Mechanical Engineering Commons^™

Bucky Gel Actuator For Morphing Applications, Ali Kadkhoda Ghamsari

LSU Doctoral Dissertations

Since the demonstration of Bucky Gel Actuator (BGA) in 2005, a great deal of effort has been exerted to develop novel applications for electro-active morphing materials. Three-layered bimorph nanocomposite has become an excellent candidate for morphing applications since it can be easily fabricated, operated in air, and driven with few volts. There has been limited published study on the mechanical properties of BGA. In this study, the effect of three parameters: layer thickness, carbon nanotube type, and weight fraction of components, on the mechanical properties was investigated. Samples were characterized via nano-indentation and DMA. It was found that BGA composed …

Characterizing Impact Induced Hot-Spot Morphology In Granular Solid Explosive, John Gilbert

LSU Master's Theses

Deformation induced ignition of heterogeneous solid explosives is believed to originate at hot-spots within the material which are local regions of elevated temperature resulting from dissipative mechanisms such as plastic deformation and inter-particle friction. Inert meso-scale modeling of these materials can principally account for hot-spot formation enabling the characterization of hot-spot size and temperature distributions which are important for ignition but are di_x000E_cult to experimentally resolve. The focus of this study is to characterize hot-spot morphology, as well as the distribution of hot-spots, behind quasi-steady compaction waves computed from predicted temperature fields resulting from numerical simulations of rigid planar piston …

Energetic Nanoparticles As Fuel Additives For Enhanced Performance In Propulsion Systems, Srinibas Karmakar

LSU Doctoral Dissertations

Biofuels are currently being explored as a carbon-neutral fuel alternative to petroleum-based fuels. However, biofuels such as ethanol has lower energy density (~27MJ/kg) relative to petroleum fuels (~ 45 MJ/kg). Adding high-energy density particles (such as boron with heating value of ~ 58.5 MJ/kg) to biofuels can generate fuel slurry with higher energy density than the base fuel, and represents a potential strategy toward making biofuels more viable. However, the combustion of boron is inhibited (specifically, the ignition is delayed) by the initial presence of an oxide layer, and its high evaporation and boiling temperatures. The present study investigates the …

Advanced Ceramics And Composites Based On Rice Hulls, Peigen Zhang

LSU Doctoral Dissertations

As a by-product of the agricultural industry, rice hulls are available at large volume across the world. The disposal of the rice hulls itself is a big problem for the rice millers where the rice paddies are peeled off and rice hulls are produced. There have been many disposal methods developed, but the true value of the rice hulls would be more appreciated when they are employed to produce high value-added advanced ceramics. In this dissertation, advanced ceramics, such as AlN nanowires, SiC whiskers, mullite and SiC/Al2O3 nano-sized composites, were developed and studied based on the rice hulls. The SiC …

Towards The Development Of Biotin Carboxylase Driven Robotic Nanoswimmers, Rachel Yates

LSU Master's Theses

The objective of this research is to take the first step towards demonstrating the use of the enzyme biotin carboxylase (BC) as a biomolecular motor. BC is a homodimeric protein involved in fatty biosynthesis in all organisms. The conjecture is that BC can convert chemical energy into useful mechanical work via its conformation change, which acts as a fin or flexible oar producing nonreciprocal motion. To this end, we fabricate a proof-of-concept biomolecular machine driven by BC molecules, viz., a robotic nanoswimmer. This machine consists of a Janus-type nanosize silica particle, where one hemisphere is coated with an intermediate layer …

Novel Surface Modifications And New Nanostructured Titania Synthesis For High-Performance Lithium-Ion Batteries And Solar Cells, Dongsheng Guan

LSU Doctoral Dissertations

With the rapid development of electronic devices, electrical vehicles and space aerocrafts, rechargeable lithium-ion batteries (LIBs) have attract numerous interests due to high energy and power density, long lifespan and low self discharge. Spinel LiMn2O4 is a promising cathode material for novel LIBs thanks to high working potential, easy synthesis and low cost, but its severe capacity drop mostly due to inevitable reactions with electrolytes is a drawback. In the dissertation, ultrathin and highly-conformal Al2O3 coatings are grown on the surface of micro-sized and nanosized LiMn2O4 with atomic layer deposition. Thickness of Al2O3 ALD coatings can be precisely controlled by …

Pdms Based Waveguides For Microfluidics And Eocb, Weiping Qiu

LSU Master's Theses

Due to the low cost, fast and ease of molding, PDMS has become one of the most popular materials for microfluidics devices, bioMEMS applications. Meanwhile, the integration of different functional components on to one single chip (or Lab on a Chip) is the dream for many scientists and engineers in the related area. In addition to the necessary mechanical components for accommodating the reactions, such as pumps, valves, mixers and so on, optical components such as waveguides, lens, interferers are all desired to be lumped into such a system.

