Engineering Commons^™

A Protocol For Automated A Posteriori Adaptive Meshing With Simvascular: A Test Case, Akash Gupta, Ethan Kung

Publications

Objective

Operational details regarding the use of the adaptive meshing (AM) algorithm available in the SimVascular package are scarce despite its application in several studies. Lacking these details, novice users of the AM algorithm may experience undesirable outcomes post-adaptation such as increases in mesh error metrics, unpredictable increases in mesh size, and losses in geometric fidelity. Here we present a test case using our proposed iterative protocol that will help prevent these undesirable outcomes and enhance the utility of the AM algorithm. We present three trials (conservative, moderate, and aggressive settings) applied to a scenario modelling a Fontan junction with …

Capturing Spatial Variability In Maize And Soybean Using Stationary Sensor Nodes, Jasreman Singh, Derek M. Heeren, Yufeng Ge, Geng Bai

Department of Agricultural and Biological Systems Engineering: Faculty Publications

• Irrigation in agriculture maximizes crop yield and improves food security globally • Irrigation scheduling is strongly based on the ability to accurately estimate the appropriate amount and timing of water application • The timing of the irrigation can best be informed through the crop canopy stress, and the amount of irrigation is informed through soil moisture depletion

• Developing upper (non-water stressed) and lower (non-transpiring) baselines for irrigated and non-irrigated maize and soybean • Investigating the relationship between the canopy stress and the soil moisture stress

The canopy temperature stress and soil moisture depletion had stronger correlation for non-irrigated …

Questaal: A Package Of Electronic Structure Methods Based On The Linear Muffin-Tin Orbital Technique, Dimitar Pashov, Swagata Acharya, Walter R.L. Lambrecht, Jerome Jackson, Kirill Belashchenko, Athanasios Chantis, Francois Jamet, Mark Van Schilfgaarde

Kirill Belashchenko Publications

This paper summarises the theory and functionality behind Questaal, an open-source suite of codes for calculating the electronic structure and related properties of materials from first principles. The formalism of the linearised muffin-tin orbital (LMTO) method is revisited in detail and developed further by the introduction of short-ranged tight-binding basis functions for full-potential calculations. The LMTO method is presented in both Green's function and wave function formulations for bulk and layered systems. The suite's full-potential LMTO code uses a sophisticated basis and augmentation method that allows an efficient and precise solution to the band problem at different levels of theory, …

Investigation Of Manual Material Handling On Musculoskeletal Disorder At Computer Numerical Control Workstation, Abdullah Nor Suliani

Student Works (2020-2029)

Manual Material Handling (MMH) tasks have been recognized among the major source of work-related musculoskeletal disorder (WMSD) in automotive industry and they are commonly practiced at Computer Numerical Control (CNC) workstation. At this workstation, workers act as a material transfer device in the process of loading and unloading products from pallets to machines. The physical interaction of workers to machine is not self-chosen and workers are forced to follow the pace of running CNC machine. The worst situation happens when workers are required to operate more than one machine concurrently. The mismatch interaction between workers and machine exposes workers to …

Development Of B-Type And Multi-Ion Doped Carbonated Hydroxyapatite Bioceramics, Safarzadeh Marjan

Student Works (2020-2029)

The present research is aimed to investigate the effect of varying the carbonate to phosphate (CO32−/ PO43‒) molar ratios from 0.5 to 5 on the physical and mechanical properties of carbonated hydroxyapatite (CHA) synthesized by a wet chemical method. The sintering was performed under dry carbon dioxide atmosphere at 900 °C to maintain the B-type CHA structure. It was found that increases in CO32−/ PO43‒ ratio was accompanied by an increase in the c/a lattice ratio. The diffraction peaks of the synthesized 0.5-5 CHA powders exhibited a single phase material except for 5CHA which revealed the some minor calcite or …

Dynamic And Control Of Air-Bearing Spacecraft Simulator, Jacob Joseph Korczyk

Doctoral Dissertations and Master's Theses

An air bearing is being designed as a spacecraft rotational motion simulator, featuring the Sawyer Robot and its control box. The objective is to maneuver the robot as desired, performing operations specific to on-orbit servicing operations while maintaining stability of the system. Before the control can be designed, the dynamics of the platform and the robot must be modeled. The dynamics of the robot can be derived utilizing a Newton-Euler recursive approach. By beginning with a simple pendulum, then adding links (degrees of freedom) to more closely resemble the Sawyer arm, the equations of motion for the robot can be …

