0754, A Hypothetical Protein From Community Associated Staphylococcus Aureus, Unknown Unknown

Symposium 2012

Community associated Staphylococcus aureus (strain MSSA476) is a gram positive cocci capable of infecting many different parts of the body and known to cause serious infections that can be fatal, such as bacterial arthritis and acute endocarditis. To find effective ways of fighting against CA-MRSA strains we must learn more about their ability to infect. The focus of this study was cloning and characterization of a protein referred to as SAS0754. The size of SAS0754 is 340 amino acids and the gene sequence is 1023 nucleotides. The hypothetical function of this protein is that it is an extracellular matrix binding …

A Convenient Synthesis Of 2,6-Dichlorohomonicotinic Acid, Chase Buchanan, Richard W. Fitch

Symposium 2012

In our synthetic efforts toward the alkaloid phantasmidine, we required a convenient source of the title compound. Herein, we describe a short synthesis of 2,6-dichlorohomonicotinic acid by direct allylation of 2,6-dichloropyridine with LDA/allyl chloride, followed by permanganate oxidation of the side chain [figure1]. Yields for the allylation are high, while permanganate oxidation required more adjustment. Successful conditions require the modest acidification of the mixture with acetic acid and cleanup by acid base workup. No chromatography is needed.

Convenient Parallel Synthesis Of Alkyl- And Aryl-S-Tert-Butyl Thiothers, Rebecca Norcross, Jessica Stanfield, Richard W. Fitch

Symposium 2012

While preparing novel cysteine derivatives as oxidation catalysts, we needed S-tert-butylcysteine. We also examined acid-promoted tert-butylation of thiols using tert-butanol as reagent and solvent. While cysteine and aminoethanethiol work well using tBuOH in 4M HCl, other thiols fail in the aqueous environment and aerobic conditions. We examined a variety of aliphatic and aromatic thiols in tBuOH with H2SO4 catalysis and found that argon sparging and the use of 1 eq of acid led to good yields in a parallel format.

Degradation Of Polystyrene Foam Under Radiant Heat Flux, James Butler

Graduate Theses and Dissertations

As the demand for liquefied natural gas has increased, safety concerns about the performance of transport vessels under fire conditions have been raised. Current codes for the sizing of the pressure relief systems require that the vessels are able to withstand an emmissive heat flux of 108kW/m2 and do not take into account the effects of insulation loss due to thermal decomposition of the insulation materials. To address this possible oversight in the current code models were presented to a working group organized by the Society of International Gas Tanker and Terminal Operators Ltd. focusing on the decomposition rate of …

Rayleigh Test Apparatus Design Report, Josef Duller, Owen Raybould, James Nicovich

Mechanical Engineering

The Rayleigh Test Apparatus is a device that will be used to test the thermodynamic properties of Nitrous Oxide to assess the feasibility of using this fluid as a coolant for a hybrid rocket aero spike. The aero spike is intended to redirect the propulsion flow as it leaves the engine to create a more efficient flow pattern at low and high altitudes. However, there are issues of overheating which leads to melting of the aero spike. For this reason, the use of nitrous oxide (N2O) as a coolant is being explored. N20 is being considered because it is already …

L'Oreal Waste Minimization, Caitlin Burns, Joe Baugh, Allen Busick, Ryan Black, Emily Evans, Matthew Margis

Chemical Engineering Undergraduate Honors Theses

The purpose of this design project is to reduce the amount of waste being generated at L’Oreal’s North Little Rock manufacturing facility. To accomplish this, the design team visited the North Little Rock manufacturing facility to examine the areas producing the most waste. After gaining a detailed understanding of these areas, the UP1 production line was identified as one of the largest opportunities for waste reduction in the L’Oreal manufacturing facility. In the UP1 processing area, mascara is mixed in large mixing tanks and then pumped in to barrels to be packaged. The 2,000 liter and 1,000 liter Olsa tanks …

Simulation, Synthesis, And Characterization Of Hydrogels And Nanocomposite Gels., Kamleshkumar J. Suthar

Dissertations

Stimuli-responsive gels are three-dimensional, cross-linked polymeric materials that undergo large physical change in response to the environmental stimuli, like temperature, pH, electrical potential, and irradiation. Ferrogels are colloidaldispersion of magnetic nanoparticles in the hydrogel network. The magnetic nanoparticles are attached to the polymeric network by different adhesive forces; as a result, it becomes sensitive to the applied magnetic field.

The main objective of this research is the simulation, synthesis, and characterization of the hydrogel and ferrogel. Simulation of the hydrogel response was performed for various environmental stimuli using a multiphysics finite element analysis software, COMSOL. The pH and electrical response …

Kinetics Determination Of Soybean Oil Transesterification In The Design Of A Continuous Biodiesel Production Process, Irwin Jacob, Ed Clausen, Danielle Julie Carrier

Biological and Agricultural Engineering Undergraduate Honors Theses

One-step batch transesterification consisting of three stepwise reversible reactions of pure soybean oil with methanol was conducted at two different mixing speeds (600 and 300 rpm) to produce soybean oil fatty acid methyl esters (biodiesel). In both batch reactions, sodium methoxide (1.09 wt% based on soybean oil) was used as the catalyst, the reaction temperature was 60oC, and the methanol-to-oil molar ratio was 6:1. The objectives were to determine and/or investigate: 1) the mechanism and order of the reaction, 2) the reaction rate constants, 3) the effect of changes in mixing intensity on the reaction rate, 4) the comparison of …

Emulsification And Dispersant Properties Of Sugar Ester Glycolipid In Water In Oil And Oil In Water Emulsion., Azrah Abdul Aziz

Student Works (2010-2019)

The influence of different dispersing agent on the rheological behaviors of paraffin oil-water emulsion with addition of TiO2 for uv-protect and moisturizing active ingredient was studied. While making creams with minimal structural defects and longer storage stability, it is important that preparation conditions be optimized. Settle volume properties, Zeta potential, effective diameter and settle volume of TiO2 suspension were studied in the presence of glycolipid (DDM and Carrageenan), nonionic (PEG 10,000 and Brij 35P) as well as anionic surfactants (sodium dodecyl sulfate, SDS). In the experiments, the higher concentration of dispersing agents shows higher settle volume percentage, higher zeta potential …