Mechanical Engineering Commons^™

Investigating The Fatigue Behavior Of Inconel 939 And Inconel 718 Through Micromechanical Testing, Mohammad Hossein Shahini

LSU Doctoral Dissertations

A detailed evaluation of fatigue crack growth (FCG) in a silicon-modified Inconel 939 alloy, fabricated via laser powder bed fusion additive manufacturing (L-PBF AM), was performed using cyclic bending tests on pre-notched microscale cantilevers with a cross-sectional dimension of 25 µm × 25 µm. To our knowledge, this study is the first to demonstrate that such microscale cantilever tests can effectively capture both the threshold and Paris-law regimes of FCG, despite the limited specimen size. The precise fabrication of these small-scale specimens allows for controlled fatigue crack propagation relative to the microstructure while minimizing the presence of volumetric defects. Notably, …

Recreating Fiber Recruitment With Fiber Recruitment Using Additive Manufacturing, Natalia D. Mciver

Biomedical Engineering ETDs

Injured ligaments are often repaired with tendon grafts which may over or under constrain the joint; there is a need for an artificial graft option with the mechanical properties of a native ligament. Crimped fibers within ligaments allow for recruitment which means the viscoelastic properties of stress relaxation and creep are not inversely related. A feasibility study using ACLs and large-scale crimp models to study viscoelasticity, led to an in-depth analysis of the scapholunate interosseous ligament. Using the Modified Kelvin spring-dashpot model, for describing viscoelasticity with a variable stiffness property (time dependent fiber recruitment), we defined the relationship between creep …

Graph Based Planning With Guarantees, Trazon Tyrik Jimerson

Mechanical Engineering ETDs

This thesis presents two graph-based methods with formal guarantees for motion planning and routing. First, the invariant-set motion planner (ISMP), which uses constraint admissible positive invariant (CAPI) sets of closed-loop dynamics, is adapted for spacecraft attitude planning to avoid moving keep-out zones. Contributions include time bounds for maneuvers via exponential stability, a single-stage reachability graph from one-step backward reachable CAPI sets, and its multi-stage expansion to certify node safety over time. Simulations verify safe attitude control with moving obstacles. Second, we formulate a convex optimization problem over a network for evacuation planning with operational constraints such as helicopter capacity and …

Simulation Of Stress Induced By Laser Heating Of Glass, Austin Marsh Schuberth

Mechanical Engineering ETDs

The purpose of this work is to create a method for accurately simulating the stresses due to heating from femtosecond laser pulses. Our work aims to calculate stress and strain in glass exposed to laser pulses used for laser welding. We simulate the effects of thermal heating, thermal expansion, and the viscoelasticity of glass for a single straight weld bead. The laser heating of K9 borosilicate glass was simulated using Finite Element Analysis (FEA). Thermal models developed by other researchers in earlier work were utilized in calculating the temperatures due to the laser exposure to the glass material. 2D simulations …

Real-Time Frequency Tuning Of Kinetic Energy Harvesters Via System Mass Adjustment, Rahul Adhikari

Mechanical Engineering ETDs

This research presents a method for real-time frequency tuning of piezoelectric kinetic energy harvesters through system-mass adjustment. Custom 3D-printed proof masses with cavity arrays were used to redistribute solid or liquid mass, enabling controlled modification of resonant frequency. Experimental studies using microparticles and liquids—including water, silicone oil, and sodium polytungstate—demonstrated an achievable tuning range of 115.27 Hz with sub-hertz resolution (< 0.1 Hz), confirming precise and repeatable frequency control. Finite-element modeling guided design optimization, while a microfluidic channel system enabled automated liquid filling for real-time operation. A MATLAB-based EH_Tuning application was developed to visualize and predict frequency responses. The combined …

Design And Development Of Evacuated Photovoltaic-Thermal Systems For Efficient Cogeneration Of Heat And Electricity, Behnam Roshanzadeh

Mechanical Engineering ETDs

In conventional PV systems, most of the solar energy is dissipated into the environment as heat. Accordingly, hybrid Photovoltaic-thermal systems have been developed to utilize the waste heat from PV cells for various thermal applications. However, most PVT systems suffer from low thermal performance compared to solar thermal collectors, as the absorber plate in PVT systems is partially or fully covered by PV cells. This dissertation focuses on improving the thermal performance of PVT systems by introducing the evacuated PVT systems.