The waveguide for such a system requires the material to have …

Low-Order Modeling Of Micro-Flier Impact With Thin Stationary Energetic Targets, Mark B. Fry

LSU Master's Theses

The impact of high-speed (500-1500 m/s), laser driven micro-fliers with thin energetic targets (10-100 &# 956;m) is being examined to characterize impact-induced heating and combustion of these materials. Aluminum fliers are propelled by a laser into a thin metallic target plate having a layer of energetic material deposited on its backside. Mass spectrometry is performed in vacuo on the energetic side to interrogate the shock-induced chemistry of the energetic material. It is important to ignite and possibly detonate the energetic material without perforation of the target plate avoiding contamination of the vacuum chamber. To guide development of these experiments, a …

Programming And Healing Temperature Effects On The Efficiency Of Confined Self-Healing Polymers, Yves Quentin Yougoubare

LSU Master's Theses

Shape memory polymers are smart materials capable of fixing a temporary shape and returning to their initial shape in response to an external stimulus. Since the discovery and acknowledgment of their importance in 1960s, shape memory polymers have been the subject of tremendous and continuous attention. In a previous study conducted on a biomimetic shape memory polymer (SMP), the ability of a self-healing composite to heal, and to repair and restore structural-length scale damage using a close-then-heal (CTH) self-healing mechanism was examined and validated. The present study is purposed with investigation of the effects on healing efficiencies of the variation …

Flow Distribution And Heat Transfer Coefficients Inside Gas Holes Discharging, Amirhossein Eshtiaghi

LSU Master's Theses

Fluid flow and heat transfer coefficient associated with flow inside short holes (L/D=1) discharging orthogonally into a crossflow was investigated experimentally and numerically for (Re) ̅ ranging from 0.5×105 to 2×105, and blowing ratio ranging from 1.3 to 3.2. The basic configuration studied consists of a feed tube with five orthogonally located gas holes. Four different hole configurations were studied. The transient heat transfer study employs an IR-camera to determine the local heat transfer coefficient inside each hole. Velocity measurements and numerical flow simulation were used to better understand the measured heat transfer distribution inside the hole. The Nusselt number …

Optimal Actuation In Active Vibration Control Using Pole-Placement, Carla Ann Guzzardo

LSU Doctoral Dissertations

The purpose of this study was to find and demonstrate a method of optimal actuation in a mechanical system to control its vibration response. The overall aim is to develop an active vibration control method with a minimum control effort, allowing the smallest actuators and lowest control input. Mechanical systems were approximated by discrete masses connected with springs and dampers. Both numerical and analytical methods were used to determine the optimum force selection vector, or input vector, to accomplish the pole placement, finding the optimal location of actuators and their relative gain so that the control effort is minimized. The …

Turbine Blade Internal Cooling: Trailing Edge, Coolant-Passage Entry, Bend Effect And Improvement In Thermal Performance, Krishnendu Saha

LSU Doctoral Dissertations

Efficient cooling of gas turbine blade is imperative for safe operation of the gas turbine engine at high temperatures. In the present work, two converging lattice structures suitable for trailing edge applications are tested and their performance is compared with a conventional pin-fin configuration. Another constant cross section lattice structure is tested to see the cooling efficiency of lattice channels with different number of sub-channels. Converging lattice structures show higher heat transfer enhancement and comparable or higher thermal performance than traditional pin-fin cooling used in gas turbine trailing edge. The highest pressure drop incurred in a multi-pass channel is at …

Multifunctional Carbon/Epoxy Glass Microballons Nanocomposite, Ephraim Fentahun Zegeye

LSU Doctoral Dissertations

Glass microballoons have high strength, low thermal and electrical properties, and provide closed cell porosity to reduce the density of composites. On the other hand, filamentous carbon nanostructures have excellent mechanical, thermal, and electrical properties that make them naturally multifunctional. This work presents a method of developing low-density multifunctional nanocomposites utilizing glass microballoons and carbon nanostructures. Two different approaches are investigated. In the first approach, carbon nanotubes (CNTs) are used as a filler material to fabricate nanocomposites containing glass microballoons (CNT-syntactic foams). The weight percent of CNTs is varied from 0 to 0.8 wt%. In this method, CNTs were grown …

Multiscale Viscoplastic-Viscodamage Analysis Of Shape Memory Polymer Fibers With Application To Self Healing Smart Materials, Amir Shojaei

