Engineering Commons^™

Garbage Float, Gabor Papp, Max Woolverton, Scott Ulatowski, Daniel Ross, Nicholas Gayle, Bryan Merchan-Aragon, Noah Yco, Nicholas Fawcett, Jared Wright, Abdulaziz Salman G Alshahrani, Andrew Mcquire

Mechanical and Civil Engineering Student Publications

Trash pileup in our waters is an increasing problem. Removing floating plastics and debris from our ecosystem would reduce mortality rate of marine animals. Solutions for this already exist but most of them are proprietary and expensive. Therefore, an autonomous, publicly available and cheap alternative was developed to skim and clean the water surface from garbage.

Education And Training Networks, Ken Thomas, Joe Harrington, Robin Stubbs, Sean Carroll, Emily Shakespeare, Rahat Ullah, Adhban Farea, Theresa-Marie Greiwe

Tools

Education And Training Networks Inventory is a review of relevant network in Ireland and the EU.

2024 (Spring) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the spring of 2024.

Inertial Particle Clustering Due To Turbulence In An Air Jet, Bianca Viggiano, Kris Gish, Stephen Solovitz, Raul Bayoan Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Explosive volcanic eruptions create turbulent plumes of fine ash particles. When these particles collide in the presence of moisture and electrostatic fields they combine into larger aggregates, which can significantly change the atmospheric residence time of the airborne cloud. Previous studies have suggested that turbulence may lead to preferential concentration—also known as clustering—of particles within the flow, increasing the likelihood of collisions and aggregation. Few experimental studies have quantified these processes for volcanic plumes. This behavior was investigated using a particle-laden air jet. By systematically varying the exit speed and the size, density, and concentration of particles, flows were produced …

Convolutional Spiking Neural Networks For Intent Detection Based On Anticipatory Brain Potentials Using Electroencephalogram, Nathan Lutes, V. Sriram Siddhardh Nadendla, K. Krishnamurthy

Computer Science Faculty Research & Creative Works

Spiking neural networks (SNNs) are receiving increased attention because they mimic synaptic connections in biological systems and produce spike trains, which can be approximated by binary values for computational efficiency. Recently, the addition of convolutional layers to combine the feature extraction power of convolutional networks with the computational efficiency of SNNs has been introduced. This paper studies the feasibility of using a convolutional spiking neural network (CSNN) to detect anticipatory slow cortical potentials (SCPs) related to braking intention in human participants using an electroencephalogram (EEG). Data was collected during an experiment wherein participants operated a remote-controlled vehicle on a testbed …

Experimental, Computational, And Machine Learning Methods For Prediction Of Residual Stresses In Laser Additive Manufacturing: A Critical Review, Sung Heng Wu, Usman Tariq, Ranjit Joy, Todd Sparks, Aaron Flood, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In recent decades, laser additive manufacturing has seen rapid development and has been applied to various fields, including the aerospace, automotive, and biomedical industries. However, the residual stresses that form during the manufacturing process can lead to defects in the printed parts, such as distortion and cracking. Therefore, accurately predicting residual stresses is crucial for preventing part failure and ensuring product quality. This critical review covers the fundamental aspects and formation mechanisms of residual stresses. It also extensively discusses the prediction of residual stresses utilizing experimental, computational, and machine learning methods. Finally, the review addresses the challenges and future directions …

Insight Into Uniform Filming Of Lif-Rich Interphase Via Synergistic Adsorption For High-Performance Lithium Metal Anode, Yufang He, Li Wang, Aiping Wang, Bo Zhang, Hiep Pham, Jonghyun Park, Xiangming He

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Multi-scale simulation is an important basis for constructing digital batteries to improve battery design and application. Lif-rich solid electrolyte interphase (sei) is experimentally proven to be crucial for the electrochemical performance of lithium metal batteries. However, the lif-rich sei is sensitive to various electrolyte formulas and the fundamental mechanism is still unclear. Herein, the structure and formation mechanism of lif-rich sei in different electrolyte formulas have been reviewed. On this basis, it further discussed the possible filming mechanism of lif-rich sei determined by the initial adsorption of the electrolyte-derived species on the lithium metal anode (lma). It proposed that individual …

