Engineering Commons^™

A Software System For Interactive Man-Machine Design And Analysis Of Electronic Circuits, Leo William Midden

Masters Theses

"The development of an interactive computer-aided circuit analysis program is presented. A graphics terminal is used as an I/O device while an SCC 650 mini-computer is used as peripheral processor. The central processor is an IBM 360/50.

Formulation, capabilities and use of the system are discussed in detail. Close attention is given to user control, making the system both useful and versatile. Both hard and soft copies of all plots and tabular data are available. Provisions are made for error corrections and changes at each step of the input. Parameter values can be altered before and after each analysis.

Additionally, …

Practical Application Of Digital Computer To Distribution Systems, Juan Vincente Saavedra

Masters Theses

"Given a three phase ac power distribution system, a digital computer program is presented which determines a complete steady state solution for a given condition. The network data is processed by the computer into an admittance matrix, and these parameters are stored in a manner that enables the computer program to operate upon them as the coefficient of a simultaneous set of nonlinear equations. This set of equations are solved by the Gauss-Seidel Iterative Process improved by a modification of the relaxation method. Practical experience with the distribution system of the Davenport, Iowa, plant of the Aluminum Company of America …

The Effect Of Channel Errors In The Differential Pulse-Code-Modulation Transmission Of Sampled Imagery, Roger J. Arguello, Harvey R. Sellner, John A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

This Paper Presents an Analysis, Simulation, and Discussion of the Effects of Communication Errors on Four-Bit Differential Pulse-Code Modulation (DPCM) Sampled Imagery. Simulations Are Presented that Describe the Effects of Inserting Periodic "PCM Updates" in Order to Correct Communication Errors in the DPCM Transmission of Photographic Scenes that Have Been Scanned and Sampled at the Nyquist Rate. Copyright © 1971 by the Institute of Electrical and Electronics Engineers, Inc.

Detection Of Delay Time And Filtering Using Sequency Domain Technique, Earl F. Richards

Doctoral Dissertations

"A procedure is presented by which it is possible to detect a known signal of unknown delay in a noisy medium contaminated by noise. From the results the characteristics of a sequency digital filter which would be required to remove the noise contamination is indicated. The Walsh functions are discussed and the sequency domain, which is analogous to the continuous frequency domain, is used in the spectral analysis of signals. The binary nature of the Walsh functions and their ease of generation makes processing of signals easier than the Fourier analysis approach. The applications of fast forward and inverse Walsh …

Identification Of Linear Systems With Delay Via A Learning Model, Hugh Francis Spence

Doctoral Dissertations

"The effects of input delay on an identification scheme using a learning model are investigated. The parameter adjustment laws for the learning model are derived through Lyapunov methods similar to those used for the model reference adaptive control systems of Parks. For no measurement noise or delay mismatch between the learning model and system, the parameters are adjusted to bring the error between model and plant to zero. When there is delay mismatch between the inputs of the learning model and the unknown system, the convergence of the parameters of the learning model to those of the unknown system is …

Raman Scattering From Localized Vibrational Modes In Gap, D. T. Hon, W. L. Faust, W. G. Spitzer, P. F. Williams

P. F. (Paul Frazer) Williams Publications

High-frequency localized vibrational modes of impurities in a III-V compound have been observed by Raman scattering. Three lines from the GaP samples closely correspond to some loccal modes previously reported in infrared studies, and depolarization measurements tend to confirm their proposed assignments. We describe several attractive features of this method for the study of semiconductor impurities.

Longitudinal Modes In A High-Gain Laser, Lee W. Casperson, Amon Yariv

Electrical and Computer Engineering Faculty Publications and Presentations

In lasers employing high‐gain narrow‐linewidth transitions the theory predicts major departures of the mode‐splitting frequencies from their low‐gain values as well as a new type of mode splitting. The first of these effects consisting of a reduction by a factor of 2.5 of the mode splitting in a xenon 3.51‐μ laser is observed experimentally.

Complex Disjunctive Decompositions Of Incompletely Specified Boolean Functions., Stuart Lee Hight

Electrical and Computer Engineering ETDs

This dissertation extends the theory of Ashenhurst and Curtis on complex disjunctive decompositions of Boolean functions. The extension takes this theory into the realm of incompletely specifies Boolean functions, that is, those with don-t-care conditions (phi’s). First, the theory is extended to a simple decomposition through a compatibility relation on incompletely specified Boolean vectors whose elements are 0’s, 1’s and phi’s. This relations is applied to the columns of the decomposition charts used by Curtis and Ashenhurst. To accomplish complex disjunctive decompositions, a new Boolean variable, called a constrained don’t-care is introduced as a component of a new Boolean vector …

The Silicon Micro-Hall Device: Design, Fabrication, And Applications, Roy Arthur Colclaser

Electrical and Computer Engineering ETDs

A family of silicon devices, the micro-Hall devices, are described. These include the diffused, diffused-epitaxial, isolation-diffused-epitaxial, mesa-epitaxial, and silicon-on­sapphire isolation-diffused structures. The design and fab­rication of these devices are presented in complete detail.

