Mechanical Engineering Commons^™

Conductive Polymer Blends And Their Use In Memory Devices, Mohammad Yousef Al-Haik

Theses

The aim of this project is to synthesize and characterize conductive polymers made out of blending nonconductive polymers with ionic liquids. An application to demonstrate the use of these novel conductive polymers is to create an organic memory device.

Attempts to synthesize conductive polymers have been reported in the literature; several of these approaches include doping a polymer with arsenic or iodine based dopant. In this work, ionic liquids, known as plasticizer, are sued as the dopant for non-conductive polymers. There are several advantages of employing the ionic liquids over other dopants, including the maintenance of organic based blends (both …

Evaluation Of Novel High-Density Emg Feedback Parameters On The Spatial Distribution Of Trapezius Muscle Activity, Brecca M. Gaffney

Electronic Theses and Dissertations

Each year, 17.9% of adults working in a computer-dominated work environment develop an episode of chronic neck and shoulder pain. An effective treatment method for chronic pain is postural correction through therapist. The understanding of the relation between cervicoscapular posture and trapezius muscle activity is not fully understood because the anatomy of the scapula is not accessible for direct observation. Until recently, the spatial distribution of trapezius muscle activity could not be measured due to the limitation in size of detection zone in traditional bipolar electrodes. The primary goal of postural correction when treating cases of chronic neck and shoulder …

Compressive Response Of Polycrystalline Nicomnga High-Temperature Meta-Magnetic Shape Memory Alloys, H. E. Karaca, A. S. Turabi, B. Basaran, A. K. Pathak, I. Dubenko, N. Ali, Y. I. Chumlyakov, P. Li

Mechanical Engineering Faculty Publications

The effects of the addition of quaternary element, Co, to polycrystalline NiMnGa alloys on their magnetic and shape memory properties have been investigated. NiCoMnGa polycrystalline alloys have been found to demonstrate good shape memory and superelasticity behavior under compression at temperatures greater than 100 °C with about 3% transformation strain and low-temperature hysteresis. It is also possible to train the material to demonstrate a large two-way shape memory effect.

Fluid-Structure Interactions With Flexible And Rigid Bodies, David J. Daily

Theses and Dissertations

Fluid structure interactions occur to some extent in nearly every type of fluid flow. Understanding how structures interact with fluids and visa-versa is of vital importance in many engineering applications. The purpose of this research is to explore how fluids interact with flexible and rigid structures. A computational model was used to model the fluid structure interactions of vibrating synthetic vocal folds. The model simulated the coupling of the fluid and solid domains using a fluid-structure interface boundary condition. The fluid domain used a slightly compressible flow solver to allow for the possibility of acoustic coupling with the subglottal geometry …

Performance Of Solid Oxide Iron-Air Battery Operated At 550°C, Xuan Zhao, Yunhui Gong, Xue Li, Nansheng Xu, Kevin Huang

Faculty Publications

“Metal-air” batteries have garnered much attention in recent years due to their high intrinsic specific energy and use of inexhaustible and storage-free oxygen source -air- for the “metal-oxygen” reaction. In this study, we report theperformance of a new type of all solid-state “iron-air” battery operated at 550°C. The results show that CeO₂ nanoparticles incorporated into the Fe-Fe₃O₄ redox-couple can improve the specific energy (Wh/kg) and round trip efficiency by 15% and 29%, respectively, over the baseline Fe-Fe₃O₄ battery. Use of supported Fe-Fe₃O₄ nanoparticles as the redox couple can increase the …

A Multiobjective Optimization Method For Collaborative Products With Application To Engineering-Based Poverty Alleviation, Nicholas Scott Wasley

Theses and Dissertations

Collaborative products are created by combining components from two or more products to result in a new product that performs previously unattainable tasks. The resulting reduction in cost, weight, and size of a set of products needed to perform a set of functions makes collaborative products useful in the developing world. In this thesis, multiobjective optimization is used to design a set of products for optimal individual and collaborative performance. This is introduced through a nine step method which simultaneously optimizes multiple products both individually and collaboratively. The method searches through multiple complex design spaces while dealing with various trade-offs …

Micro Modeling Study Of Cathode/Electrolyte Interfacial Stresses For Solid Oxide Fuel Cells, Xinfang Jin, Xingjian Xue