Differentially Private Online Task Assignment In Spatial Crowdsourcing: A Tree-Based Approach, Qian Tao, Yongxin Tong, Zimu Zhou, Yexuan Shi, Lei Chen, Ke Xu

Research Collection School Of Computing and Information Systems

With spatial crowdsourcing applications such as Uber and Waze deeply penetrated into everyday life, there is a growing concern to protect user privacy in spatial crowdsourcing. Particularly, locations of workers and tasks should be properly processed via certain privacy mechanism before reporting to the untrusted spatial crowdsourcing server for task assignment. Privacy mechanisms typically permute the location information, which tends to make task assignment ineffective. Prior studies only provide guarantees on privacy protection without assuring the effectiveness of task assignment. In this paper, we investigate privacy protection for online task assignment with the objective of minimizing the total distance, an …

Attribute-Based Cloud Data Integrity Auditing For Secure Outsourced Storage, Yong Yu, Yannan Li, Bo Yang, Willy Susilo, Guomin Yang, Jian Bai

Research Collection School Of Computing and Information Systems

Outsourced storage such as cloud storage can significantly reduce the burden of data management of data owners. Despite of a long list of merits of cloud storage, it triggers many security risks at the same time. Data integrity, one of the most burning challenges in secure cloud storage, is a fundamental and pivotal element in outsourcing services. Outsourced data auditing protocols enable a verifier to efficiently check the integrity of the outsourced files without downloading the entire file from the cloud, which can dramatically reduce the communication overhead between the cloud server and the verifier. Existing protocols are mostly based …

Two Can Play That Game: An Adversarial Evaluation Of A Cyber-Alert Inspection System, Ankit Shah, Arunesh Sinha, Rajesh Ganesan, Sushil Jajodia, Hasan Cam

Research Collection School Of Computing and Information Systems

Cyber-security is an important societal concern. Cyber-attacks have increased in numbers as well as in the extent of damage caused in every attack. Large organizations operate a Cyber Security Operation Center (CSOC), which forms the first line of cyber-defense. The inspection of cyber-alerts is a critical part of CSOC operations (defender or blue team). Recent work proposed a reinforcement learning (RL) based approach for the defender’s decision-making to prevent the cyber-alert queue length from growing large and overwhelming the defender. In this article, we perform a red team (adversarial) evaluation of this approach. With the recent attacks on learning-based decision-making …

Verification Of Effectiveness Of Spot-Heating Technique In Reducing Spread Of Weld Lines In Injection Molded Plastic Products, Shah Ashikul Abed Sakar

Masters Theses

In producing a plastic part in an injection molding machine many physical factors related to the machine, such as injection pressure, holding pressure, heater temperature, etc. play their roles in the overall quality of the produced part. There are many aspects of the quality of a plastic part, such as part strength, part dimensions, and part surface finish. If any of those aspects gets compromised, the part is considered to have some defects. Of all defects found in injection-molded plastic parts, one most common defect is the presence of weld lines.Weld lines are formed when the flow of the molten …

Numerical Investigation Of Leading-Edge Modifications Of A Naca Airfoil, Anisur Rahman Ikram

Masters Theses

A parametric investigation was carried out to understand the flow characteristics of tubercle airfoils and to determine the best approach and parameters for designing a tubercle airfoil. For this purpose, a straight edge base airfoil (NACA 4414) and several tubercle airfoils, by modifying the leading edge of the base airfoil, were created in SolidWorks and tested with Computational Fluid Dynamics (CFD) application software Star CCM+.

Alternative tubercle airfoil with elliptical bumps demonstrated superior post-stall performance when compared to their straight edge counterparts; their post-stall lift did not decrease drastically. However, their pre-stall lift coefficients were always lower than the base …

Effects Of Collision Damage On The Ultimate Strength Of Fpso Vessels, Muhammad Zubair Muis Alie, Dian Ramasari, Taufiqur Rachman, Ristiyanto Adiputra

Makara Journal of Technology

Floating production storage offloading (FPSO) vessels are movable offshore structures. These structures are designed with large dimensions, and their decks are loaded with several types of equipment. During collision damage, the hull and deck parts loaded with equipment are severely affected. Therefore, the ultimate strength of FPSO vessels should be thoroughly checked and evaluated. The objective of the present study is to analyze the ultimate strength of FPSO vessels against collision damage characterized by hogging and sagging under longitudinal bending. The cross section of an FPSO vessel is modeled with elements composed of stiffened and unstiffened plates. The vessel length …

Ionic Conductivity And Electrochemical Properties Of Alginate–Nn4no3-Based Biopolymer Electrolytes For Edlc Application, Norfatihah Binti Mazuki, Nur Muhitul Jalilah Rasali, Bouchta Sahraoui, Ahmad Salihin Samsudin