The theory of the Hall effect and its applications to the theory of fast neutron displacement damage to silicon is presented. A quantitative model of radiation damage in the form of spherical intrinsic voids representing the damage clusters is described.

Three applications of the isolation-diffused-epitaxial silicon micro-Hall device are discussed in the following paragraphs.

The first of these, the evaluation of epitaxial silicon, has three features which …

A Simplification Heuristic For Large Flow Tables, R. J. Smith, James H. Tracey

Electrical and Computer Engineering Faculty Research & Creative Works

Flow tables specifying large asynchronous sequential circuits often contain more internal states than are required to specify desired circuit behavior. Known minimization techniques appear unsuited for reduction of such large (rows X columns > 250) flow tables, because of excessive computation and intermediate data requirements for problems of this size. The algorithm described here is intended to rapidly produce a simplified-but in general non-minimal-flow table. It is most economical when applied to extremely large tables and was devised primarily for automated design applications. The procedure has been programmed in PL/1 and has been incorporated into an asynchronous sequential circuit design automation …

Reliability Aspects Of Semiconductor Surface Protective Coatings, Robert Edward Mcmillan

Dissertations

This research was directed towards the occurrence and im-portance of surface leakage in reverse biased semiconductor diodes and the relation of this leakage to the reliability of a device under use conditions. As a result of this study, it is possible to predict one important leakage mechanism after such back-biased diode units have been subjected to long periods of temperature and humidity. This theory is consistent with tests of commercially available units, some of which have very slight surface leakage and others very large surface leakage.

Further, the usefulness of various possible passivating coatings is critically analyzed on the basis …

Oscillations In Pulse Frequency Modulated Control Systems, Warren Joseph Guy

Dissertations

This dissertation is concerned with oscillations and their stability which occur in a control system containing two nonlinearities, separated by linear elements. Specifically the nonlinearities are Integral Pulse Frequency Modulators and the linear elements are described by ordinary differential equations which are linear. The IPFM can be modelled by a quantizer with hysteresis and many other PFM laws are related to IPFM, thus the study applies to more than just IPFM alone.

Boundaries on the system parameters are identified within which free oscillation may be possible. These boundaries give sufficient conditions for stability and necessary conditions for instability. Also since …

Vacuum Deposition Of Thin Films Of Ultra-High Thickness Uniformity On Conical Substrates Having Extreme Curvature, Richard Bechtel

Electrical and Computer Engineering ETDs

For many industrial and analytical applications of thin films it is very essential to have a uniform thickness of the deposit. In response to this need, various techniques have been devised that are capable of providing the required uniformity on planar and slightly-curved spherical substrates. However, when a severe curvature (such as that encountered with some conical substrates) is introduced, the deposit uniformity that is obtainable with present techniques becomes quite poor. Thus, the need exists for new technology in this respect. Theoretical consideration is given to the problem of obtaining an ultra-uniform thin film coating on conical substrates. The …

A Study Of An Unintentional Shutdown (Scram) Problem In The Operation Of The High Flux Isotope Reactor, Cheng Ping Wu

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

The High Flux Isotope Reactor (HFIR) at the Oak Ridge National Laboratory experiences occasional operating difficulties caused by temporary low voltage conditions on its main power feeder line. The low voltage causes the shutdown of one or more of the three primary coolant pumps. When two of these pumps are shut down, the capacity of the cooling system is reduced to the point where the reactor is scrammed due to a high inlet coolant temperature.

This study was made to determine the cause of the high inlet temperature when operating with one primary coolant pump and to suggest possible changes …

A Study Of The Secant Law For Sporadic E, Ruey-Yuan Han

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The secant law is the relationship between the frequencies of a vertically incident wave and an obliquely incident wave that are reflected from the same level (i.e., density) of a stratified ionosphere. This thesis investigates the validity of the secant law applied to sporadic E.

Sporadic E data from two backscatter sounders and one vertical incidence ionosonde located in Japan were studied to test the validity of the secant law. The B-scan photos of the backscatter sounders were searched for E_s patches which were then compared with the sporadic E parameters defined for vertical incidence ionograms.

