Mechanical Engineering Commons^™

A Virtual Supply Airflow Rate Meter In Rooftop Air Conditioning Units, Daihong Yu

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

Virtual sensing technology aims to estimate difficult to measure, expensive, or new quantities by using multifarious mathematical models along with non-invasive and low-cost measurements. Such embedded intelligence is a key to improving the performance of building systems in terms of functionality, safety, energy efficiency, environmental impacts, and costs. Considering the progress that has been achieved over many various fields (e.g., process controls, automobiles, avionics, autonomous robots, telemedicine) within the last two decades, numerous intelligent features have been incorporated and enabled that would otherwise not be possible or economical.

To identify the potential opportunities and research/development needs of virtual sensing technology …

Nanostructured Substrate With Nanoparticles Fabricated By Femtosecond Laser For Surface-Enhanced Raman Scattering, Yukun Han, Zhi Liang, Huilai Sun, Hai Xiao, Hai-Lung Tsai

Electrical and Computer Engineering Faculty Research & Creative Works

A Simple and Fast Method to Fabricate Nanostructured Substrates with Silver Nanoparticles over a Large Area for Surface-Enhanced Raman Scattering (SERS) is Reported. the Method Involves Two Steps: (1) Dip the Substrate into a Silver Nitrate Solution for a Few Minutes, Remove the Substrate from the Solution, and Then Air Dry and (2) Process the Silver Nitrate Coated Substrate by Femtosecond (Fs) Laser Pulses in Air. the Second Step Can Create Silver Nanoparticles Distributed on the Nanostructured Surface of the Substrate by the Photoreduction of Fs Multiphoton Effects. This Study Demonstrates that an Enhancement Factor (EF) Greater Than 5x105, Measured …

Fracture Analysis Of Kevlar-49/Epoxy And E-Glass/Epoxy Doublers For Reinforcement Of Cracked Aluminum Plates, Ananth Ram Mahanth Kasavajhala, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Adhesively bonded composite patch repair is an efficient means to regain load carrying capacity, alleviate the crack growth, and improve the service life of the damaged structure. In this paper, three dimensional finite element models are developed to ex­amine the fracture behavior of a single edge V-notched Aluminum plate repaired with Kevlar-49/epoxy or e-glass/epoxy pre-preg patches on both sides. Contour integral method was used for evaluating the stress intensity factor (SIF), an indicator of the crack stability. The load transfer mechanisms, stress distribution, damage variable (D), and crack mouth opening displacement (CMOD), were also presented to estimate the …

A Differential Planetary Gear Model With Backlash And Teeth Damage, Xi Wu, Jim Meagher, Andrew Sommer

Mechanical Engineering

Planetary gear trains can be more compact and efficient as power transmissions than fixed axis gear trains but are also more complicated and less understood in terms of vibration health monitoring. A practical differential planetary gear train, which combines two inputs and one output, is studied using multi-body dynamics software. Backlash between the sun gear and planet gears are precisely specified to avoid teeth interference and undercut. In order to calculate accurate impact forces, an impact model is chosen. Tooth geometry errors are created on the sun gear. Constraints and contact forces to the model are applied as close as …

An Advanced Numerical Model Of Gear Tooth Loading From Backlash And Profile Errors, Andrew Sommer, Jim Meagher, Xi Wu

Mechanical Engineering

This study demonstrates the early transient dynamic loading on teeth within a fixed-axis gear transmission arising from backlash and geometric manufacturing errors by utilizing a non-linear multi-body dynamics software model. Selection of the non-linear contact parameters such as the stiffness, force exponent, damping, and friction coefficients are presented for a practical transmission. Backlash between gear teeth which is essential to provide better lubrication on tooth surfaces and to eliminate interference is included as a defect and a necessary part of transmission design. Torsional vibration is shown to cause teeth separation and double-sided impacts in unloaded and lightly loaded gearing drives. …

Estimating The Yield Strength Of Thin Metal Films Through Elastic-Plastic Buckling-Induced Debonding, S Goyal, K Srinivasan, G Subbarayan, Thomas Siegmund

School of Mechanical Engineering Faculty Publications

In this paper, we propose a procedure to estimate the yield strength of thin films by debonding films from their substrate by elastic-plastic buckling under thermally-induced compressive loading. The out-of-plane displacement of the metal lines under conditions of elastic-plastic buckling is dependent on the yield strength of the film. Thus, an inverse estimate of the yield strength is made from measurements of the out-of-plane displacements of the buckled metal lines. The procedure is demonstrated to estimate the yield strength of aluminum lines consistent with measurements by other techniques.

