Engineering Commons^™

Expression, Purification, And Characterization Of Recombinant Basic Fibroblast Growth Factor In Pichia Pastoris, Henry Hieu Minh Le

University of the Pacific Theses and Dissertations

Wounds in the mouth, occurring after oral surgery, take time to heal. No ointment can be added to help with the healing process because mouth saliva will constantly wash it away. In order to combat this problem, we propose engineering a normal flora microbe to grow at the site of injury and secrete a recombinant growth factor to promote healing of the damaged tissue. Our goal is to have the yeast Pichia pastoris produce human basic fibroblast growth factor (bFGF), which aids in cellular proliferation. P. pastoris is a good choice for this application because not only is it considered …

Near Miss Reporting: Perspectives On Worker Conversance Of Incident Events Across Two Industries, Julia Mcgee

University of the Pacific Theses and Dissertations

The practice of reporting workplace incident events is adopted as best practice by organizations and complies with Occupational Safety and Health Administration (OSHA) mandates. Reporting the near miss incident type in which no injury or damage to equipment or the environment occurs is buttressed by the assumption that both the worker and the organization ascribe to the same goal to identify workplace hazards and prevent incident recurrence. The goal of incident reporting is not apparent, and the path to achieving the goal is obstructed by internal and external hazards that act to oppose the reporting process, such that the goals …

Hardware Security In Carbon Based Digital Integrated Circuits, Ahmed Abdelaziz

All ETDs from UAB

Carbon based integrated circuits (ICs) built with Carbon Nanotube Field Effect Transistor (CNTFET) and Graphene Nanoribbon Field Effect Transistor (GNRFET) are established as viable replacement for Silicon based Metal Oxide Semiconductor Field Effect Transistors (MOSFET) in order to meet the demands of future high density ICs with sub-nm channel lengths. Given the inevitability of such development, it is important to establish an understanding of the security vulnerabilities in Carbon based ICs. In this work, we have studied the important hardware security vulnerabilities that plague current MOSFET technology, in CNTFET and GNRFET based ICs. Based on our studies on hardware Trojans …

Spun Prestressed Concrete Pole Options As An Alternative To Wood Utility Distribution Poles, Paula Alvarez Alvarez Pino

All ETDs from UAB

The purpose of this research project is to analyze the current state-of-the-art, including use and design practices, of utility distribution poles and to evaluate the performance of spun prestressed concrete poles with different reinforcement schemes as a viable alternative to wood utility poles. There are an estimated 185 million utility distribution poles in place in the United States, and over 130 million are made out of wood. Most of the existing distribution poles are now approaching or have surpassed their useful lives since they were designed with a life expectancy of 50 years and were installed in the 1950s and …

Accessibility And Decay Of Web Citations In Computer Science Journals, Mohsen Jalali

Library Philosophy and Practice (e-journal)

The aim of this research is to scrutiny the accessibility and decay of web citations (URLs) used in refereed articles published by 27 Computer Science open access journals as indexed by Scopus. To do this, at first, we downloaded 1000 articles of Computer Science open access journals from 2009 to 2018. After acquiring articles, their web citations are extracted and analyzed from the accessibility and decay point of view. Moreover, for initially missed web citations complementary pathways such as using Google search engine are employed. Then, data collected are analyzed using descriptive statistical methods. Research findings indicated that 80.7% of …

Improving Base Metal Electrowinning, Charles Ebenezer Abbey

Doctoral Dissertations

"In zinc electrowinning, Mn oxidizes to form MnO₂ on Pb-Ag anodes, cell walls and pipes. MnO₂ reduces anode corrosion but also leads to short circuits and maintenance issues. MnO₂ is thought to interact with chloride ions and produce oxidized chlorine species. The interactions between Mn and Cl are not well understood. Bench scale experiments were conducted to investigate the effects of the manganese to chloride ratio on anode corrosion rate and electrolyte chemistry using rolled Pb-Ag anodes. Increasing the average Mn/Cl^- ratio from ~7:1 to ~11:1 reduced the anode corrosion rate. Anode scales produced with Mn/Cl …

Transient Multiphase Flow Simulation For Unloading Of Frac Hit Gas Wells, Miguel Angel Cedeno Moreno

Doctoral Dissertations

"This work seeks to develop a fully step-by-step transient multiphase flow simulation valid for unloading gas wells using nitrogen. It studies the behavior of nitrogen for unloading horizontal gas wells with gas injection in the annulus. The work investigates unloading non-Newtonian fluids such as those which invade offset wells when a frac hit occurs during hydraulic fracturing operations in unconventional wells. The effect of varying tubing depth and injection pressure are included in the study.