Underwater Double Vortex Generation Using 3d Printed Acoustic Lens And Field Multiplexing, Chadi Ellouzi, Ali Zabihi, Farhood Aghdasi, Aidan Kayes, Milton Rivera, Jiaxin Zhong, Amir Miri, Chen Shen

Henry M. Rowan College of Engineering Faculty Scholarship

The generation of acoustic vortex beams has attracted an increasing amount of research attention in recent years, offering a range of functions, including acoustic communication, particle manipulation, and biomedical ultrasound. However, incorporating more vortices and broadening the capacity of these beams and associated devices in three dimensions pose challenges. Traditional methods often necessitate complex transducer arrays and are constrained by conditions such as system complexity and the medium in which they operate. In this paper, a 3D printed acoustic lens capable of generating a double vortex pattern with an optional focusing profile in water was demonstrated. The performance of the …

Impact Of Welding Parameters In The Porosity Of A Dissimilar Welded Lap Joint Of Cp800-Xpf1000 Steel Weldment By Gmaw-P, Julio Cesar Garcia-Guerrero, Francisco Fernando Curiel-López, Víctor Hugo López-Morelos, Jaime Taha-Tijerina, Teresita Jesus Sánchez-Cruz, Maria Del Carmen Ramirez-Lopez, Eduardo Cortes-Carillo, Miguel Angel Quinones-Salinas

Informatics and Engineering Systems Faculty Publications and Presentations

The use of the orthogonal array L4 allows a determination of the effect between the welding parameters peak current (Ip), background current (Ib) and frequency (f) on the porosities in a dissimilar welded lap joint of CP800 and XPF1000 steel weldment by the gas metal arc welding process with the transfer pulsed mode. According to the results, modifications in the welding parameters affect the heat input during welding. A heat input higher than 0.30 KJ/mm generates up to 0.32% porosity in the weld metal, while a heat input lower than 0.25 KJ/mm generates up to 28% porosity in the weld …

Machine Learning A Universal Harmonic Interatomic Potential For Predicting Phonons In Crystalline Solids, Huiju Lee, Yi Xia

Mechanical and Materials Engineering Faculty Publications and Presentations

Phonons, as quantized vibrational modes in crystalline materials, play a crucial role in determining a wide range of physical properties, such as thermal and electrical conductivity, making their study a cornerstone in materials science. In this study, we present a simple yet effective strategy for deep learning harmonic phonons in crystalline solids by leveraging existing phonon databases and state-of-the-art machine learning techniques. The key of our method lies in transforming existing phonon datasets, primarily represented in interatomic force constants, into a force-displacement representation suitable for training machine learning universal interatomic potentials. By applying our approach to one of the largest …

Increasing The Dissolution Rate Of Polystyrene Waste In Solvent-Based Recycling, Rita Kol, Ruben Denolf, Gwendoline Bernaert, Dave Manhaeghe, Ezra Bar Ziv, George W. Huber, Norbert Niessner, Michiel Verswyvel, Angeliki Lemonidou, Dimitris S. Achilias, Steven De Meester

Michigan Tech Publications, Part 2

Solvent-based recycling of plastic waste is a promising approach for cleaning polymer chains without breaking them. However, the time required to actually dissolve the polymer in a lab environment can take hours. Different factors play a role in polymer dissolution, including temperature, turbulence, and solvent properties. This work provides insights into bottlenecks and opportunities to increase the dissolution rate of polystyrene in solvents. The paper starts with a broad solvent screening in which the dissolution times are compared. Based on the experimental results, a multiple regression model is constructed, which shows that within several solvent properties, the viscosity of the …

Experimental Investigation Of Long-Term Performance Of Fiber-Reinforced Epoxy And Polyurethane Polymer Composites, Abdel Hamid I. Mourad, Amir Hussain Idrisi, Asima Zahoor, Muhammad M. Sherif, Beckry M. Abdel-Magid