Finally, two theoretical …

Electrical Lighting Design, Thermthip Chamarakula

Graduate Research Papers

In any given space for lighting design, each space presents a unique lighting problem which must be studied. These problems can be considered as physical characteristics of the space and its occupancy and usage.

With respect to. these problems a number of questions must be asked.

1. What are the actual seeing tasks?

2. Is the usage uniform or are different areas utilize< for seeing tasks of varying severity?

3. How should the lighting equipment be?

4. How can the proper quantity and quality of light be established?

5. Will the area be used during both daylight hours and at night, and, if so, are the …

On The Performance Of Some Sequential Multiple-Decision Procedures, Thomas S. Edrington Ii

Electrical and Computer Engineering ETDs

The performance of several sequential procedures for the following multiple-decision problem is investigated. Samples from k random processes (or populations) are available, k at a time (one from each process), to a receiver or data processor. One process contains a signal; the other k - 1 are statistically-identical noise. The receiver is to select the odd process (locate the signal), with prescribed probability of error. The optimal receiver makes the selection in minimum average time. All computation is done under the hypothesis that the processes sampled are Rayleigh; however, a method for extrapolating results to other cases is given. The …

Systems Reliability Using The Flow Graph, Kenneth Edward Farrier

Dissertations and Theses

The problem of calculating the reliability of a complex system of interacting elements is delineated to a linear system, no element of the system having a reliability distribution in terms of any other e1ement of the system, where only one path is taken through the system at a time. A precise definition is then developed to specify the reliability of the linear, single path at a time, system. A precise and concise generating function is found that effortlessly produces the reliability of the linear, single path at a time, system directly from the reliability flew graph of the system.

State Assignment Selection In Asynchronous Sequential Circuits, Gary K. Maki, James H. Tracey

Electrical and Computer Engineering Faculty Research & Creative Works

Methods already exist for the construction of critical race-free assignments for asynchronous sequential circuits. Some of these methods permit the construction of many assignments for the same flow table. The algorithm presented here consists of two easy to apply tests which select that critical race-free assignment most likely to produce a set of simple next-state equations. The algorithm has been programmed. Copyright © 1970 by The Institute of Electrical and Electronics Engineers, Inc.

Etch Patterns On Zone-Refined Fe, M. E. Straumonis, Chang-Soo Kim

Electrical and Computer Engineering Faculty Research & Creative Works

Upon dissolution of zone-refined Fe in strong acids, mainly three kinds of corrosion patterns were observed in the crystallites of the sections. Regardless of the acids, the {110} plane always appeared on the three patterns in the form of smooth and even steps, ledges, or facets. The {112}, {122}, and {123} planes were also developed but to a much lesser degree. The {100} and {111} planes were not observed because grains of the respective orientation were missing on the sections. Attempts were made to explain the formation of the planes by taking into consideration the reticular density of the planes …

Nuclear Radiation Enhancement Of Transistor Forward Gain At High Frequencies, C. A. Goben, Y. P. Han

Electrical and Computer Engineering Faculty Research & Creative Works

This investigation has characterized the effects of fast neutron bombardment on a typical n-p-n transistor (2N914) of a common emitter amplifier operating at high-frequencies (>100 MHz) by means of s-parameter measurements from 120 MHz to 350 MHz, inclusive, every 10 MHz. The changes in the four (4) s-parameters and the trends and consequences of neutron bombardment are examined pictorially on graphs. The general effect of fast neutron bombardment is to decrease the magnitude of each s-parameter for frequencies below z. fT (where z = (O/1013)0.1). However, if the device is operating above z fT, the magnitudes of s11 (input …

Neutron Dependence Of Neutral Base Region Recombination, J. Bereisa, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

A discrete, deterministic mathematical model has been developed for the bulk base region of graded base devices that accounts for both the effects of neutron-induced recombination and built-in electric field in the base region at low, intermediate, and moderate current/injection levels. Exact expressions are developed for the bulk base recombination current and the collector current as functions of neutron fluence. Exact expressions are derived for the base recombination term and the relative rates of neutron-induced base current increase and collector current decrease. These expressions involve exponential and hyperbolic functions and are well suited for numerical computations and theoretical analysis. Damage …

Excitation Requirement For Rectified Output Ac Generators, Richard Thomas Smith

Electrical and Computer Engineering Faculty Research & Creative Works

This paper develops a method for calculating the required dc field current of a three-phase synchronous ac generator for known dc load conditions and machine characteristics. The method is simple to apply and has shown good agreement with test data. The method is of utility for preliminary design and analysis of rectified output alternators, such as may be used in excitation systems of the largest ac generators, space vehicle power applications, or high-power industrial rectification. Copyright © 1971 by The Institute of Electrical and Electronics Engineers, Inc.