Design And Fabrication Of A Tapped Densification Apparatus For Bulk Solids, Joshua H. De Jong

Theses

Experiments are commonly used to ascertain the flow properties of bulk solids. One such property is a measurement quantity known as the tapped density. Here, a container of granular material is subjected to a long sequence of discrete taps, after which the bulk density - the total mass divided by the volume occupied –- is determined. Current technology exists to achieve the maximum tap density by subjecting a container to a user defined number of taps at a specific, predetermined amplitude and frequency. However, the final bulk density is known to be dependent on the tap parameters. It can therefore …

Characterising 3d Soft Tissue Features On Joint Surfaces, Colm O'Kane

Conference Papers

A crucial aspect of orthopaedic implant design is the prediction of surgical outcomes when the shape of a bone is necessarily altered by the addition of the implant. Matching native kinematics as closely as possible is generally considered a core aim of joint replacement surgery. The overall hypothesis behind this research is that soft tissue geometry, including cartilage thickness distribution and ligament attachment sites, influences kinematics in the knee joint. In order to enable investigation of possible links between geometry and kinematics, the ability to characterise the shape variation of the soft tissue relative to the underlying bony geometry must …

A 3-D Chain Algorithm With Pseudo-Rigid-Body Model Elements, Robert Parley Chase, Robert H. Todd, Larry L. Howell, Spencer P. Magleby

Faculty Publications

A chain algorithm element is created from pseudo-rigid-body segments and used in a chain calculation that accurately predicts the force deflection relationship of beams with large 3-D deflections. Each chain element is made up of three pseudo-rigid-body models superimposed on each other acting orthogonally in relation to each other. The chain algorithm can predict large displacements and the force-deflection relationship of lateral torsional buckled beams significantly faster than the finite element method. This approach is not intended to compete with finite element analysis, but rather is a supplement tool that may prove particularly useful in the early phases of design …

Intelligibility Of Electrolarynx Speech Using A Novel Hands-Free Actuator, Brian Madden, Mark Nolan, Ted Burke, James Condron, Eugene Coyle

Conference Papers

During voiced speech, the larynx provides quasi-periodic acoustic excitation of the vocal tract. In most electrolarynxes, mechanical vibrations are produced by a linear electromechanical actuator, the armature of which percusses against a metal or plastic plate at a frequency within the range of glottal excitation. In this paper, the intelligibility of speech produced using a novel hands-free actuator is compared to speech produced using a conventional electrolarynx. Two able-bodied speakers (one male, one female) performed a closed response test containing 28 monosyllabic words, once using a conventional electrolarynx and a second time using the novel design. The resulting audio recordings …

Short-Term Curtailment Of Hvac Loads - Executive Summary, Florida Solar Energy Center, Lixing Gu

FSEC Energy Research Center®

Rapidly increasing requirements placed on utilities to reduce peak loads has led to utility customer incentives to shift peak demand to non-peak times or reduce peak loads when notified by the utility that the grid is close to capacity. This study investigates methods used to reduce building demand during a fixed time window near a utilities on-peak period. The window was chosen to be 5-9 A.M. in winter and 2-5 P.M. in summer. The most common methods for reducing building peak demand were reviewed and categorized by their usefulness and wide-spread availability. These strategies were reductions in lighting power density, …

Investigation Of Dc Motors For Electric And Hybrid Electric Motor Vehicle Applications Using An Infinitely Variable Transmission, Benjamin Carson Groen

Theses and Dissertations

Since the early 1900's demand for fuel efficient vehicles has motivated the development of electric and hybrid electric vehicles. Unfortunately, some components used in these vehicles are expensive and complex. AC motors, complex electronic controllers and complex battery management systems are currently used in electric (EV) and hybrid vehicles. This research examines various motors and speed control methods in an attempt to help designers identify which motors would be best suited for an EV powertrain application. The feasibility of using DC motors coupled with an Infinitely Variable Transmission (IVT), to obtain an innovative new electric or hybrid electric powertrain is …

Arra Advanced Weatherization Training Center - Quarterly Report (September 2010-December 2010), Florida Solar Energy Center, Neil Moyer

FSEC Energy Research Center®

The 4th quarter of 2010 was the initialization of the contract with DOE. During this time period, there were two major events that occurred. First, representatives from UCF-FSEC attended the three day Atlanta Weatherization Training Center Grantee Training Workshop with DOE representatives and the various organizations that were awarded funding. Secondly, the project management plan (PMP) was finalized and submitted to the Project Manager.