Results show that as the plastic viscosity increases, the nitrogen volume and time to unload will be increased. As tubing depth increases, the nitrogen volume …

The Effects Of Low Aspect Ratio And Heat Exchanging Internals On The Bubble Properties And Flow Regime In A Pilot-Plant Bubble/Slurry Bubble Column For Fischer-Tropsch Synthesis, Hayder Al-Naseri

Doctoral Dissertations

"Fischer-Tropsch synthesis (F-T) is a process utilized to convert the syngas mixture of CO and H₂ to synthetic fuel and chemicals that executed commercially by using the bubble/slurry bubble column reactor. The experimental results reveal that the investigated parameters, in terms the presence of internals, and reducing the aspect ratio and the solids loading, increase the local gas holdup, interfacial area, bubble passage frequency, and decrease the bubble rise velocity, bubble chord length. Meanwhile, the aspect ratio H/D = 4, and 5 provide enough height to established the fully developed flow regime. As a result of the variation in …

Ferrite Characterization Techniques & Particle Simulations For Semiconductor Devices, Nicholas Erickson

Doctoral Dissertations

"This dissertation is divided into three papers, covering two major topics. The first topic, techniques for ferrite characterization, is discussed over the course of two papers. The second topic, particle simulations for semiconductor devices, is discussed in the last paper. In the first paper, the method for extracting permeability from ferrite materials is discussed for the Keysight 16454A permeability extraction fixture, where the ferrite material to be characterized is assumed to be homogeneous. Then the method is updated to account for layered materials. The updated method is verified through full-wave simulations. In the second paper, a planar printed circuit board …

Chemically-Bonded Enamel-Coated Steel Pipelines For Corrosion Protection And Flow Efficiency, Liang Fan

Doctoral Dissertations

"This study is to explore and develop chemically-bonded enamel coating (200-300 um) on steel pipes, when subjected to soil and thermal environments, in order to improve the corrosion protection and safety of hazardous liquid and natural gas pipelines while reducing pressure loss. Out of five types of enamels and their various mixtures, Tomatec slurry and GP2118 powder were selected for steel pipeline applications. They were applied at approximately 810 °C to the inside surface of steel pipes in wet and electrostatic processes, respectively. The thickness and surface roughness of the enamel coating were measured using a gauge and an optical …

Hardware Architectures For Compact Microwave And Millimeter Wave Cameras, Matthew Jared Horst

Doctoral Dissertations

"Millimeter wave SAR imaging has shown promise as an inspection tool for human skin for characterizing burns and skin cancers. However, the current state-of-the-art in microwave camera technology is not yet suited for developing a millimeter wave camera for human skin inspection. Consequently, the objective of this dissertation has been to build the necessary foundation of research to achieve such a millimeter wave camera. First, frequency uncertainty in signals generated by a practical microwave source, which is prone to drift in output frequency, was studied to determine its effect on SAR-generated images. A direct relationship was found between the level …

Detection And Elimination Of Rock Face Vegetation From Terrestrial Lidar Data Using The Virtual Articulating Conical Probe Algorithm, Kenneth John Boyko

Doctoral Dissertations

"A common use of terrestrial lidar is to conduct studies involving change detection of natural or engineered surfaces. Change detection involves many technical steps beyond the initial data acquisition: data structuring, registration, and elimination of data artifacts such as parallax errors, near-field obstructions, and vegetation. Of these, vegetation detection and elimination with terrestrial lidar scanning (TLS) presents a completely different set of issues when compared to vegetation elimination from aerial lidar scanning (ALS). With ALS, the ground footprint of the lidar laser beam is very large, and the data acquisition hardware supports multi-return waveforms. Also, the underlying surface topography is …

Time-Dependent Reliability Methodologies With Saddlepoint Approximation, Zhangli Hu

Doctoral Dissertations

"Engineers always encounter time-dependent uncertainties that ubiquitously exist, such as the random deterioration of material properties and time-variant loads. Therefore the reliability of engineering systems becomes time-dependent. It is crucial to predict the time-dependent reliability in the design stage, given possible catastrophic consequences of a failure. Although extensive research has been conducted on reliability analysis, estimating the reliability accurately and efficiently is still challenging. The objective of this work is to develop accurate and efficient reliability methodologies for engineering design. The basic idea is the integration of traditional reliability methods with saddlepoint approximation (SPA), which can accurately approximate the tail …

