Energy Systems Commons^™

Engineering A Novel Solvent Regenerator That Leverages Electrochemically Induced Ph Swings For Direct Air Capture And Hydrogen Generation, Emmanuel Aluhunmile Ohiomoba

Theses and Dissertations--Mechanical and Aerospace Engineering

Direct Air Capture (DAC) is considered to be a key component for achieving global net-negative emissions. However, to capture CO₂ at the low concentrations in the atmosphere requires materials with high affinity for CO₂. This makes the solvent-based chemical approach for DAC more applicable compared to physical approaches. Nonetheless, regenerating the capture solvent presents a significant challenge due to high heat requirements for thermal decomposition of carbonates. Leveraging electrochemical principles provides an opportunity to simplify the regeneration process, thus, this work focuses on engineering an electrochemical solvent regenerator for recovering alkaline solvents for DAC, with co-production of …

Intelligent Systems For Synergistic Optimization Of Vehicle Dynamics And Energy Consumption In Connected And Automated Vehicles, Aman Poovalappil

Dissertations, Master's Theses and Master's Reports

This dissertation focuses on the development and validation of on-board, real-time estimation algorithms and the investigation of energy-saving strategies for modern light-duty vehicles, including connected and automated vehicles (CAVs). The accurate estimation of key vehicle parameters is critical for enhancing energy efficiency, enabling advanced driver-assistance systems (ADAS), and optimizing vehicle performance and energy efficiency. First, this research introduces a novel real-time algorithm to dynamically learn vehicle mass using readily available sensor data. Based on longitudinal vehicle dynamics, a sensitivity analysis was conducted to identify the conditions under which mass estimation is most robust. The algorithm was extensively validated through on-road …

Holistic Energy Efficiency Analysis Of Electrified Off-Highway Material Handler: From Drive Cycle Characterization To Powertrain, Hydraulic, And Thermal System Performance, Alexander Czarnecki

Dissertations, Master's Theses and Master's Reports

Three complexities surrounding the operation and testing of hybrid electric, heavy-duty nonroad machines have been addressed experimentally and using 1D simulation. Their resolutions have been intertwined with the development of a prototype machine that was proven to reduce fuel consumption in excess of 20%. A real-world drive cycle that leveraged hydraulic cylinder position was developed and utilized to ensure accurate reproduction of hydraulic work between the baseline and hybrid machines, while simultaneously maintaining less than 5% RMS error in position for main load handling functions. The newly developed, machine-specific drive cycle also contributed towards making equivalent comparisons in energy consumption …

Study Of Two-Phase Void Fraction In A Rectangular Channel Using Capacitance Sensor, Peter Ngoc Nguyen

Dissertations, Master's Theses and Master's Reports

Two-phase liquid-gas flow has many applications in the nuclear industry, including active heat exchangers, reactor core designs, secondary steam generators, and two-phase flow loop balance of the plant. The void fraction is a crucial parameter to determine the pressure drop, flow regimes and liquid levels inside the nuclear reactor core. For the past forty years, void fraction has been studied by many researchers by different measurement techniques. Each method has positive and negative attributes. In this study, after extensive literature reviews, the author has chosen a capacitance type void fraction sensor over other void fraction measuring techniques. The principal concept …

Knowledge Integrated Deep Learning For Enhanced Fault Diagnosis And Prognosis For Rotating Machinery And Its Applications On Marine Systems, Yunsheng Su

Dissertations, Master's Theses and Master's Reports

This dissertation develops a knowledge-informed deep learning framework for robust fault diagnosis and prognosis across various engineered systems, including bearings, lithium-ion batteries, and mooring systems in wave energy converters (WECs). A deep transfer learning (DTL) method is first developed to improve bearing fault diagnosis by fusing data from multiple sources and extracting key features using convolutional neural networks (CNNs). Building upon this, a knowledge-informed deep network (KIDN) framework is proposed, integrating physics-based features with deep learning to enhance diagnostic accuracy and generalizability. A constrained Gaussian process (CGP) model is further employed to guide adaptive network design and reduce model tuning …

High Voltage Junction Box For Demonstrator Vehicle, Benjamin Lubowicki, Ryan Dorste

Williams Honors College, Honors Research Projects

Schaeffler, our industry sponsor for this project, is designing a battery pack for a demonstration vehicle that requires a high voltage junction box to route power to the vehicle. The project type is a unique design of a mechanical component, mechanism, and process. Our objective for this project is to assemble provided electro-mechanical components into an enclosure following a provided electrical diagram. The expected deliverables are the following: 3D CAD assembly of final product, FEA analysis of designed components, 2D print of final product, fabrication and assembly of designed parts, technical report documenting design process and installation. The skills required …

Frictionless System For Planetary Simulant Testing, Hailey Zackiewicz, Morganne Neuman

Williams Honors College, Honors Research Projects

The engineering design process is used to create a frictionless system for planetary simulant testing. Research about different types of bearing is used to brainstorm ideas about how to construct a tray and rail system with minimal friction. Using thought-walkthroughs and a weighted decision matrix, it will be determined which ideas can move forward with a tabletop experiment. Based on the results of the experiment, it will be determined which system will be fabricated and installed for the testing system.

