Other Mechanical Engineering Commons^™

Influence Of Magnetic Nanoparticles And Magnetic Stress On An Ionic Liquid Electrospray Source, Kurt Joseph Terhune

Dissertations, Master's Theses and Master's Reports

Two electrospray sources were developed to operate on an ionic liquid ferrofluid; one source was a pressure‑fed capillary electrospray source and the other was a novel electrospray source which used a magnetically‑induced instability to produce a peak from which an electric field could extract electrospray. Multiple characteristics of electrospray operation were examined for both sources using faraday plates/cups, a quartz crystal microbalance, a retarding potential analyzer, and a time-of-flight mass spectrometer. The ILFF electrosprays for a capillary source were shown to operate in a mixed ion/droplet regime. The mass flow of the electrospray beam was primarily transported by larger particles …

Test 2183: Claas Axion 880, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

The Design And Testing Of A High Performance Formula Sae Powertrain, Ryan T. Harty

Williams Honors College, Honors Research Projects

Every year the Society of Automotive Engineers (SAE) tasks collegiate students with designing, constructing, testing, and competing with an open wheel formula style racecar. This vehicle has to meet stringent technical requirements that are provided in a rule book published by SAE. The Formula SAE (FSAE) rule book is a very comprehensive set of requirements that are centered on safety of the driver of the vehicle and the safety of the track workers. The students are required to read and understand the rulebook in order to use sound engineering practices to build not only a high performing vehicle but a …

Atomically Informed Nonlocal Semidiscrete Variational Peierls-Nabarro Model For Planar Core Dislocations, Guisen Liu, Xi Cheng, Jian Wang, Kaiguo Chen, Yao Shen

Department of Mechanical and Materials Engineering: Faculty Publications

Prediction of Peierls stress associated with dislocation glide is of fundamental concern in understanding and designing the plasticity and mechanical properties of crystalline materials. Here, we develop a nonlocal semi-discrete variational Peierls-Nabarro (SVPN) model by incorporating the nonlocal atomic interactions into the semi-discrete variational Peierls framework. The nonlocal kernel is simplified by limiting the nonlocal atomic interaction in the nearest neighbor region, and the nonlocal coefficient is directly computed from the dislocation core structure. Our model is capable of accurately predicting the displacement profile, and the Peierls stress, of planar-extended core dislocations in face-centered cubic structures. Our model could be …

Photoluminescence From Radiative Surface States And Excitons In Methylammonium Lead Bromide Perovskites, Dengyang Guo, Davide Bartesaghi, Haotong Wei, Eline M. Hutter, Jinsong Huang, Tom J. Savenije

Department of Mechanical and Materials Engineering: Faculty Publications

In view of its band gap of 2.2 eV and its stability, methylammonium lead bromide (MAPbBr₃) is a possible candidate to serve as a light absorber in a subcell of a multijunction solar cell. Using complementary temperature-dependent time-resolved microwave conductance (TRMC) and photoluminescence (TRPL) measurements, we demonstrate that the exciton yield increases with lower temperature at the expense of the charge carrier generation yield. The low-energy emission at around 580 nm in the cubic phase and the second broad emission peak at 622 nm in the orthorhombic phase originate from radiative recombination of charges trapped in defects with …

Helium Irradiation And Implantation Effects On The Structure Of Amorphous Silicon Oxycarbide, Qing Su, Shinsuke Inoue, Manabu Ishimaru, Jennifer A. Gigax, Tianyao Wang, Hepeng Ding, Michael J. Demkowicz, Lin Shao, Michael Nastasi

Department of Mechanical and Materials Engineering: Faculty Publications

Despite recent interest in amorphous ceramics for a variety of nuclear applications, many details of their structure before and after irradiation/implantation remain unknown. Here we investigated the short-range order of amorphous silicon oxycarbide (SiOC) alloys by using the atomic pair-distribution function (PDF) obtained from electron diffraction. The PDF results show that the structure of SiOC alloys are nearly unchanged after both irradiation up to 30 dpa and He implantation up to 113 at%. TEM characterization shows no sign of crystallization, He bubble or void formation, or segregation in all irradiated samples. Irradiation results in a decreased number of Si-O bonds …

Suspended Graphene-Based Gas Sensor With 1-Mw Energy Consumption, Jong-Hyun Kim, Qin Zhou, Jiyoung Chang

Department of Mechanical and Materials Engineering: Faculty Publications

This paper presents NH₃ sensing with ultra-low energy consumption for fast recovery and a graphene sheet based on a suspended microheater. Sensitivity and repeatability are important characteristics of functional gas sensors embedded in mobile devices. Moreover, low energy consumption is an essential requirement in flexible and stretchable mobile electronics due to their small dimension and fluctuating resistivity during mechanical behavior. In this paper, we introduce a graphene-based ultra-low power gas detection device with integration of a suspended silicon heater. Dramatic power reduction is enabled by a duty cycle while not sacrificing sensitivity. The new oscillation method of heating improves …

Vorticella: A Protozoan For Bio-Inspired Engineering, Sangjin Ryu, Rachel E. Pepper, Moeto Nagai, Danielle C. France

