Engineering Commons^™

A Reconfigurable Facts System For University Laboratories, Liangying Dong, Zhiping Yang, Shen Chen, Lin Zhang, Stan Atcitty, Mariesa Crow

Electrical and Computer Engineering Faculty Research & Creative Works

To fully understand the dynamic performance of the multiple flexible ac transmission systems (FACTS) devices, a hardware setup is needed to complement software simulation for university research laboratories. This paper presents the schematic and basic controls of a reconfigurable FACTS system that can be used to realize the major voltage-sourced-converter FACTS topologies: the StatCom, the static synchronous series compensator (SSSC), and the unified power-flow controller (UPFC). Furthermore, the state models and control algorithms for the FACTS devices are proposed. The digital signal processor (DSP)-based control system enables new control methods to be rapidly implemented. The comparison of the experimental and …

Common-Mode Current Due To A Trace Near A Pcb Edge And Its Suppression By A Guard Band, Yoshiki Kayano, Motoshi Tanaka, James L. Drewniak, Hiroshi Inoue

Electrical and Computer Engineering Faculty Research & Creative Works

The common-mode (CM) current due to a trace near a printed circuit board (PCB) edge, and its suppression by a guard band have been studied experimentally and with finite-difference time-domain (FDTD) modeling. As the guard band, copper tape is connected along the entire edge of the ground plane. First, a PCB electromagnetic interference (EMI) coupling path that results from the nonzero impedance of the PCB ground plane is discussed. As the trace is moved closer to the PCB edge, the CM current increases. Then, the effect of the guard band on the CM current is detailed. A guard band parallel …

An Efficient Multirate Simulation Technique For Power-Electronic-Based Systems, Steven D. Pekarek, Oleg Wasynczuk, Eric A. Walters, Juri V. Jatskevich, Charles E. Lucas, Ning Wu, Peter T. Lamm

Electrical and Computer Engineering Faculty Research & Creative Works

A novel multirate method of simulating power-electronic-Based systems containing a wide range of time scales is presented. in this method, any suitable integration algorithm, with fixed or variable time-step, can be applied to the fast and/or slow subsystems. the subsystems exchange coupling variables at a communication interval that can be fixed or varied dynamically depending upon the state of the system variables. the proposed multirate method is applied to two example power systems that include power-electronic subsystems. Increases in simulation speed of 183-281% over established single-rate integration algorithms are demonstrated.

Wide-Band/Dual-Band Packaged Antenna For 5-6 Ghz Wlan Application, Mohammod Ali, Tuangsit Sittironnarit, Huan-Sheng Hwang, Robert A. Sadler, Gerard James Hayes

Faculty Publications

A wide-band/dual-band packaged antenna is proposed for wireless local-area network (WLAN) applications in the 5.15-5.35 GHz and 5.725-5.825 GHz frequency range. The antenna is internal to the housing of a personal digital assistant, such as a Palm organizer, and has the dimensions of 28 by 9 by 3 ram on an FR4 substrate. The antenna meets or exceeds the bandwidth requirements for the dual-band IEEE 802.11a WLAN applications (5.15-5.35 GHz and 5.725-5.825 GHz) within 2:1 voltage standing-wave ratio.

Optimal Calibration Of Pet Crystal Position Maps Using Gaussian Mixture Models, Kelly A. Stronger, Michael T. Johnson

Electrical and Computer Engineering Faculty Research and Publications

A method is developed for estimating optimal PET gamma-ray detector crystal position maps, for arbitrary crystal configurations, based on a binomial distribution model for scintillation photon arrival. The approach is based on maximum likelihood estimation of Gaussian mixture model parameters using crystal position histogram data, with determination of the position map taken from the posterior probability boundaries between mixtures. This leads to minimum probability of error crystal identification under the assumed model.

Laboratory Project In Wireless Fsk Receiver Design, Michael A. Jensen, Cynthia Fuse, Raymond Woodward

Faculty Publications

This paper describes a wireless local area network laboratory project that provides senior and first-year graduate students in microwave engineering courses the opportunity to design, build, and test several passive microstrip components and integrate them into a working system. Students design filters, couplers, amplifiers, diode detectors, quarter-wave transformers, antennas, and stub matching networks in weekly labs that parallel-lectures in a one-semester microwave engineering course. This paper also describes simple inexpensive prototyping and testing methods that have been used in this course. Laboratory materials and technical details of the design are provided on the web for students and educators.