Reliability Analysis For Systems With Outsourced Components, Zhengwei Hu

Doctoral Dissertations

"The current business model for many industrial firms is to function as system integrators, depending on numerous outsourced components from outside component suppliers. This practice has resulted in tremendous cost savings; it makes system reliability analysis, however, more challenging due to the limited component information available to system designers. The component information is often proprietary to component suppliers. Motivated by the need of system reliability prediction with outsourced components, this work aims to explore feasible ways to accurately predict the system reliability during the system design stage. Four methods are proposed. The first method reconstructs component reliability functions using limited …

Assessment And Prediction Of Surface Water Vulnerability From Non-Point Source Pollution In Midwestern Watersheds, Fadhil K. Jabbar

Doctoral Dissertations

"Non-point source pollution is the leading cause of impairment in surface water in the Midwest. In this research, we seek to predict which watersheds are most vulnerable to point source pollution without field sampling using publically available GIS databases. Watersheds with higher vulnerability ratings can then be targeted for water quality monitoring, and funds used to improve watershed health can be distributed with greater efficacy. To better understand and target watershed vulnerability, we used three different approaches. In the first project, 35 sub-watersheds were sampled in the Lower Grand Watershed, which is a highly agricultural watershed in northern Missouri/southern Iowa. …

Laser Welding Of Metallic Glass To Crystalline Metal In Laser-Foil-Printing Additive Manufacturing, Yingqi Li

Doctoral Dissertations

"The application of metallic glasses has been traditionally limited to parts with small dimensions and simple geometries, due to the requirement of fast cooling during the conventional process of casting. In addition, joining metallic glass to crystalline metal is of interest for many applications that require locally tailored functions and properties, but it is challenging. This research describes a promising additive manufacturing technology, i.e., laser-foil-printing, to make high-quality metallic glass parts with large dimensions and complex geometries and to fabricate multi-material components from metallic glass and crystalline metal. In this research, Zr_52.5Ti₅Al₁₀Ni_14.6Cu …

Freeform Extrusion Fabrication Of Advanced Ceramics And Ceramic-Based Composites, Wenbin Li

Doctoral Dissertations

"Ceramic On-Demand Extrusion (CODE) is a recently developed freeform extrusion fabrication process for producing dense ceramic components from single and multiple constituents. In this process, aqueous paste of ceramic particles with a very low binder content ( < 1 vol%) is extruded through a moving nozzle to print each layer sequentially. Once one layer is printed, it is surrounded by oil to prevent undesirable water evaporation from the perimeters of the part. The oil level is regulated just below the topmost layer of the part being fabricated. Infrared radiation is then applied to uniformly and partially dry the top layer so that the yield stress of the paste increases to avoid part deformation. By repeating the above steps, the part is printed in a layer-wise fashion, followed by post-processing. Paste extrusion precision of different extrusion mechanisms was compared and analyzed, with an auger extruder determined to be the most suitable paste extruder for the CODE system. A novel fabrication system was developed based on a motion gantry, auger extruders, and peripheral devices. Sample specimens were then produced from 3 mol% yttria stabilized zirconia using this fabrication system, and their properties, including density, flexural strength, Young's modulus, Weibull modulus, fracture toughness, and hardness were measured. The results indicated that superior mechanical properties were achieved by the CODE process among all the additive manufacturing processes. Further development was made on the CODE process to fabricate ceramic components that have external/internal features such as overhangs by using fugitive support material. Finally, ceramic composites with functionally graded materials (FGMs) were fabricated by the CODE process using a dynamic mixing device"--Abstract, page iv.

