Engineering Commons^™

A Blockchain-Enabled Peer-To-Peer Energy Trading Platform For Managing Complex Exchange Of Kilowatt-Hours And Negawatts, Murat Kuzlu, Rasheq Rahman, Jason Lin

Engineering Technology Faculty Publications

Under the Department of Energy’s STTR funding, BEM Controls LLC performed research from July 2, 2018 to April 1, 2019. The purpose of this research was to design, develop and demonstrate the technical feasibility of the blockchain enabled energy trading platform for managing complex exchange of kilowatt hours and negawatts. The energy trading platform was developed in the open-source HyperLedger Fabric blockchain framework and the performance of the blockchain network was evaluated. Key research findings and results include (1) the successful design and development of an open-architecture blockchain-based energy trading platform able to execute smart contract transactions across eight use …

1995-2005: A Decade Of Innovation In Low Temperature Plasma And Its Applications, Mounir Laroussi

Electrical & Computer Engineering Faculty Publications

Scientific breakthroughs tend to come in spurts when unique societal, economical, and political circumstances conspire (knowingly or unknowingly) and create an environment ripe for creativity. The field of low temperature plasma (LTP) recently experienced such an upheaval, which this paper attempts to relate in some details. There have been “roadmap” papers published before, which look towards the future of the field, but all roads start somewhere and even “new” roads are often paved over older roads that were discovered and traveled by early pioneers. With the sharp decrease in funding for fusion research in the USA in the early 1990s …

Carbon Multicharged Ion Generation From Laser-Spark Ion Source, Md. Mahmudur Rahman, Oguzhan Balki, Hani E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Multicharged carbon ions are generated by using a laser-assisted spark-discharge ion source. A Q-switched Nd:YAG laser pulse (1064 nm, 7 ns, ≤ 4.5 × 10⁹ W/cm²) focused onto the surface of a glassy carbon target results in its ablation. The spark-discharge (∼1.2 J energy, ∼1 µs duration) is initiated along the direction of the plume propagation between the target surface and a grounded mesh that is parallel to the target surface. Ions emitted from the laser-spark plasma are detected by their time-of-flight using a Faraday cup. The ion energy-to-charge ratio is analyzed by a three-mesh retarding field …

Natural Resources Governance Employing Blockchain-Based Decision-Making, Farinaz Sabz Ali Pour, Adrian Gheorghe

Engineering Management & Systems Engineering Faculty Publications

Natural resources are essential structures of socio-economic systems which shape the well-being of humanity, environment, and the economy. Human actions have become the critical responsibility for environmental changes and pressuring many planetary boundaries. Having a systematic approach can provide a governance platform including the inherent characteristics of the resource, the historically established form of use, and transaction costs. A natural resource governance framework is developed by applying Blockchain technology as the primary goal of this study to regulate and manage the extraction and trades. Blockchain technology provides a distributed concurrency monitoring system for sustainable resource management. Persistent and pervasive cooperation …

Sems Says...: We Welcome Your Feedback, Brian K. Smith, Chinweike Eseonu, Sreekanth Ramakrishnan, Pilar Pazos-Lago

Engineering Management & Systems Engineering Faculty Publications

The article offers information on the IISE Annual Conference Expo 2019 to be held on May 18-21, 2018 in Orlando, Florida, for industrial and systems engineers.

Leveraging Contracting Strategies With Private Shipyards For Increasing Naval Fleet Operational Availability, Kaitlynn M. Castelle, Joseph M. Bradley, Sanjeev Gupta

Engineering Management & Systems Engineering Faculty Publications

A major rethink of NAVSEA’s shipyard contracting strategy is required to support the critical need of improving our naval fleet availability. Operational Fleet material availability is reduced when various parts of the “NAVSEA production system” operate at cross-purposes. By increasing alignment between major players (i.e., NAVSEA and the private shipyards), major improvements in delivery performance, cost, and even throughput can be realized. Developing strategies and specific actions to do so is a rich field given the current state of the system. We take an analytical as well as evidence-based approach to propose strategies that can be successful given the peculiar …

