Electro-Mechanical Systems Commons^™

An Analysis Of Testing Variables In Rapid Compression Machine Experiments, Jenna Ezzell

Master's Theses (2009 -)

There have been discrepancies noted with regards to experimental data from rapid compression machines (RCM). When data is compared from different RCM facilities, the ignition delay times are inconsistent when inspecting any particular temperature. Currently in publications, if these datasets are compared, the discrepancy is said to be due to heat loss, however this issue has yet to be examined more thoroughly. To determine what the root cause of this discrepancy is, four different fake RCM facilities were created and simulated. There were also different sets of initial conditions used to determine how this may affect the data. They were …

Remote Cable Gantry, Allen L. Bailey

Electrical Engineering

The Remote Cable Gantry is a robotic system that was initially intended to aid in the art of aerial videography. It was designed to enable novice and expert users alike to capture both video footage and audio from perspectives unachievable by current methods. This system uses a series of cables to control the position of a camera gimbal in a defined 3D space and, as a self-contained unit, is portable and easy to use. The Remote Cable Gantry offers a quiet, intuitive, and safe alternative to existing technology, which has been limiting the market and potential of aerial photography and …

Guided Target Control System Final Design Report, John Barry, Zachary Eagan, Ryan Mackintosh

Mechanical Engineering

Daimler Automotive, the parent company of Mercedes-benz requires improved methods for testing their Autonomous Emergency Braking Systems. To this end they have presented a series of four senior projects to California Polytechnic State University in San Luis Obispo. One of the Projects is to build a facsimile of a human crossing the street. The other three projects of which this is a part; are to produce an autonomous car facsimile. These projects are intended for use in testing new Autonomous Emergency Braking Systems and may serve as the basis for future senior projects.

Small-Scale Intelligent Vehicle Design Platform, Christopher Grant, Jay Miley, Evan Phillips

Mechanical Engineering

Intelligent Vehicle Design is a growing field with the potential to save many lives by actively minimizing the impacts of human error. Though there are many ways to research intelligent vehicle control, full-scale implementations are expensive and dangerous and computer simulations have extremely steep learning curves. Researchers and students need an accessible, adaptable, and robust development platform to rapidly create and test autonomous control algorithms. While small-scale platforms are often designed from the ground up for specific projects, this requires analysis, design, and manufacture. The goal of this project is to develop a small-scale intelligent vehicle that can be configured …

Blend It Wine Blending Distribution System, Connor Clarry, Russell Temple, Matt Moren

Mechanical Engineering

No abstract provided.

Micro-Spi Sediment Profile Imaging Micro-Inspector, Andrew P. Corvin, Caleb T. Davies, Matt R. Ferrari

Mechanical Engineering

This project was proposed by Dr. Brian Paavo through a desire to more easily study the benthic sediment layers of the ocean. To do so, he asked us to build a simple and compact machine for use in sediment profile imagery (SPI). Although devices like this already exist, they are all large scale devices that require a ship with a crane to deploy, which is expensive and time consuming. Instead, he desired a “micro” SPI, which is capable of being deployed from a small vessel that can easily navigate shallow waters. Our interpretation of these requirements was as follows: a …

Drawing And Twisting Of Graphene Fibers, Gregory T. Lane, Robert J. Sekerak, Isaias Diaz

Mechanical Engineering

The aim of this project was to develop a more automated process for drawing and twisting of graphene fibers than was currently in place. This was implemented by having two chemical baths with variable speed rollers at either end, and intermediate roller to spool fiber between stages, and a twisting cylinder with integral spool to twist the fiber as it is collected. The goal was to have this first iteration deliver a working prototype, however due to manufacturing delays and timing constraints, that will be missed. A second follow-on project would be able to continue the work presented here and …

X-Beam Alignment System, Whittaker Ian Hamill, Joseph Michael Falcao, Robert Kim-Yan Tam

Mechanical Engineering

The goal of the project was to design, build, and test an automated machine for Micro-Vu that will align a pair of rails to the necessary precision and affix said rails to Micro-Vu's X-Beam as to reduce manual labor and human error.

