Other Mechanical Engineering Commons^™

Quantification Of Nitric Oxide Concentration Using Single-Walled Carbon Nanotube Sensors, Jakob Meier, Joseph Stapleton, Eric M. Hofferber, Abigail Haworth, Stephen D. Kachman, Nicole M. Iverson

Department of Mechanical and Materials Engineering: Faculty Publications

Nitric oxide (NO), a free radical present in biological systems, can have many detrimental effects on the body, from inflammation to cancer. Due to NO’s short half-life, detection and quantification is difficult. The inability to quantify NO has hindered researchers’ understanding of its impact in healthy and diseased conditions. Single-walled carbon nanotubes (SWNTs), when wrapped in a specific single-stranded DNA chain, becomes selective to NO, creating a fluorescence sensor. Unfortunately, the correlation between NO concentration and the SWNT’s fluorescence intensity has been difficult to determine due to an inability to immobilize the sensor without altering its properties. Through the use …

Mechanical Behavior Of Al–Al2cu–Si And Al–Al2cu Eutectic Alloys, Qian Lei, Jian Wang, Amitava Mitra

Department of Mechanical and Materials Engineering: Faculty Publications

In this study, laser rapid solidification technique was used to refine the microstructure of ternary Al–Cu–Si and binary Al–Cu eutectic alloys to nanoscales. Micropillar compression testing was performed to measure the stress–strain response of the samples with characteristic microstructure in the melt pool regions. The laser-remelted Al–Al₂Cu–Si ternary alloy was observed to reach the compressive strength of 1.59 GPa before failure at a strain of 28.5%, which is significantly better than the as-cast alloy with a maximum strength of 0.48 GPa at a failure strain of 4.8%. The laser-remelted Al–Cu binary alloy was observed to reach the compressive …

Sensitive X-Ray And Gamma-Ray Detectors Including Perovskite Single Crystals, Jinsong Huang, Haotong Wei

Department of Mechanical and Materials Engineering: Faculty Publications

Perovskite single crystal X-ray and gamma-ray radiation detector devices include an X-ray and gamma-ray wavelength responsive active layer including a perovskite single crystal. The perovskite single crystal is a perovskite single crystal having a structure of ABX₃ , wherein A is methyl ammonium ( CH₂NH₂+), C_S+, formamidinum ( H₂NCHNH₂+) , or Rb⁺ or a mixture thereof, B is Pb²⁺ which can be partially or completely replaced by other ions including Bi³⁺, Sb³⁺, Sn²⁺ or a mixture thereof, and X is a halide …

Jcati Carbon Fiber Recycling Shredder, Benjamin Cooley

All Undergraduate Projects

Once carbon fibers are cast into a resin and used in a composite material, retrieving those fibers can be a difficult task. However, it is beneficial to recycle and reuse the fibers from old unneeded components rather than pay the cost of acquiring new ones. The Joint Center for Aerospace Technology Innovation (JCATI) carbon fiber recycling device condenses the multistep process of extracting the fibers by integrating all steps into one automated device. In the previous version of the device, the cutting blades turned the long composite strips into thin fingers but did not sever them across the width.

The …

Balsa Wood Bridge, Anndie Watterson

All Undergraduate Projects

A model for a strong bridge that could span a set distance and rise up to allow for passage underneath was requested, and specifications for the design were given. The model bridge was designed out of balsa wood to meet all the requirements. Using structural and material analysis and simple mechanical designs, a bridge was designed and constructed out of balsa wood, wood glue, and metal components used for articulation that met all of the criteria set by the assigner. The bridge was tested to ensure all specifications were met. The resulting bridge can hold 20kg of weight suspended from …

Nebraska Summary: S1150a Fendt 1050, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary 1218s: Fendt 724 Vario Gen6, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Use Of Energy Consumption During Milling To Fill A Measurement Gap In Hybrid Additive Manufacturing, K. L. M. Avegnon, P. Noll, M. R. Uddin, G. Madireddy, R. Williams, A. Achuthan, M. P. Sealy

