Engineering Commons^™

Aasho Road Test Tandem Axleload Data Adapted To Fundamental Concepts, Herbert F. Southgate, Robert C. Deen, James H. Havens

Kentucky Transportation Center Research Report

The reptitions of tandem axleloads applied to the AASHO Road Test were analyzed by the same method previously reported in analyzing the corresponding single axleload data. The essential findings were: 1. One repetition of a 34-kip (151-kN) tandem axleload appears to cause the same damage as one repetition of an 18-kip (80-kN) single axleload. 2. The relationship of log repetitions versus axleload used by Kentucky appear to be equally valid for single and tandem axleloads. 3. The use of superposition principles, and equivalency of repetitions, in combination with terminal serviceability indiced permitted analyses of the tandem axleload data and comparison …

Sio2-Si Film-Substrate Reflection Polarizers For Different Mercury Spectral Lines, A.-R. M. Zaghloul, R. M.A. Azzam

Electrical Engineering Faculty Publications

No abstract provided.

Production Methods Of Wood Fiber Particleboard, Bruce Novak

Graduate Research Papers

The purpose of this study will be to investigate the development, production and use of particleboard, for the purpose of incorporating a unit in particleboard production, on a limited scale, into an industrial arts program.

Solar Fluid Heater With Electromagnetic Radiation Trap, Blaine Frank Parker

Biosystems and Agricultural Engineering Faculty Patents

A solar fluid heater including a radiation trap for concentrating solar radiation which has been focused on or near a line at the center of a transparent pipe assembly containing the fluid to be heated is described. The pipe assembly may include one or more transparent pipes containing one or more sets of reflective fins which are disposed in direct heat exchanging contact with the fluid to be heated. The focused radiation entering the pipe assembly experiences multiple reflections off one set of reflective fins therein, thus concentrating the solar radiation. The reflective fins are made absorptive near the apex …

Effectiveness Of Green-Extension Systems At High-Speed Intersections, Charles V. Zegeer

Kentucky Transportation Center Research Report

The purpose of this study was to determine the effectiveness of green-extension systems (GES) for reducing the dilemma-zone problem associated with the amber phase of traffic signals at high-speed intersections. Reactions of 2,100 drivers were noted during the amber phase at nine intersections, and the dilemma-zone distances with respect to the stop bar were determined.

Before-and-after studies made at three green-extension sites showed a 54-percent reduction in total accidents and a 75-percent reduction in rear-end accidents after GES installation. Accident severity was unaffected.

Conflict, volume, delay, and speed data were taken before and after GES installation at two sites. A …

Traffic Accidents: Day Vs. Night, Donald R. Herd, Kenneth R. Agent, Rolands L. Rizenbergs

Kentucky Transportation Center Research Report

A comparison of accidents during daylight and darkness was made for both rural and urban roads. Accident rates on all types of rural roads were higher during darkness than during daylight. Critical accident rates during darkness for various types of roads were calculated. In urban areas, a larger percentage of accidents occurred on wet pavements during darkness than during daylight, but there were no significant differences for rural roads. No significant difference was found between average speeds during conditions of daylight and darkness. On rural roads, imposition of the 55-mph (24.6-m/s) speed limit resulted in a reduction in accident rates …

The Rotary Engine: Principles And Operations, Del Simpson

Graduate Research Papers

This study will be concerned with tracing the development of the rotary engine and to help prepare a unit for a high school industrial arts class.

It is the purpose of this study to: 1) review available literature on rotary engines, 2) write to manufacturers of various rotary engines seeking technical and educational information, 3) determine feasibility of new developments, 4) present information orally to the class and a written paper to the Department of Industrial Technology.

Atomic Simulation Of The Al2 (111) (110) Edge Dislocation In Alpha-Iron, Brent L. Adams, P. C. Gehlen, J. P. Hirth, R. G. Hoagland

Faculty Publications

The authors are pleased to acknowledge: the support of this research by the National Science Foundation under Grant DMR 74-21243 and by the provision of computer time by The Ohio State University and by Battelle Columbus Laboratories; and helpful comments on the manuscript by V Vitek. Computer simulation is used to obtain the plane strain and non-plane strain equilibrium core structures for the a/2 <111> {110} edge dislocation in alpha-iron as modelled by the Johnson potential. The methods of the integral formulation of anisotropic linear eleasticity theory are employed in the analysis. Flexible core boundary methods reveal that positive volume expansions …

Cpacs Happenings (April 1977 Newsletter), College Of Public Affairs And Community Service, University Of Nebraska At Omaha

CPACS Newsletters

The College of Public Affairs and Community Service (CPACS) newsletter that reported on the news, collaborations, events, and general happenings of the UNO College of Public Affairs and Community Service. This newsletter has had many names and variations over the years including SPACS Newsletter (1973); Newsletter of the College of Public Affairs and Community Service (1973-1974): Happenings (1974-1980s); and the current e-newsletter titled the CPACS Collective (2021-)

Ua64/3 Readout, Wku Industrial Education & Technology

WKU Administration Documents

Newsletter includes articles:

• Renovation of Industrial Education Building Nearing Completion
• Tomazic, Norman. Basic Industrial Education: Futures Oriented "Sabre-toothed" Curriculum?
• Conley, Franklin. Comments re: departmental news
• New Electricity / Electronics Facilities
• WKU Student Receives KIEA Scholarship, Bonnie Thomerson
• Zax, Carol. Communication & Interaction
• Pittman, Frank. Guitars, Guitars, Guitars re: Hascal Haile
• IE&T One-Liners
• Walter Nalbach Scholarship Fund

Acuta Enews April 1977, Vol. 6, No. 4

ACUTA Newsletters

In This Issue

PRESIDENT'S MESSAGE

EDITORIAL

COMMUNCATIONS CONSULTANTS

FEATURED INSTITUTION

ANNUAL REPORT

BOARD OF DIRECTOR'S MEETING

NEW MEMBERS

1978 CONFERENCE DATES

MAJOR TELECOMMUNICATIONS CONFERENCE

PROPOSED BUDGET 1977-78

Some Uncertainties Of Slope Stability Analyses, Robert C. Deen, Tommy C. Hopkins, David L. Allen

Kentucky Transportation Center Research Report

Some practical limitations of total stress and effective stress analyses are discussed. For clays having a liquidity index of 0.36 or greater, φ-equal-zero analyses based on laboratory undrained shear strengths give factors of safety close to the actual factor of safety. However, based on field vane strengths, φ-equal-zero analyses may yield factors of safety which may be too high. The difference between field vane and calculated shear strengths increased as the plasticity index increased. For clays having a liquidity index less than 0.36, φ-equal-zero analyses using laboratory undrained shear strengths give factors of safety that are much too high; but …

Acoustic Emission Testing Of High-Strength Steel Weldments, Theodore Hopwood Ii

Kentucky Transportation Center Research Report

Manual arc welds were made on high-strength ASTM A 514 and A 588 steels. Different weldment configurations were employed in order to vary the restraint on the welds during cooling. The weldments were monitored 'in-cooling' with acoustic emission equipment. Weldments having greater restraint produced more acoustic emission, usually for longer periods of time. Weldments which fractured during cooling produced more acoustic emission than those which were unflawed.

Suspended And Dissolved Solids Effects On Freshwater Biota: A Review, Darwin L. Sorensen, Margaret M. Mccarthy, E. Joe Middlebrooks, Donald B. Porcella

Reports

It is widely recognized that suspended and dissolved solids in lakes, rivers, streams, and reservoirs affect water quality. In this report the research needs appropriate to setting freshwater quality criteria or standards for suspeneded solids (not including bedload) and dissolveed solids are defined by determining the state of our knowledge from a critical review of the recent literature in this field. Common literature sources and computer searching routines were used as an initial source of information followed by detailed journal searches. Although some 185 journal articles, government reports, and other referecnes were cited herein (about 45 percent publicshed since 1974) …

Single Particle Scattering With Focused Laser Beams, Lee W. Casperson, Cavour W. Yeh

Electrical and Computer Engineering Faculty Publications and Presentations

A scattering technique is described in which the incident laser beam is tightly focused to isolate the effects of a single particle. In this way the individual particles may be studied in their natural environment, and experiments with latex spheres are in agreement with the theory.

Computerized Analysis Of Stress-Strain Consolidation Data, E. Gregory Mcnulty

Kentucky Transportation Center Research Report

A computerized, mathematical algorithm is described and presented for analyzing the semilogarithmic stress-strain (time-independent) properties of standard, controlled-gradient, and controlled-rate-of-strain consolidation tests. This algorithm is an automation of manual graphical procedures currently used in engineering practice to obtain stress-strain information necessary for use in time-independent settlement analysis. The Casagrande and Schmertmann constructions are analytically represented to determine the preconsolidation stress and the in situ, compressibility coefficients of compression and expansion. Values for each of these parameters range between a probable and minimum value. The point of maximum curvature is determined for the Casagrande construction by use of the mathematical definition …

Laser Doppler Anemometry For Flow Measurement, William W. Durgin, Lawrence C. Neale

Office of the Provost Scholarship

Laser doppler anemometers are non-invasive, linear, and inherently precise. Calibration, in the usual sense, is not necessary; length and frequency measurements suffice to establish velocity at a spatial point. Measurements were made at points in the cross-sections of two square ducts containing water flow. The points were selected in conformance with a numerical integration scheme to be used for volumetric flow rate determination from the velocity measurements. The experiments were performed in a primary calibration facility at flows up to 1.25 m³/sec using ducts with sides 46 and 92 cm. The anemometer, operating in forward scatter differential mode …

Sio2-Si Film-Substrate Single-Reflection Retarders For Different Mercury Spectral Lines, A.R.M. Zaghloul, R.M.A Azzam

Department of Electrical and Computer Engineering: Faculty Publications

Design parameters for SiO₂- Si film-substrate single reflection retarders for several mercury spectral lines are presented. An example of an angle-of-incidence tunable retarder (AITR) capable of multiple wavelength operation (MWO) is reported Simple, approximate formulae for calculating film-substrate retarder design parameters (least film thickness d' and incidence angle) are presented.

