Mechanical Engineering Commons^™

Groundwater Quality Analyses For Irrigation Purposes In Salah Al-Din, Iraq: A Review, Noor A. Radhi, Dawood E. Sachit, Abdul-Sahib T. Al-Madhhachi

Al-Esraa University College Journal for Engineering Sciences

The focus of this study is the effect of the physical and chemical characteristics of groundwaters on plants and agricultural crops, following the last studies on this matter. The results underscore the necessity for groundwater treatment before its utilization in irrigation for sustainable agricultural farming. It is also possible to identify which crop type can be grown in well-watered land, according to the characteristics of irrigation water and the yield of each crop. The study also introduces some ideas about irrigation water quality parameters such as Electrical conductivity (EC), Total Dissolved Solids (TDS), pH, Chloride (Cl^–), Sodium (Na …

Examining Iot-Enhanced For Current Developments In Face Image Authentication (Fia) Methods And Their Drawbacks, Marwa Jamal Hadi, Emaan Ouudha Oraby

Al-Esraa University College Journal for Engineering Sciences

The quick development of IoT and facial image manipulation (FIM) algorithms, as well as the growth of their user-friendly applications, highlight the pressing need for manipulation detection methods. These techniques need to demonstrate how face photos have been altered and validate their legitimacy. The scientific community has recently taken notice of the phrase “DeepFakes” and methods for detecting them. Take note of the latest methods for identifying watermark-based face image modification as well. The important thing to remember is that every one of these methods has its own set of drawbacks. This study provides a brief introduction to face image …

Analyzing Wearable Sensor Data From Individuals Undergoing Motor And Neurological Rehabilitation, Carly Smith

College of Engineering Summer Undergraduate Research Program

An ongoing study funded by the National Science Foundation (NSF) is focused on developing computational models of rehabilitation for people post-stroke. Stroke affects around 800,000 people per year in the US, and often leaves people with limited motor (movement) and neurological (brain-based) capability. Wearable sensors may allow clinicians to better understand how these individuals recover, and to better design therapies and interventions. We are seeking students who can use existing software, and perhaps adapt the software to extract, analyze, and visualize detail from study participants. This project will involve with the Cal Poly PI, and collaborators from physical therapy. This …

Human-Ai Collaboration For Creative Design, Antony Chen

College of Engineering Summer Undergraduate Research Program

Design-by-Analogy (DbA) is a powerful design tool that uses analogical reasoning to help engineers develop groundbreaking innovations, such as cyclonic separator inspired bagless vacuum cleaner or gecko inspired adhesives. DbA leverages the natural, human process of analogical reasoning in a systematic manner in three phases namely: retrieval (what prior knowledge/experience is relevant to a design problem?), mapping (what elements of the design problem align with the retrieved knowledge?), and evaluation (how applicable is the retrieved knowledge to solving a design problem?). To date, most DbA techniques support one or two phases of analogical reasoning and therefore overlook important opportunities for …

Motor Subsystem For A Tensegrity-Based Robotic Exoskeleton, Presley Sacavitch, Israel Villegas

College of Engineering Summer Undergraduate Research Program

Tensegrity structures are composed of stiff rods and elastic cables suspended in a flexible tension network. In particular, the biotensegrity model proposes that all biological systems exhibit tensegrity-like characteristics across multiple scales, ranging from the cellular level to the musculoskeletal system of tendons, ligaments, and fascia, to the human body as a whole. Compared to the traditional biomechanical models used in exoskeleton design, it can be a more accurate representation of how motion emerges from natural forms, but further work is needed to fully understand the heterarchical nature of human anatomy. This project will focus on developing a powered electrical …

Impulse, Fall 2025, Jill Fier, Sierra Brown, Jerome J. Lohr College Of Engineering

Impulse (Jerome J. Lohr College of Engineering Publication)

2 | Faculty News
3 | SDSU Vet Hua to Head Civil Engineering
6 | Ad Lunam — To the Moon
10 | Building A Safety Culture
11 | Department News
12 | Surface Mount Technology Kickoff
14 | Construction Management Student, Volleyball Player Building Success Piece by Piece
16 | Student Awards, Honors
18 | Student Competition Results
20 | NASA Win Opens Doors for New Product Development Order
22 | SDSU Engineering Student Tabbed as Noblereach Fellow
26 | Knabach Award Recipient from Apprentice Lineman to Company President
28 | Metzger Create Faculty Endowment for SDSU Engineering
30 …

Advances In Encapsulated Phase Change Materials For Integration In Thermal Management Applications, Muhammad Ghufran, David Huitink