Department of Mechanical and Materials Engineering: Faculty Publications

Coupling additive manufacturing (AM) with interlayer peening introduces bulk anisotropic properties within a build across several centimeters. Current methods to map high resolution anisotropy and heterogeneity are either destructive or have a limited penetration depth using a nondestructive method. An alternative pseudo-nondestructive method to map high-resolution anisotropy and heterogeneity is through energy consumption during milling. Previous research has shown energy consumption during milling correlates with surface integrity. Since surface milling of additively manufactured parts is often required for post-processing to improve dimensional accuracy, an opportunity is available to use surface milling as an alternative method to measure mechanical properties and …

Test 2235: John Deere 8rt 340, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Electrostatic Flocking Of Salt-Treated Microfibers And Nanofiber Yarns For Regenerative Engineering, Alec Mccarthy, Kossi Loic M. Avegnon, Phil A. Holubeck, Demi Brown, Anik Karan, Navatha Shree Sharma, Johnson V. John, Shelbie Weihs, Jazmin Ley, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Electrostatic flocking is a textile technology that employs a Coulombic driving force to launch short fibers from a charging source towards an adhesive-covered substrate, resulting in a dense array of aligned fibers perpendicular to the substrate. However, electrostatic flocking of insulative polymeric fibers remains a challenge due to their insufficient charge accumulation. We report a facile method to flock electrostatically insulative poly(ε-caprolactone) (PCL) microfibers (MFs) and electrospun PCL nanofiber yarns (NFYs) by incorporating NaCl during preflock processing. Both MF and NFY were evaluated for flock functionality, mechanical properties, and biological responses. To demonstrate this platform's diverse applications, standalone flocked NFY …

A Method Of Identifying Allographs In Undeciphered Scripts And Its Application To The Indus Valley Script, Shruti Daggumati, Peter Revesz

Department of Mechanical and Materials Engineering: Faculty Publications

This work describes a general method of testing for redundancies in the sign lists of ancient scripts by data mining the positions of the signs within the inscriptions. The redundant signs are allographs of the same grapheme. The method is applied to the undeciphered Indus Valley Script, which stands out from other ancient scripts by having a large proposed sign list that contains dozens of asymmetric signs that have mirrored pairs. By a statistical analysis of mirrored asymmetric signs, this paper shows that the Indus Valley Script was multi-directional and the mirroring of signs often denotes only the direction of …

Monitoring Of Overhead Polymer Core Composite Conductors Under Excessive Mechanical Loads Using Fiber Bragg Grating Sensors, Daniel H. Waters

Electronic Theses and Dissertations

This combined experimental and numerical study addresses mechanical effects associated with static and dynamic loading of novel High Temperature Low Sag (HTLS) transmission line polymer core composite conductors. The developed methodology was successfully applied to ACCC® to explain the complex failure mechanisms associated with combined bending and tension loading. Furthermore, the use of Fiber Bragg Grating (FBG) sensors was investigated for the first time to monitor the ACCC® design during installation and in-service.

Transverse low-velocity impacts to the ACCC® conductor having either free or constrained end conditions and large axial tensile loads were performed. It was identified that the most …

Metallic Surface Doping Of Metal Halide Perovskites, Yuze Lin, Yuchuan Shao, Jun Dai, Tao Li, Yi Liu, Xuezeng Dai, Xun Xiao, Yehao Deng, Alexei Gruverman, Xiao Cheng Zeng, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Intentional doping is the core of semiconductor technologies to tune electrical and optical properties of semiconductors for electronic devices, however, it has shown to be a grand challenge for halide perovskites. Here, we show that some metal ions, such as silver, strontium, cerium ions, which exist in the precursors of halide perovskites as impurities, can n-dope the surface of perovskites from being intrinsic to metallic. The low solubility of these ions in halide perovskite crystals excludes the metal impurities to perovskite surfaces, leaving the interior of perovskite crystals intrinsic. Computation shows these metal ions introduce many electronic states close to …

