Engineering Commons^™

Fabrication And Characterization Of Silicon Field Emitter Arrays, Aaron M. Brock

Electrical & Computer Engineering Theses & Dissertations

Field emission is a process through which the application of a large electric field to the surface of a material causes electron emission into vacuum. The electron emission current is a strong function of the geometry of the emitting material. The focus of this thesis is to investigate the effect of geometry on the emission current. Specifically, silicon field emitter arrays were fabricated using two separate fabrication processes termed the standard process and the new process. The uniformity of the arrays was measured experimentally. The arrays were used in field emission tests from which parameters controlling field emission were extracted. …

Studies Related To The Design And Implementation Of A Magnetic Suspension And Balance System, Syed Adeel Akhtar Jafri

Electrical & Computer Engineering Theses & Dissertations

This thesis presents studies related to the magnetic suspension and balance system (MSBS) of the Princeton/ONR High Reynolds Number Testing Facility (HRTF). The main motivation for developing the MSBS is to provide interference free aero/hydrodynamic testing of submersible models, which will lead to more accurate measurements. From the controls point of view, the main specification of the MSBS is to robustly control the position of a submersible model in five degrees of freedom (DOF), including three translational as well as pitching and yawing positions. The MSBS should not only regulate the submersible model's position but should also allow for small …

Laboratories Teaching Concepts In Microcontrollers And Hardware-Software Co-Design, Daryl G. Beetner, Hardy J. Pottinger, Kyle Mitchell

Electrical and Computer Engineering Faculty Research & Creative Works

Hardware software co-design is becoming increasingly important to the embedded systems industry. It will soon be fundamental to digital systems design. As such, students in electrical and computer engineering and in computer science should be introduced to hardware-software co-design early in their undergraduate education.

We are designing laboratory modules which introduce concepts of hardware-software co-design in an undergraduate's first course on microcontrollers and digital systems design. Students use design automation tools to develop FPGA-based hardware for use with an 8051-microcontroller and use common software development tools to develop microcontroller software in C or assembly language. Co-simulation of hardware and software …

Dc Power Bus Design With Fdtd Modeling Including A Dispersive Media, Xiaoning Ye, Jun Fan, Marina Koledintseva, James L. Drewniak

Electrical and Computer Engineering Faculty Research & Creative Works

DC power-bus modeling in high-speed digital design using the FDTD method is reported here. The dispersive medium is approximated by a Debye model to account for the loss. A wide band frequency response (100 MHz-5 GHz) is obtained through a single FDTD simulation. Favorable agreement is achieved between the modeled and measured results for a typical DC power-bus structure with multiple SMT decoupling capacitors mounted on the board. The FDTD tool is then applied to investigate the effects of local decoupling on a DC power-bus. The modeled results agree with the results from another modeling tool, the CEMPIE (a circuit …

Lip Feature Extraction Towards An Automatic Speechreading System, Xiaozheng Zhang, Russell M. Mersereau

Electrical Engineering

The use of color information can significantly improve efficiency and robustness of lip feature extraction capability over purely grayscale-based methods. Edge information provides another useful tool in characterizing lip boundaries. In this paper we present a method of integrating both types of information to address the problem of lip feature extraction for the purpose of speechreading. We first examine various color models and view hue as an effective descriptor to characterize the lips due to its invariance to luminance and human skin color, and its discriminative properties. We use prominent red hue as an indicator to locate the position of …

Dielectric Tensor For Interfaces And Individual Layers In Magnetic Multilayer Structures, Xiang Gao, Michael J. Devries, Daniel W. Thompson, John A. Woollam

Department of Electrical and Computer Engineering: Faculty Publications

The magneto-optical Kerr response of metallic magnetic multilayers has been studied by determining the dielectric tensors (dielectric functions) for individual layers, including the magnetic and nonmagnetic interfacial layers. The diagonal components of these tensors were determined using in situ ellipsometric analysis, where the ellipsometric data were taken in real time during multilayer deposition. The off-diagonal components were determined by regression fitting magneto-optic polar Kerr rotation and ellipticity data to models supported by electromagnetic theory. The Voigt parameters (ratio between off-diagonal and diagonal components of dielectric tensors) were determined from these model fits. Higher magnitudes for the Voigt parameters were found …

Self-Organization In Porous 6h–Sic, S. Zangooie, John A. Woollam, H. Arwin

Department of Electrical and Computer Engineering: Faculty Publications

Pores in porous 6H–SiC were found to propagate first nearly parallel with the basal plane and gradually change direction and align with the c axis. As a consequence, well-defined columnar pores were formed. It was shown that the rate of change of propagation directions was influenced by the etching parameters, such as hydrofluoric acid concentration and current density. Larger currents resulted in formation of larger pores. Pore sizes were found to increase with depth due to a decrease of the acid concentration. In addition, due to chemical etching effects, larger pore sizes were obtained close to the sample surface.