Mechanical Engineering Faculty Publications and Presentations

Encapsulated phase change materials (ePCMs) have the potential to emerge as a key solution for efficient thermal management in various applications. This review paper explores the recent advancements in ePCMs for thermal energy storage and thermal management. We start with a basic overview of the PCMs and then performance enhancements of PCMs through the encapsulation, critical parameters for encapsulation, various encapsulation methods, and their evaluation are discussed. This review also discusses key properties and proposed figure of merit for ePCMs, impact of encapsulation on thermophysical properties, performance evaluation of ePCMs, thermal management needs, and the role of PCMs. The paper …

Characterization Of The Fatigue Threshold Behavior Of Uhmwpe, Bethany B. Smith, Anurag Roy, Robert O. Ritchie, Lisa A. Pruitt

Faculty Journal Articles

Ultra-high-molecular-weight-polyethylene (UHMWPE) has been the material of choice for bearings in total joint replacements (TJRs) for decades as a result of its excellent wear resistance, chemical inertness, energetic toughness, low friction, and biocompatibility. Utilization of this polymer in orthopedic devices requires oxidation, wear, and fatigue resistance. Balancing these important properties by tailoring processing techniques and modulating microstructural features has been an ongoing endeavor in the field. Research into the clinical applications of UHMWPE has primarily focused on the challenges of wear and oxidation while studies into the realm of fatigue have been more limited. Literature gaps exist in fully understanding …

Design Of Ballistic Armor Using Multi-Composite Sandwich Structures With Nanomaterial Additives, Carmen Alaichamy

College of Engineering Summer Undergraduate Research Program

This study explores the bulletproof capabilities of Kevlar composites fabricated using advanced additive manufacturing techniques. Continuous fiber reinforced 3D printing (CFRP) is employed to produce Kevlar-reinforced polymer matrix composites (PMCs) with optimized structural configurations for ballistic protection. The primary objective is to evaluate the impact resistance of these composites against 9mm projectiles through systematic experimental testing. A series of ballistics tests are conducted using a high-velocity gas-gun system to fire 9mm projectiles at varying speeds angles. The tests will be conducted at the San Luis Obispo Range, with projectiles fired at various angles. The effects of fiber volume fraction, reinforcement …

Cold Spray On Fiber Reinforced Polymer Substrates For Composite Repair And Tooling Applications, Patrick Allen Bailey

Theses and Dissertations

Cold Spray technology was first developed in the 1980’s and is an additive manufacturing and repair technique. It works by heating a pressurized carrier gas upwards of 600 °C and inserting metal particles downstream such that when they impact a substrate, the energy transformation causes plastic deformation of the particles. This thesis presents a use case for metal and polymer CS powder on fiber reinforced and fused filament fabrication polymer substrates. The state of the art for CS discusses the most up-to-date research within the field, and where new investigations are required. This research investigates the required process parameters to …

Analyzing Wearable Sensor Data From Individuals Undergoing Motor And Neurological Rehabilitation, Nolan William Turk

College of Engineering Summer Undergraduate Research Program

An ongoing study funded by the National Science Foundation (NSF) is focused on developing computational models of rehabilitation for people post-stroke. Stroke affects around 800,000 people per year in the US, and often leaves people with limited motor (movement) and neurological (brain-based) capability. Wearable sensors may allow clinicians to better understand how these individuals recover, and to better design therapies and interventions. We are seeking students who can use existing software, and perhaps adapt the software to extract, analyze, and visualize detail from study participants. This project will involve with the Cal Poly PI, and collaborators from physical therapy. This …

A Biomimetic Fe Model Of The Human Foot For Kinematic And Footwear Analysis, Brady K. Nakamura

College of Engineering Summer Undergraduate Research Program

The idea of the present proposal is to develop a biomimetic foot model and validate the model accuracy in predicting plantar stresses on the foot, using insole pressure sensors. The incidences of foot pain can often be coupled with uncomfortable footwear and prolonged usage of a shoe may be associated with long-term musculoskeletal disorders in the lower limb. While multiple studies have tracked the progression of knee osteoarthritis (OA) or midfoot OA and have studied the effect of orthotic treatment on the foot pain across individuals [1], there are few biomimetic models of the foot that can study and associate …

Light-Activated Self-Folding Of Polystyrene-Based Shape Memory Polymers: A Comparison Of Laser Induced Graphene And Marker Patterns, Amelia Lodwick

College of Engineering Summer Undergraduate Research Program

Shape memory polymers (SMPs) are a class of stimuli-responsive materials capable of undergoing programmable shape transformations upon thermal activation. Among various heating methods, light-induced activation provides a contact-free, spatially selective, and controllable approach for triggering self-folding behavior, making it particularly valuable for applications in soft robotics, aerospace structures, and biomedical devices. Despite the growing interest in SMPs, a systematic investigation into the influence of photothermal patterning materials, light intensity, and heat distribution on self-folding behavior remains limited. This research aims to explore the self-folding response of a commercially available SMP by employing photothermal materials such as carbon black and laser-induced …

Evaluating The Effectiveness Of Ultrasound-Hot Plate And Flacktek Mixing In Nanocomposite Panel Fabrication, Jacky Liang, Wyatt Barnes