Makara Journal of Technology

In this work, alginate doped with various contents of ammonium nitrate (NH4NO3) as a solid biopolymer electrolyte (SBE) was prepared via casting by using distilled water as a solvent. Impedance studies on alginate–NH4NO3 SBE films were conducted via impedance spectroscopy. The lowest bulk resistance (Rb) showed that the maximum ionic conductivity of the sample containing 25 wt.% NH4NO3 at ambient temperature (303 K) was 5.56 × 10−5 S cm−1. The temperature dependence of ionic conductivity was evaluated, and results confirmed that electrolytes followed an Arrhenius behavior. The highest conducting sample was fabricated into an electrical double-layer capacitor and characterized in …

Synthesis Of Epoxy Monoethanolamide From Bauhinia Monandra Seed Oil, Adewale Adewuyi, Rotimi A. Oderinde

Makara Journal of Technology

In this study, we synthesized epoxidised monoethanolamide (EMA) from Bauhinia monandra seed oil (BMO) via a simple reaction route. In this process, BMO was transesterified to obtain a mixture of methyl esters, which was subjected to a urea adduct complexation reaction. The unsaturated methyl esters (BME) from the urea adduct complexation reaction were then epoxidised using performic acid produced in situ in a one-pot reaction system. The epoxidised methyl esters were converted to EMA by reacting them with monoethanolamine (1:10). The progression of the reaction was monitored using Fourier transform infrared spectroscopy and proton nuclear magnetic resonance spectroscopy, and the …

Multi-Level-Phase Deep Learning Using Divide-And-Conquer For Scaffolding Safety, Sayan Sakhakarmi, Jee Woong Park

Civil and Environmental Engineering and Construction Faculty Research

A traditional structural analysis of scaffolding structures requires loading conditions that are only possible during design, but not in operation. Thus, this study proposes a method that can be used during operation to make an automated safety prediction for scaffolds. It implements a divide-and-conquer technique with deep learning. As a test scaffolding, a four-bay, three-story scaffold model was used. Analysis of the model led to 1411 unique safety cases for the model. To apply deep learning, a test simulation generated 1,540,000 datasets for pre-training, and an additional 141,100 datasets for testing purposes. The cases were then sub-divided into 18 categories …

Ethylene Carbonate And Polyethylene Glycol As Efficient Plasticizers In Cmc-Pva-Nh4no3-Based Polymer Electrolyte, Noor Saadiah Mohd Ali, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

This study investigated the influence of plasticizers (polyethylene glycol [PEG] and ethylene carbonate [EC]) on the ionic conduction of CMC-PVA-NH4NO3. Blended biopolymer electrolytes (BBEs) based on carboxymethyl cellulose–polyvinyl alcohol (CMC-PVA) doped with ammonium nitrate (NH4NO3) were obtained via casting solution technique incorporated with PEG and EC, which acted as plasticizers. Electrical impedance spectroscopy (EIS) was conducted to evaluate the effect of plasticization on the ionic conduction properties. The ionic conductivity improved from 1.70 × 10−3 S/cm for un-plasticized BBEs to 3.92 × 10−3 S/cm for plasticized BBEs with EC and 3.00 × 10−3 S/cm for plasticized BBEs with PEG. The …

Current Status Of Hydrothermal Treatment For Energy And Material Recovery Toward A Sustainable Post-Consumer Material Cycle, Baskoro Lokahita, Muhammad Aziz, Fumitake Takahashi

Makara Journal of Technology

The demand for energy-efficient and environmentally friendly municipal solid waste (MSW) processing has increased in developing countries. The thermochemical process offers a fast and reliable solution to reutilize or reduce the volume of MSW. Hydrothermal treatment is a novel MSW treatment technology that is compatible with high-moisture-content feedstock. It involves the thermal degradation of MSW in pressurized water or steam, which promotes the disintegration of cellulosic and polymer materials. Recent advances have shown effective MSW conversion into homogenous solid hydrochar with higher energy density. Alkali and chlorine content, which causes issues in combustors, was successfully removed due to the washing …

Liquefaction Potential Analysis Based On Nonlinear Ground Response On The Coastline Of Bengkulu City, Indonesia, Lindung Zalbuin Mase