Faculty Publications

Delamination of the cathode/electrolyte interface is an important degradation phenomenon in solid oxide fuel cells (SOFCs). While the thermal stress has been widely recognized as one of the major reasons for such delamination failures, the role of chemical stress does not receive too much attention. In this paper, a micro-model is developed to study the cathode/electrolyte interfacial stresses, coupling oxygen ion transport process with structural mechanics. Results indicate that the distributions of chemical stress are very complicated at the cathode/electrolyte interface and show different patterns from those of thermal stress. The maximum principal stresses take place at the cathode/electrolyte interface …

Studies On Structure And Property Of Polymer-Based Nano-Composite Materials, Yun Zhai

LSU New Orleans Theses and Dissertations

The mixing of polymers and nanoparticles makes it possible to give advantageous macroscopic material performance by tailoring the microstructure of composites. In this thesis, five combinations of nano inclusion and polymer matrix have been investigated.

The first type of composites is titanium dioxide/ polyaniline combination. The effects of 4 different doping-acids on the microstructure, morphology, thermal stability and thermoelectric properties were discussed, showing that the sample with HCl and sulfosalicylic dual acids gave a better thermoelectric property. The second combination is titanium dioxide/polystyrene composite. Avrami equation was used to investigate the crystallization process. The best fit of the mass derivative …

A Mathematical Model For Quantifying System Evolvability Using Excess And Modularity, Morgan Wesley Parry Tackett

Theses and Dissertations

An important factor in system longevity is service-phase evolvability, which is defined as the ability of a system to physically transform from one configuration to a more desirable configuration while in service. These transformations may or may not be known during the design process, and may or may not be reversible. A study of 210 engineered systems was performed and found that system excess and modularity allow a system to evolve while in service. Building on these observations, this thesis introduces mathematical relationships that map a system's excess and modularity to that system's ability to evolve. These relationships are derived …

Using Topology Optimization To Numerically Improve Barriers To Reverse Engineering, Devin Donald Lebaron

Theses and Dissertations

Here explored is a method by which designers can use the tool of topology optimization to numerically improve barriers to reverse engineering. Recently developed metrics, which characterize the time (T) to reverse engineer a product, enable this optimization. A key parameter use din the calculation of T is information content (K). The method presented in this thesis pursues traditional topology optimization objectives while simultaneously maximizing K, and thus T, in the resulting topology. This thesis presents new algorithms to 1) evaluate K for any topology, 2)increase K for a topology by manipulating macro-scale geometry and micro-scale crystallographic information for each …

Micro-Jet Cooling Of Cutting Tools, Douglas J. Woodruff, Gary W. Pannala, William J. Endres, Nicole Barna, Quincy Schultz, David Thomasini, Matthew Zblewski

Michigan Tech Patents

A cutting tool includes an insert defining a flank face, a rake face, and a cutting edge between the flank face and rake face. The cutting tool includes micro-nozzles formed in at least one of the tool body and the insert, and aimed at the cutting edge. Each micro-nozzle generates a micro jet of cutting fluid in close proximity to the cutting edge and adjacent to at least one of the flank face and the rake face.

Floating Electrode Electrowetting On Hydrophobic Dielectric With An Sio2 Layer, Mehdi Khodayari, Benjamin Hahne, Nathan B. Crane, Alex A. Volinsky

Faculty Publications

Floating electrode electrowetting is caused by dc voltage applied to a liquid droplet on the Cytop surface, without electrical connection to the substrate. The effect is caused by the charge separation in the floating electrode. A highly-resistive thermally-grown SiO2 layer underneath the Cytop enables the droplet to hold charges without leakage, which is the key contribution. Electrowetting with an SiO2 layer shows a memory effect, where the wetting angle stays the same after the auxiliary electrode is removed from the droplet in both conventional and floating electrode electrowetting. Floating electrode electrowetting provides an alternative configuration for developing advanced electrowetting-based devices.

An Exploration Of Carbon-Filled Carbon Nanotubes As A Potential Material In Coronary Stents, Kristopher Neil Jones

Theses and Dissertations

The purpose of this research is to explore the potential of using carbon-infiltrated carbon nanotubes (CI-CNT) as a material for coronary artery stents. Stents are commonly fabricated from metal, which may not perform as well as many polymers and ceramics in biomedical applications. Pyrolytic carbon, a ceramic, is currently used in medical implant devices due to its preferrable biocompatibility properties. Micro-patterned pyrolytic carbon devices can be created by growing carbon nanotubes, and then filling the space between with amorphous carbon via chemical vapor deposition. We prepared multiple samples of two different planar stent-like flexible geometries and smaller cubic structures out …

College Of Engineering Senior Design Competition Spring 2013, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Senior Design Experience

Part of every UNLV engineering student's academic experience, the Senior Design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs and prototypes a product in this required element of the curriculum. Working in teams, the senior design project encourages students to use everything learned in the engineering and computer design programs to create a practical, real world solution to an engineering challenge.

