Engineering Commons^™

An Algorithm For Coupling Multibranch In Vitro Experiment To Numerical Physiology Simulation For A Hybrid Cardiovascular Model, Ehsan Mirzaei, Masoud Farahmand, Ethan Kung

Publications

The hybrid cardiovascular modeling approach integrates an in vitro experiment with a computational lumped‐parameter simulation, enabling direct physical testing of medical devices in the context of closed‐loop physiology. The interface between the in vitro and computational domains is essential for properly capturing the dynamic interactions of the two. To this end, we developed an iterative algorithm capable of coupling an in vitro experiment containing multiple branches to a lumped‐parameter physiology simulation. This algorithm identifies the unique flow waveform solution for each branch of the experiment using an iterative Broyden's approach. For the purpose of algorithm testing, we first used mathematical …

Generalized Ultrasonic Scattering Model For Arbitrary Transducer Configurations, Andrea P. Arguelles, Joseph A. Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Ultrasonic scattering in polycrystalline media is directly tied to microstructural features. As a result, modeling efforts of scattering from microstructure have been abundant. The inclusion of beam modeling for the ultrasonic transducers greatly simplified the ability to perform quantitative, fully calibrated experiments. In this article, a theoretical scattering model is generalized to allow for arbitrary source and receiver configurations, while accounting for beam behavior through the total propagation path. This extension elucidates the importance and potential of out-of-plane scattering modes in the context of microstructure characterization. The scattering coefficient is explicitly written for the case of statistical isotropy and ellipsoidal …

Incorporating Geophysical Data In Slope Stability Modeling For Two Slopes In Arkansas, Vanessa Lebow

Graduate Theses and Dissertations

Slope failures in the United States alone cause millions of dollars in damage to infrastructure, threaten national monuments, create environmental hazards, and take an average of 25-50 lives a year. With the inevitable construction that occurs on slopes, it is imperative that the slopes be properly designed which requires a thorough understanding of slope grade, subsurface soil conditions, soil strength parameters, water table locations, and depth to bedrock across the entire site. The preferred method of data collection would be to use borings and other in-situ methods; however, sometimes due to cost constraints or site accessibility only a very limited …

Evaluation Of Concrete Deck Curing Regimens Using Capillary Pressure Sensing System, Samuel Spann

Graduate Theses and Dissertations

Early-age plastic shrinkage cracking is a common problem with the construction of concrete bridge decks due to the high surface area-to-volume ratio and exposure to potentially detrimental environmental effects. Curing regimens are utilized to mitigate cracking risk during the plastic stage of the concrete; the curing regimens evaluated for this study were wet burlap-polyethylene sheeting, two acrylic curing compounds, and one lithium compound. Capillary pressure in the water filled pores has been shown to correlate to the plastic shrinkage cracking risk of concrete. A new portable system has been developed to measure the capillary pressure that could potentially be used …

Truck Activity Pattern Classification Using Anonymous Mobile Sensor Data, Taslima Akter

Graduate Theses and Dissertations

To construct, operate, and maintain a transportation system that supports the efficient movement of freight, transportation agencies must understand economic drivers of freight flow. This is a challenge since freight movement data available to transportation agencies is typically void of commodity and industry information, factors that tie freight movements to underlying economic conditions. With recent advances in the resolution and availability of big data from Global Positioning Systems (GPS), it may be possible to fill this critical freight data gap. However, there is a need for methodological approaches to enable usage of this data for freight planning and operations.

To …

Study Of Internal Strains Developed In Concrete Decks At Early Ages In Steel Continuous Bridges, Fernando R. Benitez Ortiz

Graduate Theses and Dissertations

The Arkansas Department of Transportation (ARDOT) has identified bridge deck cracking shortly after concrete decks are placed and prior to applying traffic loads. Previous researchers have confirmed improper construction practices and design methods can lead to deck cracking. Currently, many contractors throughout Arkansas are using continuous deck pours. This construction approach may restrict the concrete slab from movement during early age shrinkage, causing tensile stresses to develop. The final stresses at the end of construction must be lower than the concrete tensile strength, if not cracking issues will develop. Eventually, these cracks may enlarge due to service load stresses and …

Cytotoxicity And Mutagenicity Of Disinfection Byproduct Mixtures Formulated Using Free Chlorine And Monochloramine, Yonas Ghebremedhin

