Manufacturing Commons^™

Less-Than-Lethal Self Defense Device With An Acoustic Element, Anthony Taibi

KSU Journey Honors College Capstones and Theses

This creative capstone project involves the conception, design, and creation of a less-than-lethal self defense device with an integrated sound board to control the acoustic element. Theoretically, this device is capable of deterring potential threats without causing any serious harm or any long-term damage. When starting this project, I was very focused on sonic warfare, and how to harness the power of ultrasonic and infrasonic sound waves to subdue to target; however, I concluded that using resonant frequencies to deter a human being is too dangerous, expensive, and can have negative effects for the user of the device if used …

Method And Apparatus For Fabricating Ceramic And Metal Components Via Additive Manufacturing With Uniform Layered Radiation Drying, Ming-Chuan Leu, Amir Ghazanfari, Wenbin Li, Greg Hilmas, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A freeform extrusion fabrication process for producing three - dimensional ceramic, metal and functionally gradient composite objects, including the steps of filling a plurality of paste sources with a respective plurality of aqueous paste compositions, operationally connecting respective syringes containing respective aqueous paste compositions to a mix ing chamber, moving a first aqueous paste composition from a first respective paste source into the mixing chamber, moving a second aqueous paste composition from a second respective paste source into the mixing chamber, mixing the first and second aqueous paste compositions to define a first admixture having a first admixture composition, extruding …

Restore-L Satellite Servicing Internship Final Report, Giovanni Campos

Publications and Research

This paper reviews the Restore-L mission purpose and the necessary research and simulations to meet mission specification for the Propellant Transfer Subsystem (PTS). It is essential the PTS undergoes functionality testing, environmental testing, and calculations to understand the capabilities of the system. For the testing of components from PTS, a proper test setup is required. It is vital for test hardware, such as hoses and valves, to stay in place while the test is being performed. For the test hardware to operate correctly, positioning, orientation, and alignment are critical as well. In addition to the testing, calculations for pressure drop …

Mechanical And Tribological Behaviour Of Treated And Untreated Moringa Oleifera Pods Fiber Reinforced Epoxy Polymer Composite For Packaging Applications, Prakash Sampath, Senthil Kumar V.S Dr

Journal of Applied Packaging Research

Researchers now focus on the use of natural fiber polymer composites materials for packing applications. This attention is due to their low cost and renewable characteristics. Fabrication of composites with the use of renewable resources has many benefits of alternating from an appropriate management and reduction in industrial wastages, ecofriendly behaviour to cost effectiveness. The artificial fibers in packing industries can be replaced by natural fibers in the areas where stiffness and high strength are not the primary requirement. In the last decade the use of Natural fibers in the place of artificial fibers for reinforcements in epoxy resin matrix …

The Influence Of Process Variables On Physical And Mechanical Properties In Laser Powder Bed Fusion, Joshua Robert Koepke, Bradley Jared, Yu-Lin Shen

Mechanical Engineering ETDs

Laser powder bed fusion additive manufacturing consists of a process that incorporates many process variables into fabricating parts. This study investigated several of these process variables and determined their influence on part properties. The process variables investigated include laser power, velocity, focus offsets, layer thickness, and powder particle size. Physical properties will be compared including surface roughness, form, and density. Tensile testing provided mechanical properties including unloading Young’s modulus, ultimate tensile strength, yield strength, uniform elongation, and ductility. Process maps will be developed that will provide recommendations for these process settings. It will be shown that these laser settings can …

Extrusion Production Of 3d Printer Filament For Additive Manufacturing, Patrick Hardy, Cole Angermayer, Rhett Lokey, Rebeca Book, Jeanne H. Norton

Posters

Additive manufacturing, also known as 3D printing, is becoming a go-to production method for short production runs and rapid prototyping on a commercial scale. The growth of additive manufacturing is due to many fac­tors including development of concept modeling, product designing, prototyping, and customized parts. Pittsburg State University’s College of Technology strives to stay at the cutting edge of processing materials for additive manufacturing. The capability of making our own 3D-printer filament would allow students to work with new and different materials and would allow students to learn at the forefront of 3D printing technology. The Wayne Yellowjacket Extruder and …

Improved Molding Tool For Plastics Engineering Technology Injection Molder, Caleb Luthi, Tyler Burger, Andrew Huffman, Paul Herring, Jeanne H. Norton