LSU Doctoral Dissertations

Self-healing smart material systems have been introduced into the research arena and they have already been deployed into industrial applications. The Close-Then-Heal (CTH) healing mechanism for polymeric self-healing systems is addressed herein and then a new generation of Shape Memory Polymer (SMP) based self-healing system is proposed in this work. This system incorporates SMP fibers to close the cracks while the embedded Thermoplastic Particles (TPs) are diffused into the crack surfaces upon heating and provide a molecular level of healing. The SMP fiber manufacturing procedure is briefly addressed in this work in which the bobbin of SMP fibers are heat …

Combinatorial Multi-Level Mold Inserts Using Micro Machining And X-Ray Lithography, Oblesh Jinka

LSU Master's Theses

The present technology advancement in biomedical, micro-electro-mechanical systems (MEMS) engineering, bio-MEMS, healthcare, etc. is driving the need to fabricate devices with multi-level, high aspect ratio and complex microstructures, which in turn requires high quality mold inserts with all these features. The present thesis is concentrated in fabricating a multi-level mold insert with complex quasi 3 dimensional micro structures with dimensions down to 10µm and aspect ratios greater than 30 using a process combination of micro milling with X-ray lithography. Therefore, in this study the main focus was to fabricate a high quality mold insert template, which can be electroplated to …

Stability Problems In Constrained Pendulum Systems And Time-Delayed Systems, Prashanth Ramachandran

LSU Doctoral Dissertations

In this dissertation, we study the boundary of stability of a class of linear mechanical systems as a function of a parameter. We consider two different systems under this class: a constrained double pendulum connected by a rigid rod and a state-feedback-controlled mechanical system with time delay. In the first system, the destabilizing parameter is the distance between the supports of the two pendulums. In the second system, the destabilizing parameter is the time delay. In the constrained double pendulum system, linear perturbation analysis is used to determine the natural frequency of the system. Our analysis reveals a zone of …

Dual Mode Sensing With Low-Profile Piezoelectric Thin Wafer Sensors For Steel Bridge Crack Detection And Diagnosis, Lingyu Yu, S. Momeni, V. Godinez, Victor Giurgiutiu, Paul Ziehl, J. Yu

Faculty Publications

Monitoring of fatigue cracking in steel bridges is of high interest to many bridge owners and agencies. Due to the variety of deterioration sources and locations of bridge defects, there is currently no single method that can detect and address the potential sources globally. In this paper, we presented a dual mode sensing methodology integrating acoustic emission and ultrasonic wave inspection based on the use of low-profile piezoelectric wafer active sensors (PWAS). After introducing the research background and piezoelectric sensing principles, PWAS crack detection in passive acoustic emission mode is first presented. Their acoustic emission detection capability has been validated …

Piezoelectric Wafer Active Sensors In Lamb Wave-Based Structural Health Monitoring, Lingyu Yu, Victor Giurgiutiu

Faculty Publications

Recent advancements in sensors and information technologies have resulted in new methods for structural health monitoring (SHM) of the performance and deterioration of structures. The enabling element is the piezoelectric wafer active sensor (PWAS). This paper presents an introduction to PWAS transducers and their applications in Lamb wave-based SHM. We begin by reviewing the fundamentals of piezoelectric intelligent materials. Then, the mechanism of using PWAS transducers as Lamb wave transmitters and receivers is presented. PWAS interact with the host structure through the shear-lag model. Lamb wave mode tuning can be achieved by judicious combination of PWAS dimensions, frequency value, and …

Dual Mode Sensing With Low-Profile Piezoelectric Thin Wafer Sensors For Steel Bridge Crack Detection And Diagnosis, Lingyu Yu, Sepandarmaz Momeni, Valery Godinez, Victor Giurgiutiu, Paul Ziehl, Jianguo Yu

Faculty Publications

Monitoring of fatigue cracking in steel bridges is of high interest to many bridge owners and agencies. Due to the variety of deterioration sources and locations of bridge defects, there is currently no single method that can detect and address the potential sources globally. In this paper, we presented a dual mode sensing methodology integrating acoustic emission and ultrasonic wave inspection based on the use of low-profile piezoelectric wafer active sensors (PWAS). After introducing the research background and piezoelectric sensing principles, PWAS crack detection in passive acoustic emission mode is first presented. Their acoustic emission detection capability has been validated …

Energy Savings And Peak Demand Reduction Of A Seer 21 Heat Pump Vs. A Seer 13 Heat Pump With Attic And Indoor Duct Systems - December 2011, Florida Solar Energy Center, James Cummings

FSEC Energy Research Center®

Experiments were run in an unoccupied 1600 ft2 house, the Manufactured Housing (MH Lab) at the Florida Solar Energy Center (FSEC), to evaluate the delivered performance as well as the relative performance of a SEER 21 variable capacity heat pump versus a SEER 13 heat pump. The performance was evaluated with two different duct systems: a standard attic duct system and an indoor duct system located in a dropped-ceiling space.