Graduate Theses and Dissertations

Bioassays have been used extensively to assess various toxicity endpoints of drinking water disinfection byproducts (DBPs), but an emphasis on single compounds prevails. In this research, DBP mixtures were assessed using a cytotoxicity test with Chinese Hamster Ovary (CHO) cells and an Ames fluctuation test with Salmonella typhimurium TA-98 and TA-100 with and without S9 rat liver homogenate. Seven whole mixture DBP concentrates were formulated using reconstituted natural organic matter (NOM) extracts from the Upper Mississippi River using scaled disinfectant dosing protocols with free chlorine and monochloramine in the presence and absence of added bromide. DBPs were identified by gas …

Weigh-In-Motion Auto-Calibration Using Automatic Vehicle Identification, Fu Ren Zhang Zhang Durandal

Graduate Theses and Dissertations

Weigh-in-Motion (WIM) sensors are installed on mainline lanes at highway locations to record vehicle weights, axle spacing, vehicle class, travel speed, vehicle length, and traffic volume. These data elements support effective transportation planning, infrastructure design, and policy development. Therefore, it is important that WIM sensors supply accurate data. After initial installation and calibration, WIM systems may experience measurement drifts in weight and axle detection. Recalibration takes two general forms: (a) On-site calibration involving running trucks of known weight over WIM scales and (b) Auto-calibration methods involving comparisons to assumed reference weights. Auto-calibration can be more cost and time effective than …

Evaluation Of Fracture Principles In Asphalt Concrete Utilizing The Sc(B) Geometry, Airam Marlee Morales Vega

Graduate Theses and Dissertations

Since cracking is one of the principal distresses to be considered in asphalt concrete, multiple fracture tests and geometries have been used to quantify cracking resistance. One of the most popular geometries that have been used in fracture tests is the Semi-Circular bend (SC(B)). However, for this geometry, most of the fracture test methods use different parameters such as thickness, testing temperatures, and loading rates. Thus, the purpose of this research was first to evaluate fracture energy by performing a ruggedness test based on ASTM E1169. Then, to apply fracture mechanics concepts to evaluate three specimen thicknesses (25, 50, and …

Bicontinuous Interfacially Jammed Emulsion Gels (Bijels) As Media For Enabling Enzymatic Reactive Separation Of A Highly Water Insoluble Substrate, Sanghak Cha, Hyun Lim, Martin Haase, Kathleen Stebe, Gyoo Jung, Daeyeon Lee

Henry M. Rowan College of Engineering Departmental Research

Although enzymes are efficient catalysts capable of converting various substrates into desired products with high specificity under mild conditions, their effectiveness as catalysts is substantially reduced when substrates are poorly water-soluble. In this study, to expedite the enzymatic conversion of a hydrophobic substrate, we use a bicontinuous interfacially jammed emulsion gel (bijel) which provides large interfacial area between two immiscible liquids: oil and water. Using lipase-catalyzed hydrolysis of tributyrin as a model reaction in a batch mode, we show that bijels can be used as media to enable enzymatic reaction. The bijel system gives a four-fold increase in the initial …

Standardized Waterproof Testing Of Plastic Based Material Flooring (Pbm Flooring), John P. Sanders, Cody Spence

Publications

Tile Council of North America Product Performance Testing Laboratory, under the direction of Dr. John Sanders of the Bishop Materials Laboratory at Clemson University, evaluated the extent that water can leak through plastic based material (PBM)¹ floor coverings advertised as 100% waterproof. To make this assessment, product literature was examined to determine which test methods were used to support the manufacturers’² claims of products being waterproof. Neither test methods or data to justify a 100% waterproof claim were found, despite a thorough review of product literature.³

ASTM, ANSI, ISO, and CEN standards were examined for relevant test …

Wet Slip Resistance Of Plastic Based Material Flooring (Pbm Flooring), John P. Sanders, Grant Davidson

Publications

Tile Council of North America Product Performance Testing Laboratory, under the direction of Dr. John Sanders of the Bishop Materials Laboratory at Clemson University, measured the wet Dynamic Coefficient of Friction (DCOF) of 22 plastic based material (PBM¹) flooring products that manufacturers² advertise or claim to be waterproof, water resistant, or depict being used in areas where flooring gets wet.³ The claims suggest that such PBM products can be used where exposed to water. However, product literature for only five products tested in this report cautioned the products can be potentially slippery when wet, and no …