On Hybrid Temporal Basis Functions For Stable Numerical Solution Of Time Domain Boundary Integral Equations, Fang Q. Hu

Mathematics & Statistics Faculty Publications

Problems in unsteady aerodynamics and aeroacoustics can sometimes be formulated as integral equations, such as the boundary integral equations. Numerical discretization of integral equations in the time domain often leads to so-called March-On-in-Time (MOT) schemes. In the literature, the temporal basis functions used in MOT schemes have been largely limited to low-order shifted Lagrange basis functions. In order to evaluate the accuracy and effectiveness of the temporal basis functions, a Fourier analysis of the temporal interpolation schemes is carried out. Based on the Fourier analysis, the spectral resolutions of various temporal basis functions are quantified. It is argued that hybrid …

The Impact Of Extreme Virtual Elevation Above Grade On Construction Workers' Physiological Responses, Physical Responses, And Task Performance, Mahmoud Habibnezhad

Department of Construction Engineering and Management: Dissertations, Theses, and Student Research

On average, in every two work hours, one person dies from work-related injuries at construction sites. Most incidents are due to falling from elevated surfaces. Slips, trips, and loss of balance are the main causes. Studies suggest that instigating visual mismatch and physiological changes are among the most important reasons behind falling from narrow elevated surfaces. By using advanced virtual reality models, this dissertation aims to highlight some of the possible effects of a destabilizing environment (i.e., elevation above grade) on workers’ physiological responses and task performance. More specifically, this dissertation strives to find potential effects of elevation above grade …

Stress State Analysis And Tensile-Shear Fracture Criterion In Combined Puncture And Cutting Of Soft Materials, Ennouri Triki, Chantal Gauvin

Études primaires

The mechanics of the combined puncture and cutting of protective materials by a pointed blade are studied theoretically and experimentally, by means of stress state analysis. Through analysis of the stresses occurring during the puncture cutting of a variety of neoprene and nitrile rubber membranes by pointed blades with different cutting-edge angles, a force state of pushing/shear-dependent loading is formulated and discussed. By considering this combined loading as an asymmetric fracture, two equations—for pushing force component and shear force component—are then derived from the stress intensity factors. From this stress analysis, a model based on fracture mechanics theory is developed …

Procure-To-Pay Software In The Digital Age: An Exploration And Analysis Of Efficiency Gains And Cybersecurity Risks In Modern Procurement Systems, Drew Lane

MPA/MPP/MPFM Capstone Projects

Procure-to-Pay (P2P) softwares are an integral part of the payment and procurement processing functions at large-scale governmental institutions. These softwares house all of the financial functions related to procurement, accounts payable, and often human resources, helping to facilitate and automate the process from initiation of a payment or purchase, to the actual disbursal of funds. Often, these softwares contain budgeting and financial reporting tools as part of the offering. As such an integral part of the financial process, these softwares obviously come at an immense cost from a set of reputable vendors. In the case of government, these vendors mainly …

Employing 2-D Cfd & Lrb Model Around Trees To Improve Vawt Placement, David Chukwuebuka Bassey

All Graduate Theses, Dissertations, and Other Capstone Projects

In the placement of vertical axis wind turbines, trees are a constant presence in the vicinity. They are found to grow at different height and shape configurations. And in areas such as the Minnesota State University, Mankato (MNSU) campus, they serve as blockage to airflow; limiting the efficiency of installed turbines. This work sets the precedent for the validation of vegetative numerical models created for the Xcel Energy Research Development Fund (RDF) project.

