Other Mechanical Engineering Commons^™

Cp Check Valve Design, Alec B. Der Matoian, Jessica M. Dent, Skylar M. Tusting

Mechanical Engineering

This report is to serve as a final design review and update to the project sponsors at Zurn Wilkins for the Check Valve Design Senior Project. The senior project team was tasked with improving upon the design of Zurn Wilkins’ backflow prevention assembly for small diameter pipes by reducing the pressure loss created by the check valves within the double check backflow assembly. The information contained in this report builds off the information contained in the Critical Design Report (CDR), as well as feedback and further investigation suggested during an Intermediary Design Review. Based on conclusions from the CDR, our …

Atmospheric Water Harvester, Justin K. Lam, Jacob David, Jessica Mabry, Ben Brough

Mechanical Engineering

Atmospheric water harvesting uses the vapor-compression cycle to collect water from the moisture in the air. The system’s components include an evaporator, condenser, compressor, fan, and several expansion valves. Condensate from the air is then funneled into a receptacle, which determines the efficiency of the water harvesting system. For this senior project, the goal is to increase the efficiency of an existing atmospheric water harvester.

Atmospheric Water Harvester, Adam C. Goldstein, Scott Seno, Kristen E. Dentici

Mechanical Engineering

Access to potable water is a global issue that has yet to be adequately solved. In regions with limited access to electricity and ground or surface water, it is not always possible to provide clean water requiring external power or extensive infrastructure to implement. This Final Design Report document will outline the background, design and manufacturing plan involved in the development of a passive atmospheric water harvester. This report builds on the earlier Preliminary Design Review and Critical Design Review documents to reflect further research, analysis, comments from reviewers, and detailed design documentation. While a final design was decided on …

Optical Filter Selector, Camaryn Chambers, Joel Pitzer, Matthew Allen, Callen Schwefler

Mechanical Engineering

One of the many challenges with launching projectiles into space is predicting how the environment in space will affect the trajectory. One way to do this is to look at optical emissions, also known as airglow, which can only be seen from earth with sensitive equipment. By taking measurements of the light from the airglow, properties about the upper atmosphere can be inferred. This is important because variability in the atmosphere can cause variability in space that can affect astronauts and satellites. In order to accomplish this task, optical filters must be used to observe different bands of wavelengths of …

Design Of A 5 Degree Of Freedom Kinematic Stage For The Dual Crystal Backlighter Imager Diagnostic, Nicholas Nguyen

Master's Theses

The National Ignition Facility (NIF) is home to the world’s most energetic laser. The facility is one of the leading centers in inertial confinement fusion (ICF) experiments to research and understand sustainable fusion energy. To fully document and understand the physics occurring during experiments, precise diagnostics are used for a wide range of purposes. One diagnostic, the crystal backlighter imager (CBI), allows for X-ray imaging of the target at late stages of its implosion.

The aim of this project was to increase the current capabilities of the CBI diagnostic with the addition of a second crystal. This thesis focuses on …

Rsvp Spaceship!, Taylor Chavez, Deven Frauenhofer, Andrew Nott, Zoe Riesen

Mechanical Engineering

This document outlines the Final Design Review of a mechanical engineering senior design project at California Polytechnic State University San Luis Obispo. The project was to design and build a spaceship prop that will deploy during the performance put on by the Sound Design program within the Music Department. This performance, RSVP, is in its 25th year. Dr. Antonio G. Barata, the artistic director and producer of RSVP, is sponsoring the project. The key constraints include keeping the prop hidden in a confined space (under a stage that is comprised of multiple 4 ft. by 8 ft. by 3 ft. …

Design For Additive Manufacturing, Michael Charonnat, Leonardo Franco-Muñoz, Sam Noble, J.P. Purdom

Mechanical Engineering

This document outlines the critical design details and timeline for the Design for Additive Manufacturing Senior Project sponsored by Solar Turbines, Inc. The scope of this project encompasses the redesign of two of Solar Turbine’s cast parts for metal additive manufacturing in order to minimize lead time, cost, and weight. With the overall objective of performing in-depth analysis exploring affordability & feasibility, this redesign process will aid Solar Turbines in expanding their knowledge of Design for Additive Manufacturing principles and enable them to further incorporate the use of additive manufacturing into their production processes. The first part that the team …