The Bridge Newsletter Winter 2019, Missouri University Of Science And Technology

The Bridge Newsletter

-Dehghani joins S&T
-Life after death of solar panels
-Civil engineering senior studies in Hong Kong
-Planning for future climate changes in the Artic

Small Ruminant Health Intervention Calendar In Ethiopia, Mesfin Mekonnen, Ayalew Assefa, Tesfalem Nane, Firdawok Ayele, Asrat Arke, Belay Elias, Barbara Wieland

Daugherty Water for Food Global Institute: Faculty Publications

Contents

1 Background................................................................................................... 3
2 Developing the health intervention calendar............................................................ 4
The treatment calendar ......................................................... 4 Applying the calendar..................................................................... 5 4 References................................................................... 8

Kernels And Beyond For Data Similarity Learning In Data Mining, Akshay Malhotra

Electrical Engineering Dissertations - Archive

This work discusses the problem of unsupervised clustering of signals/data vectors based on their information content. A correlation based perspective to the clustering problem has been considered, thus relying on the high correlation between data vectors from the same class rather than on the position of the vectors in the data space. In the past, correlation based clustering has been formulated using a canonical correlation framework or as a matrix factorization problem and has been solved with different variants of gradient descent. This work focuses on improving the clustering performance by modifying the framework to utilize non-linear associations or correlations. …

Identification And Characterization Of Gate Oxide Defects Responsible For Low Frequency Noise In Mosfets, A. S. M. Shamsur Rouf

Electrical Engineering Dissertations - Archive

The main objective of this work is to identify and characterize gate oxide defects that are present in submicron p-channel metal oxide semiconductor field effect transistors (pMOSFETs) and which are responsible for random telegraph signals (RTS). With the downscaling of MOSFETs, alternating capture and emission of channel carriers by defects residing at the oxide-semiconductor interface and bulk oxide have become a pronounced problem. Even though RTS has been used for several years as a tool to characterize the interface/bulk defects, RTS in pMOSFETs has been under-reported compared to that in nMOSFETs, resulting in less information on hole defects in pMOSFETs …

Pulsed Detonation Engine Nozzle Design And Analysis, Rahul Kumar

Mechanical and Aerospace Engineering Dissertations - Archive

For a hypersonic flight mission, different flight regimes have been recognized. The successful and efficient operation of the aircraft to traverse through all the flight regimes requires the integration of various propulsion cycles into a single flow path. Using the phenomenon of detonation initiation and propagation, a multi-mode detonation based propulsion concept was proposed for hypersonic flight. Of the different modes proposed, it was recognized that the efficient operation of Normal Detonation Wave Engine (NDWE) mode and Oblique Detonation Wave Engine (ODWE) mode played an important role as they delivered thrust at critical parts of the trajectory. For this study, …

Improving Compressive Strength Of High Modulus Carbon-Fiber Reinforced Polymeric Composite With Varying Modulus Fibers, Sarvenaz Ghaffari

Mechanical and Aerospace Engineering Dissertations - Archive

There has been a strong demand in using high-modulus (HM) carbon-fiber composites potentially enabling lightweight aircraft structures with significant weight savings. However, extremely low fiber-direction compressive strength has been a well-recognized weakness of the HM composites, preventing their implementation in aircraft platforms. Fiber-direction compressive strength of HM and intermediate-modulus (IM) carbon fiber-reinforced polymers (CFRP’s) is presumably governed by microstructural stability. However, strong decrease in fiber-direction compressive strength of HM carbon-fiber composites, compared to their intermediate modulus (IM) counterparts, contradicts predictions from available microstructural buckling theories. A recent work demonstrated that significant improvement in the fiber-direction compressive strength of HM carbon-fiber …

Numerical Study Of Detonation Flame Arrestor Performance And Detonation Interaction With The Arrestor Element, Hoden Ali Farah