Michigan Tech Publications, Part 2

The primary challenge encountered by polymers and their composites when exposed to saline water is their inadequate ability to withstand wear and tear over time. With a potential to replace conventional materials the long-term performance of FRP composites is still a novice area. This manuscript thus, reports an experimental investigation and prediction of the durability of fiber-reinforced polymer composites exposed to seawater at different temperatures. E-glass/epoxy and E-glass/polyurethane samples were exposed to 23 °C, 45 °C and 65 °C seawater for up to 2700 days (90 months). Tensile tests evaluated the mechanical performance of the composite as a function of …

Wavelength-Induced Shedding Frequency Modulation Of Seal Whisker Inspired Cylinders, Trevor Dunt, Kirby S. Heck, Kathleen Lyons, Christin Murphy, Raul Bayoan Cal, Jennifer A. Franck

Mechanical and Materials Engineering Faculty Publications and Presentations

The spanwise undulated cylinder geometry inspired by seal whiskers has been shown to alter shedding frequency and reduce fluid forces significantly compared to smooth cylindrical geometry. Undulation wavelength is systematically investigated in order to explore its effect on unsteady lift force and shedding frequency. Prior research has parameterized the whisker-inspired geometry and demonstrated the relevance of geometric variations on force reduction properties. Among the geometric parameters, undulation wavelength was identified as a significant contributor to forcing changes. To analyze the effect of undulation wavelength, a thorough investigation isolating changes in wavelength is performed to expand upon previous research that parameterized …

Characterization Of Microstructural And Mechanical Properties Of 17-4 Ph Stainless Steel By Cold Rolled And Machining Vs. Dmls Additive Manufacturing, Pablo Moreno-Garibaldi, Melvyn Alvarez-Vera, Juan Alfonso Beltrán-Fernández, Rafael Carrera-Espinoza, Héctor Manuel Hdz-García, J. C. Díaz-Guillen, Rita Muñoz-Arroyo, Javier A. Ortega, Paul Molenda

Mechanical Engineering Faculty Publications and Presentations

The 17-4 PH stainless steel is widely used in the aerospace, petrochemical, chemical, food, and general metallurgical industries. The present study was conducted to analyze the mechanical properties of two types of 17-4 PH stainless steel—commercial cold-rolled and direct metal laser sintering (DMLS) manufactured. This study employed linear and nonlinear tensile FEM simulations, combined with various materials characterization techniques such as tensile testing and nanoindentation. Moreover, microstructural analysis was performed using metallographic techniques, optical microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The results on the microstructure for 17-4 PH DMLS stainless steel reveal …

Jet-Driven Mixing Regimes Identified In The Unsteady Isothermal Filling Of Rectangular Municipal Water Storage Tanks, Pramod Narayan Bangalore, K. (Kelly) O. Homan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Poor mixing of old and new water in municipal water storage vessels is a well-documented basis for potentially harmful water quality degradation in drinking water distribution systems. This numerical study investigates the effects of inflow and operational variables on mixing in the jet-driven filling process, with a particular focus on the transition from inadequate to sufficient mixing levels. An isothermal unsteady reynolds-averaged-navier-stokes volume-of-fluid (RANS-VOF) simulation is used to model the variable-volume filling process, accounting for the moving free surface following a draw-down in the stored water volume. A low diffusivity tracer is used to mark the old-water volume, and a …

Heat Treatments For Minimization Of Residual Stresses And Maximization Of Tensile Strengths Of Scalmalloy® Processed Via Directed Energy Deposition, Rachel Boillat-Newport, Sriram Praneeth Isanaka, Jonathan Kelley, Frank Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Scalmalloy® is an Al-Mg-Sc-Zr-Based Alloy Specifically Developed for Additive Manufacturing (AM). This Alloy is Designed for Use with a Direct Aging Treatment, as Recommended by the Manufacturer, Rather Than with a Multistep Treatment, as Often Seen in Conventional Manufacturing. Most Work with Scalmalloy® is Conducted using Powder Bed Rather Than Powder-Fed Processes. This Investigation Seeks to Fill This Knowledge Gap and Expand Beyond Single-Step Aging to Promote an overall Balanced AM-Fabricated Component. for This Study, Directed Energy Deposition (DED)-Fabricated Scalmalloy® Components Were Subjected to Low-Temperature Treatments to Minimize Residual Stresses Inherent in the Material Due to the Layer-By-Layer Build Process. …