California Solar Regatta - Hull Team: Up A Creek, Torrey Duncan, Sean Neuman, Kyle Krietzman, Andrew Offhaus

Mechanical Engineering

The SMUD Solar Regatta competition tasks students with developing a solar-powered watercraft to compete in various events on a fresh water lake. Cal Poly has created two mechanical engineering senior project groups to coordinate the design of a boat for the Solar Regatta competition. Up a Creek, the boat construction team, has created the following Final Design Review document to highlight the group’s progress on the project over the year. This document captures the design process from the background research, project objectives, and early concepts to the final design, manufacturing processes, and planned testing procedures. Unfortunately, the COVID-19 pandemic halted …

Numerical Methods For Predicting The Dynamic Crushing Response And Energy Absorption Of Composite Aluminum Honeycomb Sandwich Structures, Cody R. Volk

Master's Theses

Edgewise crushing responses of composite aluminum honeycomb sandwich structures were predicted using finite element analysis (FEA) software LS-DYNA by modeling the honeycomb as a material with anisotropic properties. The goal of the project was to develop a process for modeling the sandwich structure to rapidly iterate possible solutions for a safer workstation train table. Current workstation tables are too rigid and may cause injury or death in a head-on collision. Experimental compression tests were used to calibrate the aluminum honeycomb core with material type 26 (MAT 26, honeycomb). A published composite tensile test was used to validate the use of …

Blood Flow Simulation Of Particle Trapping In Models Of Arterial Bifurcations, Qihang Xu

McKelvey School of Engineering Graduate Student Theses & Dissertations

This thesis describes the particle trapping mechanism in blood flow in different arterial bifurcation models. For validation of CFD calculations, a T-junction model and a Y-junction model are analyzed. In both the models, there is one inlet pipe with two outlet pipes creating a symmetric bifurcation at some angle from the centerline of the inlet pipe. Naiver-Stokes (RANS) equations are solved for single phase laminar flow using the commercial CFD software ANSYS Fluent. After validation, Eulerian simulations are performed by using the Discrete Phase Model (DPM) for two-phase flow with particles injected in different bifurcation models with bifurcation angle of …

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb³⁺:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

Numerical Modeling Of Magnetic Fields For Mirror Neutron Search Experiment, Adam Johnston

Pursuit - The Journal of Undergraduate Research at The University of Tennessee

This paper will outline the configuration of 3D magnetic field model simulated from electric current sources using MATLAB. The model is using 3D arrays allowing for quick and accurate numerical approximations of Bio-Savart integrals, of error < , modeling the behavior of a magnetic field due to current carrying wires. We will discuss the development of a 3D magnetic field configuration produced by the current carrying wires around a large 2.5 m diameter vacuum beam tube in the proposed mirror neutron search experiment at High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). The simulations demonstrate that the magnetic field with uniformity better than ± 2.5 mG that will allow for optimal results in experiment within the controlled range of net magnetic field magnitudes |B| 500 mG and in the large vacuum tube along 20-m neutron flight path can be achieved for an approximately 6 cm radius section at the center of the tube.

Impact Of Magnetocaloric Material Properties On Performance Of A Magnetocaloric Heat Pump., Michael G. Schroeder

Electronic Theses and Dissertations

In the field of magnetocaloric heat pumps much research has been performed around machine design and theoretical machines, but little has been researched around practical problems such as variability in material properties. The present work defines a simulation tool that has been proven with experimental data. Magnetocaloric material cascades were statistically analyzed and parameterized, such that they could be recreated parametrically using a split Lorentz function with normally distributed parameters. Correlated curve-defining values with standard deviations were used as input into the simulation tool to determine the effect of variation on cooling heat pump performance for a household refrigerator application. …

Service Dog Ramp, Matthew Lundgren, Ariel Tolentino, Dallas Rocha, Adam Mayeda

Mechanical Engineering

This project involves designing a device to help a service dog easily get into and out of a truck. It details the design and manufacturing process. The project was interrupted due to the COVID-19 pandemic, so detailed instructions are provided for whoever takes on the project in the future.