Marine Gastrobot Final Design Report, Wesley B. Williams, Eric Kane Dreischerf, Tommy Nicholas Yath

Mechanical Engineering

The Marine Gastrobot sponsored by Dr. Christopher Kitts of the Cal Poly Center for Applications in Biotechnology was a research and development effort intended to explore the use of microbial fuel cell technology as a power source for underwater robots. Our team Ocean Locomotion succeeded in developing a first iteration of an underwater robotic platform suitable for microbial fuel cell integration. The primary feature of the design is its sinusoidal fin propulsion intended for benthic exploration with limited risk of entanglement. During the course of development, Ocean Locomotion explored the use of low power actuation methods and determined their limited …

Blood-Brain Barrier-On-A-Chip Systems Based On 3d Printing, Cade I. Harding

Mechanical Engineering Undergraduate Honors Theses

This research focused on the design and testing of a blood-brain barrier (BBB)-on-a-chip microfluidic device produced using 3D printing. First, COMSOL simulations were used to define dimensions of the microchannel that would most accurately replicate the flow environment imposed on the blood-brain barrier, the wall shear stress being the most important characteristic. In using COMSOL, water was used as the simulated fluid and also the testing fluid in the fabricated devices. Therefore, the microsystem is designed to produce the BBB environment using water instead of blood. The numerical simulation parameters were based on theoretical calculations performed to scale up the …

Chip-Package Interfacial Stress Analysis And Reliability Implications For Flip-Chip Power Devices, Jonathan Gh Treco

Mechanical Engineering Undergraduate Honors Theses

The solder in flip-chip assemblies experience high stress and strain because of thermal mismatch induced deformation. These deformations occur because of the differences of coefficient of thermal expansion between flip-chip assembly materials. The similarly in stress profiles between thermal induced and shear induced stress in solder joints enable the use of die shear testing as a representative technique for relating the max stress the flip-chip can withstand to cyclic thermal fatigue failures. In this work, two electronic device sample preparation types are evaluated: One set of samples are soldered together and other set of samples use epoxy as an adhesive. …

System-Layout-Dependent Thermally Induced Solder Stress & Reliability Implications, Ange C. Iradukunda

Mechanical Engineering Undergraduate Honors Theses

Electronic flip chip assemblies consist of dissimilar component materials, which exhibit different CTE. Under thermal cyclic operating conditions, this CTE mismatch produces interfacial and interconnect stresses, which are highly dependent on system layout. In this paper, sensitivity analyses are performed using ANSYS FEA to establish how the proximity and arrangement of neighboring devices affect interconnect stress. Flip chip alignment modes ranging from edge-to-edge to corner-to-corner are studied. Results of these FEA studies, demonstrated that closely packing devices together has the effect of making them act as one. This results in a significant increase in the thermomechanical stresses induced on peripheral …

Safer Sweep Auger Operation Using Robotics, Nathan A. Wulf

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis presents a remotely controlled robotic solution for those who must sometimes enter agriculturally confined spaces in attempts to assist with grain bin cleanout, particularly by manipulating the sweep auger. In 2015 alone, there were at least 47 documented incidents that occurred in agriculturally confined spaces, of which more than half were fatal. While there have been several advancements in the quality and effectiveness of sweep augers, there have been very few that offer the safety and adaptability of the robotic solution proposed. This robotic solution is a four-wheeled, skid-steering style robot with camera and lighting attachments that allow …

Size Distribution Of Carbon Nanoparticles From A Methane/Argon Hv Pulsed Dc Ampj, Steven Doyle

Research Horizons Day Posters

No abstract provided.