Nebraska Test #2302: Claas Xerion 12.650 Terra Trac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test# 2299: Claas Xerion 12.590, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2296: John Deere 9rx 710, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2268: Case Ih Steiger 595, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Test #2269: Case Ih Steiger 645, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1294: Fendt 620 Vario, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1292: Fendt 616 Vario, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1298: Fendt 726 Vario Gen 7.1, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

3d Printing Of A Solid-State Battery, Maurizio A. Brozzi

Honors Undergraduate Theses

Solid-state battery research has gained significant attention in recent years, as it provides a unique solution for several common issues in conventional Li-ion batteries. Additionally, as additive manufacturing technologies continue to advance, they have the potential to fabricate solid-state batteries with new materials. The objective of this study is to explore the feasibility of 3D printing of a solid-state battery. By creating an initial PEO-PSF hybrid polymer matrix dissolved in DMSO and adding a lithium salt, the base electrolyte ink was formed. With the addition of conductive additives and active material, electrode inks were also produced. Super P was used …

Design And Lab Implementation Of An Air Source Transcritical Co2 Heat Pump, Geoffrey Turbeville

Dissertations and Theses

A laboratory-scale air-source transcritical CO2 heat pump (TCHP) was developed to evaluate the performance of low-global-warming-potential (GWP) refrigerants for cold climate applications. A custom climate chamber was also constructed to simulate winter weather conditions typical of the northeastern United States. Both the TCHP and the chamber were fully instrumented to collect temperature, pressure, and mass flow data, which were used to calculate the co- efficient of performance (COP) in accordance with ASHRAE standard refrigerant enthalpy methods. Prior to testing the CO2 system, the experimental setup was benchmarked using a commercially available R410A heat pump manufactured by LG.

The climate chamber …

Advanced Air Preheater Sealing Systems For Enhanced Efficiency And Reliability In Thermal Power Plants, Pavan Kumar Ravulaparthy

Theses and Dissertations

Global electricity generation still relies heavily on thermal power plants, which consume vast amounts of fuel and emit significant amounts of carbon dioxide. A major but often overlooked source of inefficiency in these plants lies within the rotary regenerative air preheater (RAPH), a critical heat-exchange component where air leakage can exceed 20% in aging units. This leakage increases fuel consumption, parasitic fan power, and CO₂ emissions, while degrading boiler reliability.

This research introduces advanced adaptive sealing systems designed to mitigate these losses by dynamically compensating for rotor eccentricity, thermal distortion, and wear under harsh operating conditions. Brush seals, composed of …

Trustworthiness And Trust: Identifying Factors That Drive Successful Human-Ai Interaction In Nuclear Power Plant Applications, Yusuke Yamani, Austin Jackson, Casey Kovesdi, Jeffrey Joe, Jeremy Mohon

Psychology Faculty Publications

Emerging technologies such as artificial intelligence (AI) and machine learning are rapidly evolving and promising tools for efficient and continued safe operations of the U.S. nuclear power plants (NPPs). Emerging AI techniques like large language models (LLMs) are one such technology that may help personnel at existing NPPs perform work more efficiently. For example, operators may query the current operational status of a power plant via a chat interface, leveraging LLMs to access plant-related information in an interactive manner rather than manually collecting various sensor data for surveillance or work order tasks. This is a fundamental shift in the way …

Multiphysics Modeling Of Solid Oxide Fuel Cells For Gradient Minimization And Inductive Loop Analysis In Impedance Spectroscopy Using Machine Learning-Based Microstructural Property Estimation, Muhammad Usman Khan

College of Graduate Studies: Theses & Dissertations

Solid oxide fuel cells have significant advantages in renewable energy utilization due to their high efficiency, fuel flexibility, and low emissions. However, despite the numerous efforts of technology, thermal and current density gradients and impedance behavior fluctuations are still causing performance degradation. A combined computational framework that integrates machine learning and three-dimensional Multiphysics modeling is needed to investigate and optimize the performance of solid oxide fuel cells. A machine learning model, trained on synthetic microstructure data by percolation analysis, is used to predict important microstructural parameters like triple phase boundary density and geometric tortuosity. These are then employed in a …