An Investigation Into Energy-Material Properties Interaction In Additive Manufacturing Of Polymers.,
2021
University of Louisville
An Investigation Into Energy-Material Properties Interaction In Additive Manufacturing Of Polymers., Pu Han
Electronic Theses and Dissertations
Additive manufacturing (AM), known as three-dimensional (3D) printing, is a fabrication process to build 3D objects layer by layer based on computer aided design (CAD) model or digital 3D model. Fused filament fabrication (FFF) has become a preferred method for additive manufacturing due to its cost-effectiveness and flexibility. However, the parts built using FFF process suffer from lower mechanical strength compared to that fabricated using traditional method and rough surface finish. With this motivation, this dissertation aims to develop and implement a novel in-process laser assisted technique on FFF to heal the microstructure of FFF built objects by enhancing reptation …
Digital Design And Thermomechanical Process Simulation For 3d Printing With Abs And Soyhull Fibers Reinforced Abs Composites.,
2021
University of Louisville
Digital Design And Thermomechanical Process Simulation For 3d Printing With Abs And Soyhull Fibers Reinforced Abs Composites., Saleh Khanjar
Electronic Theses and Dissertations
Recent demonstrations with fused filament fabrication (FFF) 3D printing have shown to produce prototypes as well as production components. Additionally, due to the FFF process platforms being low-cost and readily available there has been a high-demand to produce on-demand parts for various applications in automotive, in-space manufacturing and electronic industries. However, current limitations such as limited availability of advanced composites materials, and guidelines for design-for-manufacturing make the process prone to trial-and-error experiments both at the materials development, product design and manufacturing stage. In this work, new thermomechanical process simulations platform, Digimat-AM has been evaluated to address and demonstrate digital design …
Materials And Process Design For Ceramic Fused Filament Fabrication (Cf3) Of Hydroxyapatite.,
2021
University of Louisville
Materials And Process Design For Ceramic Fused Filament Fabrication (Cf3) Of Hydroxyapatite., Kavish Sudan
Electronic Theses and Dissertations
Ceramic fused filament fabrication (CF3) enables the fabrication of highly customizable ceramic parts at relatively lower costs compared to other AM technologies. Advanced ceramics, having specific or niche applications, call for a high level of accuracy to meet the performance requirements. For achieving the desired level of accuracy in any manufacturing process, it is important to know the effect of involved parameters at different stages of fabrication. CF3 has been around for a while but there has been a severe lack of literature dealing with understanding the effect of process parameters on the final part properties. In this study, Hydroxyapatite …
Effect Of The Melt Pool Boundary Network On The Anisotropic Mechanical Properties Of Selective Laser Melted 304l,
2021
Missouri University of Science and Technology
Effect Of The Melt Pool Boundary Network On The Anisotropic Mechanical Properties Of Selective Laser Melted 304l, Myranda Spratt, Joseph William Newkirk, Okanmisope Fashanu, K. Chandrashekhara
Materials Science and Engineering Faculty Research & Creative Works
Anisotropic mechanical properties are a well-known issue in selective laser melted parts. The microstructure produced by selective laser melting (SLM) is directional, including the solidified melt pool structures and grains. This work investigates the melt pool boundary's effects on 304L stainless steel's compressive properties. 304L stainless steel solid cylinders were built using a pulse laser SLM machine in four directions using three hatch angle rotations: 0⁰, 67⁰, and 105⁰ . The twelve samples were compression tested, and the results were analyzed. Numerical models were also created with the different hatch angles and directions. The melt pool boundary network (MPBN) in …
Molecular Dynamics Study Of Atomic Diffusion In Cantor High Entropy Alloy In The Selective Laser Melting Process,
2021
The University of Texas Rio Grande Valley
Molecular Dynamics Study Of Atomic Diffusion In Cantor High Entropy Alloy In The Selective Laser Melting Process, Mathew Z. Farias
Theses and Dissertations
High entropy alloys (HEAs) are compositionally complex alloys that are comprised of 5 or more principle elements at near equimolar concentrations. The Selective Laser Melting (SLM) method generally melts pure elemental powders or prefabricated alloy powders, this process allows for the production of heterogeneous structures that would be difficult to create through more conventional means. In-situ alloying in SLM, or Laser Additive Alloying (LAA), using pure elemental powders is a promising means of producing what would otherwise be costly and difficult to fabricate products with less defects using prefabricated powders, therefore this new approach could enable the ability to …