Identification Of Hazardous Locations On City Streets, Charles V. Zegeer, Robert C. Deen

Kentucky Transportation Center Research Report

The purpose of this study was to develop an effective method for identifying hazardous locations in Kentucky cities (over 2,500 population). Methods used in 45 other states were reviewed. Accident information for 69 of the 97 cities over 2,500 population was used to develop criteria for an identification method.

A Number Method was selected for initial identification of midblocks and intersections on arterial-collector streets and on urban freeways. A Rate-Quality Control Method was included in the form of a critical rate factor computed for each location. A set of critical rate curves was constructed for easy determination of hazardous locations. …

Positron Lifetime As A Function Of Grain Size, Hollis P. Leighly

Materials Science and Engineering Faculty Research & Creative Works

Published data on positron annihilation lifetime in copper as a function of grain size have been analyzed to show that there is a linear relationship between the internal grain boundary surface area, per unit volume, S v, and the positron lifetime, τ. The analysis indicates that grain boundaries are important in the trapping of positrons. It is suggested that the slope of the resulting straight line, dS v/dτ, can be used to determine the annihilation rate of the grain boundaries. © 1977 Springer-Verlag.

Voidless And Internally Sealed Concretes (Construction Report; Silas Creek Bridge, Us 27, Mp-009-0027-B0002), Assaf S. Rahal

Kentucky Transportation Center Research Report

Laboratory investigations on concretes containing super water reducers, PVP and Melment, indicated their suitability for field utilization. Wax beads have been used by other states in concretes for bridge slabs. This report describes the reconstruction of a four-span bridge having three experimental slabs and one conventional slab. Post-construction analyses of cores are included.

Estimating Hourly Solar Radiation For One-Axis Tracking Focusing Collectors, Carl E. Bingham, David M. Posner, Jerry O. Bradley

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

Performance simulations of focusing parabolic collectors are hampered by a limited amount of useful insolation data. Hourly values of total radiation on a horizontal surface are the most common data available from the National Oceanographic & Atmospheric Administration. This paper develops a method to convert this total horizontal radiation to direct radiation on the surface of the tracking collector.

Energy Conservation In Ammonia Production, Yash P. Gupta, Donald B. Wilson

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

The Federal Energy Administration currently is considering energy conservation goals for the industry. This paper presents methods for chemical/petroleum industry to conserve energy. Ammonia Production is used as an example.

Plutonium Assessment Modeling -- Government Policy, Non-Proliferation, And The Government Fence, Harold A. Kurstedt Jr., Joel A. Nachlas

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

Assessment modeling for the evaluation of plutonium as an energy resource is stressed, and generic mathematical model forms are outlined. Representative necessary objective functions are developed. Constraints and assumptions are listed. An example involving present-day light water reactor technology is demonstrated. Technical, environmental, and political implications are drawn. Specific new directions for analysis are suggested. The position of the boundary of government control and responsibility -- the government exclusion fence -- is shown to be a critical, but overlooked, constraint. Existing governmental uranium stockpiles may be an unmentioned, though important, constraint.

The Impact Of Regulation Upon The Oil And Gas Industries, Lee Carter

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

It is paradoxical that the oil and gas industries both ask for and resist the idea of regulation. Historic examples are given of how and why this is so. Since the Arab oil crisis of 1973, new and onerous rules for domestic producers have been introduced, first by improvization and more recently by a national energy plan. Both the good and bad features of the 1977 national energy plan are reviewed to generate words of commendation and words of warning about its effect on the oil and gas industries.

Agricultural Crop Drying And Space Heating Using A Solar Energy Intensifier, M. A. Hellickson, W. H. Peterson, S. E. Saienga, J. L. Julson

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

A solar energy-intensifier-thermal energy storage system was developed and tested under actual climatic conditions in South Dakota. Performance characteristics of the system are presented for its use in drying shelled corn and for agricultural space heating. Comparisons between solar and conventional drying between solar supplemented and conventional heating are reported.

Programming Language Requirements For Human Communication Structures Or Computer Conferencing, Computerized Conferencing & Communications Center, Peter Gordon Anderson

Computerized Conferencing and Communications Center Reports

Our overall goal is to be able, simply and quickly, to construct computer conferencing systems for new requirements, applications, and even experimental ideas or fantasies. One way to view this requirement is as the creation of a highly parameterized conferencing system itself. Our view, however, is that of a programming language; i.e., an integrated notational system for the specification of communication structures and the associated actions or computation to be taken by the computer system hosting the structure.

A communication structure consists of a group of people (and storage devices) each endowed with some characteristics, and some means of person-to-person …

Test 1236: Steiger Panther Iii St-325 Diesel 10-Speed, Also Steiger Panther Iv Cm-325 Diesel 20-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1242: Ford 7700 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Steel Roof Deck Design Manual, Steel Deck Institute

Steel Deck Institute (SDI) Specifications and Manuals (1939 - present)

No abstract provided.