Manufacturing Commons^™

Experimental Investigation Of The Manufacture Of Tunable Graphene Oxide Filter Membranes Using Intense Pulse Light, Joshua H Kotter

Electronic Theses and Dissertations

Reduced graphene oxide is a thin, strong, and inexpensive material with a channel and pore structure that make it a promising candidate for a filtration material. Reduced graphene oxide has been produced and tested in the laboratory, but a lack of scalable manufacturing techniques have limited its commercial use.

This thesis has shown that graphene oxide can be rapidly manufactured with an industrially scalable flash reduction process. The flash reduction process uses 0.58 millisecond pulses from a xenon lamp to reduce the graphene oxide film in less than a minute. Results for partially reduced graphene oxide membranes tuned by the …

Design And Manufacture Of An Inertial Cascade Impactor For Industrial Hygiene Purposes, Hector Joel Gortaire

Mechanical & Aerospace Engineering Theses & Dissertations

Inertial cascade impactors are devices commonly used for industrial hygiene and pharmaceutical studies. Their main purpose is to separate particulate matter suspended in aerosols according to their sizes, which can vary from over 10 µm to 0.5 µm. Their versatility and ease of operation make them suitable for on-site sampling; however, designing them requires a careful consideration of the different geometric parameters that characterize them.

In this thesis, a 5-stage inertial cascade impactor was designed, modelled, constructed, and tested. The main design parameter was the volumetric flow rate, 40 l/min, which was provided by a vacuum pump. By continuous iterations, …

(Poster) Pneumatically Assisted Autocutter: Providing A Safe Workplace Environment For People With Disabilities, Ryan Kallenberger, Brian Galliher, Laura Johnson, Melanie Moore, Joseph Herzog, Renny Fernandez, Najmus Saqib

ASEE IL-IN Section Conference

We present a pneumatic autocutter to help workers with disabilities for reduced operator fatigue, increased efficiency, thereby giving enhanced capabilities when working on a production line without worrying about their ability to effectively do their jobs. We are students in a sophomore level six sigma based course through the R.B. Annis School of Engineering at the University of Indianapolis. The specific process of production being discussed involves cutting bulky cardboard frames with a metallic wire-mesh covering. The current process requires a considerable amount of physical labor from the operator; prolonged work results in gradial operator debility and injury. For Gateway …

Fracture Toughness And Fatigue Crack Growth Rate Characterization Of Inconel 718 Formed By Laser Powder Bed Fusion, Charles C. Hohnbaum

Theses and Dissertations

Continuing improvement in the field of AM of metals provides the opportunity for direct fabrication of aerospace parts. AM was once used in large part for rapid prototyping but improvements in technology and increases in the knowledge base of AM materials has provided the opportunity for manufacture of AM parts for operational use. The ability to create low numbers of unique parts without having to invest in expensive tooling provides great economic incentive to utilize this technique. IN718 is the most common high temperature alloy used in the aerospace industry and lends itself readily to formation by LPBF. The superior …

Providing A Meaningful Lab Experience For A Manufacturing Processes Course, Kevin Molyet

ASEE IL-IN Section Conference

No abstract provided.

Process Parameter Development Of Additively Manufactured Af9628 Weapons Steel, Erin M. Hager

Theses and Dissertations

The manufacture of components in Additive Manufacturing processes is limited by the range of materials available. Qualification of materials for Additive Manufacturing is time intensive, and is often specific to a single type of machine. In this study, an approach to selecting power, speed, and hatch spacing values for a newly powderized material, AF9628 weapons steel, is described that results in highly dense (>99.9%) parts on an MLab 200R Cusing. Initial power and speed values used in a weld track study were selected based on a survey of parameters used on similar materials, with a focus on the energy …

Microscale Metal Forming: Mesoscopic Size Effect, Extrusion And Molding, Bin Zhang

LSU Doctoral Dissertations

The continuing trend of metallic device and product miniaturization has motivated studies on microscale metal forming technologies. A better understanding of materials’ mechanical response and deformation behavior is of importance for the design and operation of micro metal forming processes. In this dissertation, uniaxial compression testing was conducted on Al ring and pillar specimens with characteristic dimensions at meso to micro scales. The experimental data reveal inadequacies of the existing surface layer model and provides a baseline for delineating deformation mechanisms in micro metal forming operations. Microscale reverse extrusion experiment was carried out on Cu and Al rod specimens with …

Torsional Stiffness Of A Race Car, Reiley A. Schraeger, Cameron Kao, Raymond Deng, Omar Roman

Mechanical Engineering

Torsional stiffness plays a major role in any road vehicle. To understand torsional stiffness of a vehicle and make future iterations and improvements, a proper torsional stiffness jig is required to prove accurate and useful data. This report encompasses the new and improved testing jig and potential improvement ideas for more accurate results. With real data result relating to FEA calculations, designers can be confident in the FEA changes to torsional stiffness is accurate and will yield the probably results they desired. This report shows the methodology, manufacturing process and testing procedure to use on any Baja or SAE vehicle …

Application Of Metamaterials For Multifunctional Satellite Bus Enabled Via Additive Manufacturing, Michael A. Macchia