Utilization Of Recycled Filament For 3d Printing For Consumer Goods, Alexa Peterson

Apparel Merchandising and Product Development Undergraduate Honors Theses

The 3D printing market has been used in a wide variety of manufacturing industries including textile and apparel. Many consumers can now own a personal 3D printer at home for recreational printing. There are even websites dedicated to 3D printing patterns made by consumers. However, the materials used in the 3D printing process pose a problem for the environment due to their plastic-based nature. 3D printing is a layered process with each layer being printed depending on the layer below it for strength and stability. During the 3D printing process, great amounts of waste are produced as a result of …

A History And Status Of Wind Energy Potential In Arkansas, Pre And Post Covid-19, Will Blasingame

Mechanical Engineering Undergraduate Honors Theses

Historically, wind-generated electricity has been the largest renewable energy sources in the United States. Wind-rich regions like Oklahoma and Texas have fueled growth and sold that electricity to electric utilities located in wind-poor states like Arkansas in the form of Power Purchase Agreements. Future technologies such as Vertical Axis Wind Turbines, small wind turbines, and Tesla turbines designed to generate electricity from wind show promise in unlocking more expensive wind resources in regions like Northwest Arkansas by mitigating concerns about low wind speeds and noise. However, more factors than just feasibility influence the growth of wind power. Governmental policies such …

Mathematical Modeling Of A Variable Mass Rocket’S Dynamics Using The Differential Transform Method, Ashwyn Sam

Honors Theses

In this paper, the mathematical modelling of a rocket with varying mass is investigated to construct a function that can describe the velocity and position of the rocket as a function of time. This research is geared more towards small scale rockets where the nonlinear drag term is of great interest to the underlying dynamics of the rocket. A simple force balance on the rocket using Newton’s second law of motion yields a Riccati differential equation for which the solution yields the velocity of the rocket at any given time. This solution can then be integrated with respect to time …

Impact Of Part Thickness And Drying Conditions On Saturation Limits In Binder Jet Additive Manufacturing, Nathan B. Crane

Faculty Publications

Binder jetting (BJ) is a high build-rate additive manufacturing process with growing commercial interest. Growth in BJ applications is driven by the use of finer powders and improved post-processing methods that can produce dense, homogenous final parts. However, understanding of the basic droplet/powder interaction is relatively limited. This paper considers the impact of in-process drying, part geometry, and droplet size on a key printing parameter: binder saturation. Parts of varying thicknesses are printed with a range of saturation levels under various heating conditions. The ratio of the printed part mass to the theoretical part mass is used to detect bleeding. …

Emissivity Measurements Of Painted And Aerosol Deposited Thermographic Phosphors (Yag:Dy And Mfg:Mn), Wendy Flores-Brito

Mechanical Engineering ETDs

Combustion is one of the most difficult processes to model. Luminous flames are characteristically sooty, which creates a problem when modeling and calculating the combustion and heat transfer of the process; both of which are highly dependent on temperature and emissivity. Soot particle emissivity as well as gas contributions affect the heat transfer calculation and must be accounted for.

Thermographic phosphors (TP) are ceramic based phosphorescent materials that have a temperature dependent emission that can be exploited to obtain surface and gas temperature measurements, as well as 2D temperature maps. Emissivity knowledge is not needed to obtain temperature and is …

Fluid Power Vehicle Challenge, Jacob Torrey, Kayla Londono, Bryson Chan, Aaron Trujillo

Mechanical Engineering

The FPVC combines mechanical engineering disciplines to design and manufacture a vehicle that utilizes hydraulic power. The FDR covers the final manufacturing process and verification processes developed during the front end of research and analysis built upon the Critical Design Review (CDR) and the PDR (Preliminary Design Review). This report showcases the design decisions and extensive research that supports the continuing efforts by the Team Pump My Ride, to build upon the accomplishments of Cal Poly’s previous team, The Incompressibles. The FDR presents how Team Pump My Ride produced the design changes from the CDR and PDR to achieve improvements …