Mechanical and Aerospace Engineering Dissertations - Archive

A numerical study of detonation propagation and interaction with a flame arrestor product in a combustible gas/vapor transport pipeline system is conducted. The flame arrestor element is modeled as a porous medium using the Forchheimer equation, which is incorporated in the governing conservation equations as a momentum sink. The Forchheimer porous medium model is then used to model the flow through a representative four-inch detonation flame arrestor and is validated with experimental data. The detonation propagation simulation is modeled with the Reynolds averaged Navier-Stokes (RANS) equations extended for reacting flow. A 21-step chemical kinetic mechanism with 10 species is used …

Numerical Study Of High–Frequency Fluidic Valve Injectors For Detonation Engine Applications, Sushma Yalavarthi

Mechanical and Aerospace Engineering Dissertations - Archive

The feasibility of fluidic valves for use in detonation-based engines was studied numerically. The fluidic valve acted by shutting off reactant flow through the high pressure behind detonation waves propagating past the valve opening. The valve which featured a plenum cavity was mounted to the side of a pulsed detonation engine, an arrangement that allowed the valve to be characterized under a sustained operation. A series of different cavity lengths were studied. Further, a numerical study of the high-frequency fluidic valve was conducted by using a two-dimensional reactive Euler solver. A 19–step elementary mechanism was employed for the stoichiometric oxyhydrogen …

Dynamics Of A Pulse Detonation Engine Driven Linear Power Generator, Umang Umeshkumar Dighe

Mechanical and Aerospace Engineering Dissertations - Archive

The dynamics of a pulse detonation engine driven linear power generator were studied. For an ideal pulse detonation engine, the thrust generated is in the form of a piecewise function given by the Endo-Fujiwara model. Nonlinear electromagnetic damping is also introduced in the system due to the rare earth permanent magnets present in the linear generator architecture. Various linear generator topologies were studied using static magnetic analysis. Two configurations of a single degree-of-freedom oscillator system, one with a linear spring restoring force and another with geometric nonlinear spring restoring force, were investigated to study any potential advantages of using nonlinear …

Droplet-Based Microextraction Of Dna Enabled By Electrowetting-On-Dielectric Digital Microfluidics, Shubhodeep Paul

Mechanical and Aerospace Engineering Dissertations - Archive

In recent years there have been significant advances in micro/nanotechnologies employing miniaturized platforms to achieve efficient sample pre-processing, separation, and quantification processes. The idea of bringing several lab-scale protocols on to a single chip, i.e., a lab-on-a-chip (LOC) device along with automation, is a reality now. Miniaturization of biochemical operations usually handled in a laboratory has numerous advantages, such as cost effectiveness, multiplexing, assay speed, and sensitivity. Microfluidic technologies used in LOC devices can manipulate tiny volumes of samples and reagents to perform on-chip protocols with minimal human intervention. Electrowetting-on-dielectric (EWOD)-based digital microfluidics (DMF) is one of the LOC platforms …

Assessment Of Material State In Composites Using Global Dielectric State Variable, Vamsee Vadlamundi

Mechanical and Aerospace Engineering Dissertations - Archive

Composites are heterogeneous in nature and a fundamental understanding of the material response to applied mechanical, thermal, electrical and other multi-physical fields is required to efficiently design and synthesize the material system and demands attention to long-term behavior in particular. Unlike metals, composites are designed to develop distributed damage and initiation of a single microscopic crack does not individually affect the strength/life of these materials. Therefore, the primary interest is not in single local events but in the process of interaction of multiple events that have a collective global effect on the material behavior. The interaction of these local events …

Development And Testing Of A Control Strategy For Dynamic Cooling At Rack Level In Data Centers, Amrutha Valli Rachakonda

Mechanical and Aerospace Engineering Theses - Archive

Cooling is a critical part of data center’s infrastructure, and with ongoing demands in data processing and storage, thermal management issues are of great concern. Some imperative methods of removing heat are either using air or liquid (preferably water or refrigerant). When high power density modules are involved, liquid cooling addresses some of the problems faced by air cooling as liquid coolants have higher thermal capacitance. Also, in the case of multi-chip modules, a non-uniform heating due to multi-core generates hot-spots and increases temperature gradients across the module. A dynamic cold plate along with a self-regulated flow control device was …

Assessing The Impact Of Principal Component Analysis On Accurately Predicting Melanoma Diagnosis Applied On Different Classification Models, Juan Cristobal Olmedo Rivera