Theses and Dissertations

Space systems require materials with superior stiffness to weight ratios to provide structural integrity while minimizing mass. Additive manufacturing processes enable the design of metamaterials that exceed the performance of naturally occurring materials in addition to allowing the integration of non-structural functions. This research explored the use of a high stiffness, high density, small melt pool track width AM material, Inconel 718, to enable the production of metamaterials with finer features possible than can possibly be created using a lower density aluminum alloy material. Various metamaterials were designed utilizing thin wall triply periodic minimal surface infilled sandwich structures. The performance …

Investigation Of Design, Manufacture, Analysis, And Test Of A Composite Connecting Rod Under Compression, Thomas Juhl Rohrbach

Master's Theses

Composite materials hold great potential for the replacement of traditional materials in machines utilized on a daily basis. One such example is within an engine block assembly where massive components inherently reduce the efficiency of the system they constitute. By replacing metal elements such as connecting rods, cylinder caps, or a crank shaft with composite alternatives, a significant increase in performance may be achieved with respect to mechanical strength, thermal stability, and durability, while also reducing mass. Exploration of this technology applied to a connecting rod geometry was investigated through a combination of process development, manufacturing, numerical analysis and testing. …

Carbon Fiber Recycler : Fiber Reclaimer, Alexander Edwards

All Undergraduate Projects

Boeing uses composite components for the 777x aircraft. The production of composite parts results in flashing (excess material) that must be trimmed and "thrown away" as scrap. Boeing is investigating means of recycling these scraps. The method proposed for this project is to delaminate and shred the composite material. The delamination process uses a ram to press two claw shaped devices together that bends and deforms the material in opposite directions. The chipper process uses counter rotating saw blades spaced 1/8” apart to produce small shredded material. This shredding material is pyrolyzed (heated) to decay the resin leaving the carbon …

Medallion Manufacturing, Luis Perez

All Undergraduate Projects

A more efficient manufacturing process is needed to create the approximately 30 MET medallions, given to the graduating class. The process must be repeatable, consistent, and efficient. The objective is to create a method that can remain the same year to year, save time, and be repeated by anybody. Two approaches were developed: a casting method, and a machining method involving a computer numerically controlled (CNC) mill. The casting method began with a match plate was developed by attaching 3D printed models and runners to plywood. The design was evaluated before the pour using SolidCast software. Special attention was directed …

Custom Designed Wall Mounted Shop Crane, Bradley Lewis

All Undergraduate Projects

The objective of this project was to design and fabricate a custom wall mounted jib crane to specific, non-standard dimensions. The crane was designed to be industry rated for 2000 pounds, rotate at least 180 degrees, and be designed to have a maximum boom length tailored to the specific installation site. Two potential installation sites and purposes were selected for construction: inside the bay doors of a fabrication shop, intended to transfer large pieces of material to and from a plasma table, and inside a car maintenance garage, intended to lift and remove engines and transmissions from cars.

Design of …

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …

Composite Recycler: Delamination, Nathan Sauer

All Undergraduate Projects

A great deal of composite waste is generated in the construction of wings for the Boeing 777. These carbon fiber “wing trimmings” are currently being disposed of in a landfill. These carbon fiber boards are made of several layers laminated together, making them very rigid and hard to recycle. This report proposes a method to delaminate the layers of these composite wing trimmings using a hydraulic press and a V-shaped steel die so that they may be more easily shredded and thus recycled. A top, “male” die with two points is pressed into a bottom, “female” die with three points …

The Bracket, Ryan Jerome Skerbeck

All Undergraduate Projects

• Abstract
• Bracket, casting, aluminum; if any of these for mentioned words interest you in anyway this is a document that you should read.
• There is a need for a compressor to be mounted to the front of a Cummins engine so that compressed air would be available on a work truck. The York compressor and the engine were known quantities, so what this project covered was the bracket that mounted the compressor to the engine and the manufacturing processes. The process chosen to make the bracket was aluminum casting; casting was chosen because of the ease of making many parts …

Process Sustainability Evaluation For Manufacturing Of A Component With The 6r Application, Ana E. Bonilla Hernández, Tao Lu, Tomas Beno, Claes Fredriksson, Ibrahim S. Jawahir

Institute for Sustainable Manufacturing Faculty Publications

Sustainability in manufacturing can be evaluated at product, process and system levels. The 6R methodology for sustainability enhancement in manufacturing processes includes: reduced use of materials, energy, water and other resources; reusing of products/components; recovery and recycling of materials/components; remanufacturing of products; and redesigning of products to utilize recovered materials/resources. Although manufacturing processes can be evaluated by their productivity, quality and cost, process sustainability assessment makes it a complete evaluation. This paper presents a 6R-based evaluation method for sustainable manufacturing in terms of specific metrics within six major metrics clusters: environmental impact, energy consumption, waste management, cost, resource utilization and …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

Ua66/1/5 Ogden College Of Science & Engineering Dean's Office Centers, Wku Archives

WKU Archives Collection Inventories

Records created by and about centers associated with the Dean's office in the Ogden College of Science & Engineering.

Custom Foot Prosthetic: Diabetic Care, Chandler Streuli

All Undergraduate Projects

Across the United States there are people every day who lose their toes to diabetes or to loss of circulation within their legs. The problem becomes building a more cost effective and efficient prosthetic for these individuals. The prosthetics that are used for medical purposes are often costly, especially without the help of insurance. The new prosthetic was designed to be taken in and out of shoes so that it is fast and easy for the user to move the device from shoe to shoe. The manufacturing method for this project was using a 3D printer to build the initial …