An evacuated-tube PVT system was designed and simulated for domestic hot water supply. The evacuated-tube PVT system demonstrated 40% …

Labram Ii Power Equation And Application To Model A Powder System, Layton Bertrand Bahnmiller

Graduate Theses & Non-Theses

This thesis validates equations that predict power input with machine data for the LabRAM II resonant acoustic mixer (RAM), an industrial tool for mixing powders used in advanced manufacturing and other applications. While RAM offers unique advantages such as gentle mixing and adaptability for sensitive or heterogeneous blends, the manufacturer’s power equation lacked published experimental validation. To address this gap, a custom constantvolume calorimeter was designed to directly measure the energy imparted during RAM operation under controlled conditions. Finite element analysis and analytical heat transfer models ensured calorimeter assumptions were valid. Calorimetric experiments revealed that the vendor’s power input equation …

Integrated Experimental, Numerical, And Machine-Learning Framework For The Analysis Of Spray Dynamics In Diesel And Gasoline Direct-Injection (Gdi) Engines, Yassine El Marnissi

Theses and Dissertations

The regulation of diesel and gasoline direct injection (GDI) during cold starts has become subject to stricter numerical limits by both the Environmental Protection Agency (EPA) in the US and the European Commission (EC). For diesel engines, the EPA’s Clean Trucks Plan (Model Year 2027+) sets a certification NOₓ limit of 0.035 g/bhp-hr and an in-use fleet average limit of 0.050 g/bhp-hr, along with a PM limit of 0.005 g/bhp-hr, representing an 82.5% reduction in NOₓ compared to the former 0.2 g/bhp-hr standard. For gasoline engines, US standards regulate cold-start pollutants such as hydrocarbons (HC) ranging from 0.03 to 0.08 …

Electrospun Nanofiber Creation With Varying Polymer-Solvent Combinations For Air Filtration, Lancaster Jace Hill

Theses and Dissertations

This study aims to analyze various polymer-solvent combinations for electrospun creation of nanofiber media and to determine the best-suited solution for lab-grade electrospinning. Suitable solutions allow for controlled morphology of fiber diameters and for efficiency of media creation. The principal variables are solvent, concentration, and voltage. Humidity and temperature play a secondary variable role. The solution must withstand an electric field of ≤30 kV and be insoluble in water to maintain desired morphology and structure. Manipulation of the solutions and variables allow for fiber diameter optimization and beading minimization. High temperature filter applications require efficiency in intense heat and preservation …

Novel Experimental Techniques For Pressure Transients, Luliang Zhang

Theses and Dissertations

This dissertation introduces novel experimental techniques for analyzing pressure transients, focusing on dynamic strain and pressure measurements to advance the understanding and application of Pulse Pressure Amplification in percussive devices. The research evaluates a high-speed linescan extensometer utilizing linescan Digital Image Correlation (DIC) on a Kolsky Bar to obtain strain data at high strain rates. This data is critical for accurate material characterization and simulations to model dynamic behavior. Additionally, a novel method for measuring dynamic pressure waves in pipe systems has been developed, enabling direct assessments of pressure amplification in devices such as tapered pipe systems. The findings contribute …

Concerted Rattling-Induced Strong Anharmonicity And Phonon Coherence Lead To Ultralow Glasslike Thermal Conductivity In Tlagte, Shantanu Semwal, Yi Xia, Chris Wolverton, Koushik Pal