Adaptive Learning For Event Modeling And Pattern Classification, Shuangshuang Dai

Dissertations

It is crucial to detect, characterize and model events of interest in a new propulsion system. As technology advances, the amount of data being generated increases significantly with respect to time. This increase substantially strains our ability to interpret the data at an equivalent rate. It demands efficient methodologies and algorithms in the development of automated event modeling and pattern recognition to detect and characterize events of interest and correlate them to the system performance. The fact that the information required to properly evaluate system performance and health is seldom known in advance further exacerbates this issue.

Event modeling and …

Oblivious Data Hiding : A Practical Approach, Husrev T. Sencar

Dissertations

This dissertation presents an in-depth study of oblivious data hiding with the emphasis on quantization based schemes. Three main issues are specifically addressed:

1. Theoretical and practical aspects of embedder-detector design.

2. Performance evaluation, and analysis of performance vs. complexity tradeoffs.

3. Some application specific implementations.

A communications framework based on channel adaptive encoding and channel independent decoding is proposed and interpreted in terms of oblivious data hiding problem. The duality between the suggested encoding-decoding scheme and practical embedding-detection schemes are examined. With this perspective, a formal treatment of the "processing" employed in quantization based hiding methods is presented. In …

Multi-Spectral Light Interaction Modeling And Imaging Of Skin Lesions, Sachin Vidyanand Patwardhan

Dissertations

Nevoscope as a diagnostic tool for melanoma was evaluated using a white light source with promising results. Information about the lesion depth and its structure will further improve the sensitivity and specificity of melanoma diagnosis. Wavelength-dependent variable penetration power of monochromatic light in the trans-illumination imaging using the Nevoscope can be used to obtain this information. Optimal selection of wavelengths for multi-spectral imaging requires light-tissue interaction modeling. For this, three-dimensional wavelength dependent voxel-based models of skin lesions with different depths are proposed. A Monte Carlo simulation algorithm (MCSVL) is developed in MATLAB and the tissue models are simulated using the …

Ip-Based Virtual Private Networks And Proportional Quality Of Service Differentiation, Jingdi Zeng

Dissertations

IP-based virtual private networks (VPNs) have the potential of delivering cost-effective, secure, and private network-like services. Having surveyed current enabling techniques, an overall picture of IP VPN implementations is presented.

In order to provision the equivalent quality of service (QoS) of legacy connection-oriented layer 2 VPNs (e.g., Frame Relay and ATM), IP VPNs have to overcome the intrinsically best effort characteristics of the Internet. Subsequently, a hierarchical QoS guarantee framework for IP VPNs is proposed, stitching together development progresses from recent research and engineering work.

To differentiate IP VPN QoS, the proportional QoS differentiation model, whose QoS specification granularity compromises …

Pulsed Laser Ablation Deposition And Optical Characterization Of Hexagonal-Wurtzite Silicon, Berzelius Ybanez Cada

Theses

Hexagonal-wurtzite silicon phase silicon is an unusual polymorph of silicon with potentially useful electro-optical properties. Previous studies using a simple deposition system demonstrated that laser ablation of the standard cubic-diamond silicon produces droplets containing hexagonal-wurtzite crystallites. In order to study the process parameters and to deposit larger hexagonal crystals, a new pulsed laser ablation system with variable parameters was assembled and tested. Deposition expenments were performed in high vacuum with different laser pulse power. Raman spectroscopy showed that the new system successfully produces hexagonal-wurtzite silicon. The droplet size distributions, measured with an optical microscope, were found to depend on the …

Configurable Computer Systems Can Support Dataflow Computing, Anish Arvind Sathe

Theses

This work presents a practical implementation of a uni-processor system design. This design, named D²-CPU, satisfies the pure data-driven paradigm, which is a radical alternative to the conventional von Neumann paradigm and exploits the instruction-level parallelism to its full extent. The D²-CPU uses the natural flow of the program, dataflow, by minimizing redundant instructions like fetch, store, and write back. This leads to a design with the better performance, lower power consumption and efficient use of the on-chip resources. This extraordinary performance is the result of a simple, pipelined and superscalar architecture with a very …