Beyond the classroom ...

Because of the requirement to work in teams, students also build good communication skills, presentation skills and even business writing skills. They also have to …

Heterogeneous Relaxation Dynamics In Amorphous Materials Under Cyclic Loading, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

Molecular dynamics simulations are performed to investigate heterogeneous dynamics in amorphous glassy materials under oscillatory shear strain. We consider three-dimensional binary Lennard-Jones mixture well below the glass transition temperature. The structural relaxation and dynamical heterogeneity are quantified by means of the self-overlap order parameter and the dynamic susceptibility. We found that at sufficiently small strain amplitudes, the mean square displacement exhibits a broad subdiffusive plateau and the system undergoes nearly reversible deformation over about 104 cycles. Upon increasing strain amplitude, the transition to the diffusive regime occurs at shorter time intervals and the relaxation process involves intermittent bursts of large …

Monte Carlo Uncertainty Analysis For Photothermal Radiometry Measurements Using A Curve Fit Process, Kyle Horne, Austin Fleming, Heng Ban

Utah Space Grant Consortium

Photothermal Radiometry (PTR) has become a popular method to measure thermal properties of layered materials. Much research has been done to determine the capabilities of PTR, but with little uncertainty analysis. This study performs a Monte Carlo uncertainty analysis to quantify uncertainty of film diffusivity and effusivity measurements, presents a sensitivity study for each input parameter, compares linear and logarithmic spacing of data points on frequency scans, and investigates the validity of a 1-D heat transfer assumption.

Assessment Of An Automotive Driving Simulator To Educate Novice Drivers, John Wagner, Qimin Yao, Kim Alexander, Philip Pidgeon

Publications

Novice drivers are more likely to be involved in vehicle crashes than more experienced drivers. Transportation system simulators, such as aerospace, automotive, and rail, have been used effectively over several decades in support of operator training and research studies. The immersive high-end automotive simulators tend to be large-scale, difficult to move, and relatively cost ineffective for widespread deployment. In contrast, a mobile vehicle training system often features simplistic environments which are not readily accepted by teenagers who evaluate the driving experience as compared to commercial video games. Consequently, a need exists for a low-cost portable automotive training system that provides …

Focused Novice Driver Program - Assessment Results And Discussion, John Wagner, Lance Clark, Kim Alexander, Philip Pidgeon, Ken Rogich

Publications

Skills and experiences of novice drivers do not favorably compare to motorists with significantly greater driving time and life experiences. Recent developments in driver education and training have focused on multistage instruction to take advantage of the time delay for driving privileges in Graduated Driver Licensing (GDL) systems as a means to provide additional instruction. A supplemental safe driving program tailored to address the risky behaviors of novice drivers has been developed by Clemson University Automotive Safety Research Institute (CU-ASRI) and the Richard Petty Driving Experience (RPDE). The program offers training in anticipatory safe driving strategies based on the leading …

Design And Construction Of An Experiment For The Investigation Of The Effects Of Gust On Flapping Wing Micro Air Vehicle Power Consumption, Brett Hiller

Mechanical Engineering Undergraduate Honors Theses

In recent years, the promising nature of flapping wing flight has led researchers to investigate the wing morphology and unsteady wing aerodynamics found in insects to aid in the design of modern micro air vehicles (MAVs). A high-fidelity flapping wing MAV could achieve high mobility, hovering stability, increased stealth, and efficient flight at low speeds. These characteristics offer a viable solution to the operational requirements for the typical hazardous and dynamic environments encountered during flight. While the kinematics and morphology of flapping wings are well-understood, significant research has yet to be completed with respect to the control and power requirements …

Optimization Of Automated Temperature Measurement System For Formed Meat Products, Tyler Norman

Mechanical Engineering Undergraduate Honors Theses

The Federal Safety and Inspection Services in accordance with United States Department of Agriculture require that formed meat products be cooked to a specified minimum internal temperature in order to eliminate the possible presence of harmful bacteria. The current system of verifying the internal temperatures of formed meat products consists of manually inserting a temperature probe into the selected sample as it exits the oven. Creating an automated system that measures and records the internal temperatures of formed meat samples as they exit the oven along a meat processing line has been the topic of an ongoing research. The most …