Multiresolution Gradient-Based Edge Detection In Noisy Images Using Wavelet Domain Filters, Yunwoo Lee, Samuel Peter Kozaitis

Electrical Engineering and Computer Science Faculty Publications

We detected edges in noisy images using multiresolution analysis with the wavelet transform. Products of wavelet coefficients at several scales were used to identify and locate edges. We found that it was important to consider the changes in edge position at different scales to detect edges in noisy imagery. We analyzed one-dimensional edges and compared the results of our approach with the first derivative of the signal. In addition, we compared the results of noisy images with another wavelet-based edge detection method. Our results led to improved edge detection in noisy images.

Performance Monitoring In Umr's Solar Car, Louis Mccarthy, Josh Pieper, Aaron Rues, Cheng-Hsiao Wu

Electrical and Computer Engineering Faculty Research & Creative Works

We describe the instrumentation in UMR's solar car. Accurate knowledge of the operating parameters inside the solar car is shown to be crucial to maintaining high efficiency and reliability. The power trackers keep the solar array operating at its highest efficiency by conditioning the input and maintaining the maximum power point of the solar cells.

Reduction Of Peak To Average Power Ratio In Ofdm And Ofdm-Cdma System, Jie Cheng

Theses

High Peak to Average Power Ratio is a main problem in Orthogonal Frequency Division Multiplexing(OFDM) system and Orthogonal Frequency Division Multiplexing -Code Division Multiple Access (OFDM-CDMA) system. Considering a compensated High Power Amplifier(HPA), in order to keep linearity for amplification, Input Back-Off(IBO) of the HP-A, has to be increased for handling a high PAPR. Higher 1130 will make HPA less efficient. Additionally, a signal with high PAPR will suffer clipping when PAPR is larger than 1130 of the HPA. Clipping can cause the distortion of the signal and deteriorate the performance of the system. Reduction of PAPR is a main …

Phase Tunability In A Conductor Backed Coplanar Waveguide Patch Antenna, Idan Mandelbaum

Theses

Traditionally beam steering in phase array antenna systems is achieved using tunable phase shifters or switched feed networks. Here, a tunable patch antenna element is suggested as a novel alternative to a combination of a radiating element and a phase shifter. A conductor backed coplanar waveguide patch antenna is chosen due to its suitability to mounted external tuning elements, using varactor diodes. Limited types of lumped tuning circuits, using varactor diodes, have been tested, though a lumped as well as distributed tuning is feasible in the chosen antenna configuration. Approximate analytical models for coplanar waveguide patch antennas with finite ground …

Relative Intensity Noise Characteristics Of Injection-Locked Semiconductor Lasers, Xiaomin Jin, Shun-Lien Chuang

Electrical Engineering

An experimental and theoretical study of relative intensity noise (RIN) spectra of side-mode injection-locked Fabry–Perot semiconductor lasers is reported. It is shown that the injection-locking technique effectively increases the relaxation oscillation frequency from 4.5 GHz (free-running mode) to 12 GHz (injection-locked mode) and enhances relaxation peaks of the slave laser RIN spectra. Results from our theoretical model, which include the key parameters for semiconductor quantum-well lasers, such as the linewidth enhancement factor, the nonlinear gain saturation coefficients, and optical confinement factor, show good agreement with our experimental results.

