Engineering Commons^™

Characterization And Electrochemical Investigation Of Boron-Doped Mesocarbon Microbeads Anode Materials For Lithium-Ion Battery, Mao-Hui Chen, Guo-Tao Wu, Guang-Ming Zhu, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

The anodic performances of boron doped and undoped mesocarbon microbeads(MCMBs) were comparatively studied and the structures were characterized by XPS, SEM, XRD and electrochemical measurements. It was found that boron doping samples greatly increased the degree of graphitization and the crystallite size, leading to quite different morphology. Electrochemical discharge/charge cycle tests indicate that lithium intercalation occurred at a little higher potential for the boron doped MCMBs, being attended by greater irreversible capacity loss.

Optimization Of Real-Time Protocols For Wireless Packet-Switched Multimedia Networks Based On Partially Observed Multivariate Point Processes, William S. Hortos

Electrical Engineering and Computer Science Faculty Publications

Next-generation wireless networks have been designed to transport integrated multimedia services based on a cellular extension of a packet-switched architecture using variants of the Internet protocol (IP). Each call, arriving to or active within the network, carries demand for one or more services in parallel, where each service type has a guaranteed quality of service (QoS). Admission of new calls to the wireless IP network (WIN) from the gateway of a wired network or from a mobile subscriber (MS) is allowed by call admission control (CAC) procedures. MS roaming among the nodes of the WIN is controlled by handoff procedures …

Wku Capital Construction Update, Wku Board Of Regents

Board of Regents Documents

Presentation booklet regarding capital construction projects with photographs. Projects included:

• Glasgow Regional Postsecondary Education Center
• Elizabethtown Regional Postsecondary Education Center
• Media & Technology Center / Guthrie Tower & Plaza
• Science & Engineering Building
• Downing University Center Renovations
• University Boulevard Pedestrian Bridge

Modeling, Fabrication, And Optimization Of Niobium Cavities – Phase I: Quarterly Progress Report May 15, 2001 - August 15, 2001, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Multipacting is one of the major loss mechanisms in rf superconductivity cavities for accelerators. This loss mechanism limits the maximum amount of energy/power supported by the cavities. Optimal designs have been identified in others’ studies. In practice, these designs are not easily manufactured. Chemical etching processes used to polish the cavity walls result in a nonuniform surface etch compromising the optimal geometrical design. Past multipacting studies have not examined the impact of wall perturbations.

It is the purpose of this study to examine the chemical etching process in the design of niobium cavities so to maximize the surface quality of …

Pulsed Atomic Layer Epitaxy Of Quaternary Alingan Layers, J. Zhang, E. Kuokstis, Q. Fareed, H. Wang, J. Yang, Grigory Simin, M. Asif Khan, R. Gaska, M. Shur

Faculty Publications

In this letter, we report on a material deposition scheme for quaternary Al_xIn_yGa_1−x–yN layers using a pulsed atomic layer epitaxy (PALE) technique. The PALE approach allows accurate control of the quaternary layer composition and thickness by simply changing the number of aluminum,indium, and gallium pulses in a unit cell and the number of unit cell repeats. Using PALE, AlInGaN layers with Al mole fractions in excess of 40% and strong room-temperature photoluminescence peaks at 280 nm can easily be grown even at temperatures lower than 800 °C.

Research And Development Of A Hybrid Rapid Manufacturing Process, Frank W. Liou, J. Choi, Robert G. Landers, Vijayakumar Janardhan, S. N. Balakrishnan, Sanjeev Agarwal

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents the research and development of a hybrid rapid manufacturing process being developed at the University of Missouri--Rolla. This process includes a laser deposition and a 5- axis CNC milling system. By combining laser deposition and machining processes, the resulting hybrid process can provide greater build capability and better accuracy and surface finish. The hybrid process can build some features that are difficult to build in using a purely deposition processes. The issues and related approaches in the research and development of the hybrid deposition-machining process, including laser deposition process, system design and integration, process planning, and sensor …

Empirical Modeling And Vision Based Control For Laser Aided Metal Deposition Process, Mallikharjuna R. Boddu, Srinivas Musti, Robert G. Landers, Sanjeev Agarwal, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper gives a brief description of the laser aided manufacturing process. Empirical models describing the process dynamics of the laser aided metal deposition process is developed based on some of the models found in the literature. These models provide the basis for process planning and real time control. An embedded vision system, a two color temperature sensor, and a laser displacement sensor are incorporated for real time monitoring and control of the deposition process. The temperature profile of the surface and geometric characteristics of the melt pool are studied to ensure consistent operation of the process.