Studies In Multiple-Antenna Wireless Communications, Christian Bruce Peel

Theses and Dissertations

Wireless communications systems are used today in a variety of milieux, with a recurring theme: users and applications regularly require higher throughput. Multiple antennas enable higher throughput and/or more robust performance than single-antenna communications, with no increase in power or frequency bandwidth. Systems are required which achieve the full potential of this "space-time" communication channel under the significant challenges of time-varying fading, multiple users, and the choice of appropriate coding schemes. This dissertation is focused on solutions to these problems. For the single-user case, there are many well-known coding techniques available; in the first part of this dissertation, the performance …

A Faster Technique For Distributed Constraint Satisfaction And Optimization With Privacy Enforcement, Marius C. Silaghi

Electrical Engineering and Computer Science Faculty Publications

A problem that received recent attention is the development of negotiation/cooperation techniques for solving naturally distributed problems with privacy requirements. An important amount of research focused on those problems that can be modeled with distributed constraint satisfaction, where the constraints are the secrets of the participants. Distributed AI develops techniques where the agents solve such problems without involving trusted servers. Some of the existing techniques aim for various tradeoffs between complexity and privacy guarantees [MTSY03], some aim only at high efficiency [ZM04], while others aim to offer maximal privacy [Sil03]. While the last mentioned work achieves an important level of …

Low-Frequency Fast Inhomogeneous Plane-Wave Algorithm (Lf-Fipwa), L. (Lijun) J. Jiang, W. C. Chew

Electrical and Computer Engineering Faculty Research & Creative Works

A new method, the low-frequency fast inhomogeneous plane-wave algorithm (LF-FIPWA) is presented to extend the traditional multilevel fast multipole algorithm (MLFMA) and fast inhomogeneous plane-wave algorithm (FIPWA) seamlessly into the low-frequency range. It uses evanescent-wave extrapolation and translation techniques to overcome the low-frequency breakdown problem. The accuracy can be well controlled over a broad frequency range. Numerical examples show the effectiveness of this new algorithm.

Effective Quality Analysis For Video Streaming Over Wireless Ad Hoc Network, Zhihai He, Chang Wen Chen

Electrical Engineering and Computer Science Faculty Publications

Video encoding and streaming over wireless ad hoc network operates under severe conditions, such as time-varying channel characteristics with bursty errors, limit power for data transmission, and dynamic topology of the self-organized network, stringent time delay for packet delivery, etc. Due to the dynamic topology, complex mechanism, and time-varying nature of the wireless ad hoc network, the network system and the streaming service often exhibit unpredictable behaviors. The ultimate goal in the wireless video streaming service is to provide the end user with the best possible video presentation quality. The video streaming quality, often measured by the end-to-end picture distortion, …

Collaborative Image Transmission Over Wireless Sensor Networks, Min Wu, Chang Wen Chen

Electrical Engineering and Computer Science Faculty Publications

The imaging sensors are able to provide intuitive visual information for quick recognition and decision. However, imaging sensors usually generate vast amount of data. Thus, processing of image data collected in the sensor network for the purpose of energy efficient transmission poses a significant technical challenge. In particular, when a cluster of imaging sensors is activated to track certain moving target, multiple sensors may be collecting similar visual information simultaneously. With correlated image data, we need to intelligently reduce the redundancy among the neighboring sensors so as to minimize the energy for transmission, the primary source of sensor energy consumption. …

A Half D1 Mpeg-4 Encoder On The Bsp-15 Dsp, Lulin Chen, Zhihai He, Chang Wen Chen, Michael A. Isnardi

Electrical Engineering and Computer Science Faculty Publications

In this paper, we present the work on implementation of a half-Dl interlaced MPEG-4 encoder with Equator Technology DSP chip, BSP-15. The BSP-15 DSP consists mainly of a VLIW core, Co-processors, and media I/O interfaces. The encoder utilizes several BSP-15 functional blocks in parallel. In general, the VLIW performs pixel processing that is computationally intensive. The VLx coprocessor completes variable length coding. Further parallelism is obtained by pre-loading data cache and doubling data buffers. Given the DSP processing power and real time requirements, a complexity control scheme is implemented. A frame-level quantization scheme with quality and rate control is employed. …

Layered Unequal Loss Protection For Progressive Image Transmission Over Packet Loss Channels, Jianfei Cai, Xiangjun Li, Chang Wen Chen

Electrical Engineering and Computer Science Faculty Publications

In the past, many schemes have been proposed for progressive image transmission using unequal error protection (UEP) or unequal loss protection (ULP). However, most existing UEP/ULP schemes do not consider the minimum image quality requirement and usually have high computation complexity. In this paper, we propose a layered ULP (L-ULP) scheme for progressive image transmission over packet loss channels, which is able to solve the mentioned problems of existing ULP schemes by smartly choosing the layers. The numerical results show that the proposed L-ULP scheme is quite promising for fast image transmission over packet loss networks.