A Full-Depth Amalgamated Parallel 3d Geometric Multigrid Solver For Gpu Clusters, Dana A. Jacobsen, Inanc Senocak

Mechanical and Biomedical Engineering Faculty Publications and Presentations

Numerical computations of incompressible flow equations with pressure-based algorithms necessitate the solution of an elliptic Poisson equation, for which multigrid methods are known to be very efficient. In our previous work we presented a dual-level (MPI-CUDA) parallel implementation of the Navier-Stokes equations to simulate buoyancy-driven incompressible fluid flows on GPU clusters with simple iterative methods while focusing on the scalability of the overall solver. In the present study we describe the implementation and performance of a multigrid method to solve the pressure Poisson equation within our MPI-CUDA parallel incompressible flow solver. Various design decisions and algorithmic choices for multigrid methods …

Scalability Of Incompressible Flow Computations On Multi-Gpu Clusters Using Dual-Level And Tri-Level Parallelism, Dana A. Jacobsen, Inanc Senocak

Mechanical and Biomedical Engineering Faculty Publications and Presentations

High performance computing using graphics processing units (GPUs) is gaining popularity in the scientific computing field, with many large compute clusters being augmented with multiple GPUs in each node. We investigate hybrid tri-level (MPI-OpenMP-CUDA) parallel implementations to explore the efficiency and scalability of incompressible flow computations on GPU clusters up to 128 GPUS. This work details some of the unique issues faced when merging fine-grain parallelism on the GPU using CUDA with coarse-grain parallelism using OpenMP for intra-node and MPI for inter-node communication. Comparisons between the tri-level MPI-OpenMP-CUDA and dual-level MPI-CUDA implementations are shown using computationally large computational fluid dynamics …

Robust Region Tracking In Multi-Agent Systems Utilizing Sliding Mode Control: Theory And Applications, Mark Bacon

Master's Theses

This thesis presents a methodology to bring controlled agents within a moving region despite agent interaction dynamics, uncertain forces and parameter variation. The logic is derived from traditional Sliding Mode Control theory with an expanded boundary layer which allows position deviation from the region center to specified bounds. As an example of the utility of this control, multiple methods of herding (controlling passive agents by appropriate positioning of controlled agents) are presented.

Orbits Design For Leo Space Based Solar Power Satellite System, Neelima Krishna Murthy Addanki

Dissertations, Master's Theses and Master's Reports - Open

Space Based Solar Power satellites use solar arrays to generate clean, green, and renewable electricity in space and transmit it to earth via microwave, radiowave or laser beams to corresponding receivers (ground stations). These traditionally are large structures orbiting around earth at the geo-synchronous altitude.

This thesis introduces a new architecture for a Space Based Solar Power satellite constellation. The proposed concept reduces the high cost involved in the construction of the space satellite and in the multiple launches to the geo-synchronous altitude. The proposed concept is a constellation of Low Earth Orbit satellites that are smaller in size than …

Effect Of High Order Interpolation In The Stability And Efficiency Of The Time-Integration Process In Vorticity-Velocity Cfd Algorithms, Pankaj A. Jagadale

Dissertations, Master's Theses and Master's Reports - Open

The numerical solution of the incompressible Navier-Stokes Equations offers an effective alternative to the experimental analysis of Fluid-Structure interaction i.e. dynamical coupling between a fluid and a solid which otherwise is very complex, time consuming and very expensive. To have a method which can accurately model these types of mechanical systems by numerical solutions becomes a great option, since these advantages are even more obvious when considering huge structures like bridges, high rise buildings, or even wind turbine blades with diameters as large as 200 meters. The modeling of such processes, however, involves complex multiphysics problems along with complex geometries. …

Muffler Characterization With Implementation Of The Finite Element Method And Experimental Techniques, Tyler W. Le Roy

Dissertations, Master's Theses and Master's Reports - Open

Determining how an exhaust system will perform acoustically before a prototype muffler is built can save the designer both a substantial amount of time and resources. In order to effectively use the simulation tools available it is important to understand what is the most effective tool for the intended purpose of analysis as well as how typical elements in an exhaust system affect muffler performance. An in-depth look at the available tools and their most beneficial uses are presented in this thesis. A full parametric study was conducted using the FEM method for typical muffler elements which was also correlated …

Comprehensive Review And Application Of Particle Image Velocimetry, Michael P. Norconk

Dissertations, Master's Theses and Master's Reports - Open

For a fluid dynamics experimental flow measurement technique, particle image velocimetry (PIV) provides significant advantages over other measurement techniques in its field. In contrast to temperature and pressure based probe measurements or other laser diagnostic techniques including laser Doppler velocimetry (LDV) and phase Doppler particle analysis (PDPA), PIV is unique due to its whole field measurement capability, non-intrusive nature, and ability to collect a vast amount of experimental data in a short time frame providing both quantitative and qualitative insight. These properties make PIV a desirable measurement technique for studies encompassing a broad range of fluid dynamics applications. However, as …