Differential Signalling In Pcbs: Modeling And Validation Of Dielectric Losses And Effects Of Discontinuities, R. Araneo, Chen Wang, Xiaoxiong Gu, S. Celozzi, James L. Drewniak

Electrical and Computer Engineering Faculty Research & Creative Works

This paper focuses on differential signal transmission above ground planes with gaps, taking into account the dielectric and conductive losses of the substrate. An equivalent lumped-circuit is proposed and its suitability is investigated by comparing the obtained numerical results with the measured data. Furthermore the differential to common mode conversion of the waves, while crossing the gap, is theoretically analyzed and experimentally verified.

Grounding Of Heatpipe/Heatspreader And Heatsink Structures For Emi Mitigation, Chen Wang, James L. Drewniak, D. Wang, Ray Alexander, James L. Knighten, David M. Hockanson

Electrical and Computer Engineering Faculty Research & Creative Works

EMI problems caused by the presence of heatpipe/heatspreader and heatsink structures in a high-speed design are well known in engineering practice. High-frequency noise can be coupled from IC packages to an electrically conductive heatsink or heatspreader attached to the IC, which then is radiated, or the energy coupled to an enclosure cavity mode. This EMI coupling path was modeled with the finite-difference time-domain (FDTD) method, and a mitigation approach was investigated. Good agreement between measurements and FDTD modeling is demonstrated, indicating FDTD is a suitable tool for analysis and design. Then, several grounding schemes suitable for a heatsink or heatspreader …

Representation Of Gyromagnetic Composite Media For Fdtd Modeling, Marina Koledintseva, James L. Drewniak, Xiaoning Ye

Electrical and Computer Engineering Faculty Research & Creative Works

A composite media containing particles with a high internal field of magnetic anisotropy (hexagonal ferrites) useful for numerous EMC applications in a wide frequency band is considered. Effective constitutive parameters of a high-loss composite gyromagnetic media are represented in the Lorentzian form. It is convenient for the numerical analysis using the finite-difference time-domain (FDTD) algorithm with a recursive convolution procedure. The equations for the electric and magnetic field updating in such media are represented.

Emi Considerations In Selecting Heat-Sink-Thermal-Gasket Materials, Yu Huang, J. E. Butler, M. De Sorgo, Richard E. Dubroff, Todd H. Hubing, James L. Drewniak, Thomas Van Doren

Electrical and Computer Engineering Faculty Research & Creative Works

Specific design criteria are proposed to mitigate radiated emissions from a resonant enclosure excited by a heat sink acting as a microstrip patch antenna source. In this particular application, the EMI mechanism is assumed to be due to coupling from the dominant TM^z₀₁₀ mode to one or more resonant modes associated with the enclosure dimensions. The enclosure is then presumed to radiate, at the enclosure resonance frequencies, through one or more apertures, slots, or seams. The EMI-reduction strategy consists of shifting the resonant frequency of the dominant-patch antenna mode by dielectrically loading the patch antenna with thermal-gasket material …

Passivity-Based Control Of Saturated Induction Motors, Levent U. Gökdere, Marwan A. Simaan, Charles W. Brice

Faculty Publications

A passivity-based controller, which takes into account saturation of the magnetic material in the main flux path of the induction motor, is developed to provide close tracking of time-varying speed and flux trajectories in the high magnetic saturation regions. The proposed passivity based controller is experimentally verified. Also, a comparison between the controllers based on the saturated and nonsaturated magnetics is presented to demonstrate the benefit of the controller based on the saturated magnetics

Real-Time Travel Time Estimation Using Macroscopic Traffic Flow Models, Pushkin Kachroo, Kaan Ozbay, Antoine G. Hobeika

Electrical & Computer Engineering Faculty Research

This paper presents the estimation of travel time on highways based on macroscopic modelling. The focus is on real-time values as compared to average or static values. The macroscopic models are used for distributed and time/space lumped settings and corresponding travel time estimation functions and algorithms are developed. The implications of these algorithms for the implementation of various incident management and traffic control strategies are also discussed.