Industrial, Manufacturing, and Systems Theses - Archive

With huge amounts of data at our disposal in the medical field, mathematical models are built to diagnose diseases. This study focuses on melanoma because it’s the type of skin cancer that accounts for most deaths, up to 7,230 in 2019 according to the American Cancer Society. The study focuses on the effectiveness on diagnosing melanoma and how Principal Component Analysis (PCA) impacts the performance of four models being assessed, which are: K Nearest Neighbor (KNN), Logistic Regression (LR), Support Vector Machines (SVM), and Artificial Neural Networks (ANN). Each model evaluates the melanoma dataset before and after performing the PCA …

Autonomous Carrier Landing Of A Fixed-Wing Uav With Airborne Deck Motion Estimation, Metin Kus

Mechanical and Aerospace Engineering Theses - Archive

This study focuses on the design, implementation, and evaluation of an autonomous carrier landing system featuring an airborne deck motion estimation module. The three-dimensional dynamics of a fixed-wing UAV with the actuator and engine dynamics are considered. A carrier motion model that accounts for the perturbations caused by various sea states is built. An airborne measurement system, which is composed of a calibrated camera and light-emitting beacons, is utilized to detect several coplanar target points on the moving carrier deck. The known correspondence between the locations of the target points and their coordinates on the focal plane of the camera …

Static Response Calibration Of 3d Printed Thin Walled Structures Using Fused Deposition Modelling, Akhilesh Ravindra Kulkarni

Mechanical and Aerospace Engineering Theses - Archive

3-D printing has enabled flexible, tool-less fabrication that yields numerous benefits. One benefit is unique and complex structural arrangements that increase design freedom to minimize weight. Such arrangements can be guided by advanced topology, shape, and sizing optimization tools using appropriate process constraints to ensure a printable design and can include highly integrated structural details such as stiffeners, flanges, frames, and other connections. 3D printing thin wall aircraft structures presents challenges for material and structural characterization. 3D printing enables integrated structural details, each detail is affected by the print process capability to fabricate the local geometry and deviations from designed …

Backstepping Approach For Design Of Cascaded Pid Controller With Guaranteed Trajectory Tracking Performance For Micro-Air Uav, Yusuf Kartal

Mechanical and Aerospace Engineering Theses - Archive

Flight controllers for micro-air UAVs are generally designed using Proportional- Integral-Derivative (PID) methods, where the tuning of gains is difficult and time-consuming, and performance is not guaranteed. In this thesis, we develop a rigorous method based on the sliding mode analysis and nonlinear backstepping to design a PID controller with guaranteed performance. This technique provides the structure and gains for the PID controller, such that a robust and fast response of the UAV for trajectory tracking is achieved. First, the second-order sliding variable errors are used in a rigorous nonlinear backstepping design to obtain guaranteed performance for the nonlinear UAV …

Development Of Medical Devices For Osteoarthritis Diagnosis, Antimicrobial, Wound Closure, And Wound Ph Milieu Monitoring, Shuxin Li

Bioengineering Dissertations - Archive

Nanotechnology has been widely used in the field of biomedical engineering. For example, nanoparticles have been employed for targeted drug delivery due to their retention effect, increased permeability, site-specific targeting, and avoiding phagocytosis as foreign materials. Moreover, nanotools, such as liposomes, Q-dots, dendrimers, micelles, and carbon nanotubes, have been developed for disease diagnosis and treatment. Generally, the application of nanotechnology can be categorized as follows: nanomedicine, tissue regeneration, biomarker/biosensors, nanorobots, and gene therapy. In the past four years, I have been focusing on developing nanotechnology for diagnosis and treatment of many diseases such as osteoarthritis, open wound, and infection. Based …

Impacts Of Construction Material Delay In Iraq, Omar Raad Abdullah

Civil Engineering Theses - Archive

The construction industry is considered one of the most important industries in Iraq. It is well known that most construction projects in this country can experience missed deadlines and cost overruns or both. The main objectives of this study are to evaluate the impact of construction material shortages and to determine the most important problems causing these shortages in Iraq. Above objectives are achieved through a literature review and a survey, which include a questionnaire used to assess the perceptions of the main participants involved in the construction of different types of projects, such as infrastructure, residential, highways and medical …