Heat Transfer, Combustion Commons^™

Heat And Mass Transfer Modeling Of High-Temperature Moving-Bed Thermochemical Reactors, David Korba

Theses and Dissertations

With the global deployment of renewable energy generation at record rates, clean energy is steadily becoming competitive with its fossil-fuel counterparts. However, further expansion is limited by the inherent intermittency of renewable energy sources (solar, wind, wave, etc.), which typically do not match with daily and seasonal variations of global (and local) energy demand. Thermochemical energy storage (TCES) has demonstrated strong potential in being a technological pathway to provide on-demand process heat and handle the intrinsic variations in renewable energy generation and energy demand. TCES works on the premise of excess renewable heat driving an endothermic reduction reaction, in which …

Applications Of Large Eddy Simulations To Novel Internal Combustion Concepts, Patrick O'Donnell

All Dissertations

Computational fluid dynamics (CFD) simulations of internal combustion engines (ICEs) are becoming an increasingly popular tool in the automotive industry to either explain experimentally observed trends or perform lower cost design iterations. The convenience of commercially available CFD software and advancements made in computing hardware have been the impetus behind this growing popularity. However, obtaining accurate results using these software packages is not a trivial process and requires an in-depth understanding of the underlying numerical methodology and sub models for various physical phenomena. Specific to the ICEs, CFD simulation often entails the use of models for detailed chemistry and combustion, …

Measurement Of Conduction, Radiation, And Convection Thermal Energy To Assess Baking Performance In Residential Ovens., Sean Simpson

Electronic Theses and Dissertations

Residential ovens are complicated thermal environments capable of delivering convection, conduction, and radiation heat transfer to food. The amount and mode of heat transfer can change based on the design of the oven cavity, cooling systems, and oven cycle algorithms. Studies have shown that the changes in one heat transfer mode can have an impact on the quality of baked goods. The many variables involved make designing residential ovens a time consuming and costly process. The goal of this study is to adapt thermal energy sensing technology to collect energy data from a residential oven and develop correlations to quality …

Performance And Emissions Study Of N+3 And N+4 Engine Models With Several Fuel Types Using Npss, Abel Solomon

McKelvey School of Engineering Graduate Student Theses & Dissertations

The aviation industry is known to be one of the major contributors to greenhouse gases accounting for 4.9% of the global greenhouse emissions. With the ever-increasing threat of climate change to the overall survival of the planet, the exploration of new technologies and alternative energy sources that minimize greenhouse gas emissions are of paramount importance. In this regard, the development of propulsion systems well suited for the performance and emissions requirements of future commercial aircraft plays a crucial role. This thesis investigates N+3 and N+4 technology-level propulsion systems that are proposed by NASA as possible propulsion systems for advanced single-aisle …

Healthcare Built Environment And The Covid-19 Pandemic, A Mixed-Method Study, Mohammad Saleh Nikooopayan Tak

All Theses

The outbreak of COVID-19 presented an unparalleled risk to public health, leading to urgent scientific efforts in understanding transmission mechanisms and mitigating risks, especially in healthcare settings. This mixed-methods study examines knowledge advancement regarding indoor air quality in healthcare facilities during the pandemic. A systematic literature review of 163 post-COVID studies identifies key research thrusts and 31 recommendations related to building ventilation, air filtration, surface disinfection, and monitoring. Comparison with over 200 pre-pandemic publications reveals both reliance on established infection control principles and unique contributions, such as detecting viral RNA in air and surface samples indicating potential airborne and fomite …

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …

Advances In Spacecraft Thermal Control, Sandra K. S. Boetcher, Robert C. Consolo Jr.