A General Decomposition For Reversible Logic, Marek Perkowski, Lech Jozwiak, Pawel Kerntopf, Alan Mishchenko, Anas Al-Rabadi, Alan Coppola, Andrzej Buller, Xiaoyu Song, Svetlana Yanushkevich, Vlad P. Shmerko, Malgorzata Chrzanowska-Jeske, Mozammel Huq Azad Khan

Electrical and Computer Engineering Faculty Publications and Presentations

Logic synthesis for reversible logic differs considerably from standard logic synthesis. The gates are multi-output and the unutilized outputs from these gates are called “garbage”. One of the synthesis tasks is to reduce the number of garbage signals. Previous approaches to reversible logic synthesis minimized either only the garbage or (predominantly) the number of gates. Here we present for the first time a method that minimizes concurrently the number of gates, their total delay and the total garbage. Our method adopts for reversible logic many ideas developed previously for standard logic synthesis (such as Ashenhurst/Curtis Decomposition, Dietmeyer’s Composition, non-linear preprocessing …

Design Of A Control System For Fmc Jetway Systems' Teleradial Bridge, Briclyn Jon Rogers

Undergraduate Honors Capstone Projects

FMC Jetway Systems has been manufacturing and servicing airport products for over forty years. These products include passenger boarding bridges, pre-conditioned air units, potable water systems and solid-state 400 hertz converters. Components produced by Jetway can be found on over 190 airports across the world. Their Apron Drive Passenger Boarding Bridge (Fig. 1) is the most versatile and widely used boarding bridge in the world. Only recently has the company aimed at gaining a portion of the quickly expanding market of commuter flights.

An Emi Estimate For Shielding-Enclosure Evaluation, Min Li, James L. Drewniak, S. Radu, Joe Nuebel, Todd H. Hubing, Richard E. Dubroff, Thomas Van Doren

Electrical and Computer Engineering Faculty Research & Creative Works

A relatively simple, closed-form expression has been developed to estimate the EMI from shielding enclosures due to coupling from interior sources through slots and apertures at the enclosure cavity modes. A power-balance method, Bethe's (1944) small-hole theory, and empirically developed formulas for the relation between radiation, and slot length and number of slots, were employed to estimate an upper bound on the radiated EMI from shielding enclosures. Comparisons between measurements and estimated field strengths suitably agree within engineering accuracy.

Investigation Of Pcb Layout Parasitics In Emi Filtering Of I/O Lines, Xiaoning Ye, Geping Liu, James L. Drewniak

Electrical and Computer Engineering Faculty Research & Creative Works

EMI filters are often utilized on I/O lines to reduce high-frequency noise from being conducted or coupled off the PCB and resulting in an EMI problem. However, layout parasitics are usually inevitable in practical circuit design, and the filtering performance may vary. In this study, the impact of the board layout on the filtering performance is investigated by |S₂₁| measurements of sample PCB boards with different filter layouts. The finite-difference time-domain method is applied to model the boards, support the experimental work, and can be used to provide a means for conducting "what-if" engineering studies.