Electric Field Strength Dependence Of Surface Damage In Oxide Passivated Silicon Planar Transistors, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

A dependence of surface degradation induced by ionizing radiation in matched oxide-passivated silicon planar epitaxial transistors on junction fringing electric field strength present during exposure is reported. The electric field strength and gamma dose dependence are investigated of the decrease in the forward current gain, hFE (as reflected by the increase in the surface recombination current component), the increase in the surface recombination velocity (as reflected by the increase in the reciprocal of the minority carrier lifetime), and the increase in junction capacitance. Empirical prediction equations have been derived, for matched devices, correlating the normalized base current increase and the …

Baseband Agc In An Am-Fm Telemetry System, Richard S. Simpson, William H. Tranter

Electrical and Computer Engineering Faculty Research & Creative Works

The use of AGc loops at the input and output of the FM link in an AM-FM telemetry system allows the mean-square transmitter deviation to be maintained near maximum value, even though data may be nonstationary. However, errors result because of the inability of the receiver AGc loop to track perfectly gain variations in the transmitter loop. In this paper the general characteristics of AGc are discussed, and a theoretical analysis is performed to determine the time constant, steady-state error, and tracking error for a first-order loop. Also, tracking error for first order and second-order loops is investigated by simulation. …

An Analysis Of A Synchronization Scheme For 180° Biphase Modulated Signals, James Joseph Spence

Masters Theses

"The problem of analyzing a synchronization system for demodulation of 180° biphase modulated signals is considered in this thesis. The system considered utilizes the so-called squaring loop technique. Techniques derived from the theory of Markov processes are utilized in the analysis of the system. In particular the "fluctuation equation" approach for non-Markovian processes is used. After the analysis of the system is performed, an expression fro the bit error probability is obtained from knowledge of the phase error density function"--Abstract, Page ii.

Digital Simulation Of A Costas Loop Demodulator In Gaussian Noise And Cw Interference, Ajay Mugatlal Mehta

Masters Theses

"A digital computer model of a Costas loop has been employed to study the effects of Gaussian noise and continuous-wave interference on the detection of biphase modulated signals. The dependence of bit-error probability, mean-square error between input and output, phase-error variance and threshold on signal-to-Gaussian-noise power ratio, interference-to-Gaussian-noise power ratio and frequency offset of the interference have been investigated and compared with previously obtained experimental results. The model has been verified for its accuracy in the case of no noise and when Gaussian noise is present at its input"--Abstract, Page ii.

Z-Form Solution Of Non-Linear Differential Equations, Allen Joseph Rushing

Masters Theses

"The "Z-Forms" developed by Boxer and Thaler from Z-Transform theory are reviewed. Iteration is shown to increase accuracy when Z-Forms are used to obtain numerical solutions to some non-linear differential equations. Machine results are presented for example problems. Error estimates and convergence conditions are discussed. The method is usable only when 2- or 3-digit accuracy is acceptable. For some classes of equations the Z-Form method compares favorably to other numerical methods in time required to set up the problem and in machine time required for solution--Abstract, Page ii.

Fault Detection On Sequential Machines, Chung-Tao David Wang

Masters Theses

"This paper presents an algorithm for deriving an optimum test sequence for detecting faults in a synchronous machine. In this study, the flow table is used as a tool to generate the fault detection tests. The fault stuck-at-1 (or stuck-at-0 ) is said to be present when a permanent signal valued 1 (or 0) appears on a component of the machine. Only single faults are treated . The result of the procedure is one or more test sequences guaranteed to detect a set of faults (F_p). First, sequential machines with feedback lines as memory elements are considered . …

Integrating An Oscilloscope Into A General Purpose Automatic Test System, William Charles Bauer

Masters Theses

"The General Purpose Automatic Test System was developed for the Air Force as a system to automatically test and fault isolate an electronic unit under test. The Test System is a building block concept and this paper developed the hardware and programming software necessary to integrate an oscilloscope into the system. A Tektronix Type 564 oscilloscope with a Tektronix Type 3A5 Programmable Amplifier and a Tektronix Type 3B5 Programmable Time Base was used. A prototype of the digital and analog interface between the Test System and the Tektronix System was built and demonstrated. The Oscilloscope Building Block displays waveforms only …