Publications

Spacecraft thermal management is critical for ensuring mission success, as it affects the performance and longevity of onboard systems. A comprehensive overview of the state of the art in spacecraft thermal control solutions, as well as a design methodology framework for efficient and effective thermal management, is provided. Various thermal control solutions, including coatings, insulation, heat pipes, phase-change materials, conductive materials, thermal devices, actively pumped fluid loops, and radiators, are discussed along with the primary sources of heat loading in space. The need for accurate modeling and analysis of the thermal environment to identify appropriate thermal control solutions and design …

Addressing Low Heat Pump Heating System Sales In The Uk, Ben Costelloe

Articles

The replacement of existing fossil fuel boilers with heat pumps is seen as a key measure in the decarbonisation of heating systems and addressing climate change. This policy however, is currently failing in many Western European states, particularly in the UK. The many reasons for this situation are examined. However, the age of UK housing stock and particularly the high number of dwellings built prior to the introduction of building insulation regulations in 1980, are key. To maintain the running cost of air source heat pumps competitive with those of the gas boilers they generally replace the heat pump lift …

Flat Plate Solar Collector For A Tiny Home, Clarice Leslie Nicholas

Honors Projects

Pallet Shelter is a company that builds tiny houses for the homeless. We partnered with them to build a solar water heater for their homes so that their tenants can have hot running water. The collector panel sits on the roof of the shelter and absorbs the energy of the sun and uses it to heat water flowing through an array of copper pipes. The hot water is then stored in an insulated tank inside the shelter.

Cooled Liquid Rocket Thrust Chamber, Benjamin Gibson, Kealan Frederick Harris, Ryan Frank Schackel, Bjorn Thorsen

Mechanical Engineering

Cooling may affect the thrust output of a small-scale rocket. Little research is published about small-scale rocket performance. We hypothesize the thrust produced varies as the amount of cooling varies. To facilitate assessing this hypothesis, we have designed and built a liquid rocket engine rated for at approximately 25 lb_f of thrust. Our objective was to build in parallel with Cal Poly Space Systems, who built a rocket engine with similar specifications except without cooling. Our challenge is to integrate film cooling, so that the effects of cooling may be compared to Cal Poly Space System’s engine which has …

Statistical Uncertainty Of The Ignition Time, Burning Rate, And Extinction Characteristics Of Engineered Timber Products, Jacob David

Master's Theses

The characterization of flammability parameters such as time to ignition, mass loss rate (MLR), and extinction criteria is critical for understanding ignition and burning behavior of timber products. These parameters, often determined with bench scale experiments, have previously been presented in literature. However, standard test methods generally use relatively low trial quantities (e.g., n=3) which can potentially cause large variation in reported values. This study investigates the influence of trial quantity on observed statistical variation in key flammability metrics for timber products (e.g., ignition time, peak MLR, MLR at extinction). Using a conical heater, 100 repeat trials were conducted …

Flexible Water Cooling, Joshua Terlaje, Andrew Lin, Nicholas Morales, Tanner Parrott

Mechanical Engineering

The goal of this project is to develop and deploy a water-cooling system to reduce the danger of heat exhaustion among communities of farmworkers. Currently, it is difficult to keep chilled water available throughout the workday when using portable water coolers. The idea uses a refrigeration system to chill the water supply by using the power take-off (PTO) on farm equipment and a corresponding generator to get around this restriction.

The project places a strong premium on keeping the chilled water supply at a maximum temperature of 59°F to ensure compliance with the California Department of Industrial Relations' requirements. Each …

Thermal Transport And Physical Characteristics Of Silver-Reinforced Biodegradable Nanolubricant, Jaime Taha-Tijerina, Karla Aviña, Nicolás Antonio Ulloa-Castillo, Dulce Viridiana Melo-Maximo

Informatics and Engineering Systems Faculty Publications

In this investigation, the thermal transport behavior of biodegradable lubricant reinforced with silver nanostructures (AgNs) at various filler fractions of 0.01, 0.05, 0.10, and 0.20 weight percent was evaluated over a temperature scan analysis, ranging from room temperature up to 60 °C. The experimental results revealed significant gradual enhancements in thermal conductivity as AgNs concentration and evaluating temperatures were increased. These improvements showed the important role of nanostructures’ interaction within the biodegradable lubricant. The thermal conductivity performance improved for nanolubricants ranging from 6.5% at 30 °C and 0.20 wt.% AgNs content up to a maximum 32.2%, which was obtained at …

Atmospheric Carbon Capture: A Review On Current Technologies And Analysis Of Energy Consumption For Various Direct Air Capture (Dac) Systems, Jennifer Perskin