College of Engineering Summer Undergraduate Research Program

Nanomaterials have found widespread applications, particularly carbon nanotubes (CNTs) in structural applications, which have gained significant traction over the past few decades [1] [2]. Numerous experimental [3] [4] [5] [6] [7] [8] [9] [10] and analytical studies [11] have demonstrated that incorporating CNTs into an epoxy matrix can significantly enhance the mechanical properties of the composite. This study evaluates and compares the effectiveness of nanocomposite panels fabricated using two different fabrication techniques: ultra-sonication combined with a hot plate process, and the FlackTek mixer. The primary objective of the research is to investigate the impact of these processing methods on the …

Leveraging Smartphones For Balance Assessment, Kelly Graham

College of Engineering Summer Undergraduate Research Program

Assessment of human balance provides valuable metrics to track the health, development, and fall risk of individuals. The prominent method for objective balance assessments has used force plates to track the center of pressure (COP) position as a participant attempts to balance during varying tasks. However, the use of force plates is limited by the cost of equipment and expertise required, leading to recent interest in using embedded inertial measurement units (IMUs) in mobile devices instead. Many researchers have explored placing mobile devices close to the subject’s center of mass (COM) to approximate the subject’s COM acceleration and using the …

Certifiably Robust Input-Dependent Randomized Smoothing Via Lipschitz Standard Deviation Networks, Faith Bergstrom, Ben Sager

College of Engineering Summer Undergraduate Research Program

Modern artificial intelligence (AI) systems exhibit highly sensitive and unsafe behavior when subjected to undetectable cyberattacks. For instance, human-imperceptible manipulations of the pixels in image data can cause traffic sign classifiers to mispredict stop signs as yield signs. In this project, we will design and analyze new methods to robustify machine learning (ML) models against these adversarial threats. Specifically, we will explore randomization techniques that "smooth out" the ML model's decision making process by intentionally corrupting input data with small amounts of noise. Optimizing this noise to enhance resilience against attacks while maintaining the system's accuracy poses a major open …

Augmented Biomechanics Integration For Real-Time Movement Optimization, Jack Bergfeld, Liyen Ho, Dylan Featherson

College of Engineering Summer Undergraduate Research Program

This project aims to integrate OpenCap, a markerless motion capture system, with augmented reality (AR) to optimize real-time human movement. By leveraging biomechanics principles, AR visualization, and machine learning (ML), the system will provide instant feedback to users, improving movement efficiency while minimizing joint and muscle stress. Previous research in 2024-2025 has successfully demonstrated 2D motion tracking and AR-based mapping onto another person for interactive comparison. This project will build upon that foundation by enhancing real-time 3D motion tracking and developing an advanced AR interface to guide users in sports training, rehabilitation, and workplace ergonomics. The integration of ML will …

Exploration Of Physics-Informed Grid Generation Technique For Wall-Modeled Les Using Eagle3d, Dominic Schneider

Doctoral Dissertations and Master's Theses

Wall-Modeled Large Eddy Simulation (WMLES) is an area of interest due to its ability to lower computational costs of LES. Even with the application of wall models, LES still proves to have practicality issues when it comes to use in industry, due to the expertise, time, and computational resources required. A novel technique for generating a lean, physics based WMLES grid is described.

The technique utilizes a RANS solution to extract turbulence information, user-specified values related to resolution of turbulent energy levels, acoustics waves, and shock waves, to generate a point cloud for producing a lean WMLES grid with in-house …

Active Measurement Of A Micron-Order Gap Under High-Speed And High-Temperature Conditions, Andrew Becker

Doctoral Dissertations and Master's Theses

The hypersonic regime poses numerous challenges that researchers face in the development of hypersonic flight vehicles. Due to their excellent thermomechanical properties, ultra-high-temperature ceramics (UHTCs) have risen as a promising solution to act as a protective barrier between the harsh environment and surface materials of these flight bodies. The mechanical operation of a portable hypersonic simulation device was developed in-house and tested at Argonne National Laboratories (ANL) to gather in-situ material response of prospective UHTC samples when exposed to a hypersonic regime. An edge detection-based algorithm was developed and used in LabVIEW to monitor the health and operation of the …

Compost Grinder For The University Of South Carolina Office Of Sustainability, Rori E. Pumphrey, Grace Yaegel, Aaron R. Sawyer, Bradley White

Senior Theses

This project originates from a collaboration with the USC Office of Sustainability, which seeks to improve the handling and processing of food waste generated on campus. The primary challenge is the difficulty in composting certain types of food waste, such as avocado pits, pumpkin rinds, and other dense or fibrous organic materials that are not easily broken down using conventional methods. Existing commercial solutions are often too large and expensive, or electrically powered, and are thus not well suited for the volume or nature of USC's food waste. To address these limitations, our team designed a manually operated food waste …