Wire Texture C-Axis Distribution Of Strontium Ferrite/Pa-12 Extruded Filament, Gabriela Espinosa-Rodriguez, Oluwasola Arigbabowo, Jonathan Alvarado, Jitendra Tate, Wilhelmus J. Geerts

Mechanical Engineering Faculty Publications and Presentations

The magnetic anisotropy of strontium ferrite (SF)/PA12 filament, a popular hard magnetic ferrimagnetic composites that is used for 3D-printing of permanent magnets, is studied by vibrating sample magnetometry. The studied filaments have a composition of SF/PA-12 thermoplastic composite with a 40% wt.  ratio of SF. SF particles are non-spherical platelets with an average diameter of 1.3 um and a diameter to thickness ratio of 3. Filaments are produced by a twin-screw extruder and have a diameter of 1.5 mm. SEM images show that the SF particles are homogeneously distributed through the filament. VSM measurements on different parts of the filaments …

Residual Stress Generation In Additive Manufacturing Of Complex Lattice Geometries, Katie Bruggeman, Nathan Klingbeil, Anthony N. Palazotto

Faculty Publications

Residual stresses developed during additive manufacturing (AM) can influence the mechanical performance of structural components in their intended applications. In this study, thermomechanical residual stress simulations of the laser powder bed fusion (LPBF) process are conducted for both simplified (plate and cube-shaped) geometries as well as five complex lattice geometries fabricated with Inconel 718. These simulations are conducted with the commercial software package Simufact Additive©, which uses a nonlinear finite element analysis and layer-by-layer averaging approach in determining residual stresses. To verify the efficacy of the Simufact Additive© simulations, numerical results for the plate and cube-shape geometries are analyzed for …

Tribological Properties Of H-Bn, Ag And Mgo Nanostructures As Lubricant Additives In Vegetable Oils, Victoria Granja, Kollol Sarker Jogesh, Jaime Taha-Tijerina, C. Fred Higgs Iii

Informatics and Engineering Systems Faculty Publications and Presentations

There exists an ever-growing need for sustainable engineering solutions to improve emission control and the energy efficiency of tribosystems. This study examines the tribological properties of two environmentally friendly vegetable fluids, soybean and sunflower oil, with the addition of three non-toxic nanostructures (h-BN, silver and MgO) at different concentrations. It was found that nanostructures added to vegetable oils at specific concentrations can exhibit good friction reduction and wear preventive properties. The addition of h-BN nanosheets in sunflower oil decreased the coefficient of friction and the wear damage, as measured by the wear scar diameter. Silver and magnesium oxide nanoparticles further …

Simulation Of The Multi-Wake Evolution Of Two Sandia National Labs/National Rotor Testbed Turbines Operating In A Tandem Layout, Apurva Baruah, Fernando L. Ponta, Alayna Farrell

Michigan Tech Publications, Part 2

The future of wind power systems deployment is in the form of wind farms comprised of scores of such large turbines, most likely at offshore locations. Individual turbines have grown in span from a few tens of meters to today’s large turbines with rotor diameters that dwarf even the largest commercial aircraft. These massive dynamical systems present unique challenges at scales unparalleled in prior applications of wind science research. Fundamental to this effort is the understanding of the wind turbine wake and its evolution. Furthermore, the optimization of the entire wind farm depends on the evolution of the wakes of …

Assessing The Lubrication Performance Of Sunflower Oil Modified With Montmorillonite Clay (Mmt) Nanoparticles For Industrial Applications, Md Mashfiqur Rahman, Md Abu Sayeed Biswas, Laura Peña-Pará, Demófilo Maldonado- Cortés, Javier A. Ortega