Posters

Plastic injection molding is an extremely versatile, preferred method of producing plastic parts because it is ex­tremely efficient. In the business of injection molding, it is important to have machines and tools that work prop­erly to get the job done. One such tool is the mold, which forms high quality plastic parts. The main objective of this project is to refurbish the current Frisbee mold to create promotional products for PSU’s Department of Engineering Technology. Parts were created with the existing mold to determine what issues needed to be ad­dressed, including: excessive flash on the parts/runner, a poor runner/gate design, …

Hybrid Laser/Arc Welding Of Difficult-To-Weld Thick Steel Plates In Different Joint Configurations: Issues And Resolutions, Nima Yazdian

Mechanical Engineering Research Theses and Dissertations

Difficult-to-weld steels are ferrous alloys that are characterized by a low thermal conductivity, and large thermal expansion coefficient. These intrinsic features contribute to a high level of distortion and cracking susceptibility during joining of these types of steels. In an effort to address the issues associated with difficult-to-weld steels, highly concentrated beam spots like electron and laser beam welding were developed. Usage of tightly focused heat sources have been accompanied by several challenges. An extremely precise fit-up requirement was considered as the most significant issue corresponding to application of either laser or electron beam. Recently, it was found that the …

Analytical And Experimental Study Of Laser Cladding Of Ni/Wc Metal Matrix Powders Reinforced With Rare Earth Elements Using A High Power Direct Diode Laser, Mohammed Sayeed

Mechanical Engineering Research Theses and Dissertations

The corrosion and wear are major limiting factors for steel in the harsh environments and can be controlled by depositing protective passive coatings. Nickel based alloy cladding of steel offers a solution by enabling better corrosion and wear resistance, and high bonding strength. The laser surface cladding of steel was conducted using a high power direct diode laser. Layers of tungsten carbide in Ni (40%Ni-60%WC) combined with 1% and 2% Lanthanum Oxide (La₂O₃) and Cerium Oxide (CeO₂) were deposited on ASTM A36 steel substrate. The X-ray diffraction and scanning electron microscopy were employed to …

Design And Manufacture Of An Inertial Cascade Impactor For Industrial Hygiene Purposes, Hector Joel Gortaire

Mechanical & Aerospace Engineering Theses & Dissertations

Inertial cascade impactors are devices commonly used for industrial hygiene and pharmaceutical studies. Their main purpose is to separate particulate matter suspended in aerosols according to their sizes, which can vary from over 10 µm to 0.5 µm. Their versatility and ease of operation make them suitable for on-site sampling; however, designing them requires a careful consideration of the different geometric parameters that characterize them.

In this thesis, a 5-stage inertial cascade impactor was designed, modelled, constructed, and tested. The main design parameter was the volumetric flow rate, 40 l/min, which was provided by a vacuum pump. By continuous iterations, …

Experimental Investigation Of The Manufacture Of Tunable Graphene Oxide Filter Membranes Using Intense Pulse Light, Joshua H Kotter

Electronic Theses and Dissertations

Reduced graphene oxide is a thin, strong, and inexpensive material with a channel and pore structure that make it a promising candidate for a filtration material. Reduced graphene oxide has been produced and tested in the laboratory, but a lack of scalable manufacturing techniques have limited its commercial use.

This thesis has shown that graphene oxide can be rapidly manufactured with an industrially scalable flash reduction process. The flash reduction process uses 0.58 millisecond pulses from a xenon lamp to reduce the graphene oxide film in less than a minute. Results for partially reduced graphene oxide membranes tuned by the …

(Poster) Pneumatically Assisted Autocutter: Providing A Safe Workplace Environment For People With Disabilities, Ryan Kallenberger, Brian Galliher, Laura Johnson, Melanie Moore, Joseph Herzog, Renny Fernandez, Najmus Saqib

ASEE IL-IN Section Conference

We present a pneumatic autocutter to help workers with disabilities for reduced operator fatigue, increased efficiency, thereby giving enhanced capabilities when working on a production line without worrying about their ability to effectively do their jobs. We are students in a sophomore level six sigma based course through the R.B. Annis School of Engineering at the University of Indianapolis. The specific process of production being discussed involves cutting bulky cardboard frames with a metallic wire-mesh covering. The current process requires a considerable amount of physical labor from the operator; prolonged work results in gradial operator debility and injury. For Gateway …

Fracture Toughness And Fatigue Crack Growth Rate Characterization Of Inconel 718 Formed By Laser Powder Bed Fusion, Charles C. Hohnbaum

Theses and Dissertations

Continuing improvement in the field of AM of metals provides the opportunity for direct fabrication of aerospace parts. AM was once used in large part for rapid prototyping but improvements in technology and increases in the knowledge base of AM materials has provided the opportunity for manufacture of AM parts for operational use. The ability to create low numbers of unique parts without having to invest in expensive tooling provides great economic incentive to utilize this technique. IN718 is the most common high temperature alloy used in the aerospace industry and lends itself readily to formation by LPBF. The superior …

Providing A Meaningful Lab Experience For A Manufacturing Processes Course, Kevin Molyet

ASEE IL-IN Section Conference

No abstract provided.