Recurrence Network Analysis Of Design-Quality Interactions In Additive Manufacturing, Ruimin Chen, Prahalada K. Rao, Yan Lu, Edward W. Reutzel, Hui Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Powder bed fusion (PBF) additive manufacturing (AM) provides a great level of flexibility in the design-driven build of metal products. However, the more complex the design, the more difficult it becomes to control the quality of AM builds. The quality challenge persistently hampers the widespread application of AM technology. Advanced imaging (e.g., X-ray computed tomography scans and high-resolution optical images) has been increasingly explored to enhance the visibility of information and improve the AM quality control. Realizing the full potential of imaging data depends on the advent of information processing methodologies for the analysis of design-quality interactions. This paper presents …

Judo Wearable, Alison Waugh, Natalie Masters

Williams Honors College, Honors Research Projects

Design a wearable sensor array to determine if a judo throw fulfills the requirements to win a match

Process-Structure Relationship In The Directed Energy Deposition Of Cobalt-Chromium Alloy (Stellite 21) Coatings, Ziyad M. Smoqi, Joshua Toddy, Harold (Scott) Halliday, Jeffrey E. Shield, Prahalada K. Rao

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, we accomplished the crack-free directed energy deposition (DED) of a multi-layer Cobalt- Chromium alloy coating (Stellite 21) on Inconel 718 substrate. Stellite alloys are used as coating materials given their resistance to wear, corrosion, and high temperature. The main challenge in DED of Stellite coatings is the proclivity for crack formation during printing. The objective of this work is to characterize the effect of the input energy density and localized laser-based preheating on the characteristics of the deposited coating, namely, crack formation, microstructural evolution, dilution of the coating composition due to diffusion of iron and nickel from …

Automated Control System For The Remote-Controlled Torch Positioner, Christopher Ferguson, Anna Abate, Kyle Cramer, Alex Sabitsch, Jacob Stefanko

Williams Honors College, Honors Research Projects

The goal of this project is to design and implement a controls system for Dr. Morscher’s burner rig. The rig serves to simulate jet turbine conditions and test how materials, specifically ceramic matrix composites, react under high temperatures and stresses. Currently, the location of the torch relies solely on manual adjustments and has no automated control system. The improved design will automatically adjust the torch position based on the desired temperature of the sample being tested, therefore maintaining a steady environment for the sample. The current method of manual adjustments for regulating temperature is a crude solution that does not …

Rheology Of Particulate Suspensions With Non-Newtonian Fluids In Capillaries, Bin Xia, Paul Krueger

Mechanical Engineering Research

This resource contains the processed experimental measurements of the flow consistency index and flow behavior index, along with their trendlines, for the particulate suspensions investigated in "Rheology of Particulate Suspensions with Non-Newtonian Fluids in Capillaries" by Bin Xia and Paul S. Krueger.

Test-Retest Reliability And Minimal Detectable Change Of The Computerized Dynamic Posturography Proprio For Adults With Chronic Traumatic Brain Injury, Guilherme Manna Cesar, Thad W. Buster, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

Purpose: Balance deficits after brain injury, including reactive recovery from unexpected perturbations, can persist well after rehabilitation is concluded. While traditional clinical assessments are practical, the anticipatory nature of the tasks may mask perceptible balance control. Computerized dynamic posturography can directly quantify capacity to respond to unexpected, external perturbations. This study examined the reliability of the computerized dynamic posturography assessment with the device PROPRIO® 4000 in adults with traumatic brain injury and created the minimal detectable change for its standardized test.

Methods: Ten adults (ages 21–55 years) with chronic (average 10 ± 6 years post-injury) severe (loss of consciousness 2–75 …

Perceived Importance Of Aac Messages To Support Communication In Rehabilitation Settings, Susan Koch Fager, Judith M. Burnfield, Chase M Pfeifer, Tabatha Sorenson

Department of Mechanical and Materials Engineering: Faculty Publications

Purpose: Permanent or temporary speech loss can occur due to a variety of medical conditions and often requires individuals to use augmentative and alternative communication (AAC) strategies and technologies to support communication. The use of AAC in medical and rehabilitation settings is critical to ensure the health, safety and psychological well-being of communicatively vulnerable individuals.

Method: This study surveyed the perceived importance of communication messages within five categories (Basic Needs, Patient-Provider Specific Communication, Social, Feelings, and Messages for Young Children) by individuals with disability who have undergone recent medical care as well as by rehabilitation care providers.

Results: Results indicated …