Doctoral Dissertations and Master's Theses

Carbon dioxide (CO₂) capture is a crucial approach to reducing greenhouse gases in the atmosphere to directly combat climate change. Major components of the technology to desublimate CO₂ at cryogenic temperatures are mature and have the potential to be applied to build large Arctic/Antarctic direct-air CO₂ capture plants. Pressure swing adsorption another gas separation technique used in industry today that can be modified for atmospheric carbon capture. The discussion of energy consumption for cryogenic and combined direct air capture systems is explored in this study. The investigation of precompression of atmospheric air for a direct-air capture …

Reynolds-Averaged Navier-Stokes Cfd Simulation Of High-Speed Boundary Layers, Michael Tullis

Mechanical Engineering Undergraduate Honors Theses

This paper presents an investigation of Reynolds-averaged Navier-Stokes (RANS) turbulence models used in computational fluid dynamics (CFD) simulations of boundary layer flow and heat transfer in high Mach number flows. This study evaluates an industry standard RANS turbulence model (k-omega SST) and a recently proposed modification to that model (Danis and Durbin [1]), and quantifies the accuracy for predicting high Mach number boundary layer flow. The test cases were previously documented by Duan et al. (2018), who used direct numerical simulation (DNS) to calculate boundary layer flow of an ideal gas over a flat plate at freestream Mach numbers ranging …

A Systematic Study Into The Design And Utilization Of Burn Wire As A Means Of Tensioning And Releasing Spacecraft Mechanisms Through Applied Joule Heating, Chandler Dye

Mechanical Engineering Undergraduate Honors Theses

The joule heating characteristics of Nichrome burn wires, often used as a thermal cutting device in mechanisms designed to fasten and release CubeSat deployables, are examined in the following thesis. Wires ranging from 0.125 inches to 2 inches long, and diameters of 30 Ga and 40 Ga, are investigated through analytical calculations and thermal simulations based on heat transfer due to joule heating, and through physical circuitry-based experiments. The temperature data is used to generate heating curves to predict the time it takes for Nichrome wires to fail under varying testing parameters. This research aims to catalog a series of …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

Pla-S-Tech: Pla Sustainable Technology, Sean Sapper, Ryan Decarlo, Elle Whitney, Samantha Dombrowski, Dalton Prokop, Dominic Zaio, Tyler Stokes, David Deese, Blake Hengel, Yi Guo

Mechanical and Civil Engineering Student Publications

To recycle waste material produced by fused deposition modeling (FDM) 3D printers, a recycler was designed and manufactured to convert plastic scraps into usable filament. The device does so by breaking down plastic material to a uniform size with the shredder, melting and compressing these pieces into a cylindrical strand with the extruder, and wrapping this strand around a filament spool with the spooler. As the device is mostly made from commercially-available components, it is easily maintainable and user-serviceable, while also costing less than similar devices on the market.

Thermal Boundary Condition Effects On Local Supercritical Co2 Heat Transfer Trends In Tubes, Nicholas C. Lopes

Doctoral Dissertations and Master's Theses

Supercritical carbon dioxide (sCO2) is a promising heat transfer fluid for the refrigeration and power generation industries due to its unique thermal properties and low environmental impact. To understand it as an alternative to traditional working fluids, the thermophysical and heat transfer phenomena of sCO2 are often studied using simplified geometries (tubes). Focus has been placed on investigating averaged heat transfer trends under an array of flow conditions with either a constant wall heat flux, constant wall temperature, or conjugate thermal boundary condition. Less emphasis has been placed on studying local sCO2 heat transfer developments. Tubular sCO2 numerical models that …

Experimental And Numerical Analysis Of A Commercial Phase Change Material Melting At Different Inclinations, Andrew Heiles

Doctoral Dissertations and Master's Theses

The study of various phase change materials (PCM), experimentally and numerically, have been completed over the past several years to address their feasibility and potential when used in latent heat thermal energy storage (LHTES) systems for a variety of potential applications. Previous studies have investigated changes into the type of PCM used in the system as well as the system configuration, ranging from boundary conditions to internal and external geometries and orientations of the system. The present study focused on conducting experiments at different inclination angles and isothermal wall temperatures with the organic PCM PureTemp37, and continued with a numerical …