Formation Of Mound-Like Multiscale Surface Structures On Titanium By Femtosecond Laser Processing, Edwin Peng, Alfred Tsubaki, Craig A. Zuhlke, Ryan Bell, Meiyu Wang, Dennis R. Alexander, George Gogos, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Surface Functionalization Technique • Femtosecond Laser Surface Processing (FLSP) • Utilize high power, femtosecond (10-15 s) laser pulses • Produce self-organized, multiscale surface micro/nanostructures • Diverse range of applicable substrates: semiconductors, metals, polymers, & composites

Why? • What are the different types of FLSP structures on Ti? • Physical evidence needed for FLSP formation models • Optimize FLSP of Ti for biomedical & other applications

How? • Obtain evidence of mound growth processes by examining underlying microstructure • Utilize dual beam Scanning Electron Microscope-Focused Ion Beam instrument to cross section surface structures & fabricate transmission electron microscopy samples

Developing A Curriculum For Marine Mechatronics Technicians, Vukica M. Jovanovic, Petros J. Katsioloudis, Ana Djuric, Mileta Tomovic, Thomas B. Stout

Engineering Technology Faculty Publications

A growing trend within the U.S. Navy is to streamline operations by deploying ships with less sailors, who are more highly skilled technicians that are trained to do a wide array of jobs. Modern ships also include various automated systems that require more highly skilled technicians for maintenance. Outdated warship designs are now being replaced with industrial grade automation equipment. Such equipment is being used in warships that encounter harsher environments than what exists in the civilian industry. Hence, there is a need for training in regards to industrial grade automation equipment for military and civilian ship repair partners. Marine …

Optimized Endpoint Delivery Via Unmanned Aerial Vehicles, Fuad Gazal

All Graduate Theses, Dissertations, and Other Capstone Projects

Unmanned Aerial Vehicles (UAVs) are remotely piloted aircraft with a range of varying applications. Though early adoption of UAVs focused on military applications, surveillance, photography, and agricultural applications are presently on the rise. This work aims to ascertain how UAVs may be employed to elicit deceased transportation times, increased power efficiency, and improved safety. Resulting in optimized end point delivery. A combination of tools and techniques, involving a mathematical model, UAV simulations, redundant control systems, and custom designed electrical and mechanical components were used towards reaching the goal of a 10-kilogram maximum payload delivered 10 miles under 30 minutes. Two …

Fourth-Generation Fan Assessment Numeration System (Fans) Design And Performance Specifications, Michael P. Sama, George B. Day, Laura M. Pepple, Richard S. Gates

Biosystems and Agricultural Engineering Faculty Publications

The Fan Assessment Numeration System (FANS) is a measurement device for generating ventilation fan performance curves. Three different-sized FANS currently exist for assessing ventilation fans commonly used in poultry and livestock housing systems. All FANS consist of an array of anemometers inside an aluminum shroud that traverse the inlet or outlet of a ventilation fan. The FANS design has been updated several times since its inception and is currently in its fourth-generation (G4). The current design iteration (FANS-G4) is reported in this article with an emphasis on the hardware and software control, data acquisition systems, and operational reliability. Six FANS-G4 …

Target Read Operation Of Passive Ultra High Frequency Rfid Tag In A Multiple Tags Environment, Zi Qin Phua

Theses and Dissertations--Mechanical and Aerospace Engineering

Passive ultra-high frequency (UHF) radio frequency Identification (RFID) has emerged as a promising solution for many industrial applications. Passive UHF systems are relatively inexpensive to implement and monitor, as no line of sight is required for the communication. There are several advantages to using a passive RFID system. For example, no internal power source is required to activate the tags, and lower labor costs and efficient multitasking operations are expected in a long term scenario. However, due to factors such as tag-to-tag interference and inaccurate localization, RFID tags that are closely spaced together are difficult to detect and program accurately …

Torque Response Of Thin-Film Ferromagnetic Prisms In Uniform Magnetic Fields At Macro And Micro Scales, Soroosh Torabi

Theses and Dissertations--Mechanical and Aerospace Engineering

The non-contact nature of magnetic actuation makes it useful in a variety of microscale applications, from microfluidics and lab-on-a-chip devices to classical MEMS or even microrobotics. Ferromagnetic materials like nickel are particularly attractive, because they can be easily deposited and patterned using traditional lithography-based microscale fabrication methods. However, the response of ferromagnetic materials in a magnetic field can be difficult to predict. When placed in a magnetic field, high magnetization is induced in these ferromagnetic materials, which in turn generates force and/or torque on the ferromagnetic bodies. The magnitude and direction of these forces are highly dependent on the type …