Mechanical and Materials Engineering Faculty Publications and Presentations

Ordered crystalline compounds exhibiting ultralow and glass-like thermal conductivity are both fundamentally and technologically important, where phonon quasi-particles dominate their heat transport. Understanding the microscopic mechanisms that govern such unusual transport behavior is necessary to unravel the complex interplay of crystal structure, phonons, and collective excitations of these quasi-particles. Here, we use state-of-the-art first-principles calculations based on quantum density functional theory to investigate the origin of experimentally measured unusually low and glassy thermal conductivity in semiconducting TlAgTe that possesses disconnected chains of Tl atoms within its three-dimensional crystalline framework made up of distorted AgTe4 tetrahedra. Utilizing a unifying framework of …

Investigation Of The Flow Field Morphology Of Film Cooling In Supersonic Flow, Umberto Sandri, Massimiliano Ferro, Alessio Picchi, Antonio Andreini, Bruno Facchini, Marc D. Polanka

Faculty Publications

Film cooling is widely implemented in highly thermally stressed gas turbine components. Its performance has been extensively investigated for several decades and many results are available in the literature. In conventional gas turbines, regions of supersonic flow are not prevalent and should generally be avoided. For this reason, results relative to film cooling in supersonic flow are limited. Nevertheless, a new interest related to Rotating Detonation Combustors (RDC) and supersonic turbines is growing. The implementation of those engine components in a gas turbine is likely to need film cooling for thermal protection. In this context, it becomes crucial to gain …

Dynamic Urban Air Mobility Systems Modeling And Simulation, Amer M. Ibrahim

Tennessee State University Alumni Theses and Dissertations

The use of electrical vertical takeoff and landing (eVTOL) aircraft to provide efficient, high-speed, on-demand air transportation within a metropolitan area is an increasingly popular topic, which is expected to bring fundamental changes to cities. The concept of Urban Air Mobility (UAM) has the potential to make meaningful door-to-door trip time savings compared with other transportation. The capability to manage many of these eVTOL aircraft safely in a congested urban area presents an unprecedented challenge in air traffic management. In order to enable safe and efficient autonomous on-demand free flight operations in UAM, a computational guidance algorithm with collision avoidance …

Influence Of Build Plate Location On Tensile Properties And Residual Stresses In Lpbf-Fabricated Stainless Steel 316 Components, Yareli Zelaya Pavón

Honors Program Theses and Research Projects

Additive manufacturing (AM), particularly Laser Powder Bed Fusion (LPBF), enables rapid production of complex metal components with minimal waste. Stainless Steel 316 (SS316) is widely used in engineering applications due to its corrosion resistance and mechanical reliability. This study investigates the influence of build plate location on tensile properties and residual stresses in LPBF-fabricated SS316. Twelve tensile specimens and nine unsupported bridge structures were fabricated at different build plate positions using a “machine model.” Tensile testing provided stress-strain data to evaluate peak stress, elastic modulus, and strain at break, while bridge curvature measurements quantified residual stress through warping. Results indicate …

Advancing Sustainable Co2 Mitigation: Experimental And Computational Analysis Of Thermal Carbon Chitosan Sorbent For Automotive Exhaust Capture, Dalia A. Ali Dr., Amir Ahmed Elgamal Eng., Rania Rushdy Moussa Dr.

Chemical Engineering

This study investigated the efficiency of thermal carbon chitosan (TCCS) sorbent for CO2 capture from vehicle exhaust emissions within a designed adsorption system. TCCS was synthesized and meticulously characterized using a series of analytical techniques, including Brunauer-Emmett-Teller (BET) surface area analysis, Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), Ther- mogravimetric Analysis (TGA), Energy Dispersive X-ray Spectroscopy (EDX), and Differential Scanning Calo- rimetry (DSC). The TCCS adsorbent showed high thermal stability and a heating value (HHV) of 23.5 MJ/kg. Adsorption isotherm study demonstrated that the maximum capacity of CO2 adsorption is 0.084 kg.CO2/kg. TCCS, as well …