Improving The High-Frequency Attenuation Of Shunt Capacitor, Low-Pass Filters, Christopher N. Olsen, Thomas Van Doren, Todd H. Hubing, James L. Drewniak, Richard E. Dubroff

Electrical and Computer Engineering Faculty Research & Creative Works

Circuit board mounted, shunt capacitive filters are less effective at high frequencies because of the mutual inductance (M) that exists between the input and output ports. An approximate expression for the mutual inductance is M=(μh/2π)ln(h/a); where h=via length and a=radius of the via connecting the capacitor to the return plane. The reduced mutual inductance associated with the new, three-terminal, surface-mounted capacitor results in more than 15 dB increased attenuation compared to two-terminal capacitors over the 0.3-6.0 GHz range with 50 Ω source and load terminations

Including Smt Ferrite Beads In Dc Power Bus And High-Speed I/O Line Modeling, Jun Fan, Shaofeng Luan, James L. Drewniak

Electrical and Computer Engineering Faculty Research & Creative Works

Surface mount technology (SMT) ferrite beads are often used in high-speed digital circuit designs to mitigate noise. The common modeling approach is to include SMT ferrite beads as equivalent lumped LCR circuits. The work presented in this paper included SMT ferrite beads as a frequency-dependent impedance in a PEEC-like modeling tool denoted CEMPIE, a circuit extraction approach based on a mixed-potential integral equation formulation. Agreement with measurements demonstrates the approach. The applications shown are segmentation of power areas for noise isolation, and I/O line filtering.

Mitigating Power Bus Noise With Embedded Capacitance In Pcb Designs, Minjia Xu, Todd H. Hubing, Juan Chen, James L. Drewniak, Thomas Van Doren, Richard E. Dubroff

Electrical and Computer Engineering Faculty Research & Creative Works

This paper investigates the power bus noise and power bus impedance of printed circuit boards with four different kinds of embedded capacitance. These boards have power-ground plane pairs separated by a very thin layer of material with high dielectric permittivity. It is shown that embedded capacitance effectively reduces power bus noise over the entire frequency range evaluated (up to 5 GHz).

Dc Power Bus Noise Isolation With Power Islands, Wei Cui, Jun Fan, Hao Shi, James L. Drewniak

Electrical and Computer Engineering Faculty Research & Creative Works

Segmented power planes are often used for DC power bus noise isolation in multi-layered printed circuit board (PCB) designs. To achieve a desirable noise isolation, different power plane segmentations can be used. A suitable modeling approach, as well as measurements, were employed to study the power bus isolation with several power plane segmentation configurations. The studied geometries included power island designs connected with a conducting bridge, a ferrite bead, and a π-filter. In addition, different conducting bridge widths and power island gap widths were analyzed, and compared. The modeled and measured results show that power plane segmentations with proper designs …

Fast Heuristic Minimization Of Exclusive-Sums-Of-Products, Alan Mishchenko, Marek Perkowski

Electrical and Computer Engineering Faculty Publications and Presentations

Exclusive-Sums-Of-Products (ESOPs) play an important role in logic synthesis and design-for-test. This paper presents an improved version of the heuristic ESOP minimization procedure proposed in [1,2]. The improvements concern three aspects of the procedure: (1) computation of the starting ESOP cover; (2) increase of the search space for solutions by applying a larger set of cube transformations; (3) development of specialized datastructures for robust manipulation of ESOP covers. Comparison of the new heuristic ESOP minimizer EXORCISM-4 with other minimizers (EXMIN2 [3], MINT [4], EXORCISM-2 [1] and EXORCISM3 [2]) show that, in most cases, EXORCISM-4 produces results of comparable or better …

Electromagnetics, David V. Arnold, Richard H. Selfridge, Karl F. Warnick

Faculty Publications

Many applications of electrical engineering require a knowledge of the behavior of voltages and currents in electronic devices and within conductors. In many other situations it is not enough to understand the behavior the voltages and currents in just the conductors and other components, but also the influence of the voltage and current on surrounding materials.

Microcavity Surface Emitting Laser, Stewart Feld, John P. Loehr, James A. Lott

AFIT Patents

A three-dimensional waveguiding structure for a microcavity surface-emitting laser is described in which native aluminum oxide layers provide control of intracavity waveguiding and the laser optical mode structure of the emitted beam. Microcavity lasers described herein account for the blueshift of the emission wavelength as the laser lateral dimensions are reduced to or below the emission wavelength.