Process Parameter Development Of Additively Manufactured Af9628 Weapons Steel, Erin M. Hager

Theses and Dissertations

The manufacture of components in Additive Manufacturing processes is limited by the range of materials available. Qualification of materials for Additive Manufacturing is time intensive, and is often specific to a single type of machine. In this study, an approach to selecting power, speed, and hatch spacing values for a newly powderized material, AF9628 weapons steel, is described that results in highly dense (>99.9%) parts on an MLab 200R Cusing. Initial power and speed values used in a weld track study were selected based on a survey of parameters used on similar materials, with a focus on the energy …

Microscale Metal Forming: Mesoscopic Size Effect, Extrusion And Molding, Bin Zhang

LSU Doctoral Dissertations

The continuing trend of metallic device and product miniaturization has motivated studies on microscale metal forming technologies. A better understanding of materials’ mechanical response and deformation behavior is of importance for the design and operation of micro metal forming processes. In this dissertation, uniaxial compression testing was conducted on Al ring and pillar specimens with characteristic dimensions at meso to micro scales. The experimental data reveal inadequacies of the existing surface layer model and provides a baseline for delineating deformation mechanisms in micro metal forming operations. Microscale reverse extrusion experiment was carried out on Cu and Al rod specimens with …

Investigation Of Design, Manufacture, Analysis, And Test Of A Composite Connecting Rod Under Compression, Thomas Juhl Rohrbach

Master's Theses

Composite materials hold great potential for the replacement of traditional materials in machines utilized on a daily basis. One such example is within an engine block assembly where massive components inherently reduce the efficiency of the system they constitute. By replacing metal elements such as connecting rods, cylinder caps, or a crank shaft with composite alternatives, a significant increase in performance may be achieved with respect to mechanical strength, thermal stability, and durability, while also reducing mass. Exploration of this technology applied to a connecting rod geometry was investigated through a combination of process development, manufacturing, numerical analysis and testing. …

Torsional Stiffness Of A Race Car, Reiley A. Schraeger, Cameron Kao, Raymond Deng, Omar Roman

Mechanical Engineering

Torsional stiffness plays a major role in any road vehicle. To understand torsional stiffness of a vehicle and make future iterations and improvements, a proper torsional stiffness jig is required to prove accurate and useful data. This report encompasses the new and improved testing jig and potential improvement ideas for more accurate results. With real data result relating to FEA calculations, designers can be confident in the FEA changes to torsional stiffness is accurate and will yield the probably results they desired. This report shows the methodology, manufacturing process and testing procedure to use on any Baja or SAE vehicle …

Application Of Metamaterials For Multifunctional Satellite Bus Enabled Via Additive Manufacturing, Michael A. Macchia

Theses and Dissertations

Space systems require materials with superior stiffness to weight ratios to provide structural integrity while minimizing mass. Additive manufacturing processes enable the design of metamaterials that exceed the performance of naturally occurring materials in addition to allowing the integration of non-structural functions. This research explored the use of a high stiffness, high density, small melt pool track width AM material, Inconel 718, to enable the production of metamaterials with finer features possible than can possibly be created using a lower density aluminum alloy material. Various metamaterials were designed utilizing thin wall triply periodic minimal surface infilled sandwich structures. The performance …

Carbon Fiber Recycler : Fiber Reclaimer, Alexander Edwards

All Undergraduate Projects

Boeing uses composite components for the 777x aircraft. The production of composite parts results in flashing (excess material) that must be trimmed and "thrown away" as scrap. Boeing is investigating means of recycling these scraps. The method proposed for this project is to delaminate and shred the composite material. The delamination process uses a ram to press two claw shaped devices together that bends and deforms the material in opposite directions. The chipper process uses counter rotating saw blades spaced 1/8” apart to produce small shredded material. This shredding material is pyrolyzed (heated) to decay the resin leaving the carbon …