Makara Journal of Technology

This paper presents the study of the seismic response and liquefaction potential of the coastal area of Bengkulu City during the September 2007 Sumatra earthquake. The study is conducted by collecting site investigation data (standard penetration test) and applying input motion to observe soil response. Synthetic ground motion is generated by considering the important aspects of earthquakes, including focal depth, epicenter, earthquake source, and site classification. The synthetized ground motion is then used as the input motion in the seismic response analysis. The results of this analysis are spectral acceleration and peak ground acceleration at each depth. The resulting spectral …

Comparison Of Phytoremediation And Filtration For Diamond-Mine-Tailings Water Treatment, M. Hafidhuddin Noor, Mijani Rahman, Akhmad Gazali, Nia Kania, Aulia Rahma, Erdina L.A. Rampun, Amalia E. Pratiwi, Muthia Elma

Makara Journal of Technology

The water pollution caused by diamond mine activities can kill aquatic life. In this work, we used phytoremediation and filtration to treat pond water polluted by the tailings of a diamond mine located in South Kalimantan, Indonesia. Einchhornia crassipes (water hyacinth) was utilized as the biomass for the phytoremediation process. Gravel (10–15 mm) and sand (0.1–1 mm) were used as filter media in the simple filtration setup, using an up-flow system (bottom to top). In the experiment, 16 L of diamond tailing water was poured into five phytoremediation reactors (each 60 L in volume), which were then tested over seven …

Drones Detection Using Smart Sensors, Aishah Moafa

Doctoral Dissertations and Master's Theses

Drones are modern and sophisticated technology that have been used in numerous fields. Nowadays, many countries use them in exploration, reconnaissance operations, and espionage in military operations. Drones also have many uses that are not limited to only daily life. For example, drones are used for home delivery, safety monitoring, and others. However, the use of drones is a double-edged sword. Drones can be used for positive purposes to improve the quality of human lives, but they can also be used for criminal purposes and other detrimental purposes. In fact, many countries have been attacked by terrorists using smart drones. …

Implementing A Transporter Performance Management System In A Hospital Imaging Department, Sarah Dunn

Honors Capstones

No abstract provided.

Scanning Electron Microscopy (Sem) Investigation Of Morphology Changes In The Reduction Of Silica Nanoparticles To Elemental Silicon, Allison M. Cairns

University Honors Theses

The application of silicon nanoparticles varies from energy storage materials, to drug-delivery, and molecular recognition. Various chemical and physical properties of the Si nanoparticles arise from their morphology. This paper aims to reveal the morphology of Si nanoparticles following magnesiothermic reduction of silica (SiO₂) nanoparticles. Two sets of SiO₂ nanoparticles were used, commercially available NanoXact nanoparticles and laboratory-synthesized Stöber nanoparticles. A Zeiss Sigma VP FEG SEM was used to examine the morphology. Following the magnesiothermic reduction, the nanoparticles were etched with HF. Ten sets of images were taken of both Stöber and NanoXact nanoparticles: 1,2: the SiO …

Extending Water Resources Performance Metrics To River Ecosystems, Belize A. Lane, J. Pablo Ortiz-Partida, Samuel Sandoval-Solis

Civil and Environmental Engineering Faculty Publications

A persistent challenge in integrated water management is the ability to accurately evaluate human and ecological tradeoffs. Two-dimensional (2D) hydraulic models are frequently used to evaluate water management alternatives concerning aquatic species physical habitat needs or preferences. Recent studies have assessed the timing or duration of suitable habitat conditions, but no standardized approach exists to integrate and interpret ecohydraulic model outputs within a water management framework. Such an approach is needed to maximize the information obtained from model outputs and to facilitate communication between river scientists and water managers. This study presents a general framework to aggregate and summarize 2D …

Production Of Renewable Hydrocarbon Fuel Via Titanium Oxide-Alumina (Tio2-Al2o3) Catalytic Deoxygenation Reaction, Xian Yih Ooi

Student Works (2020-2029)

The renewable hydrocarbon-like biofuel from biomass is crucial to substitute fossil fuel. Catalytic deoxygenation is a biofuel upgrading process to eliminate the high oxygen content in biofuel which will lead to corrosion, instability and lower heating value problems. The choice of support is significant to provide the maximum acid strength for the hydrogenolysis of C-O bonds. Al2O3 supported catalyst has drawn attention due to the high acidity. However, the high acidity leads to coke deposition, unstable and deactivation of the catalyst. Thus, it is important to develop methods to improve catalyst performance, reduce catalyst coking and enhance catalyst lifetime. Recently, …

Fatigue Damage Assessment Of Reinforced Concrete Slabs Using Integrated Dynamic Testing And Simulation, Jamadin Adiza

Student Works (2020-2029)