Mechanical Engineering Faculty Publications and Presentations

Because of the environmental impact and price volatility, there has been a growing concern about using petroleum-based lubricants. This issue has encouraged research into the development of biodegradable lubricants like vegetable oils. This study assessed the tribological behavior of sunflower oil modified with Montmorillonite nanoclay (MMT) as lubricant additives. A block-on-ring tribometer was used to assess the wear and friction characteristics of the nano-lubricants. A custom-made tapping torque tester was used to evaluate the nano-lubricants in a real-world application. It was found that the volumetric wear, Coefficient of Friction, and torque of the system decreased when MMT nanoparticles were added. …

Graphene Reinforced Pvdf Nanofibers Fabricated With The Forcespinning® Method For Water Desalination Applications, Elmmer A. Vera Alvarado, Md. Abdur Rahman Bin Abdus Salam, Ali Ashraf, Karen Lozano

Mechanical Engineering Faculty Publications and Presentations

Direct contact membrane distillation (DCMD) is a thermally driven energy and cost-efficient desalination technique where low-grade energy from solar or waste heat from plants can be used to recover fresh water from high saline water. The DCMD technique allows both the feed and permeate solutions to be in contact with the membrane, where vapor from the feed gets condensed in the permeate side once it collides with low- temperature water. Polyvinylidene fluoride (PVDF) nanofiber membranes were prepared by the ForceSpinning® method, these were later dip coated in graphene solutions prepared with different solvents. The ForceSpinning® method, unlike electrospinning, operates in …

Modelling Of A Drone To Analyze Dynamic Instabilities With Its Delivery System, Eleazar Marquez, Ivan Luna

Mechanical Engineering Faculty Publications and Presentations

In the study herein, an alternative mathematical model was developed with the intention of understanding the dynamics associated with the instabilities generated by an UAV and its delivery system, particularly the coupled nonlinearities of the system, and thus provide feedback to optimize drone design. In this regard, a Newton-Euler methodology was adopted to establish the parameters of the equations of motion of the target UAV system, which consisted of a combination of a platform and delivery system operating simultaneously. Specifically, the UAV platform was modelled as a rigid body which accounted for a total of six-degrees-of-freedom, three corresponding to the …

In-Situ Shear Exfoliation Of Graphene From Graphite Polymer Nanocomposites For Lung And Heart Motion, Md Ashiqur Rahman, Md Abdur Rahman Bin Abdus Salam, Ali Ashraf

Mechanical Engineering Faculty Publications and Presentations

Graphene-based nanocomposites have become attractive for different applications such as energy storage, sensors, biomolecule detection, biomedical, healthcare, and wearable devices due to their unique mechanical, electrical, and thermal properties. However, using commercial graphene for making nanocomposite devices can be expensive, and fabricating nanocomposites can be challenging due to impurities while transferring graphene to elastomer composites. In this study, we used a simple, inexpensive in-situ shear exfoliation method to produce graphene from graphite directly within the elastomer. As the graphene in the elastomer reached beyond its percolation or threshold, electrons hop or tunnel around from one graphene flake to another. So, …

Effect Of Foot Additional Mass On The Clinical Angles Of Knee Extension Exercise, Dumitru I. Caruntu, Alfirio Trejo, Eric Rodriguez, Camila T. Alvarez B

Mechanical Engineering Faculty Publications and Presentations

This study investigates the effect of foot additional mass on the abduction and internal rotation knee angles during knee extension exercise. Three subjects (two male and one female) performed four sets of ten repetitions of the knee extension exercise for the right leg. For the first set, the subject performed the exercise with no additional weight. For each set after, weight was added around the subject’s right foot and the subject was allowed a rest period before beginning the next set. The weights for sets 1, 2, 3, and 4 were 0.00kg (no additional weight) ,0.82kg, 1.64kg, and 2.27kg respectively. …