The Effect Of Cerium On The Anodic Behavior Of Pb-Ca-Sn Alloy In Sulfuric Acid Solution, Hou-Tian Liu, Jiong Yang, Hai-He Liang, Ji-Hua Zhuang, Wei-Fang Zhou

Journal of Electrochemistry

The cyclic voltammograms for Pb - 0.5 at% Ca - 1.5 at% Sn and Pb - 0.5 at% Ca - 1.5 at% Sn containing a certain amount of cerium in 4.5 mol·dm^-3 H₂SO₄ at 20℃ were measured between 0.6 V and 1.4 V(vs. Hg/Hg₂SO₄). The growth rate of the anodic Pb(Ⅱ) films formed on the mentioned alloy electrodes at 0.9 V in the same sulfuric acid medium was investigated using the Linear Sweep Voltammetry. The variation with electrode potential of the real part of the impedence (Z’) for the anodic Pb(Ⅱ) films …

The Electro-Catalytic Oxidation Of Hcooh On Electrodeposited Pd Electrode, Quan Zhou, Cun-Zhong Zhang, Xiao-Lin Lu, Zhong-Da Wu

Journal of Electrochemistry

The coherent electroplates were prepared by electro depositing Pd on supporting materials glassy carbon. The surface morphology of the electrodes was examined by SEM. The electro oxidation of HCOOH in HClO₄ solution was investigated by using cyclic voltammetry. The results show that the deposited conditions in the preparation of electrodes by electro depositing Pd affect the electrodes electro catalytic activity to the oxidation of HCOOH. The platinized Pd electrode on GC substrates using large current density is of higher catalytic activity to the oxidation of HCOOH than Pd electrode. The electro catalytic activity of PdO formed on the Pd …

A Study On Stochastic Resonance For The Process Of Active-Passive Transition Of Iron In Sulfuric Acid, Hong-Bo Ding, Bao-Yun Xia, Chun-Sheng Yin, Zhong-Xiao Pan, Renato Seeber

Journal of Electrochemistry

The bistable characteristics of the process of active passive transition of iron in sulfuric acid was described and the stochastic resonance phenomenon in the process was simulated.

Algan/Gan Metal-Oxide-Semiconductor Heterostructure Field-Effect Transistors On Sic Substrates, M. Asif Khan, X. Hu, A. Tarakji, Grigory Simin, J. Yang, R. Gaska, M. S. Shur

Faculty Publications

We report on AlGaN/GaN metal–oxide–semiconductor heterostructurefield-effect transistors (MOS-HFETs) grown over insulating 4H–SiC substrates. We demonstrate that the dc and microwave performance of the MOS-HFETs is superior to that of conventional AlGaN/GaN HFETs, which points to the high quality of SiO₂/AlGaNheterointerface. The MOS-HFETs could operate at positive gate biases as high as +10 V that doubles the channel current as compared to conventional AlGaN/GaN HFETs of a similar design. The gate leakage current was more than six orders of magnitude smaller than that for the conventional AlGaN/GaN HFETs. The MOS-HFETs exhibited stable operation at elevated temperatures up to 300 …

Cathodic Indirect Oxidation Of Organic Compounds(Ⅱ)——Cathodic Indirect Epoxidation Of Olefine, Xue-Ying Zhang, Bao-Qiu Cui, Deng-Ping Gu, Wei Li

Journal of Electrochemistry

We described a novel cathodic indirect epoxidation system in which O₂ was first cathodically reduced to H₂O₂. Then VO(acac)₂ was oxidized by H₂O₂ homogeneously to VO(acac)₂OOH which was used to epoxidize some olefine such as maleic, fumaric and crotonic acids. Many affecting factors on the current efficiency were optimized. The research will contribute to the developments of organic electrosynthesis.

The Study On Lithiated Titanium Composite Oxides As Negative Electrode For Lithium-Ion Battery, Xiao-Yan Yang, Shou-Nan Hua, Shu-Yong Zhang

Journal of Electrochemistry

Lithiated titanium composite oxides Li₄Ti₅O₁₂ were prepared from Li₂CO₃ and TiO₂. The XRD results of this composite oxides indicated that the compound had a spinel structure. The electrochemical behavior of lithiated titanium composite oxides was examined. The results showed that this material had an excellent cyclic capability and reversibility for lithium insertion, and had high specific capacity: the initial discharge capacity was 300 mAh·g^-1 , and the reversible capacity was 100 mAh·g^-1 . The discharge plateau (about 1.5 V) and the charge plateau (about 1.6 V) were very …

Studies Of The LialYNi1-YO2 As Cathode Materials For Rechargeable Lithium Ion Batteries, Xiao-Gan Li, Wei-Hua Qiu, Chuan-Gang Lin, Qing-Guo Liu