Solvent-Free Additive Manufacturing Of Electrodes For Li-Ion Batteries, Brandon Joshua Ludwig

Doctoral Dissertations

"A new Li-ion battery electrode manufacturing process using a solvent free additive manufacturing method has been developed. Li-ion battery electrodes consist of active material particles, a binder additive, and a conductive additive. Traditionally, Li-ion battery electrodes are manufacturing using the "slurry casting" technique. In this method, the electrode materials are mixed with a solvent to create a slurry. Electrodes fabricated in this method are readily implemented for small platforms, such as portable electronics. However, this method isn't as economically viable in large platforms due to high material and manufacturing costs. High material and manufacturing costs are mostly attributed to the …

Techno-Economic Optimization And Environmental Life Cycle Assessment Of Microgrids Using Genetic Algorithm And Artificial Neural Networks, Prashant Nagapurkar

Doctoral Dissertations

"This dissertation focuses primarily on techno-economic optimization and environmental life cycle assessment (LCA) of sustainable energy generation technologies. This work is divided into five papers. The first paper discusses the techno-economic optimization and environmental life cycle assessment of microgrids located in the USA using genetic algorithm. In this paper, a methodology was developed that assessed the techno-economic and environmental performance of a small scale microgrid located in US cities of Tucson, Lubbock and Dickinson. Providing uninterrupted power the microgrid was composed of seven components -- solar photovoltaics, wind-turbines, lead acid batteries, biodiesel generators, fuel cells, electrolyzers and H₂ tanks. …

Quantifying Restoration Costs In The Aftermath Of An Extreme Event Using System Dynamics And Dynamic Mathematical Modeling Approaches, Akhilesh Ojha

Doctoral Dissertations

"Extreme events such as earthquakes, hurricanes, and the like, lead to devastating effects that may render multiple supply chain critical infrastructure elements inoperable. The economic losses caused by extreme events continue well after the emergency response phase has ended and are a key factor in determining the best path for post-disaster restoration. It is essential to develop efficient restoration and disaster management strategies to ameliorate the losses from such events. This dissertation extends the existing knowledge base on disaster management and restoration through the creation of models and tools that identify the relationship between production losses and restoration costs. The …

Development Of Lidar Assisted Terrestrial Radar Interferometry For Rock Deformation Monitoring, Ricardo Javier Romero Ramirez

Doctoral Dissertations

"Rock and soil slope movements cost millions of dollars annually. During the past few decades, engineers have relied on traditional methods to detect slope movements. These tools are valuable for small spatial areas but, may not be adequate or cost effective for large spatial areas. Remote sensing methods such as terrestrial laser scanning (TLS) and terrestrial radar interferometry (TRI) provide excellent spatial coverage, and with adequate post-data-processing software, sub-millimetric scale deformation sensitivity can be achieved.

This work will present a comparative experimental study between TLS and TRI. The comparative experimental study will allow us to achieve the two main objectives …

Pressure Versus Impulse Graph For Blast-Induced Traumatic Brain Injury And Correlation To Observable Blast Injuries, Barbara Rutter

Doctoral Dissertations

"With the increased use of explosive devices in combat, blast induced traumatic brain injury (bTBI) has become one of the signature wounds in current conflicts. Animal studies have been conducted to understand the mechanisms in the brain and a pressure versus time graph has been produced. However, the role of impulse in bTBIs has not been thoroughly investigated for animals or human beings.

This research proposes a new method of presenting bTBI data by using a pressure versus impulse (P-I) graph. P-I graphs have been found useful in presenting lung lethality regions and building damage thresholds. To present the animal …

Investigating Blast Fume Propagation, Concentration And Clearance In Underground Mines Using Computational Fluid Dynamics (Cfd), Raymond Ninnang Tiile

Doctoral Dissertations

"Blasting activities using standard industry explosives is an essential component of underground hard rock mining operations. Blasting operations result in the release of noxious gases, presenting both safety and productivity threats. Overestimation of post-blast re-entry time results in production losses, while underestimation leads to injuries and fatalities. Research shows that most underground mines simply standardize post-blast re-entry times based on experiences and observations. Few underground mines use theoretical methods for calculating post-blast re-entry time. These theoretical methods, however, are unable to account for the variations in the blasting conditions. Literature review shows that: (i) there is currently no means of …

Plugging Performance Of Preformed Particle Gels In Fractures And Its Influencing Factors, Ze Wang

Doctoral Dissertations

"Preformed particle gels (PPG) has been successfully applied to combat the water channeling caused by fractures or fracture-like channels. Understanding the placement and plugging of PPG in fractures is crucial for gel treatment design. The objective of the dissertation is to explore the plugging performance of three PPG products in two types of fracture models, the partially and fully open fractures. The following studies has been conducted and conclusions have been drawn based on the results and analysis. First, the placement and plugging performance of conventional PPG was investigated using core flooding experiments conducted partially open fractures. The plugging efficiency …