Development And Validation Of 2nn-Meam Interatomic Potential For Sc And Al-Sc Alloys Thermodynamics Solidification And Intermetallic Ordering, Avik Mahata

Mechanical Engineering Faculty Publications

We present a second-nearest-neighbor Modified Embedded Atom Method (2NN–MEAM) potential for Scandium (Sc) and Aluminum-Scandium (Al–Sc) alloys that unifies cohesive, thermodynamic, and solidification behavior within a single transferable framework. The Sc component accurately reproduces cohesive energy, lattice constants, defect energetics, and the experimental melting point obtained from two-phase coexistence, demonstrating reliable description of both hcp and liquid phases. The Al–Sc binary interaction parameters were fitted using the L1₂–Al₃Sc reference and benchmarked against first-principles and calorimetric data. The potential reproduces the strong negative formation enthalpy of Al₃Sc (–0.45 eV atom⁻¹), correct relative stability …

Tunable Phase-Change Metasurfaces Coupled With Mid-Infrared Molecular Vibrations, Haotian Tang, Liliana Stan, David A. Czaplewski, Xiaodong Yang, Jie Gao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Chiral optical meta surfaces have emerged as a promising platform in coupling with molecular vibrational fingerprints through the enhanced light-matter interaction under different circularly polarized light illumination. This work reports the mode coupling between the mid-infrared phonon vibrations of polymethyl methacrylate (PMMA) molecules, and the thermally tunable chiral meta surfaces based on the phase-change material Ge₂Sb₂Te₅ (GST-225). Phase-change chiral meta surfaces with high circular dichroism (CD) in absorption and tunable plasmonic resonance in the frequency range of 48-56 THz are demonstrated, which covers the phonon vibrational frequency of PMMA molecules at 52 THz. The mode splitting features are observed in …

Advancing Radiation Shielding For Human Space Exploration, Bryan Trejo, Lea Scott, Eduardo Farfan

Symposium of Student Scholars

Beyond the safety of the Earth's magnetic field, out into the treacherous reaches of space, lies a harsh environment of radiation. This study examines radiation shielding strategies for crewed spacecraft operating in various environments, including Mars transit and deep space. Within these environments, ionizing radiation remains a critical challenge to long-duration, crewed space travel. Galactic Cosmic Rays (GCR), high-energy protons and heavy nuclei originating outside our solar system, as well as Solar Particle Events (SPE), highly energetic protons ejected continuously during the 11-year solar cycle, are all analyzed in their unique interactions with spacecraft material and biological tissues. Shielding to …

A Review Of Waste Heat Sources For District Heating, Olamide Opadokun, Yong Tao, Julian Lamb

Mechanical Engineering Faculty Publications

As the world's energy needs rise, carbon emissions and climate change become a bigger concern. Therefore, there is a growing need for cleaner energy sources as well as higher levels of energy efficiency. Building energy is of great interest to researchers and policymakers, as it accounts for about a third of global energy consumption, and this is projected to rise as more people gain access to higher incomes and improved amenities. For over a century, district energy systems have proved to be an efficient means of providing thermal energy to buildings, and developments in district heating have enabled the use …

Thermal Heterogeneity And Lithium Plating During Fast Charging Of Lithium-Ion Battery., Ayodeji Avis Adeniran

Electronic Theses and Dissertations

Presently, widespread adoption of electric vehicles (EVs) is hindered by challenges associated with XFC, including heat generation, lithium plating, and accelerated battery degradation. This dissertation addresses these barriers through two coordinated themes—lithium plating and thermal management—spanning four manuscripts that integrate operando diagnostics, physics-based simulation, and module-level design optimization. The first theme seeks a fundamental investigation into the dynamic interplay between temperature heterogeneity and lithium plating during fast charging, a phenomenon that poses significant limitations on the performance of graphite-based anodes. Firstly, a custom operando cell with a sapphire window was designed to enable synchronized MWIR thermography and optical imaging of …