Journal of Electrochemistry

In this paper, we have synthesized series of single-phase LiAl_yNi_1-yO₂ (differentive in value-y) by solid reaction. Through examining their electrothemical properties, found that, under a proper sintering condition, Li_xAl_0.25Ni_0.75O₂ solution for cathode materials of rechargeable lithium ion batteries showed more pleasing properties in overcharge-resist and cycling life (vs LiNiO₂). When x>1, the capacity can be kept 125mAh/g after 30 cycles under higher charged/discharged voltages ranging from 3.0 V to 4.8 V, whereas that of pure LiNiO₂ has only 61 nAh/g after 25 cycles. The …

A Study On The Cylindrical Zinc-Air Battery, Sheng-Sian Li, Gui-Mao Zhou, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

The zinc air battery has advantages of high specific energies and low cost, therefore attracts much interests. However, its application is limited only in prismatic and button type.This paper reported a novel design of cylindrical zinc air batteries and the performances of the batteries tested at various conditions. The results showed that when discharged at the current of 40 mA at 20 °C, the capacity of AA size and AAA size batteries reached 4000mAh and 1400mAh respectively, corresponding to the energy densities 280 Wh/kg and 200 Wh/kg. The effects of the discharge current, temperature and humidity on the performances of …

Synthesis Of Li1+XMn2O4 Cathode Material For Lithium-Ion Batteries With Solution Method, Pei-Song Liu, Sing-Quarn Liu, Qing Li, Zhao-Yong Chen, Bai-Lan Zhang, Zuo-Long Yu

Journal of Electrochemistry

The cathode materials Li_1+xMn₂O₄ were prepared with citric acid complexing and solution impregnating methods. Structure characterization and specific surface area test were performed by means of XRD, BET methods, the influences of calcination temperature, Li/Mn molar ratio and raw materials on the structure and electrochemical capacity of samples have beem examined. The results showed that the Li/Mn molar ratio and calcimation temperature were the key factors affecting the electrochemical capacity of cathode materias. The optimum conditions for synthesis of  Li_1+xMn₂O₄ cathode material were 0≤x≤0.05 and calcined at 750°C. The initial …

The Effect Of Anode Thickness In Sofcs With Anode Supported Ysz Film, Yi-Huang Zhang, Yi Jiang, Zi-Gui Lu, Yong-Lai Dong, Jing-Wang Yan

Journal of Electrochemistry

Solid oxide fuel cells with supported yttria stabilized zirconia electrolyte films on anode substrates of various thickness have been fabricated. The electrochemical performances of the SOFCs have been examined. The results showed that the cell performance was limited by the anodic overpotential, which is caused mainly by a concentration polarization when the anode substrate is thick. The anodic overpotential was reduced obviously as the thickness of anode substrate was decreased. As a result, the performance of the SOFC cell was improved. With a 0.5 mm anode substrate, a SOFC cell produced a power density about 0.19 W/cm² at 800 …

A New Method For The Preparation Of The Electrodes With Very Low Platinum Loading Used In Proton Exchange Membrane Fuel Cell, Zhi-Gang Shao, Bao-Lian Yi, Ming Han, Ya-Guang Qiao, Hao Liu, Jing-Rong Yu

Journal of Electrochemistry

Research and development on low platinum loading electrode is very important in reducing the cost of proton exchange membrane fuel cell(PEMFC) stack. This paper has put forward a new method to prepare the electrode of PEMFC. The pore forming substances were used in this methd. The low platinum loading electrodes (0.02 mg_Pt⋅cm^-2) have already been prepared with the method. Compared with the traditional method, the new method is simple, cheep, and easy to scale up. The superior composition of the electrodes is catalyst: pore forming substance: Nafion= 3:3:1. The performance of a single cell using this …

Method Of Testing And Diagnosing Field Programmable Gate Arrays, Miron Abramovici, Eric Seng-Kar Lee, Charles Eugene Stroud

Electrical and Computer Engineering Faculty Patents

A method of testing field programmable gate arrays (FPGAs) includes establishing a first group of programmable logic blocks as test pattern generators or output response analyzers and a second group of programmable logic blocks as blocks under test. This is followed by generating test patterns and comparing outputs of two blocks under test with one output response analyzer. Next is the combining of results of a plurality of output response analyzers utilizing an iterative comparator in order to produce a pass/fail indication. The method also includes the step of reconfiguring each block under test so that each block under test …