Left Ventricle Function And Post-Transcriptional Events With Exercise Training In Pigs, Stephanie L. Samani, Shayne C. Barlow, Lisa A. Freeburg, Traci L. Jones, Marlee Poole, Mark A. Sarzynski, Michael R. Zile, Tarek Shazly, Francis G. Spinale

Faculty Publications

Background

Standardized exercise protocols have been shown to improve overall cardiovascular fitness, but direct effects on left ventricular (LV) function, particularly diastolic function and relation to post-transcriptional molecular pathways (microRNAs (miRs)) are poorly understood. This project tested the central hypothesis that adaptive LV remodeling resulting from a large animal exercise training protocol, would be directly associated with specific miRs responsible for regulating pathways relevant to LV myocardial stiffness and geometry.

Methods and results

Pigs (n = 9; 25 Kg) underwent a 4 week exercise training protocol (10 degrees elevation, 2.5 mph, 10 min, 5 days/week) whereby LV chamber stiffness (KC) …

Effects Of Laser Defocusing On Bead Geometry In Coaxial Titanium Wire-Based Laser Metal Deposition, Remy Mathenia, Aaron Flood, Braden Mclain, Todd Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Coaxial wire-based laser metal deposition is a versatile and efficient additive process that can achieve a high deposition rate in the manufacturing of complex structures. In this paper, a three-beam coaxial wire system is studied, with particular attention to the effects of deposition height and laser defocusing on the resulting bead geometry. As the deposition standoff distance changes, so does the workpiece illumination proportion, which describes the ratio of energy going directly into the feedstock wire and into the substrate. Single titanium beads are deposited at varying defocus levels and deposition rates and the bead aspect ratio is measured and …

Low Shear In Short-Term Impacts Endothelial Cell Traction And Alignment In Long-Term, Mohanish Chandurkar, Nikhil Mittal, Shaina P. Royer-Weeden, Steven D. Lehmann, Yeonwoo Rho, Sangyoon J. Han

Michigan Tech Publications, Part 2

Within the vascular system, endothelial cells (ECs) are exposed to fluid shear stress (FSS), a mechanical force exerted by blood flow that is critical for regulating cellular tension and maintaining vascular homeostasis. The way ECs react to FSS varies significantly; while high, laminar FSS supports vasodilation and suppresses inflammation, low or disturbed FSS can lead to endothelial dysfunction and increase the risk of cardiovascular diseases. Yet, the adaptation of ECs to dynamically varying FSS remains poorly understood. This study focuses on the dynamic responses of ECs to brief periods of low FSS, examining its impact on endothelial traction-a measure of …

Low Shear In Short-Term Impacts Endothelial Cell Traction And Alignment In Long-Term, Mohanish K. Chandurkar, Nikhil Mittal, Shaina P. Royer-Weeden, Steven D. Lehmann, Yeonwoo Rho, Sangyoon J. Han

Michigan Tech Publications, Part 2

Within the vascular system, endothelial cells (ECs) are exposed to fluid shear stress (FSS), a mechanical force exerted by blood flow that is critical for regulating cellular tension and maintaining vascular homeostasis. The way ECs react to FSS varies significantly; while high, laminar FSS supports vasodilation and suppresses inflammation, low or disturbed FSS can lead to endothelial dysfunction and increase the risk of cardiovascular diseases. Yet, the adaptation of ECs to dynamically varying FSS remains poorly understood. This study focuses on the dynamic responses of ECs to brief periods of low FSS, examining its impact on endothelial traction—a measure of …

Droplet Jump From A Particle Bed, Karl Cardin, Facundo Cabrera-Booman, Raúl Bayoán Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Drop tower experiments have been performed to study droplet jump from a particle bed across a wide range of fluid viscosities. Here the droplet jumps from the particle bed in response to the apparent step reduction from terrestrial gravity to microgravity when the experiment is dropped and enters free fall. The presence of a particle layer has been found to affect contact line dissipation and the overall jumping behavior of droplets. Additionally, the study has identified the impact of the Ohnesorge number (Oh) on droplet morphology. The investigation has yielded results that not only validate a modified version of the …