Using two-dimensional (2-D) numerical simulations of porous cylinders placed in a rectangular medium of air, insight into the flow profile and distribution in the leeward side of …

Study Of American Wood Pellet Stove Emissions, Sergio Gamarra

All Graduate Theses, Dissertations, and Other Capstone Projects

Problem: The EPA (Environmental Protection Agency) had not specified emissions performance standards for pellet burning stoves. Instead they were lumped in with cordwood burning stoves. IRETI’s decision to pursue this baseline study was guided by Minnesota’s concurrent “2025 Energy Action Plan” and the EPA’s pellet stove testing method development. Wood pellet fuel, a renewable resource, and the technology developed to utilize it for residential heating should be further studied to examine how together they both stand up to newly developed EPA emissions testing methods. This will establish a benchmark for testing American technology, thus guiding IRETI’s efforts of introducing foreign …

Developing Framework For The Implementation Of Advanced Manufacturing Technologies In Small And Medium-Sized Enterprises, Dattatraya V. Bhise, Vivek K. Sunnapwar

International Journal of Applied Management and Technology

Intense competition, demanding customers, and shortening product life cycles are prompting small- and medium-sized enterprises to invest in advanced manufacturing technologies (AMTs). Small manufacturers often depend on large manufacturers for orders and so require design as well as manufacturing flexibility on their part. One way of achieving the flexibility is through adoption of AMTs. The decision to invest in AMT is a major decision and thus requires proper consideration to all the aspects of the implementation process before a final commitment is made. Although the technical capabilities of AMTs are well proven, neither practitioner nor academics agree upon a framework …

Testing And Validation Framework For Closed-Loop Physiology Management Systems For Critical And Perioperative Care, Farooq M. Gessa

Master’s Theses

The research aims at developing a framework for testing systems such as closed-loop physiology management systems to ensure that they are safe and effective for use with patients. Building medical devices that are both robust and safe is a challenge. There has been a tremendous increase in modernization and innovation of various medical systems but many of these systems either fail trials or are recalled due to safety issues.

Medical operation rooms require care teams responsible for monitoring the patients and other technical surgical devices. The care process requires a balancing administration that takes care of the drugs and fluids …

Development Of Physics Based Machine Learning Algorithms, Rob Jennings

Master’s Theses

In this study, a baseball pitch was examined to try to understand its behavior, and make a predictive model of it. A baseball pitch was tested experimentally with a wind tunnel and modeled computationally with COMSOL CFD software. Five input variables (spin rate, sting angle, seam orientation: Y axis, seam orientation: Z axis, and air velocity) were controlled, with force in three axes recorded as outputs. The experimental and computational results were examined and seen to be interdependent for all input variables. Experimental and computational data were both insufficient for predicting system behavior. Experimental data collection would have required an …

Optical And Electrical Analysis Of Zno/Znte Micropillar Solar Cells, Sadia Binte Sohid

Master’s Theses

The prime focus of the energy-research community in recent times has been replacing fossil fuels with renewable energy. Therefore, photovoltaic research areas are rapidly expanding in this era. The purpose of this work is to compare three different structural ZnO/ZnTe solar cell types (planar, axial micropillar and radial micropillar). The best optical and electrical performance has been obtained by the radial junction (core-shell) ZnO/ZnTe micropillar solar cell due to its pillar structure and radial junction. The unique advantage of the radial junction micropillar is that the angle of the incident light and the carrier collection is orthogonal. Therefore, the pillar …

Solar Powered Atmospheric Water Generation, Ben Conser

Master’s Theses

Several atmospheric water generation (AWG) system configurations were analyzed to determine the feasibility of AWG as a method to combat water stress. In order to best combat water stress, AWG must be implemented in such a way which minimizes the energetic and monetary cost of water production. Thermodynamic and economic analyses were used to compare the performance of several AWG system configurations. Metrics such as specific energy consumption (SEC) and levelized cost of water (LCOW), which measure the energetic and monetary cost of water production respectively, were used to compare each system. Using this approach, the optimal system configuration was …

Analysis And Control Of Fiber-Reinforced Elastomeric Enclosures (Frees), Soheil Habibian