Assessment of existing fatigued structures is an important aspect of civil engineering infrastructure. This is critical in most loaded civil engineering structures such as bridges that are constantly subjected to dynamic loading, causing fatigue in the materials over time. Bridge deck slabs are one of the most structural elements susceptible to different cyclic loads, requiring regular checks for damage to fatigue. In order to understand the deterioration, fatigue carrying capacity and residual strength, the serviceability of the slab under the fatigue loads was not fully explored. Therefore, this research is designed to use vibration-based techniques to investigate the integrity of …

Poly(Vinyl Alcohol)/Α-Chitin/Nanocellulose Composites Developed From Oil Palm Empty Fruit Bunch (Opefb) For Removal Of Cationic Dyes, Chun Fah Mok

Student Works (2020-2029)

In search of an eco-friendly polymeric adsorbent for dye effluent treatment application, poly(vinyl alcohol) (PVA)/chitin/nanocellulose composites were synthesized. The composites were reinforced by oil palm empty fruit bunch fibers (OPEFB)-derived nanocrystalline cellulose (NCC). With addition of 1 wt.% NCC, a maximum improvement of 57.64% and 50.66% in tensile strength and Young’s Modulus were achieved, respectively. However, the PVA-based composites exhibited low resistance in aqueous medium. Hence, maleic acid (MA) was incorporated, in view of modifying PVA-based composites through cross-linking reactions. The effect of varying chitin content (10 wt.%-30 wt.%) and MA content (10%-50% based on total solid content of composite) …

Detailed Modeling Of A Small-Scale Turbulent Pool Fire, Bifen Wu, Somesh Roy, Xinyu Zhao

Mechanical Engineering Faculty Research and Publications

Turbulent pool fires have been studied as a canonical configuration in fire science with wide interest. A numerical study of a small-scale turbulent heptane pool fire is conducted in the present study to understand the interactions and coupling among turbulence, chemistry, soot, and radiation in pool fires. A Monte Carlo ray tracing based radiation solver, with line-by-line spectral models for five gaseous species and soot, is coupled with a fireFOAM-based reacting flow solver to describe the dynamics of the target fire. A 33-species skeletal mechanism is employed to describe the finite-rate chemistry. A two-equation soot model with C₂H …

Supporting Self-Regulation Of Children With Adhd Using Wearables: Tensions And Design Challenges, Franceli L. Cibrian, Kimberley D. Lakes, Arya Tavakoulnia, Kayla Guzman, Sabrina Schuck, Gillian R. Hayes

Engineering Faculty Articles and Research

The design of wearable applications supporting children with Attention Deficit Hyperactivity Disorders (ADHD) requires a deep understanding not only of what is possible from a clinical standpoint but also how the children might understand and orient towards wearable technologies, such as a smartwatch. Through a series of participatory design workshops with children with ADHD and their caregivers, we identified tensions and challenges in designing wearable applications supporting the self-regulation of children with ADHD. In this paper, we describe the specific challenges of smartwatches for this population, the balance between self-regulation and co-regulation, and tensions when receiving notifications on a smartwatch …

Hybrid Non-Destructive Assessment For Flow Induced Vibration Piping Systems Using Coupled Fluid-Structure Interaction, Keen Kuan Kong

Student Works (2020-2029)

Pipelines and piping systems are of great importance in many industries such as water supply, petroleum and petrochemicals and nuclear power generation. They provide transport for high-velocity pressurized fluids operating under time-varying conditions. They are required to operate non-stop for a schedule of 24 hours a day, 7 days a week. Piping vibration failures have been one of the major causes of downtime, fires and explosions in industrial plant over the past 30 years. Failure of piping systems can have disastrous effects, leading to injuries and fatalities as well as to substantial cost to industry and the environment. Flow-induced vibration …

Parametric Investigation Of Effect Of Abnormal Process Conditions On Self-Piercing Riveting, Taek-Eon Jeong, Dong-Hyuck Kam, Cheolhee Kim

Mechanical and Materials Engineering Faculty Publications and Presentations

Self-piercing riveting (SPR) is one of the mechanical joining processes, and its application to Al/Fe dissimilar materials combination, which is hard to weld, is expanding in the automotive industry. The main process parameters in SPR are types of rivet and die, setting force, and rivet setting speed. Previously, the relationship between the main process parameters and output parameters such as cross-sectional characteristics and joint strength has been studied to optimize the SPR process. In practical applications, there are unexpected and abnormal process conditions such as poor fit-up, angular misalignment, edge offset distance, and inaccurate setting and pre-clamping forces, and their …