Mechanical Engineering Commons^™

Finite-Size Effects On Molecular Dynamics Interfacial Thermal-Resistance Predictions, Zhi Liang, Pawel Keblinski

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using Molecular Dynamics Simulations, We Study the Role of Finite Size Effects on the Determination of Interfacial Thermal Resistance between Two Solids Characterized by High Phonon Mean Free Paths. in Particular, We Will Show that a Direct, Heat Source-Sink Method Leads to Strong Size Effect, Associated with Ballistic Phonon Transport to and From, and Specular Reflections at the Simulation Domain Boundary. Lack of Proper Account for These Effects Can Lead to Incorrect Predictions About the Role of Interfacial Bonding and Structure on Interfacial Thermal Resistance. We Also Show that the Finite Size Effect Can Be Dramatically Reduced by Introduction of …

Geometric Solution In Progressive Collapse Analysis Of Hull Girder, Ertekin Bayraktarkatal, Gökhan Tansel Tayyar

Journal of Marine Science and Technology–Taiwan

This paper presents a calculation model for stiffened plates to determine the ultimate strength of ship hull girders from their curvatures using a geometrical approach. The present study employed Smith’s method, in which the cross-section is divided into smaller elements consisting of a stiffener(s) and attached plating. The strength of beam-columns and stiffened plates was obtained using an iterative numerical approach. The deflection curve was evaluated using the curvature values directly instead of by solving differential equations. The deflection curve was taken as an assembly of chains of circular arcs. The ultimate strength of the hull girder of a 1/3 …

Evaluation Of The Performance Of Various Turbulence Models For Accurate Numerical Simulation Of A 2d Slot Nozzle Ejector, Colin Graham

McKelvey School of Engineering Graduate Student Theses & Dissertations

With the development over the last several decades, accurate Computational Fluid Dynamics (CFD) modeling has now become an essential part in the analysis and design of various industrial products where the fluid flow plays an important role. The goal of this thesis is to apply the CFD technology to the analysis of a 2D slot nozzle ejector which has application in Short Take-off and Landing (STOL) aircraft and other future aerospace vehicles. In the nozzle-ejector configuration, the high speed air flow from the nozzle entrains the ambient air into a mixing chamber (ejector) as a means to create additional thrust …

Three Dimensional Transient Asymmetric Flowfields In Physical Vapor Transport, Joseph Dobmeier

Journal of Undergraduate Research at Minnesota State University, Mankato

Physical Vapor Transport is a manufacturing process used to produce single crystals of semiconductor materials such as mercurous chloride (Hg2Cl2). In the past this time-varying process has been studied with numerical simulation by considering three dimensional flow using an axi-symmetric two dimensional model or by restricting the simulation to asymmetric two dimensional flow and dropping the assumption of axi-symmetry from the model. It is generally agreed that neither of these methods accurately represent the true behavior of the process. The purpose of this research was to extend the asymmetric two dimensional model to three dimensions thereby obtaining a solution which …

Therapeutic Potential Of Haptic Theradrive: An Affordable Robot/Computer System For Motivating Stroke Rehabilitation, Andrew Theriualt, Mark L. Nagurka, Michelle J. Johnson

Mechanical Engineering Faculty Research and Publications

There is a need for increased opportunities for effective neurorehabilitation services for stroke survivors outside the hospital environment. Efforts to develop low-cost robot/computer therapy solutions able to be deployed in home and community rehabilitation settings have been growing. Our long-term goal is to develop a very low-cost system for stroke rehabilitation that can use commercial gaming technology and support rehabilitation with stroke survivors at all functioning levels. This paper reports the results of experiments comparing the old and new TheraDrive systems in terms of ability to assist/resist subjects and the root-mean-square (RMS) trajectory tracking error. Data demonstrate that the new …

Implementing Dubins Airplane Paths On Fixed-Wing Uavs, Timothy Mclain, Randall W. Beard, Mark Owen

Faculty Publications

A well-known path-planning technique for mobile robots or planar aerial vehicles is to use Dubins paths, which are minimum-distance paths between two configurations subject to the constraints of the Dubins car model. An extension of this method to a three-dimensional Dubins airplane model has recently been proposed. This chapter builds on that work showing a complete architecture for implementing Dubins airplane paths on small fixed-wing UAVs. The existing Dubins airplane model is modified to be more consistent with the kinematics of a fixed-wing aircraft. The chapter then shows how a recently proposed vector-field method can be used to design a …

Ultrasonics Transduction In Metallic And Composite Structures For Structural Health Monitoring Using Extensional And Shear Horizontal Piezoelectric Wafer Active Sensors, Ayman Kamal Abdelrahman

Theses and Dissertations

Structural health monitoring (SHM) is crucial for monitoring structures performance, detecting the initiation of flaws and damages, and predicting structural life span. The dissertation emphasizes on developing analytical and numerical models for ultrasonics transduction between piezoelectric wafer active sensors (PWAS), and metallic and composite structures.