Master’s Theses

While rigid robots are extensively used in various applications, they are limited in the tasks they can perform and can be unsafe in close human-robot interactions. Soft robots on the other hand surpass the capabilities of rigid robots in several ways, such as compatibility with the work environments, degrees of freedom, manufacturing costs, and safe interactions with the environment. This thesis studies the behavior of Fiber-Reinforced Elastomeric Enclosures (FREEs) as a particular type of soft pneumatic actuator that can be used in soft manipulators. A dynamic lumped-parameter model is created to simulate the motion of a single FREE under various …

Image Analysis For Lung Cancer Diagnosis And Superresolution Localization Microscopy, Xia Huang

Open Access Theses & Dissertations

With the development of imaging analysis techniques, flurry of applications associated with it has been hatched. In this paper, image analysis on both organ and cellular levels will be demonstrated. For organ level images, a deep learning based computer aided lung cancer diagnosis based on computer tomography images is studied. Deep learning techniques have been extensively used in computerized pulmonary nodule analysis recent years. Many reported studies still utilized hybrid methods for diagnosis, in which convolutional neural networks (CNNs) are used only as one part of the pipeline, and the whole system still needs either traditional image processing modules or …

Structures And Daq System For The Lox/Lch4 500 And 2000 Lbf. Rocket Engines, Rachel Pilgrim

Open Access Theses & Dissertations

With the progression of space exploration and research, new alternative fuels and fuel combinations have been discovered. The ability to produce methane from Mars' atmosphere and oxygen from Mars' regolith has led to the two becoming a great alternative propellant combination for rocket propulsion systems. To further advance LOX/LCH4 propulsion systems, a 500 and 2000 lbf rocket engine were designed and manufactured and are to be launched from the MIRO cSETR Technology Research and Innovation Acceleration Park (tRIAc) in Fabens, Texas for data collection and analysis. The objective of this thesis is to give a thorough overview of the static …

Structural Design Of Complex Components, Armando Antonio Ochoa

Open Access Theses & Dissertations

The University of Texas at El Paso (UTEP) and the Center for Space Exploration and Technology Research (cSETR) is determined to develop a launch vehicle that is made completely of additive manufacturing materials, has the capability to transport a 100 lb payload to low earth orbit (LEO) as well as completing the design of a strucutral steel mobile launch stand that has the capability of withstanding the launch vehicle's static and dynamic loadings. The project will consist of carbon composite components to reduce weight while maintaining efficiency, strucutral steel components to resist extreme loadings and maintain strucutral shape, and lastly …

Exploration And Optimization Of Biomaterials And Cells Required For The Fabrication Of A "Cardiac Patch", Shweta Anil Kumar

Open Access Theses & Dissertations

Cardiac failure induced by myocardial infarction is believed to be one of the primary causes of morbidity and mortality all over the world. Affecting more than 26 million people worldwide, its prevalence has been observed to increase steadily. Myocardial infarction, which intitially begins as the occlusion of of a coronary artery, results in the death of millions of cardiomyocytes by obstructing blood flow to the serviced regions of the myocardium. The dead myocardium is replaced by a dense,collagenous scar which reduces the contractility of the heart, gradually leading to heart attacks. Most of the existing treatment therapies are palliative in …

Quantifying Early-Age Concrete Mechanical Properties And Curing Conditions Utilizing An Automated System, Benjamin Arras

Open Access Theses & Dissertations

The validation of concrete quality based on the 28-day strength is a lengthy process. Predicting concrete mechanical properties through early-age methods can streamline the construction process. Early-age concrete behavior consists of assessing the concrete curing as-related to setting stages, the hydration process, strength and stiffness development, while considering various environmental system parameters. This paper reports on a nondestructive method for observing the early-age strength and modulus development of concrete mixes over seven days in a controlled, laboratory setting. An apparatus was designed and built for continuous acquisition of seismic modulus data (using free-free resonant column) and heat of hydration/maturity information …

Bioprinted Mcf7 Breast Cancer Cells, An In Vitro Model For Drug Discovery, Aleli Campbell