Selective Laser Melting Of Titanium Diboride: A Study Of The Energy Density Effects,
2021
The University of Texas Rio Grande Valley
Selective Laser Melting Of Titanium Diboride: A Study Of The Energy Density Effects, Lazaro Lopez Mendez
Theses and Dissertations
Natural titanium diboride (TiB2) has been reported the 5th hardest material on earth. Due to its superior properties, such as high density, high elastic modulus, and high compressive strength, TiB2 becomes one of the most suitable ceramic reinforcements for applications with severe friction and heavy loading conditions. This study is intended to produce TiB2 using 3D additive manufacture (AM) technology, and then to understand the tribological property of the AM fabricated TiB2 specimens. In this study, a laser additive alloying (LAA) process was developed based on a Renishaw AM laser system. One mm thick samples were prepared using the LAA …
Product Lifecycle Management - Application Of Patterning Methods To Gas Turbine Blades And Creation Of Learning Materials,
2021
Clemson University
Product Lifecycle Management - Application Of Patterning Methods To Gas Turbine Blades And Creation Of Learning Materials, David Procopio
All Theses
To compete in the global marketplace, companies need to embrace virtual design and manufacturing methods. Product Lifecycle Management (PLM) embodies both the workflow processes and tools to bring forth products from conception to design to fabrication to service to decommissioning, and to eventual recycling. In response to the growing demand for engineers and technicians with these critical skills, colleges and universities should introduce these virtual tools through seminars, software workshops, and computer laboratory sessions. Some of the opportunities in the PLM Center at Clemson University include short courses on PLM practices, focused software training sessions, hands-on exploration activities, and research …
Design And Fabrication Of A Polymer Fdm Printer Capable Of Build Parameter Monitoring And In-Sit Geometric Monitoring Via Photogrammetry,
2021
Clemson University
Design And Fabrication Of A Polymer Fdm Printer Capable Of Build Parameter Monitoring And In-Sit Geometric Monitoring Via Photogrammetry, Travis Roberts
All Theses
Additive manufacturing, or 3D printing, is a complex process that creates free-form geometric objects by sequentially placing material in a location to construct an object, usually as a layer-by-layer process. One of the most widespread methods is Fused Deposition Modeling (FDM). FDM is used in many of the consumer-grade polymer 3D printers available today. While consumer grade machines are cheap and plentiful, they lack many of the features desired in a machine used for research purposes and are often closed-source platforms. Commercial-grade models are more expensive and are also usually closed-source platforms that do not offer flexibility for modifications often …
Benchmark Testing Of Gold Ribbon Bonds On Thin-Film Microchips With New Gold Ribbon Auto-Bonder,
2021
California Polytechnic State University, San Luis Obispo
Benchmark Testing Of Gold Ribbon Bonds On Thin-Film Microchips With New Gold Ribbon Auto-Bonder, Austin Conrad
Master's Theses
The focus of this document is on the gold ribbon bond testing and creation of a bonding map for the new gold ribbon Auto-Bonder at Keysight Technologies in Santa Rosa, California. The new Auto-Bonder replaces a nearly 50-year-old machine that no longer had any documentation for the original process of thin-film microchip ribbon bonding. The original process was developed in the early 1970s to provide an electrical connection from the top to the bottom of the microchip. The electrical connection takes the place of what would be a via in a modern silicon microchip. Gold wire bonding is a common …
Integration Of Blockchain Technology Into Automobiles To Prevent And Study The Causes Of Accidents,
2021
California State University, San Bernardino
Integration Of Blockchain Technology Into Automobiles To Prevent And Study The Causes Of Accidents, John Kim
Electronic Theses, Projects, and Dissertations
Automobile collisions occur daily. We now live in an information-driven world, one where technology is quickly evolving. Blockchain technology can change the automotive industry, the safety of the motoring public and its surrounding environment by incorporating this vast array of information. It can place safety and efficiency at the forefront to pedestrians, public establishments, and provide public agencies with pertinent information securely and efficiently. Other industries where Blockchain technology has been effective in are as follows: supply chain management, logistics, and banking. This paper reviews some statistical information regarding automobile collisions, Blockchain technology, Smart Contracts, Smart Cities; assesses the feasibility …
Additive Manufacturing Of Cork, A Cold Spray Technology,
2021
Mississippi State University
Additive Manufacturing Of Cork, A Cold Spray Technology, Kimberly Kay Dickey