The first objective of this research is studying the power and energy transduction between PWAS and structure for the aim of optimizing guided waves mode tuning and PWAS electromechanical (E/M) impedance for power-efficient SHM systems. Analytical models for power and energy were developed based on exact Lamb wave solution with application on multimodal Lamb wave …

Oxygen Flux And Dielectric Response Study Of Mixed Ionic-Electronic Conducting (Miec) Heterogeneous Functional Materials, Fazle Rabbi

Theses and Dissertations

Dense mixed ionic-electronic conducting (MIEC) membranes consisting of ionic conductive perovskite-type and/or fluorite-type oxides and high electronic conductive spinel type oxides, at elevated temperature can play a useful role in a number of energy conversion related systems including the solid oxide fuel cell (SOFC), oxygen separation and permeation membranes, partial oxidization membrane reactors for natural gas processing, high temperature electrolysis cells, and others. This study will investigate the impact of different heterogeneous characteristics of dual phase ionic and electronic conductive oxygen separation membranes on their transport mechanisms, in an attempt to develop a foundation for the rational design of such …

Investigation Of Thermal Performance Of Nanoparticle Enhanced Ionic Liquids (Neils) For Solar Collector Applications, Titan Chandra Paul

Theses and Dissertations

Concentrated Solar Power (CSP) is a prominent alternative energy technology, where mirrors or lenses are used to concentrate sunlight from a large area and stored in a collector filled with heat transfer fluid (HTF). The energy from this HTF is used to produce steam for power generation. CSP system requires high heat storage capacity and thermally stable HTF to reduce its operating cost. Having suitable thermophysical properties, ionic liquids (ILs) is considered as a potential HTF for the CSP applications; however thermophysical properties of ILs can be further enhanced by dispersing small volume percentages of nanoparticles. This liquid is called …

Plant-Biomimetic Hydrogel Actuators: Creating Movement In Hydrogels Through The Study Of Plants, Christen Rhodes

Theses and Dissertations

Plants are sessile organisms that have developed methods of movement to respond to environmental stimuli. Some of the approaches feature the unequal expansion of cells and controlling deformation direction through fibers under swelling and drying. Hydrogels are three dimensional polymer networks that have the capacity for large volume changes due their affinity for water and can be tough and/or stimuli-responsive. In this paper, three preliminary plant-biomimetic hydrogel actuator designs are discussed and tested from wet to dry. The first actuator design, termed a 1%-0.1% bilayer, features two layers of different swelling and drying rates due to differences in cross-linking density. …

Structural Health Monitoring Using Linear And Nonlinear Ultrasonic Guided Waves, Yanfeng Shen

Theses and Dissertations

The dissertation addresses Structural Health Monitoring (SHM) using linear and nonlinear ultrasonic guided waves, with an emphasis on the development of analytical and numerical models of guided wave propagation and interaction with linear and nonlinear structural damage.

An analytical model was developed based on the exact Lamb wave solution for the simulation of Lamb wave propagation and interaction with damage. The damage effects were inserted into the model using complex valued wave damage interaction coefficients (WDICs). The analytical procedure was coded as a framework into a MATLAB Graphical User Interface (GUI), and the software WaveFormRevealer (WFR) was developed as a …

Dielectric Properties Of Composite Materials During Damage Accumulation And Fracture, Md. Rassel Raihan

Theses and Dissertations

Fiber reinforced polymer matrix composite materials have many unique properties and their high performance makes them available to use in many advanced technologies i.e. aerospace, microelectronics, and energy storage. There is a correlation that exists between the long term behavior of those materials under combined mechanical, thermal, and electrical fields, and the functional properties and characteristics of the composite materials that requires a fundamental understanding of the material state changes caused by deformation and damage accumulation. This will ultimately lead, for example, to the design and synthesis of optimal multifunctional material systems. Composite materials are heterogeneous and the complex morphology …

Thermal Analysis Of High Pressure Micro Plasma Discharge, Mostafa Mobli

Theses and Dissertations

High pressure micro plasma discharge has been at the center of interest in recent years, because of their vast applications, ease of access and cost efficiency. This attributes to atmospheric discharges that are generated in ambient conditions and therefore can be readily applicable to everyday use. The absence of vacuum makes these high pressure discharges to be inexpensive to operate. Despite the ease of operation, the high pressure is a source of enhanced gas heating as the gas temperature cannot be controlled by diffusion alone. Gas heating is therefore an important factor when it comes to the simulation of high …

Thermal Transport Across A Substrate-Thin-Film Interface: Effects Of Film Thickness And Surface Roughness, Zhi Liang, Kiran Sasikumar, Pawel Keblinski