Open Access Theses & Dissertations

Current breast cancer treatments are successful in eradicating this disease in the majority of patients, though there are quite a few cases where relapse or recurrence follow, which may lead to continued cancer therapy or death. Thermal inkjet bioprinting (BP) is a novel technique that is used to bioprint biomaterials or diverse cellular organisms to engineer tissue or organ models in vitro. In this Dissertation, we investigated the molecular effect of BP MCF7 breast cancer cells (BCC), cell survival of the cells when exposed to FDA approved systemic therapy alone and in combination with radiation and lastly, the ability of …

A Modified Wilshire Model For Creep Deformation And Damage Prediction, Jaime Aaron Cano

Open Access Theses & Dissertations

In this work, a new constitutive model, the WCS model, is derived that combines the Wilshire equations with continuum damage mechanics (CDM) for the long-term prediction of creep deformation, damage, and rupture. Long-term creep data is expensive and time-consuming to obtain because conventional creep testing is real-time. There is a need to extrapolate long-term creep behaviors from short-term data. Models that can accurately predict long-term creep behavior over a wide range of boundary conditions are vital for design engineers. The classic Wilshire equations can accurately extrapolate the long-term stress-rupture, minimum-creep-strain-rate, and time-to-strain of various alloys as their functional form has …

Assessing Spatiotemporal Exposures To Transportation Pollutants In Near-Road Communities Using Aermod, Mayra Consuelo Chavez

Open Access Theses & Dissertations

Traffic-related air pollution has a profound impact on human health especially for residents living in near-road communities which are constantly exposed these air pollutants. A near-road community is expected to observe significant spatial and temporal variations in pollutant concentrations, as air pollution resulting from emissions from major highways decreases rapidly from the highway. This research conducted on-site traffic and air quality measurements on four critical transportations related air pollutants, PM2.5, PM10, NO2, O3, as well as emission and air dispersion modeling of transportation emission impacts in a near-road community. Using numerical models provided by the EPA, integrated with field measurements …

A Method For Iron Determination During Copper Electrometallurgy And Its Application To The Calculation Of Current Efficiency, Daniel Pedro Cruz

Open Access Theses & Dissertations

With the objective of developing statistical models that describe iron kinetics under typical copper electrolytes as well as its effects on current efficiency and influence in cathodic and anodic behavior, a detailed electrochemical analysis is done in this work as a contribution to implement hydrometallurgical processes in the refining or winning process to produce high purity copper.

This Thesis evaluates the oxidation-reduction potential (ORP) of the Fe3+/Fe2+ couple in the H2SO4-Fe2(SO4)3-FeSO4-H2O and H2SO4-CuSO4-Fe2(SO4)3-FeSO4-H2O systems, with addition of different copper concentrations and temperatures up to 70°, typically employed in the industry. This study further validates and expands a thermodynamic expression developed …

Development Of An Ionic Green Monopropellant 1 Newton Thruster For Small Satellite Application, Jaclyn Mona Mejia

Open Access Theses & Dissertations

In effort to advance green monopropellant propulsion using AF-M315E, a 1N thruster was developed to demonstrate the propellant capabilities for low thrust requirement missions. The current study presents the development of a 1 Newton thruster. The thruster was designed based on available literature for initial parameters. In house developed catalyst was packed into the 1 Newton thruster, and mounted onto a thrust stand for testing. Two configurations of catalyst were used for this testing campaign. As a result, temperature peaks from AF-M315E decomposition gases reached up to 1400°C with an iridium loading factor of 25% by mass with both catalyst …

Platelet Biology And Thrombosis: Juul E-Cigarette Exposure And 5ht2a Receptor Drug Discovery, Jean Emmanuel Montes Ramirez

Open Access Theses & Dissertations

x

The Drones' Impact On Precision Agriculture, Ibrahim Naji

Open Access Theses & Dissertations

A study to assess the overall impact of drones in the agricultural sector. The specific goal of this research was to provide a drone system to ward off pestering birds from crops to allow for better growth and an increased yield. Along with providing a user-friendly coded drone system for farmers that is cost effective, this project has inspired other areas of use for the drone.