Experimental Investigation Of Liquid Contact In The Developing Post-Dryout Chf Flow Boiling Regime Using Surface Mounted Thermistors, Hiralkumar Harshadbhai Patel

Doctoral Dissertations

"Understanding heat transfer in the post-critical heat flux (CHF) flow boiling regime is important for determining the performance of the heat transfer equipment for various industrial applications requiring high heat transfer rates, e.g., heat exchangers, boilers, chemical and nuclear reactors. Liquid can be present in the core of the flow channel in the form of entrained liquid droplets, especially immediately downstream of film dryout. These droplets are suspected to provide an important heat transfer mechanism as they impinge on the heated wall. The objective of the current study is to investigate liquid contact with the heated wall in this flow …

Developing And Evaluating A Partition-Cavity Solar Thermochemical Reactor For Syngas Production Via Computational Fluid Dynamics, Han Zhang

Doctoral Dissertations

"Solar thermochemical processes are attractive since they have the advantages of storing solar energy as chemical fuels. In this dissertation, a partition-cavity solar thermochemical reactor was developed, and the heat and mass transfer of the solar thermochemical processes were numerically analyzed in this directly-irradiated reactor.

The reduction reaction of two-step CeO₂/CeO_2-δ solar redox process was investigated using the coupling of computational fluid dynamics (CFD) and discrete element method (DEM). The reduction rate was studied based on the catalyst textual properties and the reaction condition. The results revealed that the increase of catalyst specific surface area and the …

Building Shared Knowledge For Eor Technologies: Screening Guideline Constructions, Dashboards, And Advanced Data Analysis, Na Zhang

Doctoral Dissertations

"Successful implementation of enhanced oil recovery (EOR) technology requires comprehensive knowledge and experiences based on existing EOR projects. EOR screening guidelines and EOR reservoir analog are served as such knowledge which are considered as the first step for a reservoir engineer to determine the next step techniques to improve the ultimate oil recovery from their assets. The objective of this research work is to provide better assistance for EOR selection by using fundamental statistics methods and machine learning techniques.

In this dissertation, a total of 977 worldwide EOR projects with the most uniformed, high-quality, and comprehensive information were collected from …

Oxide Inclusion Evolution And Factors That Influence Their Size And Morphology, Obinna M. Adaba

Doctoral Dissertations

"The evolution of oxide inclusion size distribution and the shape of the distribution during steelmaking and casting and the process variables that influence the inclusion characteristics at different stages were investigated and documented. A statistical method for transforming the 2D size distribution to their actual 3D distributions and the application of a kinetic model to determine nucleation and growth mechanisms were tested. Finally, laboratory experiments were performed to study the effects of preexisting inclusions, steel active oxygen content, and supersaturation on the size and morphology of Al₂O₃ inclusions.

The inclusion size, composition, and morphology following steel deoxidation …

Underwater Acoustic Communications And Adaptive Signal Processing, Mohammadhossein Behgam

Doctoral Dissertations

"This dissertation proposes three new algorithms for underwater acoustic wireless communications. One is a new tail-biting circular MAP decoder for full tail-biting convolution (FTBC) codes for very short data blocks intended for Internet of Underwater Things (IoUT). The proposed algorithm was evaluated by ocean experiments and computer simulations on both Physical (PHY) and Media access control (MAC) layers. The ocean experimental results show that without channel equalization, the full tail-biting convolution (FTBC) codes with short packet lengths not only can perform similarly to zero-tailing convolution (ZTC) codes in terms of bit error rate (BER) in the PHY layer. Computer simulation …

Electrodeposition Of Epitaxial Metal Thin Films On Silicon For Energy Conversion And Flexible Electronics, Qingzhi Chen

Doctoral Dissertations

"This research focuses on epitaxial electrodeposition of two coinage metals: Au and Ag thin films on the silicon surface and their applications in flexible electronics and energy conversion and storage. The first paper: Photoelectrochemistry of ultrathin, semi-transparent, and catalytic gold films electrodeposited epitaxially onto n-silicon (111) describes the epitaxial electrodeposition of Au thin films on n-type Si using a simple HAuCl4 bath and the photoelectrochemical properties of the Au-Si junction barrier. The effect of the Au layer on the interfacial energetics as well as the stability of the photoelectrode as a function of the Au coverage/thickness is determined in a …