All-Solid-State Electrochromic Reflectance Device For Emittance Modulation In The Far-Infrared Spectral Region, E. B. Franke, C. L. Trimble, Mathias Schubert, John A. Woollam

Department of Electrical and Computer Engineering: Faculty Publications

All-solid-state electrochromic reflectance devices for thermal emittance modulation were designed for operation in the spectral region from mid- to far-infrared wavelengths (2–40 μm). All device constituent layers were grown by magnetron sputtering. The electrochromic (polycrystalline WO₃), ion conductor (Ta₂O₅), and Li⁺ ion-storage layer (amorphous WO₃), optimized for their infrared (IR) optical thicknesses, are sandwiched between a highly IR reflecting Al mirror, and a 90% IR transmissive Al grid top electrode, thereby meeting the requirements for a reversible Li⁺ ion insertion electrochromic device to operate within the 300 K blackbody emission …

Process Modeling, Monitoring And Control Of Laser Metal Forming, N. Munjuluri, Sanjeev Agarwal, Frank W. Liou

Electrical and Computer Engineering Faculty Research & Creative Works

Laser Metal Forming (LMF) process is one of the prominent Rapid Prototyping (RP) process that can be used to develop functional and fully dense metal parts. This paper addresses process modeling, monitoring and control of a laser metal forming system currently under development at Laser Aided Manufacturing Processes (LAMP) laboratory at University of Missouri--Rolla. This LMF system is based on a 2.5kW Nd:YAG laser as energy source and integrates five axis metal deposition and five axis machining. The current paper is aimed at characterization of effects of operating parameters such as traverse speed, mass flow-rate and laser power on the …

Sio2-Passivated Lateral-Geometry Gan Transparent Schottky-Barrier Detectors, V. Adivarahan, Grigory Simin, J. W. Yang, A. Lunev, M. Asif Khan, M. Pala, M. Shur, R. Gaska

Faculty Publications

We report on a transparent Schottky-barrierultraviolet detector on GaN layers over sapphire substrates. Using SiO₂ surface passivation, reverse leakage currents were reduced to a value as low as 1 pA at 5 V reverse bias for 200 μm diameter device. The device exhibits a high internal gain, about 50, at low forward biases. The response time (about 15 ns) is RC limited, even in the internal gain regime. A record low level of the noise spectral density, 5×10⁻²³ A²/Hz, was measured at 10 Hz. We attribute this low noise level to the reduced reverse leakage current.

Analysis Of The Anodic Bonding Process And The Packaging Effects In Mems Devices, Sonya G. Iyasere

Electronic Dissertations and Theses

This paper gives a brief overview of the process of completely sealing and permanently joining glass to a semi-conductor without the use of adhesives known as anodic or electrostatic bonding. It is well known that this process will introduce thermal strain due to different coefficients of thermal expansion between any metal or semiconductor and glass. This paper will also describe the effect of the MEMS packaging process on various devices that are bonded electrostatically.

Emi From Airflow Aperture Arrays In Shielding Enclosures-Experiments, Fdtd, And Mom Modeling, Min Li, Joe Nuebel, James L. Drewniak, Richard E. Dubroff, Todd H. Hubing, Thomas Van Doren

Electrical and Computer Engineering Faculty Research & Creative Works

Aperture arrays designed to provide airflow through shielding enclosures can provide part of the coupling path from interior sources to external electromagnetic interference (EMI). In this work, radiation through aperture arrays is investigated numerically and experimentally. FDTD modeling is compared with measurements on aperture arrays in a test enclosure. The method of moments (MoM) is also utilized to study radiation from apertures and to investigate the mutual coupling between apertures in an infinite conducting plane. A simple design equation for the relation between aperture size and number and shielding effectiveness is proposed.

Experimental And Numerical Study Of The Radiation From Microstrip Bends, H. Wang, Yun Ji, Todd H. Hubing, James L. Drewniak, Thomas Van Doren, Richard E. Dubroff

Electrical and Computer Engineering Faculty Research & Creative Works

This paper investigates the radiation from microstrip lines with 90-degree bends. A 1-GHz TEM cell is used to measure the radiation from microstrip lines with different kinds of bends. A full wave hybrid FEM/MoM code is used to compute the radiation. Both experimental and numerical results show that there is no significant difference between the radiation from right angle bends and bends with two 45-degree corners at frequencies and trace dimensions that are likely to be found on printed circuit boards.