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Second Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The third phase concludes the experimental a fluid flow study and optimization study. The first quarter and second quarter of phase three also begins the experimental set-up of secondary emission studies from niobium in superconducting mode. This …

Optically Coupled Etalons And Methods Of Making And Using Same, Michael A. Scobey, Lucien P. Ghislain, Dennis Derickson, Loren F. Stokes

Electrical Engineering

Optical elements comprise stacked, optically matched and optically coupled etalons, at least one of the optically coupled etalons comprising first and second selectively transparent thin film mirror coatings on opposite surfaces of a bulk optic. The bulk optic defines the cavity spacing of the etalon and may, for example be formed of a monolithic body of silica or other optically transparent glass diced from a glass wafer. The bulk optic may further comprise a wedge coating of progressively increasing thickness overlying the monolithic glass body and compensating for, or offsetting non-parallelism of the bulk optic. The bulk optic may further …

Determination Of The Carrier Concentration In Ingaasn∕Gaas Single Quantum Wells Using Raman Scattering, Patrick A. Grandt, Aureus E. Griffith, M. O. Manasreh, D. J. Friedman, S. Doğan, D. Johnstone

Electrical and Computer Engineering Publications

Raman scattering from longitudinal optical phonon-plasmon coupled mode was observed in a series of InGaAsN∕GaAs single quantum well samples grown by metalorganic vapor phase epitaxy. The phonon-plasmon mode spectra were fitted with the dielectric constant function based on Drude model that contains contributions from both lattice vibrations and conduction electrons. The carrier concentration is calculated directly from the plasmon frequency, which is obtained from the fitting procedure. An empirical expression for the electron concentration, [n], in InGaAsN∕GaAs samples is determined as [n]≈{2.35×1016(ωm−502)}cm−3, where ωm is the peak of the upper frequency branch, L+, of the phonon-plasmon mode measured in unit …

Alternate Spintronic Analog Of The Electro-Optic Modulator, S. Bandyopadhyay, M. Cahay

Electrical and Computer Engineering Publications

There is significant current interest in spintronic devices fashioned after a spin analog of the electro-opticmodulator proposed by Datta and Das [Appl. Phys. Lett.56, 665 (1990)]. In their modulator, the “modulation” of the spin-polarized current is carried out by tuning the Rashba spin-orbit interaction with a gate voltage. Here, we propose an analogous modulator where the modulation is carried out by tuning the Dresselhaus spin-orbit interaction instead, using a split gate. Additionally, the magnetization of the source and drain contacts in our device is transverseto the channel, whereas in the Datta-Dasdevice, it is along the channel. Therefore, in the …

Thermal Stability Of Electron Traps In Gan Grown By Metalorganic Chemical Vapor Deposition, D. Johnstone, S. Doğan, J. Leach, Y.-T. Moon, Y. Fu, Y. Hu, Hadis Morkoç

Electrical and Computer Engineering Publications

Deep level transient spectroscopy was used to investigate the thermal stability of electron traps in n-type GaN grown by metalorganic chemical vapor deposition. The concentration of traps at 160 and at 500K increased more than fivefold over the course of several 700Kanneal cycles, while a peak at 320K increased by a factor of only 1.19. The increase in the trap concentration with repeated annealing might be due to a mobile trap or loss of passivant. Hydrogen is very likely present in high concentration in the epilayer, and its passivating effects may be lost with annealing.

Studies Of Ingan∕Gan Multiquantum-Well Green-Light-Emitting Diodes Grown By Metalorganic Chemical Vapor Deposition, K. S. Ramaiah, Y. K. Su, S. J. Chang, C. H. Chen, F. S. Juang, H. P. Liu, I. G. Chen

Electrical and Computer Engineering Publications

InGaN(3nm)∕GaN(5nm) three period multiquantum green-light-emitting diodes(LEDs) grown by the metalorganic chemical vapor deposition technique have been studied using high-resolution transmission electron microscopy (HRTEM), double crystal high resolution x-ray diffraction (HRXRD) and low temperature photoluminescence. HRTEM analysis showed that the defect density gradually decreased in the growth direction with increasing thickness. Self-assembled quantum dot-likestructures in the wells and black lumps between the well and barrier due to In segregation and strain contrast were observed, respectively. The HRXRD spectrum of the green LEDstructure was simulated using the kinematical theory method to obtain the composition and thickness of the well and barrier. The …