Department of Mechanical and Materials Engineering: Faculty Publications

In this review, we introduce Vorticella as a model biological micromachine for microscale engineering systems. Vorticella has two motile organelles: the oral cilia of the zooid and the contractile spasmoneme in the stalk. The oral cilia beat periodically, generating a water flow that translates food particles toward the animal at speeds in the order of 0.1–1 mm/s. The ciliary flow of Vorticella has been characterized by experimental measurement and theoretical modeling, and tested for flow control and mixing in microfluidic systems. The spasmoneme contracts in a few milliseconds, coiling the stalk and moving the zooid at 15–90 mm/s. Because the …

Design And Implementation Of An Air Multiplier Fan For Pc, George Demian

Williams Honors College, Honors Research Projects

Mechanical engineering student (B.S.) senior design project. Conception, design (SolidWorks), 3D printing & processing, testing of a scaled down air multiplier "bladeless" fan within a computer chassis as a cooling solution.

Human Centered Design Of An Open-Drum, Treadle Thresher For Quinoa Farmers In The Andes Of Northern Peru, Robert A. Hayes

Dissertations, Master's Theses and Master's Reports

Growing international demand for quinoa in recent years has led to increased production throughout its South American range, including the Peruvian Andes. Small-scale farmers, who are among the poorest Peruvians, are increasingly growing quinoa for both food security and economic benefit; however, manual harvesting activities, such as threshing, are labor-intensive and time-consuming. This report documents the design, construction and operation of prototype quinoa thresher in a rural village in Northern Peru. In addition, an overview of the history and evolutionary approach to design for the developing world is presented. From this overview, a series of criteria is considered for the …

The Emission And Particulate Matter Oxidation Performance Of A Scr Catalyst On A Diesel Particulate Filter With A Downstream Scr, Sagar Sharma

Dissertations, Master's Theses and Master's Reports

Selective catalytic reduction (SCR) systems along with a NH₃ slip control catalyst (ASC) offers NOₓ conversion efficiency >90 % with NH₃ slip < 20 ppm. However, future heavy duty diesel (HDD) engines are designed for higher engine-out NOₓ to improve fuel consumption. Consequently, there is a strong desire to further improve the NOₓ reduction performance of SCR systems, to meet the 2015 California Optional Low NOₓ Standard. SCR catalysts on a diesel particulate filter provide an effective solution to reduce NOₓ and PM using a single aftertreatment device. It also provides an opportunity to increase the SCR volume to achieve NOₓ conversion efficiency >95 %. A downstream SCR catalyst substrate can be used to get additional NO_x conversion by using the SCRF^® outlet NH₃ to increase the cumulative NOₓ conversion of the system.

In this study, NOₓ reduction, NH₃ slip and PM oxidation performance of a Cu-zeolite SCRF^® with a downstream Cu-zeolite SCR were investigated based on engine experimental data at steady state conditions. The experimental data were collected at varying SCRF^® inlet temperatures, space velocities, inlet …

Simulation Of Diesel Particulate Filter Regeneration Using Lattice Boltzmann Method, Kshitiz Kumar Jain

Dissertations, Master's Theses and Master's Reports

Lattice Boltzmann Method is a novel approach, which has shown promise in solving a wide variety of fluid flow problems including single and multi-phase flows in complex geometries. Volume elements of the fluid domain are considered to be composed of particles and these particles fall under a velocity distribution function at each grid point. Particles collide with each other under the influence of external forces and the rules of collision are defined so as to be compatible with the Navier-Stokes Equation. In the current work, LBM has been applied to Diesel Particulate filters which is a device used for reducing …

Low-Drag Events In Transitional Wall-Bounded Turbulence, Richard D. Whalley, Jae Sung Park, Anubhav Kushwaha, David J.C. Dennis, Michael D. Graham, Robert J. Poole

Department of Mechanical and Materials Engineering: Faculty Publications

Intermittency of low-drag pointwise wall shear stress measurements within Newtonian turbulent channel flow at transitional Reynolds numbers (friction Reynolds numbers 70 – 130) is characterized using experiments and simulations. Conditional mean velocity profiles during low-drag events closely approach that of a recently discovered nonlinear traveling wave solution; both profiles are near the so-called maximum drag reduction profile, a general feature of turbulent flow of liquids containing polymer additives (despite the fact that all results presented are for Newtonian fluids only). Similarities between temporal intermittency in small domains and spatiotemporal intermittency in large domains is thereby found.