Theses and Dissertations
Cold Spray Additive Manufacturing is a technology capable of mass manufacturing components with complicated geometry and coating substrates in hard-to-reach areas. In addition, cold spray also has the ability of conducting a green manufacturing process, with zero waste of renewable feed material, and zero gas and chemical emission. This paper investigates solely cold spray as an additive manufacturing technology with cork as the natural material. CFD results were used to predict the physical behavior of air and the cork particles. After unsuccessful coatings, final results showed that when moisture is added, cork is successfully cold sprayed, and agglomeration is experienced. …
Survey Data On Energy And Fuel Use Of Firms In Economic Zones In The Philippines,
2021
Ateneo de Manila University
Survey Data On Energy And Fuel Use Of Firms In Economic Zones In The Philippines, Majah-Leah V. Ravago, Raul V. Fabella, Karl Robert L. Jandoc, Renzi G. Frias, J. Kathleen P. Magadia
Economics Department Faculty Publications
The data describe characteristics, operations, utilities, and fuels used in the production of 115 manufacturing and agro-industrial firms in Philippine special economic zones. The data include information on the firm's production, sales, and schedules; electricity sources, requirements, and uses; the importance of various conventional fuels, and the firms’ fuel expenditure in their major production processes. The data also include their employee's aptitude, knowledge, considerations, and opinions on alternative fuels and primary energies, and experiences in using them. The data were gathered through a series of focus group discussions (FGDs) in June 2019 and an online survey conducted in August to …
Drug-Based Therapeutic Strategies For Covid-19-Infected Patients And Their Challenges,
2021
The University of Texas Rio Grande Valley
Drug-Based Therapeutic Strategies For Covid-19-Infected Patients And Their Challenges, Khatereh Zarkesh, Elaheh Entezar-Almahdi, Parisa Ghasemiyeh, Mohsen Akbarian, Marzieh Bahmani, Shahrzad Roudaki, Rahil Fazlinejad, Soliman Mohammadi-Samani, Negar Firouzabadi, Majid Hosseini, Fatemeh Farjadian
Manufacturing & Industrial Engineering Faculty Publications
Emerging epidemic-prone diseases have introduced numerous health and economic challenges in recent years. Given current knowledge of COVID-19, herd immunity through vaccines alone is unlikely. In addition, vaccination of the global population is an ongoing challenge. Besides, the questions regarding the prevalence and the timing of immunization are still under investigation. Therefore, medical treatment remains essential in the management of COVID-19. Herein, recent advances from beginning observations of COVID-19 outbreak to an understanding of the essential factors contributing to the spread and transmission of COVID-19 and its treatment are reviewed. Furthermore, an in-depth discussion on the epidemiological aspects, clinical symptoms …
A Framework Of Dynamic Data Driven Digital Twin For Complex Engineering Products: The Example Of Aircraft Engine Health Management,
2021
The University of Texas Rio Grande Valley
A Framework Of Dynamic Data Driven Digital Twin For Complex Engineering Products: The Example Of Aircraft Engine Health Management, Zhenhua Wu, Jianzhi Li
Manufacturing & Industrial Engineering Faculty Publications
Digital twin is a vital enabling technology for smart manufacturing in the era of Industry 4.0. Digital twin effectively replicates its physical asset enabling easy visualization, smart decision-making and cognitive capability in the system. In this paper, a framework of dynamic data driven digital twin for complex engineering products was proposed. To illustrate the proposed framework, an example of health management on aircraft engines was studied. This framework models the digital twin by extracting information from the various sensors and Industry Internet of Things (IIoT) monitoring the remaining useful life (RUL) of an engine in both cyber and physical domains. …
Experimental Investigation Of Additive Manufacturing Of Continuous Carbon Fiber Composites With Multifunctional Electro-Tensile Properties,
2021
Missouri University of Science and Technology
Experimental Investigation Of Additive Manufacturing Of Continuous Carbon Fiber Composites With Multifunctional Electro-Tensile Properties, Ritesh Ghimire, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Manufacturing processes for monofunctional and multifunctional materials vary depending on the design optimization. Multifunctional continuous carbon fiber composites provide great potential in achieving coupled structural and electrical properties for their applications in aircraft, unmanned aircraft systems, and spacecraft. Proper optimization of tensile and electrical properties offers benefits early in the design and continuous operational safety phases to obtain coupled multifunctional properties. In this paper, fused filament fabrication additive manufacturing (AM) technique was used to fabricate continuous carbon fiber solid laminated composites test coupons. The proposed new method characterizes the electrical conductivity's coupled effects on the tensile properties, including the failure …