Aurora Working Group: Dsr Front End Lvcsr Evaluation — Baseline Recognition System Description, Naveen Parihar, Joseph Picone

Publications

In this document we describe the features of the baseline system to be used in the Distributed Speech Recognition (DSR) front end large vocabulary continuous speech recognition (LVCSR) evaluations being conducted by the Aurora Working Group of the European Telecommunications Standards Institute (ETSI). The objective of these evaluations is to determine the robustness of different front ends for use in client/server type telecommunications applications. As such, our experiments are designed to test the following focus conditions on the DARPA Wall Street Journal (WSJ0) corpus using a 5000-word closed-loop vocabulary and a bigram language model:

1. Additive Noise: six noise conditions …

Fault Tolerant Operation Of Field Programmable Gate Arrays, Miron Abramovici, Charles E. Stroud

Electrical and Computer Engineering Faculty Patents

A method of fault tolerant reconfiguration and operation of a field programmable gate array (FPGA) during normal on-line operation includes selecting a programmable logic block as a programmable logic block under test, testing the programmable logic block under test, and detecting the existence of any faults in the programmable logic block under test. During testing, the programmable logic block under test is repeatedly reconfigured in order to test the programmable logic block completely in all possible modes of operation. Based on the results of the test, a test result indication is sent to a controller in communication with a memory …

Microwave Modulation Of A Quantum-Well Laser With And Without External Optical Injection, Xiaomin Jin, Shun-Lien Chuang

Electrical Engineering

We compare three microwave modulation methods experimentally and theoretically using a semiconductor quantum-well (QW) Fabry–Perot test laser: 1) direct microwave current modulation of the test laser (electrical modulation); 2) optical modulation by an external single-wavelength pump laser with a modulated optical injection power; and 3) electrical modulation of the test laser that is injection locked by an external single-wavelength pump laser with a constant injection power. This is the first direct comparison of the three modulation methods on the same QW laser, to the best of our knowledge. The bandwidth of optical absorption modulation is 7.7 GHz, which is 1.45 …

Near-Field Microwave Non-Invasive Determination Of Nacl In Mortar, Karl Joseph Bois, Aaron D. Benally, R. Zoughi

Electrical and Computer Engineering Faculty Research & Creative Works

In recent years near-field microwave nondestructive testing and evaluation techniques have shown great promise for evaluating different properties of cement-based structures. An important issue regarding the inspection of these structures is the ability to determine the presence and evaluate the content of chloride in them. Chlorides can be introduced in these structures in many different ways including when salts are present in their mixing water. Consequently, for this investigation, two sets of 8" × 8" × 8" (203mm) cubic mortar specimens were prepared each with a water-to-cement (w/c) ratio of 0.5 and 0.6, respectively, and both sets with sand-to-cement ratios …

Feedback Correction Of Angular Error In Grating Readout, Monish Ranjan Chatterjee, Sundaram Ramachandran

Electrical and Computer Engineering Faculty Publications

Angular and wavelength READ beam errors in holographic interconnection systems are often a recurrent problem. Several strategies have been proposed to minimize or eliminate such READOUT misalignments.

Some years ago, Chatterjee and co-workers proposed a method involving READ beam wavelength tuning to correct output angular errors. In this paper, we investigate the possibility of using an acousto-optic (A-O) Bragg cell with optoelectronic feedback to dynamically correct the scattered beam for deviations in the incidence direction of the READ beam of a hologram. The concept here is based on an acoustic frequency feedback strategy used recently by Balakshy and Kazaryan for …

Low Frequency Noise In Gan Metal Semiconductor And Metal Oxide Semiconductor Field Effect Transistors, S. L. Rumyantsev, N. Pala, M. S. Shur, R. Gaska, M. E. Levinshtein, M. Asif Khan, Grigory Simin, X. Hu, J. Yang

Faculty Publications

The low frequency noise in GaNfield effect transistors has been studied as function of drain and gate biases. The noise dependence on the gate bias points out to the bulk origin of the low frequency noise. The Hooge parameter is found to be around 2×10⁻³ to 3×10⁻³.Temperature dependence of the noise reveals a weak contribution of generation–recombination noise at elevated temperatures.