Flowtaxis Of Osteoblast Migration Under Fluid Shear And The Effect Of Rhoa Kinase Silencing, Brandon D. Riehl, Jeong Soon Lee, Ligyeom Ha, Il Keun Kwon, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

Despite the important role of mechanical signals in bone remodeling, relatively little is known about how fluid shear affects osteoblastic cell migration behavior. Here we demonstrated that MC3T3-E1 osteoblast migration could be activated by physiologically-relevant levels of fluid shear in a shear stress-dependent manner. Interestingly, shear-sensitive osteoblast migration behavior was prominent only during the initial period after the onset of the steady flow (for about 30 min), exhibiting shear stress-dependent migration speed, displacement, arrest coefficient, and motility coefficient. For example, cell speed at 1 min was 0.28, 0.47, 0.51, and 0.84 μm min^-1 for static, 2, 15, and 25 …

Fluid-Structure Interaction In Abdominal Aortic Aneurysm: Effect Of Modeling Techniques, Shengmao Lin, Xinwei Han, Yonghua Bi, Siyeong Ju, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, the impact of modeling techniques on predicting the mechanical behaviors of abdominal aortic aneurysm (AAA) is systematically investigated. The fluid-structure interaction (FSI) model for simultaneously capturing the transient interaction between blood flow dynamics and wall mechanics was compared with its simplified techniques, that is, computational fluid dynamics (CFD) or computational solid stress (CSS) model. Results demonstrated that CFD exhibited relatively smaller vortexes and tends to overestimate the fluid wall shear stress, compared to FSI. On the contrary, the minimal differences in wall stresses and deformation were observed between FSI and CSS models. Furthermore, it was found that …

High Temperature Near-Field Nanothermomechanical Rectification, Mahmoud Elzouka, Sidy Ndao

Department of Mechanical and Materials Engineering: Faculty Publications

Limited performance and reliability of electronic devices at extreme temperatures, intensive electromagnetic fields, and radiation found in space exploration missions (i.e., Venus & Jupiter planetary exploration, and heliophysics missions) and earth-based applications requires the development of alternative computing technologies. In the pursuit of alternative technologies, research efforts have looked into developing thermal memory and logic devices that use heat instead of electricity to perform computations. However, most of the proposed technologies operate at room or cryogenic temperatures, due to their dependence on material’s temperature-dependent properties. Here in this research, we show experimentally—for the first time—the use of near-field thermal radiation …

Surface Charge Switchable And Ph-Responsive Chitosan/Polymer Core-Shell Composite Nanoparticles For Drug Delivery Application, W. F. Huang, C. P. Tsui, M. Yang, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

The mutually conflicting surface charge requirements for nanoparticles to have long circulation and good cell affinity have made the development of polymer nanoparticles for controlled drug delivery fall into a dilemma. In order to solve this problem, the first attempt has been made in this work to develop vancomycin loaded composite nanoparticles with a novel chitosan core and poly (lactide-co-glycolide) (PLGA) shell structure and with both pH-responsive and surface charge switchable properties. Spherical composite nanoparticles have been successfully fabricated through a modified emulsion-gelation method with a controllable size (316–573 nm), surface charge (–27.6–31.75 mV) and encapsulation efficiency up to 70.8%. …

Molecular Dynamics Simulations Of Heterogeneous Cell Membranes In Response To Uniaxial Membrane Stretches At High Loading Rates, Lili Zhang, Zesheng Zhang, John Jasa, Dongli Li, Robin O. Cleveland, Mehrdad Negahban, Antoine Jérusalem

Department of Mechanical and Materials Engineering: Faculty Publications

The chemobiomechanical signatures of diseased cells are often distinctively different from that of healthy cells. This mainly arises from cellular structural/compositional alterations induced by disease development or therapeutic molecules. Therapeutic shock waves have the potential to mechanically destroy diseased cells and/or increase cell membrane permeability for drug delivery. However, the biomolecular mechanisms by which shock waves interact with diseased and healthy cellular components remain largely unknown. By integrating atomistic simulations with a novel multiscale numerical framework, this work provides new biomolecular mechanistic perspectives through which many mechanosensitive cellular processes could be quantitatively characterised. Here we examine the biomechanical responses of …

High-Velocity Projectile Impact Induced 9r Phase In Ultrafine-Grained Aluminium, Sichuang Xue, Zhe Fan, Olawale B. Lawal, Ramathasan Thevamaran, Qiang Li, Yue Liu, K. Y. Yu, Jian Wang, Edwin L. Thomas, Haiyan Wang, Xinghang Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

Aluminium typically deforms via full dislocations due to its high stacking fault energy. Twinning in aluminium, although difficult, may occur at low temperature and high strain rate. However, the 9R phase rarely occurs in aluminium simply because of its giant stacking fault energy. Here, by using a laser-induced projectile impact testing technique, we discover a deformation-induced 9R phase with tens of nm in width in ultrafine-grained aluminium with an average grain size of 140 nm, as confirmed by extensive post-impact microscopy analyses. The stability of the 9R phase is related to the existence of sessile Frank loops. Molecular dynamics simulations …

Controllable Energy Absorption Of Double Sided Corrugated Tubes Under Axial Crushing, Hozhabr Mozafari, Shengmao Lin, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

To maximize the controllable energy absorption of corrugation troughs as observed in the single sided corrugated (SSC) tube, we proposed and tested a new structure design, i.e., double-sided corrugated (DSC) tube made of Al 6060-T6 aluminum alloy or CF1263 carbon/epoxy composite. Finite element models were developed to test the mechanical advantage of the DSC tube in comparison with both SSC and classical straight (S) tubes under axial crushing. Results have shown that the total absorbed energy of the DSC aluminum tube with 14 corrugations was 330% and 32% higher than that of the SSC tube with 14 corrugations and the …