Construction Of Spatial Filtering Matrices For Norm-Optimal Ilc In Single Point Incremental Forming,
2021
Missouri University of Science and Technology
Construction Of Spatial Filtering Matrices For Norm-Optimal Ilc In Single Point Incremental Forming, Joseph D. Fischer, Mitchell R. Woodside, Douglas A. Bristow, Robert G. Landers
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Iterative Learning Control (ILC) is a control technique used to improve performance in repetitive processes. ILC has grown in popularity in part due to its ease of implementation and ability to achieve high levels of accuracy even in complex nonlinear systems. However, a fundamental limitation of ILC is that it relies on system repetition, making the impact of non-repetitive disturbances (e.g., noise) on the controller's performance severe. Much work has been done to reject noise in the time domain; however, little has been done to address noise which is spatial in nature. In this work, a method for limiting noise …
Additive Manufacturing Of Stainless Steel -- Copper Functionally Graded Materials Via Inconel 718 Interlayer,
2021
Missouri University of Science and Technology
Additive Manufacturing Of Stainless Steel -- Copper Functionally Graded Materials Via Inconel 718 Interlayer, Xinchang Zhang, Lan Li, Frank W. Liou
Mechanical and Aerospace Engineering Faculty Research & Creative Works
The joining of dissimilar materials is becoming increasingly prevalent to integrate different material properties to enhance design flexibility and overall performance. This study introduced an innovative approach to additively manufacture copper on 316L stainless steel (SS316L) via Inconel 718 interlayers using directed energy deposition (DED). The novel multi-material structure was studied both experimentally and theoretically. The microstructure, tensile properties, microhardness, and thermal performance of the structure were characterized. Residual stress distribution over the structure was revealed by experimental-validated numerical modeling. The result exhibits that defect-free structures with excellent interfacial bonding can be achieved by introducing Inconel 718 interlayers. The bonding …
A High-Pressure Shear Testing Approach To Measure Flow Stresses Near A Friction Stir Welding Tool,
2021
Brigham Young University
A High-Pressure Shear Testing Approach To Measure Flow Stresses Near A Friction Stir Welding Tool, David Prymak, Michael Miles, Tracy W. Nelson, Fredrick Michael
Faculty Publications
A new approach for measuring flow stresses near a spinning friction stir welding (FSW) tool is evaluated on AA 6061-T6 plate. The test consists of plunging a cylindrical tool with a flat face into the plate at different rotational speeds, using a variety of constant vertical loads. A viscosity-based model of the shear layer created under the tool is employed to estimate local flow stresses. The flow stresses measured by this approach exhibited an inverse relationship with temperature and a positive dependence on the pressure imposed by the spinning flat-faced tool. Compared to hot compression and hot torsion results, estimated …
Manufacturing: The Qualitative Study Of A Transition To A Green Facility,
2021
Western Kentucky University
Manufacturing: The Qualitative Study Of A Transition To A Green Facility, Brandon David Staves
Masters Theses & Specialist Projects
This qualitative study focused on answering three core questions: How have facilities reduce pollutions in regards to the quality of air, water, land, light and noise? Which Types of pollution reduction projects are more or less successful to implement? What types of pollution are facilities focusing on and why? The results of the 15 companies surveyed show a variety of projects that facilities have used to reduce pollution, it also shows that cost is a major factor in the unsuccessful projects, and that facilities are actively focused on reducing Air, Land, and Water pollution. While the data shows a variety …
The Impact Of Gemba Walks On Preventative Maintenance Productivity,
2021
Western Kentucky University
The Impact Of Gemba Walks On Preventative Maintenance Productivity, Jake Donald Taylor
Masters Theses & Specialist Projects
Gemba Walks are a tool to get management involvement in areas where the work is taking place. Gemba Walks allow individuals involved first-hand to voice and reduce waste within the process and general operations. This research measured the benefits and improvements Gemba Walks had on the availability of equipment. For example, reducing the number of events that equipment is down for maintenance and its duration to repair these events, therefore improved availability. Maintenance is a critical aspect of keeping a company running, and making improvements found during this research significantly impacted the company by creating lean improvements. The improvements focused …