Reexamination Of Some Spintronic Field-Effect Device Concepts, S. Bandyopadhyay, M. Cahay

Electrical and Computer Engineering Publications

Current interest in spintronics is largely motivated by a belief that spin-based devices (e.g., spin field-effect transistors) will be faster and consume less power than their electronic counterparts. Here we show that this is generally untrue. Unless materials with extremely strong spin-orbit interaction can be developed, the spintronic devices will not measure up to their electronic cousins. We also show that some recently proposed modifications of the original spin field-effect transistor concept of Datta and Das [Appl. Phys. Lett.56, 665 (1990)] actually lead to worse performance than the original construct.

The Effect Of Hydrogen Etching On 6h-Sic Studied By Temperature-Dependent Current-Voltage And Atomic Force Microscopy, S. Doğan, D. Johnstone, F. Yun, S. Sabuktagin, J. Leach, A. A. Baski, Hadis Morkoç, G. Li, B. Ganguly

Electrical and Computer Engineering Publications

6H–SiC was etched with hydrogen at temperatures between 1000 and 1450°C. The etchedSi-terminated face for the 6H‐SiC wafer was investigated by atomic force microscopy and temperature-dependent current–voltage (I–V–T)measurements. Mechanical polishing damage was effectively removed by hydrogen etching at temperatures above 1250°C. Atomic force microscopy images revealed that very good surface morphology, atomic layer flatness, and large and large step width were achieved. Schottky diode characteristics were investigated in detail by current–voltage and temperature-dependent current–voltage measurements, and the results showed a transition from defect assisted tunneling to thermionic emission as the annealingtemperature was increased from 1250 to 1450°C.

Stimulated Emission And Time-Resolved Photoluminescence In Rf-Sputtered Zno Thin Films, Ü. Özgür, A. Teke, C. Liu, S.-J. Cho, Hadis Morkoç, H. O. Everitt

Electrical and Computer Engineering Publications

Stimulated emission (SE) was measured from ZnOthin filmsgrown on c-plane sapphire by rf sputtering. Free exciton transitions were clearly observed at 10 K in the photoluminescence(PL), transmission, and reflection spectra of the sample annealed at 950 °C. SE resulting from both exciton-exciton scattering and electron hole plasma formation was observed in the annealed samples at moderate excitation energy densities. The SE threshold energy density decreased with increasing annealing temperature up to ∼950 °C. The observation of low threshold exciton-exciton scattering-induced SE showed that excitonic laser action could be obtained in rf-sputtered ZnOthin films. At excitation densities below the SE threshold, …

Investigation Of Forward And Reverse Current Conduction In Gan Films By Conductive Atomic Force Microscopy, J. Spradlin, S. Doǧan, J. Xie, R. Molnar, A. A. Baski, Hadis Morkoç

Electrical and Computer Engineering Publications

We have used conductive atomic force microscopy (C–AFM) to investigate the forward and reverse bias current conduction of homo- and heteroepitaxial GaN-based films grown by molecular beam epitaxy. In the case of homoepitaxy, C–AFM shows enhanced current conduction at the centers of ∼30% of spiral hillocks, which are associated with screw dislocations. Local current–voltage spectra taken by C–AFM on and off such hillocks indicate Frenkel–Poole and field emission mechanisms, respectively, for low current levels in forward conduction. In the case of heteroepitaxialGaN films grown on sapphire, the correlation between conduction pathways and topography is more complex. We do observe, however, …

Effects Of Hydrostatic And Uniaxial Stress On The Schottky Barrier Heights Of Ga-Polarity And N-Polarity N-Gan, Y. Liu, M. Z. Kauser, M. I. Nathan, P. P. Ruden, S. Dogan, Hadis Morkoç, S. S. Park, K. Y. Lee

Electrical and Computer Engineering Publications

We report measurements of the Schottky barrier heights of Ni/Au contacts on Ga-polarity and N-polarity n-GaN under hydrostatic pressure and applied in-plane uniaxial stress. Under hydrostatic pressure the two different polarities of GaN yield significantly different rates of Schottky barrier height increase with increasing pressure. Uniaxial stress parallel to the surface affects the Schottky barrier height only minimally. The observed changes in barrier height under stress are attributed to a combination of band structure and piezoelectric effects.