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using Molecular Dynamics Simulations and a Model AlN-GaN Interface, We Demonstrate that the Interfacial Thermal Resistance RK (Kapitza Resistance) between a Substrate and Thin Film Depends on the Thickness of the Film and the Film Surface Roughness When the Phonon Mean Free Path is Larger Than Film Thickness. in Particular, When the Film (External) Surface is Atomistically Smooth, Phonons Transmitted from the Substrate Can Travel Ballistically in the Thin Film, Be Scattered Specularly at the Surface, and Return to the Substrate Without Energy Transfer. If the External Surface Scatters Phonons Diffusely, Which is Characteristic of Rough Surfaces, RK is Independent …

Performance And Durability Of Electrodes With Platinum Catalysts In Polymer Electrolyte Cells Prepared By Ultrasonic Spray Deposition, William A. Rigdon

Theses and Dissertations

Catalysts in the electrodes of polymer electrolyte cells serve a critical function in reactions which can be used to either generate electrical energy from chemical fuels or convert electrical energy into chemicals. For low temperature electrochemical fuel cells, platinum is often utilized for its exceptional catalytic activities towards hydrogen oxidation and oxygen reduction reactions of the anode and cathode, respectively. However, the limited supply of platinum and high demand result in prohibitive costs plaguing commercialization of this technology. Therefore, minimal amounts of the catalyst should be used to achieve the maximum output to reduce expenses. Electrochemical behavior is governed by …

Granular Matter: Microstructural Evolution And Mechanical Response, Aashish Ghimire, Ishan Srivastava, Timothy S. Fisher

The Summer Undergraduate Research Fellowship (SURF) Symposium

Heterogeneous (nano) composites, manufactured by the densification of variously sized grains, represent an important and ubiquitous class of technologically relevant materials. Typical grain sizes in such materials range from macroscopic to a few nanometers. The morphology exhibited by such disordered materials is complex and intricately connected with its thermal and electrical transport properties. It is important to quantify the geometric features of these materials and simulate the fabrication process. Additionally, granular materials exhibit complex structural and mechanical properties that crucially govern their reliability during industrial use. In this work, we simulate the densification of soft deformable grains from a low-density …

Visualizing Mechanics: Educational Videos Demonstrating Core Mechanics Concepts, Camilo Schrader, Jeffrey Rhoads, Charles M. Krousgrill, Stephen Alex Stamm, Elizabeth Bushman

The Summer Undergraduate Research Fellowship (SURF) Symposium

There has been an increased interest in using technology to relay information over the past 20 years. This interest has been reflected in the way the internet has expanded to incorporate nearly-uncountable numbers of blogs, streaming videos, and discussion forums. Recent research has shown that younger generations of students prefer internet-based platforms such as these to communicate and learn, as they are congruent with a visual style of learning. The present study seeks to fuse the predominantly reflective and intuitive methods found in a traditional lecture with the more visual and active modes of learning to provide a larger range …

Porphyrin Interaction With Dna-Based Carbon Nanotubes And Regeneration For Light Harvesting, Sawyer E. Morgan, Hanyu Zhang, Jong Hyun Choi

The Summer Undergraduate Research Fellowship (SURF) Symposium

Limitations to current solar cells include the high cost of pure silicon and poor current transfer within cells. An emerging alternative is single-walled carbon nanotubes (SWCNTs), which when combined with DNA and porphyrin chromophores can generate a current when absorbing light. We sought to find a chromophore and conditions that would promote bonding to the SWCNTs and improve light harvesting, while being able to regenerate on the film after being damaged. This was experimentally tested by first making SWCNT films on conducting glass slides. These were then functionalized in solutions of chromophore and spectra were measured to determine the bonding …

Design Of A Small Scale Roll To Roll Device, Amon A. Pereira, Edward White, Rebecca Krone Kramer

The Summer Undergraduate Research Fellowship (SURF) Symposium

In the soft robotics field, hyperelastic polymer films are used in conjunction with eutectic gallium indium to create flexible strain gages. However, rapid large scale manufacturing methods of such sensors have yet to be developed.

Developing new manufacturing methods will allow for researchers to build and test new soft sensor concepts faster but also pave the way for future mass-production of these sensors for consumer or industrial consumption.

One of those methods would be a Roll to Roll System (R2R) similar to those used to in the publication industry. In this context, Polyethylene terephthalate (PET) film rolls will be used …

Development Of Integration Software For Multiple Inkjet Functionalization Systems, Jieyu Lu, J. William Boley, George T.-C. Chiu

The Summer Undergraduate Research Fellowship (SURF) Symposium

Inkjet printing is widely used in functional product manufacturing. Performing a printing task requires communication and synchronization among multiple subsystems (e.g. motion and drop ejection), which introduces complexity in the overall printing system. A user interface has been developed, which enables users to input printing parameters and patterns for printing functional materials. The interface then sends commands to the controllers that execute the printing process. The software can also be expanded to carry out standard experiments for functional printing research and characterization. Moreover, the software is transferable to multiple systems. One application explored using the software is drug anti- counterfeiting …